The refrigerator is trying to start but the reason does not start
Refrigeration unit. indispensable equipment without which normal life in a house or apartment is impossible. The failure of this equipment leads to damage to large products and violation of all plans. Therefore, when breaking the unit, you need to quickly respond to the problem. First of all, you need to find out why the refrigerator does not turn on. After that, it will be possible to eliminate the cause of the breakdown and restore the normal operation of the equipment.
As you know, the compressor of the refrigerator is designed for unstable work. It turns on only for a certain time of operation. Turning the device. norm. But how to understand that the device often turns off and requires repair? Most often, an attempt to launch the compressor testifies to the breakdown: the unit emits an unusual buzz, and after a few seconds immediately calms down. To calculate whether the device designed to compress and pump the refrigerant vapor is working normally, you can resort to a mathematical method. If the compressor operation is designed for two minutes, and then the remaining 10 minutes it rests, then the following calculations are made: 2: (210) = 0.166. From the result, it becomes clear that the refrigerator is faulty, since the coefficient during normal operation is 0.2. 0.9.
What to do if the freezer stopped freezing?
If the freezer began to flow, then before calling a specialist, you must make sure that this situation was formed due to equipment breakdown, and not because of inattention during operation. Very often it is improper operation of the equipment that leads to its improper operation. But you should not worry, since the malfunction can be eliminated with your own hands.
First, it is necessary to check the data of the thermostat. It should be in the position between 3 and 4 operating mode, when the products are normally froze, and the motor does not suffer from increased load. In this case, the temperature in the chamber should be in the range of 18-19 ° C. Иногда при помещении продуктов в морозилку человек незаметно выкручивает терморегулятор. If the thermostat is set in the wrong position, you just need to move it to the optimal position. After a while, it is worth checking whether the freezer has begun to work in normal mode.
Secondly, the freezer is poorly freezing due to the intention of ice. Когда образуется большая шуба изо льда, то уплотнитель прилегает неплотно, а значит, в камеру попадает теплый воздух. In this connection, a puddle can form on the floor. To eliminate this trouble, it is necessary to defrost the freezer and carry out thoroughly washing and cleaning the rubber seal.
If during the check you found that the thermostat is in a normal position, and there is no ice fur coat, and the freezer does not freeze, then it’s time to call the Frostrom service center. We carry out high.quality repair of refrigerators at home inexpensively. You can call our master at any convenient time daily from 8.00 to 23.00 hours by phone 8 (495) 745-24-55. Leave a request, and our master will go to you as soon as possible.
The freezer does not freeze in a two.compressor refrigerator
Two.compressor equipment allows you to control the temperature in the cells independently of each other due to individual evaporators and control panels. Therefore, the refrigeration compartment works fine, even when the freezer does not freeze. The problem is noticed by thawing products or a puddle on the floor.
Failure of freezer is always a breakdown? often yes, but there is a situation where the owners “helped” the technique.
What to check yourself
Some models of refrigerators with two compressors provide for disconnecting the freezer compartment. Check if you turned off the freezer accidentally or on purpose, and then forgot to turn it on. If the freezer is disabled, turn it on. Checked, and the camera is enabled? So the reason is malfunction.
Possible breakdowns of two.compressor models
Here are the freezers of the freezer, which our experts eliminate most often when the department does not freeze.
The motor of the freezer
The motor is responsible for the circulation of the refrigerant in the system. The main reasons for the failure of the compressor: due to the overload, windings (launch and/or working) burned or shortened, the engine jammed or damaged wiring, motor contacts. Instead of a faulty engine, a new one is put, the wiring and contacts are restored or changed.
From the experience of the masters!The refrigerator engine often fails due to overload. For example, in the summer, many owners of technology expose the maximum cold on hot days. The motor has been working for too long, overheating and breaks. We recommend not overfilling the refrigerator in such weather, and set the mode a little colder than usual. With such a load, the motor will cope without prejudice to itself.
Frost.tributary
The start.up relay in the refrigerator stands on the motor and performs two functions: it helps it start and protects it from overheating. When the relay fails, the freezer engine does not turn on at all or turns on and immediately turns off. The start.up relay changes to a new.
Thermorerings thermal regulator or sensor of temperature
The compressor is turned on at the signal of the thermostat or temperature sensor. When there is no signal, the engine does not start, and the freezer does not cold. Or inclusions are very rare with lengthy downtime, so the freezer does not freeze, but cools like a refrigerator compartment. Faulty thermostat in electromechanical models or a temperature sensor in electronic control models must be changed to a new.
Freon leak
The refrigerant in the tubes moves through the closed system. Part of the circuit is responsible for heating the refrigerator housing along the perimeter of the freezer door. This is necessary so that the seal remains dry and ensures tightness. A leak in the heating circuit appears due to corrosion of a steel tube. In other places of the freezer contour of two.compressor leaks, there are rarely occurred.
