Why does not pull a vacuum cleaner with a bosch container

Why does the vacuum cleaner not absorb dust

It all depends on the filters and a little. on your enterprise. Some of the filters can and even need to use several times.

If the vacuum cleaner implies a paper bag for collecting dust, it is obvious that it should not be washed. But try to find him a fabric alternative. and your budget will say “Thank you”. Foam filters are also possible to wash with soap in warm water, dry and put back. usually they delay mechanical garbage, accumulate wool and large pieces of dust.

Some filters for a vacuum cleaner can and should be washed. But not all

But it is better to change the paper filters “accordion”. at home you will not clean it, even if you are sure of the opposite and armed with all kinds of rags and brushes. The same applies to HEPA filters-they account for the final stage of cleaning, and they delay finely dispersed dust, bacteria and fungi, which you can’t get rid of completely. Although, there is one reservation-fluoroplastic non-filters with labeling W, which are made of insoluble polymer in the water, you can wash with water-but at home it is not always possible to clean them qualitatively.

Check the bag

The first thing you should do is to check how filled the bag is. If the garbage filled more than 2/3 of the container, the craving can become weaker or the abyss in general when you are vacuumed. The paper bag must be replaced with a new one, t.to. It is disposable. If the container is fabric, it can be thoroughly wiped and installed back in the guides, but it is better to rinse in clean water and dry.

As a rule, in modern models of technology, the degree of clogging of the garbage bag is displayed on the case. Light indication in the form of a light bulb will burn green if the container is still empty and red, if it is time to replace.

If you cleaned, and the vacuum cleaner still does not suck well, look at the power regulator, it may be accidentally installed at least, as a result of which the device does not pull air.

Why does the vacuum cleaner not absorb, but works: reasons

When the device’s power is reduced, touch the vacuum cleaner body. If it is too hot, then the engine works under load. When revealing the technique, it must be turned off and not used until the cause of the problems is clarified. To determine the malfunction that promotes a strong heating of the unit and a decrease in sucking power, it is necessary to perform simple actions:

• Check the work capacity of the equipment after detaching the hose. If the case has stopped basking, the cause of the malfunction in the pipe or brush;
• inspect the input hole located on the case, for the lack of large garbage and other extraneous objects;
• test the performance of the device after extracting the vacuumber;
• If the equipment on continues to heat up, it is recommended to clean the filters from dirt or install new components.

In a situation where all components are checked, and the equipment continues to warm up, the problem is the malfunction of the motor. To repair the vacuum cleaner motor, you need to completely disassemble the case and change damaged parts.

note! In case of violation of the integrity of the winding on the coil, the problem can only be eliminated by the purchase of a new household device or engine.

Why the operating device is strongly buzzing and vibrates

If during cleaning the vacuum cleaner begins to buzz and heat up loudly, you should check the hose for the presence of a blockage. The accumulated garbage in the hose negatively affects the strength of traction and contributes to the appearance of loud sounds, a hum, strong vibration, uncharacteristic for the normal operation of the vacuum cleaner. Peel the hose from the extraneous components stuck inside, which prevent the normal passage of air flows, can be using wire or a long thin object.

If you do not succeed in getting rid of the hum, you need to examine the filters and the vacuumber. When polluting these elements, you need to replace worn parts and free the container from garbage. Strengthening the noise of the unit may be associated with a violation of the balancing of the impeller, damage to the bearings and other important components. If this malfunction is suspected, it is not recommended to carry out repair work on your own. The elimination of such breakdowns requires special equipment and skills.

We clean the filters

Moving further in searching for a malfunction, it is necessary to check the cleanliness of the thin cleaning filter (installed in front of the engine) and the HEPA exhaust filter, which is fixed on the back of the case behind the plastic grille. As for the first filter, it must either be completely replaced, or washed with water and dried, which depends on the universality of the material. The HEPA filter, as a rule, needs to be replaced every 50 hours of operation of the equipment so that the thrust of the vacuum cleaner does not disappear at the most inopportune moment. We checked, replaced, and the vacuum cleaner, as before, does not collect and absorb garbage well? We view the following elements of the suction system.

Life hack to increase the power of absorption

Ways to solve problems

Diagnosis only helps to find the cause of the vacuum cleaner malfunction. Further actions are aimed at eliminating the breakdown.

Vacuumber

Overflow of vacuumers with garbage is the most common problem of impairment of absorption. For any vacuum cleaner, it is not allowed to fill out the bag or capacity of more than 80%. With an increase in clogging, the craving weakens or completely disappears.

