Home Refrigerators The refrigerator Stinol reasons stopped working
Refrigerators

The refrigerator Stinol reasons stopped working

Stinol 110 does not turn on. Possible reasons for the failure of the refrigerator

STINOL is one of the few domestic manufacturers of refrigerators, which for a long time occupied a leading position in the market and the CIS countries. At the moment, Stinol refrigerators are not produced, but our compatriots have a sufficient number of working household appliances of this brand in the apartments. Despite the high quality of the assembly, over time, various malfunctions of Stinol refrigerators are found, which can manifest themselves differently depending on the causes of their occurrence.

What to do if the refrigerator Stinol broke? Do not rush to call specialists, because many malfunctions can be eliminated independently, because their cause is our inattention or violation of operating conditions.

Почему не включается холодильник.Перестал работать холодильник.Замена термостата холодильника Стинол

STINOL refers to the most common signs of a breakdown of two.chamber refrigerators:

  • The refrigerator does not turn on.
  • The compressor is constantly working.
  • The refrigerator is poorly freezing.
  • Light does not burn or problems with indication of light bulbs on the control panel.
  • Problems with the No Frost system in the freezer.
  • Water flows in three.chamber and two.chamber refrigerators with the “Crying Wall” system.

There are a lot of reasons for the emergence of certain malfunctions, so let’s look at each option in more detail.

The refrigerator does not turn on

If the refrigerator does not work, then there may be several reasons for this:

  • The device is not connected to the network, the power cord is damaged or the light was turned off in the apartment.
  • Refrigerant leak also leads to the fact that the refrigerator has stopped working. It is almost impossible to accurately set a breakdown site without special equipment, but there is one visual sign. from the outside on the back there was a bloating of isolation.
  • Another reason is the failure of the compressor or breakdown of the relay-breaker. A characteristic sign of a broken relay is a sharp loud click that is heard after turning on the refrigerator, after which it turns off.

If the matter is in the temporary absence of electricity in the apartment or the free fit of the contacts of the fork in the outlet, then these problems are easily eliminated on their own.

If this did not help and the refrigerator STINOL does not turn on. turn it off from the network and call it specialists. The refrigerator does not turn off

There are several situations when the Stinol refrigerator does not turn off and continues to work for a long time without rest. In most cases, this is not normal, because the work of the motor is cyclical, which implies regular disconnecting and turning on the unit.

The most common reasons when the refrigerator does not turn off:

The “Super.Summary” or “Fast cooling of products” was established.

In this case, the freezer or refrigerator will constantly work until it reaches the default temperature. In this mode, the compressor does not turn off and continues to escalate the cold until 8 hours in a row.

Violation of sealing the seal or an unclosed door.

The refrigerator will always strive to achieve the required mode, but due to the presence of warm air, the compressor will work all the time. Indirect feature. frost around the perimeter of the door.

Control system or failure of a thermal attemptor.

A special sensor inside the freezing camera or refrigerated compartment determines the current temperature and when the set value is reached. directs the signal to the control module, which gives the command to disconnect.

What are the features of Stinol refrigerators

The case of the refrigerator of this brand is a standard rectangular cabinet, the interior of which consists of 1 or 2 built.in cameras. The surfaces of the freezer compartment are made of a durable polymer. Between the case and the camera there is a laying of polyurethane foam with good heat.insulating properties.

The capillary system of pipes is used as a throttle. Thanks to this element, the sensitivity of refrigeration equipment to pollution and high humidity increases. The number of compressors depends on the refrigerator configuration. The motor located at the bottom of the cabinet has a vertical axis. The evaporator is made in the form of a curved metal tube enclosed in metal plates. There are 2 types of such elements:

Compressor electrical system device

The main element of the refrigerator is the engine. It is necessary to organize the circulation of the refrigerant, and in our case, Freon, by tubes. In addition to the unit itself, the following elements are in the system:

The engine includes a rotor and starter. The design of the latter is several copper coils. While the rotor is more like an ordinary steel shaft working in a tandem with a piston engine system.

