Home Article Water does not flow from the coffee maker Polaris
Article

Water does not flow from the coffee maker Polaris

When preparing coffee / water, it flows not from the dispenser, but to the tray

If the finished coffee in automatic coffee machines flows into the compartment for the oxide, then first. It is necessary to inspect the sealing ring / cuff on the upper piston of the tender mechanism. The ring should be elastic and without damage. If the ring on the upper piston scrolls freely and dangles, then it is replaced. If it partially erased from prolonged work, then naturally we change to a new. Dry oak or too soft increased in diameter, too, change.

The second thing that could be is on some machines in the upper counter the piston can appear microcracks, in which case we change both the piston and sealing the piston.

Third. there may be a reason in the sealing of the lower piston, though in this case coffee will merge into the compartment for drops / spent liquid, simply a tray

If in the tender block everything is necessary, then it is necessary to inspect the coffee growing, according to which the coffee is fed to the dispenser, and then in the cup. The silicone tube can burst, and the hard plastic joints of the coffee coat with the tender mechanism are not rarely broken off.

  • Inspect the seal of the upper counter.port and, if necessary, replace it.
  • Inspect the counter.password case for the presence of microcracks, when detected, replace
  • On the upper counterpor, the valve cream is usually installed, it is necessary to inspect its case for the presence of cracks and inspect the seals (usually the valve cream is a spring with a locking element in the form of a fungus, ball or membrane)
  • Carefully inspect the coffee growing to the dispenser. Change damaged elements.

HiBrew compact coffee maker issue fix

Coffee grinder in a coffee machine does not grit coffee

  • If water got into the coffee grinder, it is necessary to disassemble the coffee machine as soon as possible, remove the millstone and manually clean every lamel of the millstone from the adhering wet coffee. There are no other ways of cleaning and removing the millstones. If you do not clean it right away, then the metal millstones will rust and lose the sharpness of sharpening, in coffee grinders with ceramic millstones can rustle the bearing.
  • When using oily coffee (with a characteristic oily brilliance of grain) there will be a similar situation. Fat coffee sticks in the lamella of the millstones, and the coffee grinder will rotate in an empty. We disassemble the coffee machine, remove the millstones and clean the coffee grinder, everything that is wrapped. After assembly, fat coffee is not used. if there is no desire to repeat the procedure for cleaning the coffee grinder.
  • Options are possible when the millstones are very clamped, you can simply increase the grinding and normal work to recover.
  • If the coffee grinder engine does not rotate, then the malfunction in the coffee grinder gearbox. In SAECO / Philips / Gaggia coffee grinders with ceramic millstones. the shaft of the lower millstones may be broken or the teeth of the gear. The reason may be the fact that the millstone has split into the coffee grinder something else except coffee-stone, walnut shell, plastic, screw, etc.P. Maybe the gear can be worn out. The gear, the holder of the millstone and ceramic millstones can be replaced with new ones, the coffee grinder assembled not necessarily changed. In coffee grinders with metal millstones, the failure of the gearbox means replacing the coffee grinder assembly, but if it is Saeco / Gaggia / Philips / Solis / Spidem, you can replace the engine with the gearbox, separately the reducer spare parts, well, perhaps the protective washer of the gear because of which the coffee grinders often fail in which it is. The puck is wiped to holes and through it the coffee enters the gearbox bearing.
  • If the coffee grinder does not rotate, check the engine with a tester. Perhaps the brushes are hidden, which naturally can be changed or faulty of the engine rotor, in which case, change the engine or coffee grinder assembled, depends on the coffee machine model.
  • If the voltage is not supplied to the coffee grinder, then the malfunction will have to be sought in the electronics unit. But before that, you need to check whether the wires that go from the electronics unit to the coffee grinder and are good contacts in the joints.

