Washing machine Haier error Lock How to fix

Typical malfunctions SM Hayer

In the table, we examined errors and their value. We will analyze how to carry out independent repair of the washing machine Hayer.

The door does not close

You are trying to launch the wash, but nothing happens. Check the hatch door, press it denser. Perhaps between the door and the hatch stuck underwear.

If after checking you cannot close the door, do the following:

• Check the handle for serviceability.
• Inspect the Language tongue. It happens that it shifts from a place, then you need to return it to its original position.
• Inspect the side loops. If they weakened, and the door sagged, tighten the mounts.
• Check UBB. Electronic Castle. It can be tested by a multimeter for serviceability. If the device is faulty, you should replace it with your own hands. How to do this is shown on

Water does not merge

What to do if the Hayer washing machine does not drain water? It is necessary to check the drain system, maybe the blockage has formed there. You can do this repair with your own hands. How to check the pump drain filter:

The heating element is faulty

How to understand that Ten has stopped working? Pay attention to the quality of laundry washing. If the process takes place in cold water, things will be washed ineffective, a musty smell may be felt.

Also, 15-20 minutes after the start of the cycle, touch the hatch door. If it is cold, then he does not occur.

Most often, the heater fails due to scrap or short circuit. You can check the health of the heater with a multimeter. How to do this is shown on

Problems with electronics in the machine Hayer

Error codes ERR6 and ERR7 on the scoreboard SMA are talking about electronic malfunctions. Try to restart the car, turning it off the network for 15-20 minutes. If the code has not been removed from the screen, then it is required to take more serious measures.

It is difficult to carry out your own repairs here if you are not a professional master. Therefore, in this case, it is better to contact the service center.

Now it will be easier for you to navigate and find the reason for the problem. Do your own repairs or not. decide.

Basic errors of smie haier

For the convenience of recognition of errors that the Haier washing machine gives out by codes, they are divided into certain groups.

Errors made when operating the User

It happens that the owner of the washing machine allows erroneous actions. does not fall asleep the powder, overloads the drum with things or lays them out unevenly. For each wrong action, the machine meets a specific code:

Problems with water fence and its drain

Breakdown of this nature is quite common, and they are considered the most common. For this reason, a large number of codes that are listed below are allocated in the system of self.diagnosis of a Haier machine of Haier

Difficulties arising with heating water

It was the turn to tell about errors associated with maintaining the temperature regime of water in the washing device from Haier. We list codes of these problems error:

Errors meaning problems with electronics and electrician

Small Haier is known for a large number of wires and sensors that support the functionality of the machine. And the module is controlled by such a complex system, ensuring performance. When something breaks, the system gives one of the preventive codes:

If there are problems related to the operation of an electric engine on the Haier machine, then ERR 13 error code will appear on the screen. This means that the motor has burned out, or there is no voltage in the winding. How to eliminate such a malfunction? It is necessary to check the brushes and winding, perform a replacement, if there is such a need.

The work of the test mode

Sometimes the Hayer washing machine does not immediately sign up about the problem that has appeared, but the user himself understands that problems exist. In this case, you can use the test mode, which is launched as follows:

By numbers that appear on the screen, you can determine which element is checked:

If the signal on the screen is displayed for no obvious reason, the discharge should be carried out. But when he resumes, he should no longer ignore him.

Test and change the inlet valve

If the matter is not in the press, you will have to pay attention to the electromagnetic valve. It is located on the rear panel of the Hansa washing machine, near the location of the bulk hose

It will not be difficult to detect the element. You can check the inlet valve with a multimeter. Tester probes are applied to the coil and contacts of the sensor. Having discovered the malfunction, you will have to replace the part of the whole, the electromagnetic valve cannot be repaired.

If there are no problems with the electrician, you need to check the flow filter. The net is located here, in the place where the bulk hose is connected. The filter element is often clogged with impurities and covered with lime coating. After cleaning the part, it is worth returning it to its place and check if the washer earned it.

A mistake related to the drain of water from the tank. Appears on the scoreboard four minutes after the start of the operation. Informs of possible clogs and/or problems in the following elements of the drain system:

It is necessary to carefully diagnose the appropriate nodes, eliminate small malfunctions, for example, overcuts of the hoses. If possible, carry out the necessary repair work. You may need to replace some details.