When the unit is turned on, electromagnetic induction is formed in the coils, which serves as source of torque. Further, the rotor begins to rotate at the expense of centrifugal force, and at the same time the piston moves.

In modern models, the engine is located inside the compressor, which minimizes the probability of spontaneous leakage of the refrigerant. The system in its original form is subject to strong vibration. To reduce it, a special metal suspension on the springs is provided.

On new models, the latter are fixed inside the case, while on the old ones. from the outside. The first option is more practical and allows you to noticeably extinguish vibration more effectively. But in the case of suspension breakdown, organizing repair is much more difficult.

The motor will work until the required temperature is set in the cells, after which the thermostat is connected. He opens the contacts, and the current stops going to the engine. The compressor also stops its work. Когда температура повысится, контакты термостата вновь замкнутся, и цикл продолжится.

In the models of the Midnetnit and budget category, the thermostat is often out of order. The element has far from the most complex design and costs a penny, so it is much more practical not to repair it, but to buy a new.

The refrigerator does not turn off

Freezer from below, two engines (two twists of thermal controllers) separately on the refrigerator and freezer chambers

Little cold or no cold in the refrigerator. perhaps an increase in a fur coat or an uneven block

Blockage of the capillary tube of the refrigerator (treated or piercing a blockage. either by installing a crying evaporator. a refrigerator duplicate built into the wall)

2.Freon leak in the refrigerator. In this case, a crying evaporator is put an example of working on installing a crying evaporator on a similar refrigerator: https: // holodilchic.ru/nashi_remonty/remont-kholodilnika.tlant-1704/

Faulty thermoregulator of refrigerated chamber

A faulting motor-compressor of the refrigerator, or in the rare case, its start-up relay is faulty

Little cold or no cold in the freezer

If freezers without the No Frost system (No Frost)

Zarori capillary tube of the freezer chamber example of working on replacing the capillary tube with a similar refrigerator https: // holodilchic.ru/nashi_remonty/remont-kholodilnika-ariston-hotpoint.romba-1185/)

The freezer motor-compressor of the freezer is faulty or in the rare case its launcher-protective relay.

The thermostat on the freezer almost never fails if the freezer with the No Frost (No Frost) system as a rule in this case does not turn on the freezer (does not freeze) the person who does not know whether the NO FROST system is not aware or not. You can according to a button to turn on the fan. When you open the freezer, she finds it on top of the shelves in the upper right corner and looks like a trigger

Upper or lower heater of the No Frost system

Freezer from above (one motor)

Little cold in the refrigerator (works without stopping)

-Upper or lower heater of the No Frost system

The reasons for this malfunction

The causes of the malfunction can be common to different models, and can only hit certain models. For example, Stinol refrigerators with the No Frost (No Frost) system have its own characteristics and nuances. You can find out more about this in the service repairing stinol refrigerators.

  • Violation of the rules of operation of the electrical appliance:
  • The irregular mode has been set. at an elevated air temperature, the regime of the highest cooling is used (switch the mode to the maximum)
  • The device is installed in a room with high humidity. the parts are oxidized (call the electrical wiring with a multimeter)
  • Foreign objects fall into the drainage system. the tubes are clogged, subsequently the water cannot leave and forms ice, which either jams the fan or clogs the passage through which cold air is ongoing
  • used with increased voltage on the network. the motor burned down
  • With reduced voltage. the starting relay is triggered
  • The refrigerator is pulled very close. the engine overheats
  • Technical wear of details due to the “age” of the refrigerator after 10-15 years of service:
  • The electric (network) cord was flooded or the fork broke and the voltage does not arrive
  • There was a problem with a socket
  • the elastic band is worn. the seal and the door of the refrigerator does not fit tightly
  • Corrosion of metal parts
  • Violation of the integrity of protective coatings
  • Failure of the main nodes of the refrigerator
  • motor. compressor
  • engine
  • fans
  • Thermostat
  • launcher