An error is displayed on the coffee machine display

  • Error number according to the manufacturer’s idea indicates a faulty block. But in fact, this means that the received signal from the sensor of this block issued the result that is considered a malfunction. Although in order to find a malfunction and this information is enough. Suppose the error says that the coffee grinder is faulty, but perhaps there is no voltage supply to the coffee grinder and the malfunction is in the power part of the electronics unit.
  • If there is no display on the coffee machine, then the error can be made by a certain sequence of flashing indicators or cyclic flashing one through a small pause.
  • The numbers of coffee machines of different brands are usually different, which is why it is necessary to find a table of errors of this brand, and even better in the model, but this is not always feasible. As a rule, such information is not distributed by manufacturers for all comers.
  • It is often easier to diagnose than to look for what the error number means. It is only good to imagine at what point this or that block enters the work. I haven’t earned at one time. error. Usually, to determine the malfunction, it takes about 5 minutes, except for the disassembly and assembly of the coffee machine. And you can look for a table day, two and without result.
  • Coffee machine codes table. here

From a coffee maker or through a coffee dispenser is served a drop

  • Too small grinding of coffee, in an automatic coffee machine it is often enough to increase the regulator of the coffee grinder by 1-2 divisions.
  • In the coffee coffee makers is also associated with small grinding, or too large laying and tempting. You can also try. how water goes without coffee if it pours normally. then use coffee of larger grinding, laying coffee on a cup make less.
  • Perhaps the group filter is clogged. clean the coffee group or a welding device from coffee fats.
  • The working part of the pump is possible and it does not create the necessary pressure. Replace the pump.

Spidem trevi automatica coffee machine steamer not working

When working, the tender gearbox creaks, cracks or does not act

What should be the temperature of the drink

The canonical espresso is preparing a machine gun on water, the temperature of which is at least 90 degrees. That is how the drink will receive the whole taste and aroma, taking it from the ground grain. If you drink not such hot coffee as you would like, the reason can lie in trifles, for example, in the use of cold utensils. Before preparing the drink, it is better to warm the cup, at least under a stream of hot water.

The second point is the wrong equipment settings.

To check this, we do the following:

  • We go to the menu;
  • we find the “temperature parameters”;
  • We set the value to the maximum (we turn the rotary steeple or use repeated pressing the corresponding button).

The third “trifle”. the state of the tender device affects the temperature. If it is not warmed up, the coffee will turn out not so hot. If you just turned on the device, heat the system by driving a portion of the drink.

Why the water does not heat up in the coffee machine

I will give several of the most common and less popular reasons why the technique refuses to heat water.

If a cold drink enters the dishes, the source may be like this:

  • Damage to the heating element. He can burn out corny or break due to the fact that his resource has been released. A break in the heating chain may occur;
  • Sensor breakdowns. the device in this case cannot determine the temperature of the liquid, the command for turning on the heater does not arrive. As a rule, a thermostat is required;
  • broken by the corballock;
  • Problems with an electronic control unit. In this case, the coffee machine cooks cold coffee or does not heat water at all. The reason is the breakdown of the controller. it is this thing that triggers the work of the hets and heated the unit itself. Most often it is enough to replace the controller with a new.

Problems with a heating unit, boiler, Ten

Boiler. an important node of any coffee apparatus. It is inside this metal element that the heating of the fluid is realized, on which coffee is subsequently prepared. So that the taste of the drink always remains at a high level, the correct settings of the coffee machine and timely decalcination are needed.

With this breakdown, the drink has too low temperature and a weaker taste. The cooking cycle itself takes more time than usual. The source of most problems with heating elements is scale.

Deposits are laid on the walls with a thick layer, corroding them. The taste of coffee will gradually fall, after which a complete breakdown will occur. Another reason may be the night that the device will spend at low temperatures or the oxidation of contacts of the boiler electrical circuit.

To extend the life of the device, it is recommended to use preventive measures:

  • The use of filtered water is on an ongoing basis;
  • Decalcination-1-2 times a year, which depends on the recommendations of a particular manufacturer.

Solution: Ten change. If you need to replace the tank for heating the liquid, first you should get access to it, for which the equipment is partially disassembled, the connections are unscrewed, the tubes are removed, etc. After the repair, all the details are placed in place in compliance with the correct sequence. In general, this repair should be entrusted to specialists.

Some coffee machines are equipped with SMART beiler, which are able to level the temperature, pressure, water level at the slightest deviation from the given parameters. The repair of such systems is carried out only in service centers.

If the thermostat flew

On this issue it makes sense to dwell in more detail. The heater thermostat automatically regulates the heating of the boiler, controls the heating limit, in t.h. Minimum heating. Formally you can call this thing a conditional fuse.