We test the control module

If, when diagnosing the electric motor of the Haier washing machine, no violations were detected in its work, you will have to “dig deeper”. Failed code 7 may indicate the incorrect work of the main managing module. It is quite difficult to repair the control board, this requires certain knowledge and experience with electronics.

At home, you can conduct a visual inspection of the module. Learn the fee at the time of programs, damage and other defects. To inspect the main block, it should be:

• de.energize the washing machine;
• extract a dispenser from the body for detergents (pull the tray on yourself, pressing on the central latch);
• unscrew the bolts fixing the washing panel;
• Using a thin screwdriver, unclench the holding panel of the latch;
• neatly, so as not to break the wiring, put the control panel on the washer cover.

The “brain” of the Haier washing machine is located directly beyond the control panel. Before disconnecting the wiring from the block, be sure to take a picture or draw a connection diagram. After gently turn off the wires and remove the control module. To get directly to the main board, you will have to unclench the latches of the block body.

Carefully inspect the control board. If you find burnt sections or other defects, you will have to repair the part. Separate elements of the board can try to fix it yourself. This will require a soldering iron, multimeter and components for replacement.

The upcoming front of work during breakdowns of various kinds.

• Capacitor. Acts as a certain stabilizer on the board. When detecting the capacitor breakdown, it is necessary to solder a new element to a positive electrode. The polarity of the electrodes can be clarified using a multimeter.
• Resistor. The diagnosis of the element is carried out using a tester. First.order resistors ideally show the resistance of 8 Ohms and the value of overload 2 amperes. The second-order elements give out indications in 3-5 amperes, and the resistance value is directly related to the frequency of the module. If the measured indicators are inconsistent, the components are replaced by soldering.
• Thyristor block. The negative resistance of the switch is measured. Indications on the multimeter should not exceed 20 in.
• Block filter. This element can burn out. Elimination of the cathode will help to eliminate the malfunction.
• Trigger. The voltage at the input contacts is detected. The optimal value of the indicator is not more than 12 in. The normative resistance of the trigger filter is 20 Ohms. The installation of a new element is carried out using soldering.

The cause of damage to the control board is strong vibrations of the machine or voltage surges on the network

Therefore, it is important to install the equipment correctly, in order to avoid premature breakdowns. With vain attempts to reset the malfunction code, contact the service center

Indicates the fact that the machine does not cope with the water bay. The fact is that the water should fill the tank until a certain level for the set period of time (as eight minutes). If this does not happen, then the following reasons should be considered:

• low water pressure in the system;
• water does not flow due to a closed valve;
• The grinding valve grid was clogged;
• malfunctions of the valve itself, press stratum or pump;
• wiring defects located between the pump and the control module.

What does UNB mean?

In the washing machines of Haier all modifications, the appearance of the Unb error code means an uneven distribution of linen inside the drum. To avoid imbalance, the system begins to automatically place things inside the drum by rotating it in different directions.

HotPoint-Ariston RST 602 ST K. a separate washing machine, with a front load up to 6 kg., electronic control and squeezing speed 1000 rpm. To turn off the “console blocking” click and hold the “buttons block” key 3-5 seconds.

How to urgently open a haier washing machine?

In these machines, to stop and open the drum hatch, you need to install the machine in the pause mode. Then turn off the power and wait from 1 to 3 minutes. Then a click will be heard, notifying the unblocking of the hatch.

2) In order to fulfill the full reset of the error, you should also use the “Start” or “pause” key, holding it for about five seconds. After zeroing, the lock is unlocked, but the water will remain in the drum. If it has not merged, the lock is still unlocked (the excess must be drained through the drain filter).

Error codes Haier washing machine

The Haier washer self.diagnosis system, when a malfunction is not allowed, issues a malfunction code for the panel. In electronic models, an error shows on a display or on a scoreboard, on washing rooms without a screen will flash indicators. Therefore, it is easier for you to understand the reasons for the problem, just understand the value of the code.

After reading the material, you will save time on diagnosis and find out: what does the error code mean, what needs to be done when it appears. As well as how to fix, or eliminate a breakdown with your own hands.

Error table: what the codes in the washing machine Hayer mean

Verification of the press.start of the press, installation of a new part.

Unscrew the tap. Perhaps it is not completely open or blocked.

Rinse the filter skeleton of the fence valve.