Individual reasons:

In single.chamber refrigerators:

  • The freezer does not freeze. damaged by manually. it happens if “help” to defrost with sharp objects (knife, screwdriver)
  • There is a lot of hoarfrows on the back wall and it does not decrease, but on the contrary, it intensifies even more. insufficient amount of coolant. freon
  • The fan is not heard, despite 10 hours of defrosting, the fan motor burned
  • The motor is buzzing, but with long interruptions. a broken thermostat and does not give a signal about the temperature in the freezer
  • There is no hoarfrost on the back wall. the motor burned. compressor

In two.chamber refrigerators:

  • Damage to the refrigerator or case
  • Capillary tubes are damaged
  • Violation of the function of the freezer
  • Freon leak: Damaged tubes
  • The thermorela broke
  • Thermoregulator failed
  • The thermostat is not adjusted
  • Problems with the compressor
  • Malfunctions with automatic defrost

Do.it.yourself repair

Non.critical breakdowns are eliminated independently, but with a thorough analysis and study of the breakdown, as well as the availability of experience. Without experience, but with a firm intention to defeat a breakdown, only the most elementary malfunctions can be eliminated.

For example, even a woman can repair the gum of the door sealing. It is necessary to heat the gum with a hairdryer in the places where it moved away from the body, then close and tightly press the door, do not touch it for a while. Or, for example, a network cord and fork. A man who knows a lot about this matter will not be difficult to replace it, and the refrigerator’s function will be restored.

Only a master. professional should be engaged in more complex breakdowns.

Why does the stinol refrigerator not freeze and how to fix the situation

Stinol refrigerators. products of the refrigerators of the same name of the same name. This company is a division of the Novolipetsk Metallurgical Plant. The name of the brand is a reduction from “Steel from Novolipetsk”. In the middle of the two thousandth, the plant was bought by the Italian company “Indesit”. One of the frequent problems of Stinolov’s devices is not a low temperature in the refrigerator or freezer.

Of course, if the stinol refrigerator does not freeze, then the best solution will be to contact the workshop. For example, to us: Repair of Kazan refrigerators. However, before calling the master at home, you should try to deal with the problem yourself.

Deviations from the norm

The normal temperature for storing products in the freezer is considered.18 degrees, in the second department 5 degrees. With such indicators, the products do not deteriorate. In order to make measurements, you need to put a container with water and a thermometer for several hours in the refrigerator at such a temperature in the refrigerator.

If the problems are noticeable without any measurements, you need to start with the elimination of the simplest reasons:

  • The manufacturer indicated that the Stinol refrigerator should be operated at a temperature of not higher than 32 degrees. Therefore, in the summer, Stinolovsky devices can work incorrectly. The refrigerator should be removed from heat sources, make sure that the sun’s rays do not fall on it, which in the hot season contribute to heating the body.
  • Products before sending for storage should be cooled. Do not exceed the rate of bookmarking by weight. Some owners have a bad habit of holding the door open for a long time, choosing a product. It is harmful to the refrigerator.
  • Sometimes a temperature regime is incorrectly set. If there is a need to replace a thermostat, you can contact the STINOL refrigerators service at home.

Independent diagnosis

First of all, they recommend a defrosting of the unit, and then turn it on again. This alone can help. It is useful for some time to put the regulator to position 1. If these measures do not benefit, most likely the reason for the lack of frost is as follows:

  • The leature of the door seal. Especially relevant for devices with long.term operation. Tested visually, to the touch and using a sheet of paper. The sheet is obsessed between the door and the body, the door closes. If the paper is well fixed, everything is in order. Thus you need to walk around the entire perimeter of the rubber nozzle. Where the sheet will move freer. and there is a place of air penetration inside the chamber. At home, a problem place can be heated with warm air, given the correct shape and close tightly. Feng is suitable for this purpose. If the deformation is large, you have to replace the part.
  • If a snow cap has accumulated inside the freezer, you need to look at the back wall. is there any detachment. Such deformation violates normal heat transfer between the freezer and the next camera and the refrigerator STINOL does not freeze. You can diagnose such a problem in a neglected form even to the touch: the wall will bend. Or visually. it is swollen. Such a nuisance sometimes happens to STINOL devices if the correct assembly conditions are not met, or poor.quality details were used. Repair of such a breakdown is not a matter of light, and does not always give a positive result. Some masters advise to press the wall more tightly by shelves. People’s craftsmen sometimes try to fasten the exfolved part with plastic bolts. But with careless drilling, you can damage the evaporator contour, and this is even more serious breakdown.
  • It is necessary to listen to the compressor work. Is he buzzing? Works with or without breaks? If the compressor does not publish any noise for a long time, then it probably failed. Without normal compressor operation, the Stinol refrigerator will not freeze. Symptom of the incubation. the work of the motor without a break. Soon it will certainly become unusable, you need to urgently take measures. Determine what exactly has broken in a compressor. for an unprepared person a difficult task, it is better to seek help from a specialist or workshop.
  • Normal heat transfer in the refrigerator is hindered by the blockage in the tubes along which the refrigerant moves, especially in the capillary tube. This is diagnosed using special devices, at home you should listen to the sounds of the refrigerant in the freezer. In the case of a blockage from the freezer, a characteristic quiet murmur of Freon is not heard. You can eliminate the blockage independently, having special equipment.
  • Frequent cause of deviations in work. Freon leakage. If it was not possible to find a crack in the circuit, there is no oil spots on the refrigerator or near it, you can diagnose the loss of the refrigerant by measuring the pressure in the circuit. For this, specialized devices are also needed. In most cases, the elimination of holes and filling the refrigerator by Freon can only be carried out by a specialist.

If you decide to defrost the Stinol refrigerator with the No Frost system, be sure to defrost at least a day with open doors. It is necessary that there is no water left in the drainage system, otherwise the technique simply will not freeze properly.

Stinol refrigerators

STINOL is one of the few domestic manufacturers of refrigerators, which for a long time occupied a leading position in the market and the CIS countries.

At the moment, Stinol refrigerators are not produced, but our compatriots have a sufficient number of working household appliances of this brand in the apartments.

Despite the high quality of the assembly, over time, various malfunctions of Stinol refrigerators are found, which can manifest themselves differently depending on the causes of their occurrence.

The most common malfunctions of Stinol refrigerators

What to do if the refrigerator Stinol broke? Do not rush to call specialists, because many malfunctions can be eliminated independently, because their cause is our inattention or violation of operating conditions.

Выезд на тестирование холодильника Stinol 103

STINOL refers to the most common signs of a breakdown of two.chamber refrigerators:

  • The refrigerator does not turn on.
  • The compressor is constantly working.
  • The refrigerator is poorly freezing.
  • Light does not burn or problems with indication of light bulbs on the control panel.
  • Problems with the No Frost system in the freezer.
  • Water flows in three.chamber and two.chamber refrigerators with the “Crying Wall” system.

There are a lot of reasons for the emergence of certain malfunctions, so let’s look at each option in more detail.

The “Super.Summary” or “Fast cooling of products” was established

In this case, the freezer or refrigerator will constantly work until it reaches the default temperature. In this mode, the compressor does not turn off and continues to escalate the cold until 8 hours in a row.

Violation of sealing the seal or an unclosed door

The refrigerator will always strive to achieve the required mode, but due to the presence of warm air, the compressor will work all the time. Indirect feature. frost around the perimeter of the door.

Control system or failure of a thermal attemptor

A special sensor inside the freezing camera or refrigerated compartment determines the current temperature and when the set value is reached. directs the signal to the control module, which gives the command to disconnect. In the case of a failure in one of the nodes (sensor or module), the compressor does not receive commands and continues to work. If you do not contact a specialist in time, then the compressor will quickly fail, as it will work for wear.