If a thermostat flew in a coffee machine, it will never heat up water. This is the second most popular breakdown after the hets. To determine the operability of the node, it is worth checking its resistance. If it is not, you can safely carry the equipment to the service, although those who are familiar with the electrician are able to replace their own.

water, does, flow, coffee, maker, polaris

This is schematically done as follows:

  • The device is de.energized;
  • A tap with cold water is overlapped (if the machine operates on a water supply);
  • All existing liquid merges;
  • The protective casing is removed, the fasteners are unscrewed;
  • The flange and clamping ring of Ten are dismantled;
  • The temperature regulator sensor is disconnected, which regulates the relay;
  • A new thermostat, clamping ring, casing are installed on the boiler.

It is advisable to photograph each step of the analysis process in order to comply with the correct sequence when assembling.

Paroblock breakdowns

If you like mouth-watering dairy-coffee delicacies, cappuccino with a foam, a device like a corblock should always be in perfect condition.

In the opposite case, the breakdown will inevitably lead to a decline in temperature, about the preparation of cappuccino and some types of coffee will have to be forgotten.

If the machine is not able to give steam and stops its production, the reasons are as follows:

Solution: Installing new sealed rings in return for worn out, which is better to do in the service center, a complete replacement of the node, sensors. To do this, the device will be dismantled, the old Parbllock will be removed, new will be put and collect again.

Some sources of breakdown can be eliminated independently. The user can carefully clean the hole through which steam is supplied.

How to disassemble the Polaris PCM 1516e coffee maker without breaking it to the end

Hi all! A small incident in the kitchen has occurred today. When making coffee (more precisely foam for cappuccino), the miracle coffee maker Polaris 1516 sneezed loudly from all its cracks pouring water. Later it turned out that inside the coffee maker, a steam supply pipe into the cupboard of the cappuccinator and all this airborne mixture went to scream the insides. The coffee maker stopped showing signs of life, it was decided to disassemble it for revision and drying. What if he earned?

water, does, flow, coffee, maker, polaris

Armed with a set of screwdrivers, began to disassemble the coffee maker. I twisted it for a long time before it was possible to disassemble it. The main problem is two lateral decorative pads that give a solid look and monolithic coffee maker.

Before starting an independent disassembly of a coffee maker, pay attention to the drawing below. It shows the mounting points of the lining. Red arrows. screws, green. latches. Before clicking the latches, we need to unscrew 5 screws for each lining, only 10 screws.

So, let’s go!one. Remove the container with water, the droplet collector, turn off the coffee maker from the network.2. Turn the coffee maker up upside down, unscrew and remove the bottom.

To remove the buttons panel, unscrew 3 screws under the red arrows and move the panel down, then pull it out without effort

Put the coffee maker on the side and unscrew 4 screws of the side lining mount. 2 at the top, where the buttons and 2 block are below, where the drip tray.

We do the same on the opposite side.6. We turn the coffee maker and unscrew 2 more screws from the bottom.7. With your fingers or a liner, we eliminate the latches of the linings outward.

Unscrew the screws (red arrows) from the bottom of the bottom and squeeze out the latches (yellow arrows)

The pads should be a little free, but they will still hold the remaining latches from above and behind.9. Using a plastic card, pry the panel in the upper part and try it with a slight effort to remove it.

We do the same with the opposite lining.

Now we see that this coffee maker is not made of a monolithic piece of plastic, consists of two parts. To divide them, you need to unscrew 4 screws that hold the upper part.

The first 2 screws are found under the buttons block, and the latter is from the bottom.

Collect in the reverse order.I hope someone will help someone.P.S. The coffee maker after drying earned.

Coffee flows from one spout of coffee / dispenser

The most ordinary and standard reasons. The second point is most often.

If something gets into the dispenser or the flakes of old dried coffee come out of it with coffee, then you can’t do without removing the dispenser. It needs to be removed and washed well with your hands and brush. No pills in this case will help as they say. It’s too late to drink Borjomi no once, nor two, nor five in a row.

With chemical agents, such pollution can no longer be cleaned, and the worst thing is that if you try to clean it with coffee fats and deposits cleaning, then something will certainly leave the dispenser, but most of the dispenser sticking to the walls will remain in place, and plus everything will be plus. This raid is saturated with chemistry and for a long time when preparing coffee, the drink will smell like a cleaner.

Therefore, we remove the dispenser, analyze it if it is collapsible, we cut it if it is not analyzed and clean it, then we collect everything back. Inexperienced dispensers can also be replaced with a new.

In order not to form a raid on the dispenser, it is necessary to regularly conduct an automatic cleaning program from coffee coating and deposits. Then the dispenser will not get clogged.