With a leakage of the refrigerant, the freeaget motor-compressor works almost without stops, but due to a lack of freon cannot maintain a given temperature regime in the freezer compartment. When most of the freon evaporates, the freezer compressor stops turning on.
If the leak occurs in the heating circuit, the master cuts it and connects the tubes directly. Then the filter-dryer changes, the tightness of all compounds is tested by crimping. Further, the master vacuum the contour and season it with a refrigerant.
The blockage of the capillary pipeline
The capillary regulates the supply of refrigerant to the evaporator under the desired pressure. The oil from the compressor is burned, and the products of its interaction with the refrigerant are deposited in the capillary tube. The resulting paraffins narrow the lumen, Freon hardly passes through the capillary, so the freezer compartment cools poorly, although the compressor works almost without break.
The blockage in CT is removed with special solutions, blown with nitrogen or poured with oil. Когда капилляр забит в нескольких местах или просвет практически отсутствует, трубка меняется на новую.
Malfunction in the refrigerator door
When closing the refrigerator door, warm air begins to flow into one of the cameras. She heats up. At the same time reacts the temperature sensor, who cools the equipment. This problem can be encountered not only when the door is closed. Rubber seals often wear out, which is easy to replace yourself. To do this, you need to find a suitable seal and carefully fix it in the right place.
Replacing the sealant on the door
TOP-7 reasons: why the freezer does not turn off
In the vast majority of cases, a malfunction, due to which a low.temperature chamber is overly frozen, are hidden in the “depths” of the refrigerator. Find out the reason why the freezer does not stop, is possible only after a full-fledged diagnosis of the repair master. The table contains common breakdowns of the freezer.
| Manifestations of a malfunction | Possible breakdown |
| The compressor electric motor operates non-stop, and in the freezer the temperature does not drop. | It is likely that in the capillary system, blockage has formed and the electric motor is not able to “pump” Freon through the pipeline. Flasons appear due to “burning” mineral oil, which, along with the refrigerant, circulates along the cooling contour. Perform the capillary tube, re.fill with freon and checked the quality of the oil. sometimes it requires replacement. |
| The low.temperature chamber is overly frozen, ice and snow “fur coat” are present on the walls. | There was a breakdown of the temperature regulator (in the case of electromechanical units) or the air sensor of the evaporative element (in refrigerators with an electronic intese). In case of malfunctions of such nodes, the purpose of which are similar, the compressor of the device does not receive a signal that the necessary temperature values have already been achieved. As a result-the electric motor-compressor works non-stop. Carry out the replacement of the broken part. |
| There is a probability that the problem is hidden in the worn.out sealing rubber band. The sash does not completely close and warm air flows enter the freezer. this leads to a “fur coat”. To compensate for excess heat, the unit is functioning non.stop. Perform a replacement of sealing gum. | |
| In a one.compressor unit, a low.temperature compartment freezes excessively, and in the refrigerator there is too warm. | Most likely, the “pitch” of the switching valve. In a normal situation, the valve switches the transfer of the cold between the low.temperature camera and the refrigeration department. so that there are such temperature indicators everywhere that are exhibited. Когда клапан залипает в положении «охлаждение низкотемпературной камеры» – полный объем идет только в морозилку и холодильному отделению ничего не достается. Replace the failed valve. |
| It is likely that the control board was out of order. In this version, the compressor electric motor does not receive the command to switch to the refrigerator compartment. As a result, the low.temperature chamber rewinds, and in the refrigerator. heat. Redesign the control module or perform its replacement. | |
| In a two.compressor unit, a low.temperature camera freezes excessively, and the refrigerator compartment works normally. | It is possible that the problem of the control module is present, which does not give a command to turn off the electric motor-compressor, which cools the low-temperature chamber. Carry out a flashing or complete replacement of the control board. |
| The freezer freezes non.stop, while sometimes temperature values still do not reach these indicators. | Most likely, the system has a refrigerant leak and it is not enough for cooling the chamber to the temperature set. It is possible to determine this when defrosting the refrigerator completely (disconnect for a day from the mains). Когда после этого агрегат (или только низкотемпературная камера) не заработают – 9 из 10 шансов, что проблема в утечке фреона. Calls the master who finds the place of leakage and performs the sealing of the pipeline with subsequent refueling by freon. |
Attention! When a low.temperature camera freezes constantly, this helps to reduce the operational period of the refrigerator. When the work is excessively active, the load on the nodes reaches the limit, which is rapidly depleting the resource of parts.
Malfunctions in units with thawing technology of know.free
It is not difficult to cause a fault of the fault of the NO FROST reckoning system. When the refrigerator in the refrigerator, and ice growths on the rear panel appeared in the low-temperature chamber, defrost the unit (disconnection from the mains for 12-14 hours) and again turn on the refrigerator. When, after such thawing in the refrigerator compartment, the temperature corresponds to the norm, the problem is in violations of the working capacity of the setting system.