The refrigerator is badly freezing or even stopped overstruming the cold

In addition to domestic reasons (accidental shutdown from the control or de.energization panel), the refrigerator does not freeze in only a few cases:

  • Refrigerant leak.
  • Compressor breakdown.
  • The failure of the protective motor relay.
  • Electromagnetic valve breakdown (for two.chamber single.compressor refrigerators).

Each of faults can lead to the fact that the refrigerator stopped freezing for no apparent reason.

The situation is a little different when the stinol refrigerator is in working condition, but the cold is not enough. The most common reason is the random adjustment of the thermostat handle (temperature reduction). If the handle is mechanical and is located inside the refrigerator compartment, then it can be easily offered during loading/unloading products (especially in the upper chamber).

If a model with electronic control, then a possible reason will initially be the wrong setting of the operating mode or the game of children. Check the position of the thermostat handle or the set temperature value on the display. Also, one of the reasons may be the incorrect factory calibration of a thermal attemptor and control unit.

In this case, it is worth contacting specialists who will repair the refrigerator at home.

No light or an indication problem

If the lighting bulb inside the refrigerator does not turn on, then there are only three probable causes of a malfunction:

  • The incandescent lamp just burned out, and it must be replaced.
  • The pusher key broke (a spring flew out). In this case, it will be advisable to replace the entire backlight unit along with the plafon and button.
  • Cliff in the electrocope of the refrigerator. In this case, you can not do without the help of a qualified specialist.

If the STINOL refrigerator does not burn or specific operating modes of the refrigerator, then the simplest reason is the absence of current on the network or the mechanical switch on the front panel is in position “0” or “OKL”. If the problem is not this, then the face violation of contacts in the indication system or failure of the control module.

Problems in the No Frost system

One of the last Stinol refrigerators that came off the assembly line in Lipetsk. there were models with the automatic thawing system No Frost. During the operation, the main malfunctions were manifested, which have the following signs:

The freezer is buzzing

Most likely there were problems with the thawing system, and hoarfrost began to form on the back of the evaporator. A fan that evenly distributes the air inside the freezer begins to rub on a snowy “fur coat”, which causes extraneous sounds. Replacing the heating element of the thawing system in most cases solves this problem.

Inside the refrigerator is noisy, the beating is heard

In this case, the most likely reason is the breakdown of the fan. Constant rotation leads to the natural wear of the bearing group, the first sign of which are beatings and noise. It is recommended to replace the fan until it completely fails, otherwise there will be no uniform spread of cold air inside the chambers, which can lead to a failure in the operation of electronics.

Leak the refrigerator

If the refrigerator flows from below, then depending on the type of defrosting system, there are different reasons:

  • If the refrigerator Stinol No Frost flows, then the automatic thawing system is most likely out of order. If it is not repaired on time, then in a very nearby compressor will fail due to constant work for wear.
  • In the case of refrigerators from the drip system, there may be several reasons. the condensate container fell, the pipe jumped out or the drain hole was clogged inside the refrigerator. All these malfunctions are eliminated independently without involving specialists.

Reasons why the stinol refrigerator does not freeze

In the modern two.compressor unit with the No Frost system, two separate relay controls the temperature inside the chambers and two separate contours are cooling.

If a household refrigerate unit works, but cannot maintain the necessary temperature in the upper chamber, and in the lower products are well cooled, the reason is either in improperly set settings, either in internal breakdown, or in the leak of the grocery compartment.

You can understand for what reason the stinol refrigerator is badly freezed if you perform a number of actions.

Long defrosting and correct inclusion in the work

Before any manipulations with the device, you need to turn it off from the network and remove products and empty containers from it. In order to understand whether to change the refrigerator according to the warranty or it is working, you need to defrost it completely and let it stand for a day without connection and without products. This is done in order to completely remove condensate from the system.

  • The reason that the upper chamber does not freeze in the refrigerator, and the lower one works, can be an accidentally selected fast frost mode or hasty simultaneous laying of a large number of warm products into the compartment.
  • Especially often the problem of poor cooling against the background of the good operation of the freezer is pursued by the newly purchased units.
  • Another reason why the top chamber of the Stinol refrigerator does not freeze is often a fan malfunction: its blades can be covered with ice and jam, which is why the leading electric motor can burn out.