Coffee grinder in a coffee machine does not grit coffee

  • If water got into the coffee grinder, it is necessary to disassemble the coffee machine as soon as possible, remove the millstone and manually clean every lamel of the millstone from the adhering wet coffee. There are no other ways of cleaning and removing the millstones. If you do not clean it right away, then the metal millstones will rust and lose the sharpness of sharpening, in coffee grinders with ceramic millstones can rustle the bearing.
  • When using oily coffee (with a characteristic oily brilliance of grain) there will be a similar situation. Fat coffee sticks in the lamella of the millstones, and the coffee grinder will rotate in an empty. We disassemble the coffee machine, remove the millstones and clean the coffee grinder, everything that is wrapped. After assembly, fat coffee is not used. if there is no desire to repeat the procedure for cleaning the coffee grinder.
  • Options are possible when the millstones are very clamped, you can simply increase the grinding and normal work to recover.
  • If the coffee grinder engine does not rotate, then the malfunction in the coffee grinder gearbox. In SAECO / Philips / Gaggia coffee grinders with ceramic millstones. the shaft of the lower millstones may be broken or the teeth of the gear. The reason may be the fact that the millstone has split into the coffee grinder something else except coffee-stone, walnut shell, plastic, screw, etc.P. Maybe the gear can be worn out. The gear, the holder of the millstone and ceramic millstones can be replaced with new ones, the coffee grinder assembled not necessarily changed. In coffee grinders with metal millstones, the failure of the gearbox means replacing the coffee grinder assembly, but if it is Saeco / Gaggia / Philips / Solis / Spidem, you can replace the engine with the gearbox, separately the reducer spare parts, well, perhaps the protective washer of the gear because of which the coffee grinders often fail in which it is. The puck is wiped to holes and through it the coffee enters the gearbox bearing.
  • If the coffee grinder does not rotate, check the engine with a tester. Perhaps the brushes are hidden, which naturally can be changed or faulty of the engine rotor, in which case, change the engine or coffee grinder assembled, depends on the coffee machine model.
  • If the voltage is not supplied to the coffee grinder, then the malfunction will have to be sought in the electronics unit. But before that, you need to check whether the wires that go from the electronics unit to the coffee grinder and are good contacts in the joints.

An error is displayed on the coffee machine display

  • Error number according to the manufacturer’s idea indicates a faulty block. But in fact, this means that the received signal from the sensor of this block issued the result that is considered a malfunction. Although in order to find a malfunction and this information is enough. Suppose the error says that the coffee grinder is faulty, but perhaps there is no voltage supply to the coffee grinder and the malfunction is in the power part of the electronics unit.
  • If there is no display on the coffee machine, then the error can be made by a certain sequence of flashing indicators or cyclic flashing one through a small pause.
  • The numbers of coffee machines of different brands are usually different, which is why it is necessary to find a table of errors of this brand, and even better in the model, but this is not always feasible. As a rule, such information is not distributed by manufacturers for all comers.
  • It is often easier to diagnose than to look for what the error number means. It is only good to imagine at what point this or that block enters the work. I haven’t earned at one time. error. Usually, to determine the malfunction, it takes about 5 minutes, except for the disassembly and assembly of the coffee machine. And you can look for a table day, two and without result.
  • Coffee machine codes table. here

From a coffee maker or through a coffee dispenser is served a drop

  • Too small grinding of coffee, in an automatic coffee machine it is often enough to increase the regulator of the coffee grinder by 1-2 divisions.
  • In the coffee coffee makers is also associated with small grinding, or too large laying and tempting. You can also try. how water goes without coffee if it pours normally. then use coffee of larger grinding, laying coffee on a cup make less.
  • Perhaps the group filter is clogged. clean the coffee group or a welding device from coffee fats.
  • The working part of the pump is possible and it does not create the necessary pressure. Replace the pump.

When working, the tender gearbox creaks, cracks or does not act

Espresso Polaris PCM 1517ae Coffee machine. review

I wrote a review for a very long time. I didn’t want to write \ Send a review for this coffee maker. But there are such not literate, out of ignorance, reviews on it. that you want to rehabilitate it.

And this is despite my sad review with her, long disputes, calls to a hot fishing line for a trimmer.And the service center. But all this is not treated with coffee makers, but to the negligence of people selling it. And in particular the famous for him.

But still, the review will be about the POLARIS PCM 1517AE coffee maker, and not about the negligence of people.