There is more water in the tank of the Haier washing machine than necessary for washing.

Failure of the press starter (water level sensor).

It is necessary to replace the level sensor.

Checking wiring for defects and damage, repair of defective sections.

To reset the error, check the submarine tray.

Inspect the channels of the flow of powder into the tank, clean.

Now you know what the codes of malfunctions in the washing machine Hayer mean. You have the opportunity to independently diagnose the problem and carry out repairs with your own hands.

There were problems with the washing machine? Self.diagnosis system will help to deal with them. Washing machines Wiztel with electronic control show the error code on the display. Electromechanical.

When the Zerowatt washing machine gives the error code on the scoreboard, everything that the user needs is to understand its value. The self.diagnosis system acts in such a way that if a malfunction is detected here.

Error codes of washing machines Haier

For laminated Haier washing machines, quite long codes are used, for example ERR4, along with ordinary E4. Below is a complete list of Here errors.

In the Samodelkin online store, you can order spare parts for Haier washing machines with a guarantee delivery.

• There is no washing powder in the tank.
• expensive models of Haier washing machines, for example, HW80-B14686, react to a low-quality remedy with the same code.

• Pour the powder.
• If it is already poured. the channel of his fence in the tray clogged, the car cannot wash it. Remove the tray and rinse it from dry powder and scale.

The car slowly rotates or does not rotate the drum at all.

• Make sure that the amount of loaded linen corresponds to the required standards. Probably a lot of them.
• Straighten out the laundry if it fell into a lump and cannot distribute evenly in the drum.

The washing machine refuses to start washing.

• Check if the hatch is tightly closed, open and close it to a characteristic click again.
• If this does not happen, examine the external device of the lock: hook and nest. Often the impossibility of closing the door is associated with mechanical breakdowns. They need to be eliminated by replacing the details.
• Check UBB (Luke lock device), repair or replace the device.
• Check the integrity of the drain hose, eliminate creases and blockages, and better. replace the spoiled hose.
• Inspect the drain pump: it could clog (clean and install in place), or break (replace).

The machine does not warm the water sufficiently (relevant for programs where it is supposed to heat water), or heating does not occur at all.

The washing machine does not gain or very slowly collects water in the due period of time.

• Water supply problems.
• The inlet valve malfunction.
• Failure of a pump or press start.

• Make sure that there is water in the water supply, and its pressure is sufficient.
• Inspect the water supply tap and open it sufficiently.
• Rinse the inlet valve filter and install in place.
• Inspect the pump and press streams for defects. If there are defects in them. eliminate by repair or complete replacement of components.

The car does not work at all, does not respond to commands.

• Inspect all the control circuits of the control unit that the reason is in them.
• Make sure the correct location of electric elements, install them in place and fix them.
• Eliminate the cliff, start the car again.

Critical error: often this is the failure of several parts of the control unit.

• Careful diagnostics of the control unit. Replace the failed components or the entire block.
• From now on, you should try not to allow short circuits (for this it is worth connecting the device through an external stabilizer)

The washing machine is gaining a lot of water.

• Pressostat failed.
• Simistor burned out.

• Inspect the press, eliminate the cause of the breakdown, or replace it with new.
• Replace the symistor.

The car does not respond to commands, does not make sounds, does not perform a work program.

What can be done yourself?

If the door is blocked and does not open, first wait 2-3 minutes after the end of the cycle. In modern Hyer models, an electronic lock is installed, so you will not be able to open the unit right away.

If the program hung up due to the voltage jump, and the technical “glitch” arose, try to restart the device. To do this, disconnect it from the mains for half an hour, and then turn it on and restart the program again. The controller will drop the settings and start working in normal mode.

Also check the Haier washing machine to include the function of protection from children. How to unlock the device in this case? Everything is simple. You need to press a certain combination of buttons. Information about the disconnection of the option can be viewed in the operating instructions.

If the machine door is blocked, there is water inside, it is worth checking the elements of the drain system. You can independently inspect the hose and filter. There should not be overcurrents and damage on the hose. If it is limp or crushed by furniture, straighten it. If the blockage inside. rinse under running water and set in place. In the presence of damage, the hose must be replaced.

The drain filter is located in the right lower part of the case. It needs to be unscrewed, remove the garbage and rinse, and then install it in place. Before removing the filter, put the container down, as water will come out of the tank.