Manufacturers are equipped with expensive models with light indicators of the occupancy of the vacuumor. The green glow of the bulb signals normal work. When the indicator glows red, the vacuum cleaner is full and requires cleaning. Cheap vacuum cleaners do not have such a function. The vacuum cleaner has to be checked after each cleaning.

Eliminate the problem associated with the dirty vacuumber, just. In the cyclone, it is enough to simply throw out the garbage from the container. The one.time paper bag is only thrown away, and a new. The second time a vacuumber cannot be used. After operation and thorough shaking, the paper walls of the bag weaken. The re.installed disposable vacuum cleaner will tear off a strong stream of air, and the dust will tighten into the fan.

The fabric reusable vacuumers of the housewife always only shake. The cleaning method is good, but not effective. A large amount of dust remains between fibers of the fabric, blocking the free passage of air. Fabric bags after several times use in clean water.

The vacuumboard can be innocent if the power regulator is strongly screwed. Sometimes the rotation of the wheel allows you to solve the problem of poor absorption.

Filters of thin cleaning

Polluted vacuumboards pay attention to more often than on thin cleaning filters, and in vain. One of them stands in front of the fan. The cyclones usually be a filter by a foam plate, enclosed inside a plastic collapsible case. Foam rubber is greatly clogged with dust after each cleaning. The plate is thoroughly knocked out and rinked in water. Additionally, the plastic case of the filter on the back has a grid with small cells. It must be washed.

The second thin cleaning filter is on the exhaust of the vacuum cleaner. Usually it is made in the form of a separate box with many cells. The filter prevents the outlets of dust from the vacuum cleaner to the room. Clogged cells are cleaned with a soft brush or rinsed with clean water. Such procedures will be successful a couple of times. After 50 hours of operation, the filter must be replaced.

Components

The components of the vacuum cleaner include a corrugated hose, a telescopic handle, work nozzles. During cleaning, an accidentally drawn large object jams on bends or crossings. You can clean the hose and telescopic handle with a long stick without burrs or soft wire in isolation. The operating channel of the working nozzle is usually curved. Cleaning it is easier for something well bending: wire, cable, elastic PVC rod.

On the brush after cleaning, check the wheels. Hair is often wound on them. If the roller is equipped with bearings, they make their lubricant.

Additionally check the joints of all elements. Blaged locks, cracks and other defects create air leaks. The broken hose is immediately replaced. Temporarily rupture eliminates a transitional sleeve. The hose is cut, a piece of a plastic tube is inserted inside, the joints are clamped with clamps and wound with tape.

Electric motor

If the cause of weak traction is the electric part of the vacuum cleaner, the engine begins to work incorrectly. An extraneous noise appears, the body is very hot, the turns are reduced or “swim”.

• network cable defect;
• wear of brushes, bearings;
• pollution of the anchor collector;
• The failure of the start button or electronic unit.

It is difficult to find the reason without having basic knowledge about electrical engineering. The electric motor will have to be fully extracted, disassembled and rang all parts by a multimeter. It will be possible to change the brushes, bearings or fuses on an electronic unit on their own. The closure of the windings cannot be eliminated. Have to contact the service or buy a new motor.

There are many reasons for the poor absorption of the vacuum cleaner, and all of them negatively affect the electric motor. At the first signs of decrease in performance, you can not hesitate with the repair.

Ways to solve problems

Diagnosis only helps to find the cause of the vacuum cleaner malfunction. Further actions are aimed at eliminating the breakdown.

Vacuumber

Overflow of vacuumers with garbage is the most common problem of impairment of absorption. For any vacuum cleaner, it is not allowed to fill out the bag or capacity of more than 80%. With an increase in clogging, the craving weakens or completely disappears.

Manufacturers are equipped with expensive models with light indicators of the occupancy of the vacuumor. The green glow of the bulb signals normal work. When the indicator glows red, the vacuum cleaner is full and requires cleaning. Cheap vacuum cleaners do not have such a function. The vacuum cleaner has to be checked after each cleaning.

Eliminate the problem associated with the dirty vacuumber, just. In the cyclone, it is enough to simply throw out the garbage from the container. The one.time paper bag is only thrown away, and a new. The second time a vacuumber cannot be used. After operation and thorough shaking, the paper walls of the bag weaken. The re.installed disposable vacuum cleaner will tear off a strong stream of air, and the dust will tighten into the fan.