POLARIS PCM 1517ae Coffee machine

This coffee maker is intended for domestic use, it is not large, light, consist of metal and plastic. Of course, for commercial purposes, it will not go to use it.

I highlighted some indicators that must be taken into account by choosing home a coffee maker (not a coffee machine, but an open coffee maker).

  • Used coffee: ground;
  • Maximum pressure: 15 bar;
  • Horn material: metal;
  • Power: 1050 W;
  • Water tank volume: 1.3 l;
  • Type: espresso;
  • The possibility of cooking cappuccino: eat, manual cooking;
  • Simultaneous preparation of two cups: eat;

a horn with one two.bottom filter for 1 or 2 cups.

For especially “sorting coffee connoisseurs”, I allocated an important point that we need below it will be easier to understand the principle of coffee makers.

When choosing a coffee maker, it was important for me. pressure, the presence of the capricum and water tank.

  • Pressure 15 bar pump, this is excellent! Such pressure is in professional coffee machines, it will let you cook coffee right correctly!
  • Volume.Well, here it’s clear, I just looked into the future and that and did not want to add water every 2 espresso circles. For example, in coffee makers where the volume is 500-700ml.
  • Cappuccino, for the opportunity to prepare cappuccino and latte.

How coffee makers do they do?

A two.day filter with the lower bottom, in which one small hole, such a horn will provide not even an experienced “barista” foam cream, despite the grinding and incorrect tamping of the tablet.

Very comfortable cover, just raise and turn to the side, then pouring water will not be problems. There are marks of maximum and minimum.

I pour water from the filter to avoid poor.quality impurities and early scale.

A pallet with a mesh lid, collects drops, and a leak from a mug! if they had not turned off the coffee maker in time.

In addition, if you have a high mug, so that it fit, just remove the pallet and put the mug.

But the espresso coffee machine is designed according to the portion of espresso, and the espresso mug climbs!

At the top there is a place where you can put the mugs, but I leave a horn and a measured spoon there there.

Measured spoon: on the one hand, a spoon, this amount of ground coffee must be added into the filter (below) and tamped with the other side.

How to use, how to cook coffee?

First we turn on the indicator and it lights up red. The lower indicator must be in the position of the mug!

After it lights up green, coffee can be cooked!

To do this, turn the arrow to the left, to the position of the mug. When the coffee is enough to turn the arrow back to the central position.

If you need to beat milk:

Switch the button towards the pair icon and again wait until the indicator lights up green.

Then we turn the arrow into the right, to the Paul position. And steam from the cappuccinator whips milk.

The connection of the contents of the mugs and the drink is ready!

ATTENTION! Kapuchino, t.e. You can beat milk only after cooked coffee, and not before! Otherwise, the pressure of 15 bar will pass water through the horn.

If you beat milk, to coffee, turn off the coffee maker and let it cool!

In other things, even a coffee maker speaks about this! Apparently our people do not read the instructions well.

I myself began to cook coffee after a couple immediately, and even the horn pushed poorly, and the horn was knocked out by pressure, it broke the mug. And all the coffee from the horn was all over the kitchen!

If there is no pressure in the coffee machine

The essence of the problem may lie everywhere, including in factory marriage. But, do not flog a fever. initially it is better to check whether heating works, the serviceability of emergency and air valves, adjustment of the pressure sensor, the work of the pressure gauge. However, most often the source is a malfunction of the pump.

Damage of the pump

The pump is the most important node of any coffee machine, regardless of its type and brand. This thing creates the required water pressure, which is supplied to the compressed coffee tablet. If it breaks, you will not drink the coffee.

As a rule, all machines are equipped with similar pumps, their own brands are much less common-basically, this is the priority of premium apparatus. But, this does not reduce the likelihood of malfunctions, but it may complicate the repair.

Often the pumps begin to let in water inho.nuclear, when the espresso was boiled, the liquid barely oozes into the glass. The reason for this lies in the breakdown of the spring and clogging. The node should be cleaned, the system is launched with a good pill, respectively, the spring needs to be replaced.

Signs of the failure of the pump are as follows:

  • complete lack of flow flow;
  • weak pressure of coffee;
  • Significant deterioration in the quality of coffee, a complete absence of cream foam is found. The drink becomes bad if the pressure is below 9 bar.

I note that all this often occurs in capsule.type coffee machines, such is the statistics. It is easy to detect the malfunction yourself. you should just start the coffee cooking process and follow the intensity of its submission.

