Filter clogging prevention and washing machine diagnosis
No one can protect against natural breakdowns of washing machines, but even the most expensive equipment needs proper care and use. The following simple rules will significantly prolong the life of your washing machine components:
- When loading things into the washing machine, you must not exceed the allowable weight of the laundry;
- Before loading, you need to inspect all s and lapels of the clothes, there may be small parts or debris;
- If your house has power surges, you need to install a stabilizer;
- At least once every 5-6 months to clean the filter.

Efficiency and quality of washing depend on regular preventive measures
Monitoring the working condition of the pump
After completing the previous points of the recommendations, it is important to constantly monitor the drain pump. It is necessary to connect the automatic machine to the power supply, selecting the option “drain“, and in its absence “wring”. In this situation the pump starts to rotate which can be seen in the hole for the filter. It is necessary to pay attention to how the impeller rotates. If it does not rotate, then you need to replace the pump. The first steps for its replacement coincide with the procedure of cleaning from clogging the pipe that connects the tank to the pump, but without disconnecting the pipe from the “snail”. The washing machine must be tilted on the back wall, disconnect the volute, and then disconnect the pump from the supply system and from the volute itself. In most of the new generation washing machines are equipped with drain pumps of the common types and models that are on sale.
One more nuance should be noted. There are cases when everything is fine, but the washing machine does not drain the water. Removed the filter, checked the spigot and drain hose, no clogs, the pump set to “drain” program, rotates.
There are two reasons why the washing machine stopped draining water: the first. there was a clogging of the hose for drainage and requires its cleaning, the second. the pump has exhausted its resource and rotates only on “dry”. That is, it can work without water, but with water. it jams and does not have enough power. Therefore, such a pump must be replaced.
See also. How to reset your washing machine yourself
The washing machine does not drain.
During the washing of laundry it was found that the machine has stopped draining water. Such a breakdown is one of the most common. Depending on the manifestation of the fault, determine the cause. So, we see that:
- water drains extremely slowly, the washing program fails in parallel;
- during washing the program is interrupted at the point where the water should be drained;
- with one program water is drained, with the second. not;
- The water is emptied during the main wash but not during the rinse;
- Spin mode is blocked after emptying the water.
There may be several reasons for this malfunction:
- The connection pipe is clogged with debris;
- A foreign object has entered the pump;
- The pump filter is clogged with garbage;
- The pump is broken;
- The siphon or drain is clogged;
- The hose used to empty the water is clogged.
If the machine stops working during the intermediate or final spin, unplug it and then restart the program. If the situation does not change. use the buttons to turn on the rinse and spin. Pump the water out of the dispenser and call for service. Program and modular breakdowns cannot be repaired independently.
Fixing the washing machine by yourself
How to fix a washing machine that won’t drain
Before any repair work, be sure to disconnect the machine from the mains by pulling the plug from the socket. Never disregard the safety rules!
Such manipulations as washing machine motor repair, replacement of the washing machine motor, repair of other parts and components must be performed only when the machine is de-energized.
The filter is located in the lower part of the body of the machine from the front side. Put a cloth under it in advance, or better yet, prepare a container, as water may leak out in the process. If the filter is clogged. clean it of debris and foreign objects. In some cases problems with the drain can be corrected this way.
Clean the socket that connects the pump and the tank of the washing machine
To gain access to it, you need to unscrew the screws that fix the fixation of the drain, then. remove the socket, remove the fixing clamp and drain the water into a prepared container.
By pressing in several places, determine the presence of foreign objects (debris) in the spigot. If there are any, remove them. Assemble the construction in its original state.
Check the pump impeller
It is located immediately behind the filter. If even a small foreign object got into it, the impeller will not work. Rotate the impeller and if it rotates freely and no debris can be seen, then it is OK. If you found a button, coin. remove it immediately. If this didn’t help your machine either. check the pump (drain pump).
To check the function of the pump, remove the filter as described above. Set the program of the machine to spin and shine the light on the filter hole. If the drain pump impeller does not move, then the pump itself is broken. Proceed to replace the filter.
Initially buy the necessary original spare part according to the model of your washing machine. If it is not available in nearby stores. use the Internet search and buy the necessary part in the online store.
To replace the old part with a new one, remove the washing machine’s drain assembly. Disconnect the drain pump (pump) from it, then slowly and carefully remove the wires from it. Take a new drain pump and install it in place of the old one. Attach the wires and other parts. Reassemble the appliance to its original condition.
Reassembling the washing machine
During reassembly, carefully check the fastening points. Make sure all the clamps are in place, check their tightness, tighten the screws and check that all parts are in place.
After all the manipulation perform a test wash. While washing, carefully check the appliance for leaks. If it is there. in some place the connection has not been securely fastened. Eliminate the defects and check the washing machine again.
Causes of difficulty draining
If the water from the drum does not drain completely, it means that there is something in the way. The main cause should be sought in the drainage system: clogging in the drainage filter, drain pump breakdown, clogging nipple between the tank and the pump.
Other reasons why the automatic machine takes a long time to drain can include:
- Breakdown of control unit components.