The fabric reusable vacuumers of the housewife always only shake. The cleaning method is good, but not effective. A large amount of dust remains between fibers of the fabric, blocking the free passage of air. Fabric bags after several times use in clean water.

The vacuumboard can be innocent if the power regulator is strongly screwed. Sometimes the rotation of the wheel allows you to solve the problem of poor absorption.

Filters of thin cleaning

Polluted vacuumboards pay attention to more often than on thin cleaning filters, and in vain. One of them stands in front of the fan. The cyclones usually be a filter by a foam plate, enclosed inside a plastic collapsible case. Foam rubber is greatly clogged with dust after each cleaning. The plate is thoroughly knocked out and rinked in water. Additionally, the plastic case of the filter on the back has a grid with small cells. It must be washed.

The second thin cleaning filter is on the exhaust of the vacuum cleaner. Usually it is made in the form of a separate box with many cells. The filter prevents the outlets of dust from the vacuum cleaner to the room. Clogged cells are cleaned with a soft brush or rinsed with clean water. Such procedures will be successful a couple of times. After 50 hours of operation, the filter must be replaced.

Components

The components of the vacuum cleaner include a corrugated hose, a telescopic handle, work nozzles. During cleaning, an accidentally drawn large object jams on bends or crossings. You can clean the hose and telescopic handle with a long stick without burrs or soft wire in isolation. The operating channel of the working nozzle is usually curved. Cleaning it is easier for something well bending: wire, cable, elastic PVC rod.

On the brush after cleaning, check the wheels. Hair is often wound on them. If the roller is equipped with bearings, they make their lubricant.

Additionally check the joints of all elements. Blaged locks, cracks and other defects create air leaks. The broken hose is immediately replaced. Temporarily rupture eliminates a transitional sleeve. The hose is cut, a piece of a plastic tube is inserted inside, the joints are clamped with clamps and wound with tape.

Electric motor

If the cause of weak traction is the electric part of the vacuum cleaner, the engine begins to work incorrectly. An extraneous noise appears, the body is very hot, the turns are reduced or “swim”.

• network cable defect;
• wear of brushes, bearings;
• pollution of the anchor collector;
• The failure of the start button or electronic unit.

It is difficult to find the reason without having basic knowledge about electrical engineering. The electric motor will have to be fully extracted, disassembled and rang all parts by a multimeter. It will be possible to change the brushes, bearings or fuses on an electronic unit on their own. The closure of the windings cannot be eliminated. Have to contact the service or buy a new motor.

There are many reasons for the poor absorption of the vacuum cleaner, and all of them negatively affect the electric motor. At the first signs of decrease in performance, you can not hesitate with the repair.

The main reasons and their elimination

The reasons why the vacuum cleaner overheats and regularly turns off can be several. Some of them, for example, a stuck item or a crowded vacuumber, can be eliminated independently. Others can only diagnose and fix the master.

The filter clogged

This is one of the most common reasons why the vacuum cleaner is warming. Modern models are equipped with special filters through which air passes. Filters delay dust, dirt, garbage and other small objects. Over time, the filter cells are clogged, the air passes with difficulty, and overheating occurs.

Possible causes of power loss

Hose or brush clogged

Everything is elementary here; Disconnect the hose, turn on the vacuum cleaner to full power and watch how it sucks without a hose. If it sucks perfectly, then the sore is the site clogged in a hose or brush. You can try to get to the blockage with a wire or have to disassemble the brush and pipe. It is recommended to clean the brush regularly, after each cleaning, and not when there was a blockage.

Corrugated hose

Over time, on the bend of a corrugated hose, a crack may appear, as a result of which depressurization and poor absorption may appear. Corrugation bursts most often at the junction with a pipe. You can fix it without problems, wrapping it out. It may not be very aesthetic, but quickly, practical and economical. Or cut the corrugation to the wander and insert back into the pipe. Well, who has extra money and time, you can go to the store and buy a new one.

Filters are clogged

Modern vacuum cleaner filters at least 2: fine cleaning before the compressor and graduation. We take out both and turn on the vacuum cleaner. If the craving is excellent, then the problem is in them, you need to clean or replace. Vacuuming without filters, in no case do not try.

Not only does the dust fly into the room, but also in the engine, from which the vacuum cleaner can break.