Solution: We clean, decalcination. If it does not help, we carry the device to the service center. Diagnosis is required.

Filter filter

The second aspect affecting the lack of pressure is problems with filters. If you neglected regular cleaning, used poor.quality grain or capsules, this will happen quickly. When blocking, the system will stop missing a sufficient amount of drink.

Solution: To eliminate the breakdown, it is enough to rinse the filter under a stream of running water.

You can use special cleaning products. One should adequately evaluate their own forces. the slightest scratches will provoke a delay in coffee beans. In view of this coffee machine will be clogged much more often.

Too small grinding grains

If the device does not pour coffee well and at the same time makes extraneous sounds, this also indicates a filter clogging. The main problem is the use of too small grinding. Therefore, the first step should be checked precisely these settings. In general, I note that in any coffee machine you should not use too small grinding and old, over.legged grains, more like crackers. This will save from a lot of problems.

Solution: correctly adjusting the grinding on a coffee grinder.

The appearance of an air cork

Another reason for the lack of pressure in the coffee machine is the formation of an air cork. Solving one solution: you should drive hot water through the cappuccino. If the malfunction remains, it is worth cleaning the system.

Improper pressure sensor adjustment

Switches maintain pressure in the boiler using resistance coils. Factory settings are such that the machine is calibrated by 1.1-1.3 bar (different manufacturers can be different. up to 1.5 bar). If you should change the factory pressure to the worker, this is done using the adjustment screw. Full revolution of the screw for or counterclockwise corresponds to 0.1 atm. Actual pressure is monitored on the pressure gauge.

To control calibration, several portions of coffee should be prepared.

The refusal of the manometer

In modern coffee machines, two pressure gauges are installed. pumps and boiler. They can be placed in one block or separately. The boiler manometer controls the temperature and pressure, it announces that the device has reached the working condition. all the same 1.1-1.5 atm. If there is one pressure gauge in the car. this thing works for a boiler.

The pump manometer controls the pressure in the hob. Working parameters in this case correspond to 9 atm. Deviations from the norm indicate a breakdown.

Solution: replacing the node or tubes in the service center, decalcination.

The device of the coffee maker

For the first time they prepared coffee, letting hot water through the grinded powder, 220 years ago in 1800. Since then, devices of devices have constantly changed, but the very principle of obtaining a drink remains unchanged.

The modern device for cooking drip type coffee consists of several parts:

  • non.removable water container located behind the device;
  • tank for heating water;
  • heating element. heating element;
  • containers for a shift filter;
  • Foils with a lid for a finished drink.

The principle of operation is unchanged for two centuries. Water enters the boiler, heats up to 95-98 ° C, rises up the pipes. Condensed, it passes through a wrapped coffee powder. The finished drink flows through the filter and enters the container.

Gushch with hard particles of coffee remains in the filter, a clean drink falls into the container. The device is equipped with a heating device of the finished drink. Drip devices have a different shape, design, electronic or manual control, additional functions.

Grain for cooking is taken strong or medium frying. A drip type device prepares only one type of drink. natural black coffee, called “Americano”. The device will not be able to prepare “espresso” or “cappuccino”.

Some coffee makers have a function of changing the fortress of the drink by reducing or increasing the power of the device. With more intense boiling, the steam condenses stronger, the flow of drops passes through ground grains of coffee faster and does not have time to saturate the drink with a strength.

A cleaning cartridge can be arranged in the water tank. This shift element cleanses the liquid from chlorine and salts. Its use prevents the formation of scale, accumulating on the inner surface of the elements of the coffee maker.

Manufacturers install a timer on coffee makers, which allows you to set the time for turning on, equip the devices with a device for programming the cooking modes.

The causes of the coffee maker malfunction

The device of the drip type device is simple, the device consists of several components. If a drip coffee maker stopped working, the cause of the malfunction may be a factory defect or failure of individual elements during operation.

The coffee maker does not turn on

If the coffee maker does not turn on when the button is pressed, the reasons may be as follows:

  • There is no electricity online. It is necessary to check the availability of power in the outlet by connecting other devices to it.
  • Damage to the fork or cord coffee makeup cord.
  • Cliff or disconnection of the wires inside the device.
  • Damage to the thermostat.
  • The fuse has burned out.
  • Failure of heating element.
  • The power button was out of order.

If the coffee maker does not turn on, before searching for the malfunction, it is necessary to disconnect it from the network and free the tank from the water. You also need to remove the filter with ground coffee powder.