How to unlock the Haier washing machine in emergency

Emergency methods of unlocking of the smell are often indicated in the instructions and depend on specific models of technology. There are several basic methods that can be resorted to before the arrival of the master.

How to open the door of smoke? Can be used for this:

• Cable of emergency opening. It is located under the facade of the filter cover. If you pull it for it, the door will open. But at the next wash, it can be blocked again, so the master will have to be called in any case.
• Pliers. The method is relevant when crayfish breakdown. If its fragment remains, pull it with the help of pliers.

Before starting manipulations, disconnect the machine from power. Then drain the water from the tank (if any) through the drain filter. If an error code appears on the display, look at its designation. With a clear indication of a breakdown of any component of the unit, do not try to open the door yourself-immediately call the master.

Washing machine Haier error codes

Haier, although it is considered developing, the quality of the washing machines manufactured by consumers is highly appreciated by consumers. But in their work, there are still malfunctions, about which the washing machine immediately signals the codes issued on the screen of the panel. If you know the codes of the Haier washing machine errors, you know how to decipher the alphabetic digital values, then you can quickly determine and eliminate many breakdowns on your own.

For the convenience of recognition of errors that the Haier washing machine gives out by codes, they are divided into certain groups.

Errors made when operating the User

It happens that the owner of the washing machine allows erroneous actions. does not fall asleep the powder, overloads the drum with things or lays them out unevenly. For each wrong action, the machine meets a specific code:

• No Solet. Error means that there is no washing powder in the tray, or the canal of the powder receiver is clogged. Sometimes the machine gives out such a reaction to a low.quality washing tool,
• UNB. using such an error code, the Haier washing machine reports that an imbalance has formed in the drum,
• ERR1. The code appears if the washing machine is not able to activate the washing due to a poorly closed loading hatch. In addition, such an error may appear if the lock device breaks down.

Problems with water fence and its drain

Breakdown of this nature is quite common, and they are considered the most common. For this reason, a large number of codes that are listed below are allocated in the system of self.diagnosis of a Haier machine of Haier

• ERR2. using such an error code, the Haier machine reports that the water, according to the time specified by the program, does not merge. Perhaps in the pump or drain hose, blockages formed, the latter could just twist,
• Err5. means that water is not pumped into the car of the car. This may be due to insufficient pressure in the tap network, a closed tap, a suction filter block, a valve power violation, which is responsible for the inlet, failure of the pump or press startup,
• ERR8. This code in the Haier washing machine helps to find out that there was more water in the tank. What is necessary. In most situations, this happens if a press starts out of the system. A signal is very rarely made by such an error that the seven.landing on the management board is broken, which controls the sensor that controls the fluid level,
• ERR9. This code should be decrypted, like the previous. The only difference is that it is a signal of errors that arise for other reasons. it blocks the intake valve, the sevenistor responsible for its control is out of order,
• ERR10. means a breakdown of the hydraulic system, but at the same time, the inlet valve continues to function normally, and most often the press.steam.

Difficulties arising with heating water

It was the turn to tell about errors associated with maintaining the temperature regime of water in the washing device from Haier. We list codes of these problems error:

• ERR3. literally deciphered as follows: Ten cannot heat the liquid to a given temperature program. In addition, the code can indicate that the heating element completely fails. The main causes of the problem are a violation of the temperature sensor or its breakdown,
• ERR4. the code is deciphered in the same way as the previous one, but the cause of the breakdown is a burned out heating element, or violations in the electrical wiring.

Errors meaning problems with electronics and electrician

Small Haier is known for a large number of wires and sensors that support the functionality of the machine. And the module is controlled by such a complex system, ensuring performance. When something breaks, the system gives one of the preventive codes:

• ERR6. this is how the module failure is confirmed. Probably, damage appeared on one of its paths, or a semiconductor element failed, the contacts from the track to this element were disturbed,
• Err7. this code is rarely displayed. With its help, the car reports that several modular details were burned out at the same time, and the malfunction is considered a critical. As a rule, this happens with a short circuit, and the refusal is considered really serious,
• Euar is another serious problem associated with the management module. Rarely, but such a code appears if a whole bunch of wiring is burned out.