Wear of the brushes or a break in the heat.subject

If everything is in order with previous possible breakdowns, “and now there,” we are looking for a reason in the engine. The most common reasons are wiped brushes

and a problem with a thermal subject. Brushes cost no more than 100 rubles., Changing them is also not a problem if you know how (I think on the Internet you can find a video on this topic). If such knowledge is absent or there is simply no desire to do this, you have to contact the service center.

Engine breakdown

The vacuum cleaner is buzzing, vibrates, heats up and often turns off, perhaps the problem with the engine itself. In this case, only contacting the service center. At least in order to assess the seriousness of the breakdown. If the matter is in a demolished bearing or turbine clogged with mud, then you should think about repairs. And if they offer a complete replacement of the engine, then it is more advisable to buy a new vacuum cleaner.

The general device of the vacuum cleaner

Regardless of the design and features of the work, vacuum cleaners consist of the following components:

Modern vacuum cleaners are complemented by the waterfilter, due to which the absorption power is also reduced.

The case, in addition to the engine, hides a vacuum compressor, filters and control units. Some models are supplemented by a signaling system and other devices.

Filters clogged

There are two filters in the vacuum cleaner: pre.trial (installed in front of the electric motor) and exhaust (installed after the electric motor). If any of them is clogged, the absorption power falls.

On different models, filters look different and are in different places. Detailed information about them is given in the user’s instructions.

For example, this is what the pre.engineer filter of the vacuum cleaner Samsung SD9480 looks

For example, this is what the exhaust filter of the vacuum cleaner Samsung SD9480 looks like

• Remove the prefabrical filter from the vacuum cleaner and turn it on. Check the force of absorption with your hand. In no case do not vacuum without a filter.
• If the absorption force without a pre.engine filter has increased, clean the filter and install it back. Check the force of absorption again.
  If the absorption force after installing the filter has not changed, then everything is in order with the vacuum cleaner, use further.
• If the absorption force after installing the filter decreased, then the filter has become unusable. Buy a new filter.
• If the absorption force without a pre.trial filter has not changed, remove the exhaust filter from the vacuum cleaner. Check the force of absorption with your hand without two filters. In no case do not vacuum without filters. If the absorption force without filters has increased, clean both filters and install them back. Check the force of absorption again.
  If the absorption force after installing the filters has not changed, then everything is in order with the vacuum cleaner, use further.
• If the absorption force after installing the filters decreased, then the filters have become unusable. Get new filters.

Motor exice

Когда пылесос плохо тянет и начинает сильно «греться» — вероятно, причина в поломке двигателя. Usually, he “warms up” gradually, but in this case this happens immediately after its connection to the outlet. If the device provides a fuse, it will spontaneously turn off when overheating.

The worst sceno of events is a break in the engine stator. If the fuse can be changed, then in the case of a stator break, nothing can be done. The coil winding cannot be restored, so it is better to take care of buying a new vacuum cleaner right away.

In case of malfunctions in the vacuum cleaner, many problems can be eliminated independently, but if the engine has failed, it is better to contact a professional master.

We work with a non.filter

Most vacuum cleaners have a coal cleaner. This was the neighbor. She used the device for six months, and the filter was already clogged.

To begin with, I took out both filters. fine cleaning and negligently. Before cleaning and washing them with water, I gently blew to remove light dust. Then gently knocked out garbage from both parts. The main thing here is a delicate attitude, because in different vacuum cleaners, various materials for components are used and, for example, fragile plastic can crack.

I washed and dried the filter of fine cleaning, shook out Neo and put them back. The situation has improved significantly. the unit began to absorb dust and large garbage.

But I did not fail to warn the neighbor, so as not to delay the installation of new filters, because the situation may soon repeat myself.

I can also give you advice. check not only a vacuum cleaner, but also filters, especially coal. It needs to be changed after every 50 hours of vacuum cleaner operation. Also shake the thin cleaning filter for prevention. This will protect you from unpleasant surprises from technology.

Enlighten with my blog, good luck and good mood!

Thank you for your attention! Until new meetings on my blog. Sincerely, Kuzmin.

The point is in the hat, or rather, in the bag

The most elementary cause of weak traction is also eliminated elementary. the reusable bag is cleaned of garbage, thoroughly shaken, and ideally, washed; one.time package is replaced by a new one and the end is the end.

You can also check the way to check if the dust was spilled out of the overflowed vacuumber inside the unit. If necessary, eliminate this blockage.

It will be easier for you to notice in time that the bag is filled if your equipment is equipped with a special indicator.

The question can be considered exhausted and I move to more significant reasons why the vacuum cleaner does not suck in garbage poorly.