You need to upload the device only after a few cycles of turning on-off the compressor and reach the operating temperature. Products need to be applied in small portions, taking breaks to cool them.

Elimination of warm air leaks into the upper chamber

If the defrosting did not help and the matter does not concern the new device, the reason why STINOL stopped cooling the products well, may be in the leakage of the sealing gum on the door.

The constant ingress of warm air outside does not allow the device to reach the desired mode and turn off the compressor, which provokes the rapid formation of ice (hoarfrost) on the back of the department. If defects are detected in the seal, it is necessary to replace it. You can do this yourself or calling the master at home.

Diagnosis of internal breakdowns of the refrigerator

Understand what the problem is and why the Stinol refrigerator does not hold the temperature poorly, you can look at additional symptoms of the malfunction:

  • The lack of a characteristic sound of his work is indicated about the breakdown of the fan. If, on the contrary, a loud noise is heard, it means that its impeller and working space are covered with ice and defrosting is required.
  • On the breakdown of the motor, which leads the compressor of the upper chamber, indicates the inability to launch the unit for more than a few seconds and the flow of oily liquid from under the case.
  • About the leakage of the refrigerant from the contour of the product section, in addition to the fact that Stinol has stopped freezing, several symptoms are said: bloating on the plastic walls of boxing and their icing (often uneven); spots and streams of rust on the case near the freezer; Long.term continuous operation of the compressor, an almost non.heated condenser wall. Sometimes symptoms are noted at the same time.

One common problem. the upper chamber of the refrigerator does not freeze for an unknown reason. it unites several more internal breakdowns, which only “opening” will help and diagnosis of individual units of the system.

Most often out of order on Stinol refrigerators, as on most others, they come out:

  • Start relay. The reason for its breakdown is wear or short.term voltage jump.
  • Filter-dryer. Oil decomposition products clog the capillary system and interfere with the circulation of the refrigerant.
  • Thermal attemptor or sensor sensor (on modern electronic models). Sensors stop working from a voltage difference or from internal defects.
  • Temperature controller. Relay fails either due to mechanical wear, or after a voltage jump.

It is possible to reliably establish why the STINOL refrigerator has stopped maintaining the desired temperature of the products, although the freezer works, only by opening and diagnosing the device. If the recommendations from the first part of the article have not come up and the upper camera still works badly, it is better to invite a qualified master. He will find out why this is happening.

Stinol refrigerator does not work, reasons

What to do if the refrigerator “Stinol” does not work? It is worth trying to determine the breakdown. Perhaps you can eliminate the problem yourself, and our article will help in this.

STINOL refrigeration equipment is known for high quality. The metal case of equipment is always covered with corrosion solutions, special painting technology provides prolonged operation without scratches and defects. But even high.quality technique can break.

The refrigerator does not turn off and constantly works

This is the most common cause of non.betting in the refrigerators “STINOL”. If your technique with one compressor does not turn off, pay attention to the signs of a breakdown. You may notice that the freezer department is normally freezing, and the upper refrigerator does not work.

The cause of the breakdown can be in the leakage of the gas-freon. This is a refrigerant that is responsible for cooling air in the departments. The leak may be in the steel circuit. To eliminate the malfunction, it is necessary to detect damage, eliminate them and refuel the system with freon.

  • The door of the refrigerator. How tightly it is closed? The cause of loose fit could be the loops that sagged due to the large load of the door. After pulling the loops, the door will be normal to close.It is worth checking the rubber seal. over time the rubber wear out and is polluted. You can replace the seal with your own hands.
  • Set temperature in the chamber. If electronic control, temperature adjustment is automatically performed, and if mechanical, then manually. Check, perhaps the “Super.Summarrons” mode is installed on the thermostat.
  • Ventilation quality. With poor ventilation or installation near the heating radiators, the refrigerator overheates. Trying to compensate for the temperature increase, the motor works without stopping.