With prolonged defrosting, the ice that prevents the passage of cold air flows from the evaporator into the refrigerator compartment, and the cooling is restored. Nevertheless, due to a non-working trim, the effect is temporary and in a week or two this problem will again occur. The table contains signs, possible malfunctions and the option of solving the problem in case of incorrect operation of the technology of shaking the know.frost.
Ice growths in a low.temperature chamber with know.the.free Frost are able to occur not only because of the incorrect functioning of the hollow system. The table shows other causes of ice in the freezer.
| Manifestation | Malfunction | Solution |
| In a low.temperature chamber, ice is formed at the bottom. Sometimes there are traces of fluid on the floor next to the unit. | The channel of the water drain of the low.temperature compartment was clogged. The drainage hole by which the liquid is required to leave after thawing the evaporator was clogged with particles of food or dust. For this reason, she accumulates and intends at the bottom of the freezer | Eliminate the blockage. the drainage canal is washed with the help of sprinting with water at room temperature. Когда жидкость не проходит по дренажу, производят полное размораживание холодильного шкафа (12-24 часа). After that, the manipulation is repeated. When the defrosting did not help and the water does not go through the drainage, the blockage is removed using a cable or cable. |
| No Frost freezing the freezer rewinds, ice is present on the walls inside it. The compressor electric motor turns off less often than before. | The temperature sensor of the freezer. The cooling of the camera is turned off on it. When the temperature sensor is faulty, it turns off the motor-compressor later than necessary, the low-temperature compartment is rewriting. | Fulfill the failed temperature sensor. |
| The sash of a low.temperature chamber does not fit well enough. Inside the compartment is an uneven snowy “fur coat”, a lot of ice near the door. | Damage to the sealing gum or loop loops. Due to the insufficiently tight fit of the sash, warm air enters the department and because of this there is ice. | Restore the tightness of the low.temperature chamber: replace the sealing gum of the new or regulate (put normal) loops. |
| On the rear panel of the low.temperature compartment of the know.toe Frost there is an uneven ice. The unit does not turn off, but the temperature values in both chambers are increased. After defrosting, he ceases to freeze or does not turn on at all. | Refrigerant leak. Due to damage to the cooling pipeline, Freon leaks occurred. To maintain the displayed temperature values, the electric motor-compressor operates non-stop and rarely turns off. | Freon leaks detect and eliminate, seal the pipeline and re.refrigerate the refrigerator with a refrigerant. |
What can be fixed yourself
Before inviting specialists, try solving the problem without repair.
- Make sure that the camera door closes tightly, the panel of the pan or any other protruding item does not interfere with it. Quite often the reason lies in such trifles.
- If you recently rearranged the refrigerator, it could be too close to the heat source. a battery or kitchen slab. Due to the fact that the device is constantly heated on one of the sides, the compressor does not cope with its cooling.
- The compressor can also overload the frost chamber installed at the lowest temperature, especially in the summer. The refrigerator does not cool: the freezer pulls all the resources on itself. Come on, refrain from the constant use of this regime: it is turned on for a short time, with shock freezing of a large volume of products. It is enough to store them.18 ° C.
- Owners of models with the No Frost system should listen: does the characteristic sound of the fan appear from time to time. Sometimes around it forms a layer of ice, which prevents the blades. Without hearing the fan, try to defrost the refrigerator. If the problem has disappeared and did not return within 1-2 weeks-it was not caused by breakdown.
Reasons why the freezer does not freeze
Find out why any technique has broken, usually start with food checking. Sometimes the reason that the refrigerator does not freeze products is a banal damage to the cable or even the absence of electricity on the network or a specific outlet.
But, if the freezer has stopped freezing with a normally functioning refrigeration compartment, the problem is it precisely in it.
Last ice and snow or, conversely, their number of them may turn out to be signs of a compressor breakdown, clogged tubes and even a refrigerant leakage.
The simplest problems of the unit
Among the reasons for the freezers of the freezer, a loose door is often found, due to which air enters the chamber.
The refrigerators of hotpone Ariston may arise after a long work without planned defrosting. Иногда камера бывает слишком сильно набита продуктами, и техника не справляется со своей задачей.
All these issues are solved simply, without demanding the call of the master. In the first case, the problem with a poorly closing door should be solved. In the second. to defrost the equipment, turning it off from the network, in the third. to reduce the degree of filling the camera so that there is free space.
Breakdown in conducting systems
The technique can work incorrectly due to congestion in the capillary system. Nutrients fall into the tubes. sorcini from a worn filter, oil, moisture. Because of this, the cooler in the refrigerators of such a brand as LG does not reach the right place and the products do not freeze.