Water leak

If a leak forms when filling the tank for cold water, the cause may be:

To determine the type of malfunction, it is necessary to remove the fork out of the outlet without pouring water, remove the lower lid. In the footsteps of the leak, you can find a knot that failed.

The buttons do not work on the panel

The buttons on the lower panel can fail.

Buttons may not respond to pressing due to lack of power supply. You need to check the connection of the coffee maker to the network.

Water does not heat up

The causes of this malfunction can be in the failed heating element or thermostat. It is necessary to de.energize the device, pour water. Then remove the lower cover and check the device with a multimeter.

Coffee is weak

This is not a breakdown of coffee makers. The cause of the weak taste of the drink may be incorrect proportions of water and a grinded powder. It is also necessary to check the shift filter. If it is installed incorrectly, the edges will bend, and hot water will pass by.

The leak of the finished coffee

The coffee makers are equipped with a valve installed at the bottom of the filter container. This device prevents the course of coffee on the heating plate with a cleaned flask. A leak of the finished drink may appear.

  • The valve is not designed for a large pressure of the finished drink. If you do not put the flask in place, leaks are inevitable.
  • Coffee drips directly into the center of a small hole in the lid of the jug. An incorrectly installed flask may cause a leakage of the finished drink.
  • Valve malfunction.

From a faulty valve will constantly drip liquid onto the heating plate. This may indicate the smell of burnt coffee.

Long preparation of coffee

In the process of work, the pipe coffee makers are clogged with scale deposits. The water duct decreases sharply. Steam rises in a small amount insufficient for normal condensation. Drops are rare, water manages to cool. It is necessary to rinse the device with a solution that removes the scale.

Damage to the hydraulic system and boiler

These are cases when the intervention of a non.specialist can lead to an aggravation of the situation. Often breakdown occurs due to accumulation of lime and coffee oils against the background of irregular cleaning. Therefore, the only thing the user can do on his own is to clean (decalcination and removal of oils) using special tools, following the instructions in the instructions.

It is easier to perform this procedure on devices where automatic cleaning is provided. The main thing is not to save on reagents, since the final result often depends on their quality.

If the purification has not changed the situation, it is better to seek help from specialists. for example, in Taber’s company Service. Site: https: // Tabera.ru/remont-kofemashin/. Using special equipment and tools, they will reveal the cause of the breakdown and eliminate it in a short time, possibly at the location of the apparatus.

Rupture of hoses, tubes and sealing rings

Another consequence of the irregular cleansing of the unit of salts and coffee oils. Deposited on the surface of flexible elements, they react with the material from which these elements are made. Over time, microcracks form in the places of the most violent response, and then the gaps.

The sealing rings, adapters, silicone tubes, gaskets and seals are most often damaged under the influence of scale. To detect a defect, you must carefully open the body of the device disconnected from the network and carefully inspect its insides. As a rule, at the place of damage to the part on the walls there is a deposition of condensate, the damaged area itself does not look like the rest of the part fragments.

To make sure that the source of leak is hiding here, you can carefully separate the suspicious element and fill it out with water. After some time, she will begin to flow out of the gap site.

As a rule, sealing rings and tubes are sold in the departments of spare parts for coffee machines. But if for some reason replacing them causes difficulties, it is better not to take risks and contact the service center. Incorrect installation of the part is fraught with moisture from a coffee machine, and this, in turn, can lead to wet and failure of expensive nodes.

Another reason is a crowded tray

The pallet is often filled while making coffee or after cleaning the system from scale.

To exclude such problems, it follows:

  • Check that a coffee machine is on a flat surface. In the opposite case, the pallet filling indicator can work incorrectly;
  • Before starting the device, make sure that the indicator responsible for filling the pallet does not burn. If it turned on, the excess fluid should be drained;
  • Clean the pan for drops of water before cleaning the machine from scale.

Water tank breakdown

To understand that the cause of the leak is a damaged tank, pour a liquid into it and wipe the outer surface dry. The container is best placed on a dry cloth. Further, the whole thing is left for an hour. If the napkin is wet, the container changes to a new.

Here, perhaps, is all that can be said about the causes of leaks. I advise you to initially be attentive to technology in order to avoid all kinds of problems. The rest is the service center to help you. Independent repair often leads to more deplorable results.

Author

Goltilar

| Denial of responsibility | Contacts |RSS