If after the check everything turned out to be in order, the case is in the breakdown. What happened:

  • The termistor and thermoregulator broke. In this case, the control module does not receive temperature data in the chamber, so the compressor does not turn off. A faulty sensor needs to be replaced.
  • Clogging of the capillary tube. Due to depressurization, a blood clot formed in the tube, which does not allow the refrigerator to circulate normally. It is advisable to call a specialist who will find the location and eliminate the problem.
  • Fault of the motor-compressor. During prolonged operation, the motor parts wear out, as a result, the compressor lacks power to pump pressure into the tube, so the set temperature is not achieved. The motor needs to be replaced.

Do not wait for a complete breakdown of the motor. Call a specialist for repair, because during constant work on the compressor there is a double load.

For what reasons, the two.chamber refrigerator “Stinol” does not work

It happens that a two.chamber refrigerator does not freeze, and the light in the department is on fire. The cause may be a freon output again. You can understand this by ice on the evaporator or in the leakage area. The check is also carried out:

  • In modern models, installation is checked. If the case leaned forward, the door could open, so warm air enters the chamber. The refrigerator “understands” that it makes no sense to start the motor.The case should be slightly rejected back. To do this, twist the front legs of the refrigerator.
  • When heat and light does not burn in the cells, electrical parts are inspected: wiring, fork, network cord, outlet. Maybe something was overstated or damaged. Then you need to replace the spoiled element.

To make it easier for you to deal with a breakdown, we advise you to pay attention to the signs of a malfunction:

  • You noticed that the light in the cell is on, but the compressor does not start? Perhaps the clicks of the relay are heard, which is trying to start the engine. So the motor burned. The burnt part is not subject to repair, a new element is installed.
  • Refrigeration equipment (I) with electromechanical control does not work, but the light bulb is glowing. The temperature controller is faulty. He does not send the control board data, so the module does not include cooling.
  • If the light burns in HO with electronic control, but the compressor is “silent”, the termistor is checked. He measures the temperature in the chamber.
  • The bulb in the chamber does not glow, the technique does not turn on. There were problems with a start-up relay that launches the motor-compressor. The relay is replaced by a new part.
  • If the refrigerator does not at all give “signs of life”, while the wiring is working. the problem is in the control module, it cannot control the nodes and details in the technique. Therefore, diagnosis, flashing or replacement of the module is carried out.

No cold in the freezer

Most of the modern STINOL refrigerators are produced with two engines. Each of them is responsible for the work of the upper and lower chamber. If the freezer compartment independently defrosts and does not cool anymore, there may be two reasons:

  • Damage to one of the compressors. Check this is easy: touch both compressors. If they are hot, then the case is in the interitoral circuit. Perhaps the problem with the windings happened as a result of a short circuit. The windings are nicknamed the multimeter, repair is carried out.
  • Когда один компрессор нагревается, а другой нет, проблема в автоматике или системе охлаждения «No Frost». The reason can be in the evaporator, relay, thermal attemptor. Diagnosis will help to determine the exact cause.

To cope with a breakdown, watch the video:

To avoid troubles with the refrigerator, as well as to extend its service life will help compliance with the operating rules:

  • Correct placement. It is unacceptable to install equipment near hot batteries, furnaces, close to the walls and furniture.
  • Timely defrosting. In this case, mechanical removal of pieces of ice in the chamber is not allowed.
  • Correct. Overload of the shelves of HO and its doors leads to the rapid wear of details.
  • The temperature of the products. Only cooled dishes can be placed in the refrigerator.
  • Temperature control on the regulator. Do not install the thermostat in the department for the full power for a long time.

If you find a malfunction, do not delay the repair, call a specialist. Now you know what to pay attention to so that the technique has been working uninterruptedly for many years.