- The drain hose was installed with violations, the drum is not completely free of water, the spin does not start.
- Sewer blockage.
To accurately determine the reason why the machine does not drain to the end, requires professional diagnostics.
Top-Load Washer Won’t Drain — Washing Machine Troubleshooting
Clogged filter
If the filter is heavily clogged, the water from the tank takes a long time to drain. It is necessary to thoroughly check the element, because even a small clog will slow down the process of draining. To clean the drain filter, you need to open the decorative door on the bottom, right side of the front housing, unscrew the filter, rinse under running water, free the dirt from the seat for the filter, install the element in place.
If the filter is not removable, welded due to intermittent use at high temperatures. Master call is required to disassemble the washing machine and replace the element.
Drain pump clogging
Drainage is almost non-existent or very difficult if the drain pump is faulty. The spin mode also does not turn on. The pump in different models of washing machines is located in different places. To remove the pump from Bosch brand washing machines, unscrew the front of the housing. Electrolux machines have a rear-mounted drain pump.
To restore the drain pump, you must first clean the impeller from dirt and check the rotation of the part. Remove other debris if the rotation is difficult. The impeller is not suspicious, so only a specialist will be able to detect a malfunction.
How To Repair Top Load Washing Machine Drain Problems At Home On Your Own Like A Professional
Electronics are out of order
What to do if the appliance is not draining properly? Need to check the electronic components of the washing machine. First of all, the problem is caused by components of the control unit: the stabilizer, which stops giving commands to other nodes of the machine. The problem is common among Zanussi, Beko and other brands. At the first sign of malfunction you should call a professional master. Your own actions while repairing the appliance can cause a complete breakdown of the appliance.
Why there is no water drain?
Drainage of dirty water after the main wash or rinse is as follows: water from the drum through the outlet nozzle under the action of the outlet pump impeller goes into the outlet filter (a detail needed to prevent the ingress of large fragments in the hose appeared during the washing. detached buttons, coins from s). Water passes through the filter and flows through the drain hose to the sewer. Drain pump is controlled by an electronic circuit board.
Pump works, water does not drain | The pump works intermittently | Pump does not work, water does not drain |
Plugged tank nozzle Plugged drain hose Plugged filter Broken pump impeller | Program failure in the circuit board Bad contact between the wires from the circuit board and the pump | Pump motor defective Pump power wires damaged |
Thus, the water may not drain for reasons of malfunction of different elements:
- Drain hose;
- Exhaust filter:
- the impeller of the pump;
- pump motor is damaged;
- the outlet nozzle.
- electronic circuit board.
The causes of failure can manifest themselves in different ways, for example:
- Drainage stage is slower than usual, washing program failure may occur;
- the program stops executing at the moment of draining;
- The malfunction occurs periodically. with some washes safely completed;
- Water does not drain when the pump is running.
The washer does not spin or drain even after removing the drain filter? So the problem is in the pipe that connects the drum to the pump. You will need to disassemble the appliance to remove the drain pump and with it the entire assembly involved in draining. Further it is required to disconnect a branch from the pump and clean it from clogging, to pour out the remained water in specially prepared container. Then we put everything back in place.
The washing machine does not empty the water. what to do?
What to do if the washing machine after washing does not drain the water and does not let open the hatch? In our practice, this is a very frequent problem with which we are addressed by clients. often the repair of this malfunction costs about 3 thousand without taking into account the cost of parts. But is it necessary to call a master?? Is it possible to fix the problem on your own??
Usually, at the end of the washing program water is pumped out and drained into the sewer. However, it may happen that the water does not drain, the laundry does not spin, and this can be caused by several reasons, which we will talk about in this article. Some causes you can fix yourself.
First you need to turn off the machine, unplug it and open the filter cover (located at the bottom right). To prevent the floor from getting wet, you can use a rag and a scoop or a low basin, there will be a lot of water!
Causes of failure and how to find them
If the washing machine does not drain the water, then the causes of such a breakdown can be very different. Let’s list them in order of likelihood of occurrence:
- The drain hose from the machine to the sewer is clogged. If this chain also includes a siphon, it can also be clogged with garbage.
- Clogging of the filter. Overlap the filter can coins, stones, paper, buttons and other objects that are not put out of the s in time.
- The drain pipe which is located between the washer-dryer tank and its pump is clogged with something.
Many modern machines have digital displays which show not only the operating modes but also the error codes. On these codes, using a special table in the manual, you can determine the nature of the fault for more accurate diagnosis.
Some programs installed in the washers can not provide a spin mode, so the machine is waiting for more commands, making a pause in the washing process. Therefore, if the washing machine does not drain the water and does not spin, then you need to make sure that the required mode of operation is set on the machine.
Important: If the washer draws water and immediately drains it, the causes may be a failed water level switch, a faulty inlet valve, or a problem with the electronic module. In the latter case, you are unlikely to be able to fix the problem yourself.
How to prevent clogging of the filter: the recommendations of the editors
As you can see, the rules are not complicated, and it is quite easy to follow them.