If there are problems related to the operation of an electric engine on the Haier machine, then ERR 13 error code will appear on the screen. This means that the motor has burned out, or there is no voltage in the winding. How to eliminate such a malfunction? It is necessary to check the brushes and winding, perform a replacement, if there is such a need.

The work of the test mode

Sometimes the Hayer washing machine does not immediately sign up about the problem that has appeared, but the user himself understands that problems exist. In this case, you can use the test mode, which is launched as follows:

• The “Start Delay” and “Without Plum” buttons are pressed simultaneously and hold for some time,
• It is necessary to make sure that the loading hatch is closed,
• door lock is activated after ten seconds,
• Testing is running.

By numbers that appear on the screen, you can determine which element is checked:

• 77:77. The electromagnetic valve is diagnosed,
• 66:66. The electric motor is checked,
• 55:55. Pressostat is tested,
• 44:44. there is a check of the motor at the time of its operation,
• 33:33. Virgins is checked for performance,
• 22:22. The drain pump is tested,
• End. testing completed.

If the signal on the screen is displayed for no obvious reason, the discharge should be carried out. But when he resumes, he should no longer ignore him.

The Haer washing machine gives an error code. how to eliminate the malfunction

Despite the fact that Haier is young and developing, the quality of its products is evaluated quite highly. But nevertheless, failures occur in the operation of washing machines, about which the washing machine will instantly tell the consumer the withdrawal of a certain letter-civilian value on the display.

Therefore, knowing the codes of errors. the Haier washing machine is no longer a “mysterious object”, most malfunctions can be completely eliminated independently.

The program failure is associated with the breakdown of the door lock or with the failure of the Luke lock device. It is necessary to repair the uble and/or lock. If there is no such possibility, then replace the appropriate details. Often, a mistake can be displayed simply because the user himself covered the drum door loosely by carelessness.

A mistake related to the drain of water from the tank. Appears on the scoreboard four minutes after the start of the operation.

Informs of possible clogs and/or problems in the following elements of the drain system:

It is necessary to carefully diagnose the appropriate nodes, eliminate small malfunctions, for example, overcuts of the hoses. If possible, carry out the necessary repair work. You may need to replace some details.

The system issues this code if the lack of control directly related to the thermal attemptor appeared in the washing machine, that is, the lubricants are not able to heat water to a given temperature. The most likely reason is the failure of the temperature sensor. Replacement is required.

This error is also associated with heating water. Means that the heating. Can only be corrected by its replacement.

Indicates the fact that the machine does not cope with the water bay. The fact is that the water should fill the tank until a certain level for the set period of time (as eight minutes).

If this does not happen, then the following reasons should be considered:

• low water pressure in the system;
• water does not flow due to a closed valve;
• The grinding valve grid was clogged;
• problems of the valve itself. Pressostate or pump;
• wiring defects. located between the pump and the control module.

The control module has problems. It is possible to have defects on the board, violation of any contacts or sections of the wiring.

A critical error, indicates problems in the electronic unit.

• there is a short circuit;
• The machine was operated for a long time in a room with an increased humidity;
• one of the paths of the module is damaged;
• Semiconductor elements failed;
• The contact between the semiconductor and one of the tracks, that is, in the block, which approaches the modular board of one (several) wires, “sits” in the block.

This error requires professional elimination. It is more advisable to attract an electrical specialist.

A failure in the operation of the water collection system, that is, its volume in the tank is much larger than it is required for high.quality washing. The most common reason (about 95-97% of all cases) is a “culprit” is a breakdown of the press. It is also often possible to find a breakdown of the water level sensor or electronic controller.

Pressostat

It is determined similarly to the previous error. However, the reasons that provoked it were several other. Such a problem can be caused by a burnt bulk valve and the simistor who controls it. In this situation, the module is not able to stop the water supply to the tank.

ERR10

Also informs about failures in the operation of the SMA hydraulic system. Most likely they are caused by breakdown of the press starting with a normally functioning fill valve. It is required to replace the failed part.

Dysbalance of the drum. Arises due to the fact that the loaded underwear was distributed during washing unevenly. Stop the washing program, open the hatch and redistribute the location of things. Also, an error may be displayed if one large (heavy) or, on the contrary, is too easy to wash.

Problems of the functioning of the electronic board arising as a result of electrical disorders. It is necessary to check for defects the wiring and controller block. If necessary, eliminate the malfunctions or replace the.