Congestion do not pass melt water, which accumulates at the bottom of the freezer and flows out. The result is cracked plastic, corrosion of metal elements, due to which the refrigerant flows out.
Problems with automation and electronics
In the freezers of models of any brand, including the Libher technique, there is a temperature sensor responsible for maintaining the desired temperature. If it is broken, the products will be frozen incorrectly.
A sign of the problem-a big break in the compressor due to the data incorrectly transmitted by electronics.
Incorrect frost can be a sign of broken mechanical devices or buttons. The stynol 106 model often has a problem with a timer set in thawing mode. To solve it, there is enough rotation of the regulator by several degrees.
Refrigerant leakage from the system
The freezer of models such as the SFR 167 NF Indesite can work incorrectly due to Freon entering the premises. The reason is microcracks in the tubes due to improper operation or wear.
Cracks often appear if the refrigerator has not been defrosting for a long time, or the user tried to speed up this process independently, knocking out the ice with a solid object.
Malfunction of one of the compressors
In this case, the refrigerator works incorrectly. and the refrigerator continues to function in normal cooling mode. Such a malfunction has to face owners of turquoise models 14 or Atlant.
Sealing rubber band problems
A common failure of the refrigerator is damage to the sealing elastic band, which can be sigred or peel off.
The cause is often a long simple unit. Air enters the chamber, increasing the internal temperature.
Because of this, the compressor of the fridge of the eyelid or any other brand increases power, but does not solve the problem, but only wear out faster.
Mechanical and chemical damage
During operation on the housing of household appliances, mechanical damage appears. from cracks to holes in the rear wall.
The reasons for the appearance are from poor.quality manufacturing materials to improper operation or transportation. Due to damage, air enters, reducing the effectiveness of freezing.
Oxidation and rust on the tubes
Over time, pipelines with refrigerant begin to flow due to corrosion of the walls. Freon goes through the formed holes, and the cold does not enter the chamber.
Urgent adoption of measures to eliminate the problem is required, otherwise it will lead to the failure of the compressor.
Atlant refrigerator does not freeze. what to do?
You need to figure out exactly how the refrigerator does not freeze. If the device consists of two cameras, you need to determine the performance of each.
First of all, if the atlant refrigerator does not freeze, the inclusion indicator does not burn and the compressor does not work, you need to check if there is a voltage in the network. Perhaps the outlet broke down, the contacts were melted in the connection or the wire broke up. But if a light bulb is on in the chamber. there is a food.
You need to make sure that the thermostat is in the working position, not turned off. If the compressor does not work, set the task to the maximum, listen to whether the motor will turn on. Perhaps the compressor will turn on for seconds and stop again with a loud click. Then put a thermostat in position 0. In this case, the relay should click. Quietly. the thermostat failed, the compressor will not start without it. It is required to replace the node.
If the compressor works without stopping, and it becomes warmer in the camera, a refrigerant leak occurred, the motor works idle. You can verify if you touch the capacitor. a lattice on the back side. Without Freon, she will not heat up. This means that the tubes or evaporator have damaged. Often such an incident occurs after defrosting. Atlant’s refrigerator does not freeze, because the ice was cleaned with a hard object, damaged the evaporator pipe.
Help my fridge freezer has stopped working
It happens that the atlant refrigerator does not freeze, and the compressor works, the condenser is warm. The camera quickly overgrows with a snow fur coat and the temperature in it rises. Check, perhaps, sealing rubber has worn out. Sometimes the ice prevents the door to close the door. Fresh air enters constantly, cools, and condensate turns into snow. The cold from the evaporator does not pass through the thick ice. The temperature is gradually growing. You need to eliminate the gap and during the time of defrost the device.
In a chamber with a drip defrust, a drain hole may clog, the water does not leave, ice is formed. Gradually, the temperature in the refrigerator will begin to increase. If the air cooling system of the know.frast is used, the fan can break. At the same time, condensate will freeze on the evaporator, block air labyrinths with ice. Atlant refrigerator will stop working. What to do? Make sure that the fan does not make noise, the ice in the cell and turn off the refrigerator for a hike and drying for at least a day. Then call the master who will install, why the Atlant refrigerator does not freeze, and eliminate the breakdown.
You can not ignore the emergency signal on the control panel. Measures should be taken or specialist. The work of the apparatus with a malfunction will lead to expensive repair.
What else could be
The causes of the malfunction may not be related to the failure of the main details. You can also make the repair of the freezer with mechanical damage with your own hands.
Mechanical and chemical damage
Defects may be found on the case, the appearance of which is the result of impacts or exposure to caustic substances. The presence of a hole contributes to the entry of warm air into the freezer compartment. The compressor works without stopping, but the temperature cannot reach the desired value. Small defects can be eliminated independently. The refrigerator is freed from products and defrost. The damaged area is cut out, after which the insulating material is installed, which is covered with foil.