Diagnostics of the refrigerator

A thorough examination of the unit helps to identify problem nodes:

  • Be sure to check the main details. Did they have corrosion and other deformations? Whether the protective coatings are broken? Other mechanical damage can also appear with a high probability when the STINOL refrigerator does not freeze.
  • The tightness and strength of the attachment of parts of the structure also deserve a separate analysis, especially if the refrigerator STINOL does not freeze.
  • Of all the properties, there are three main ones. power consumption, temperature in the freezer and near the rear wall of the cabinet. You need to understand whether the replacement of the starting relay of the stinol refrigerator is required.

The seal was dry

Symptoms: the seal on the door dried up, cracked, does not fit tightly. Over time, the door seal is drying out, which is why cold air seeps out: if the disease has gone too far, the compressor has to spend too much time maintaining the required temperature, it overheats, and the protective relay can simply turn it off (or the compressor will even break, which will happen real disaster). If after a visual inspection you noticed problems with the seal, it is better to replace it.

Reliability is a distinctive feature for all refrigerators from this manufacturer included in the lineup. But even in this case, no one gives complete protection against breakdowns during daily operation. It becomes easier to deal with the problem if you know about the causes and consequences from the very beginning. A separate instruction is allocated for the compressor of the stinol refrigerator.

Damage to the cabinet

A thin layer of hoarfrost will appear on a static evaporator if the cabinet is faulty for some time. Because of this, the liquid in large quantities accumulates inside the container.

Because of this, the tightness of the No Frost system is violated, which is caused:

  • Slots that appeared between the rubber seal and the cabinet doors.
  • The appearance of deformations.
  • Torn seal or its loose fit.

A hair dryer for drying and hair styling in 1-1.5 kW will fully cope with the problem if the defect is not very serious. It is enough to act with hot stream in the place where the seal adjacent to other parts of the structure. Then the material is stretched so that its form is adjusted. When the manipulation is finished, the door is closed. If there are tears on the protective layer, the latter is changed so that the freezer continues to work.

Malfunctions of the elements of the electrical and automation

The components of the electric circuit and automatic parts also often lead to breakdowns. You can give the list only the most common:

  • The drainage system was clogged with small particles, after which Stinol’s refrigerators stopped working.
  • The heater of the pallet for the evaporator was broken.
  • Defects appeared in the freezer and timer.
  • A malfunction associated with a thermal.guide or a heating heater.
  • The insulation resistance in the electrical system has decreased.
  • A fan or compressor has broken, other main parts of the system.
  • The launch or thermal relay was faulty, as a result of which the freezer ceases to be valid.

Identification of a defective element and repair are the main actions that are associated with the solution of the problem in this case. If you just do not solve the issue, the detail is simply changed to a new.

Problems with the refrigeor

In the freezer, the temperature level will be less.18 degrees, if the volume of the refrigerant was overestimated when refueling the device. The refrigerator will remain too cold.

Condensate or layer of hoarfrost is covered with a reverse pipe. It is better to adjust the dose of the colad after a two.hour run.in, this helps to cope with problems, for example. if the upper chamber does not freeze.

The refrigerator will remain warm if the liquid dose is, on the contrary, underestimates. The temperature decreases more than 25 degrees below zero. In such a situation, hoarfish often appears on the back walls. It is necessary to adjust the dose until the indicators become normal so that the refrigerators of Stinol immediately start.

Refrigerant leak

The last factor is a consequence of a violation of the operating rules. Experts categorically do not recommend changing the ice with sharp objects or defrost the freezer, placing a tank with hot water in it. Such actions lead to the formation of microcracks, through which Freon gradually seeps.

  • temperature growth in all cameras
  • The motor works without stopping or with short.term pauses between inclusion
  • The compressor does not start, there is no cold in one or in all cameras
  • Illume on the evaporator
  • The capacitor does not heat up

The master with the help of the latest foreign equipment will accurately determine the place of leakage, blow the capillary pipeline, replace the filter-dryer, will vacuum the system and refuel it with high-quality refrigerant.

Features of the refrigerator

The freezer of the STINOL refrigerator is made of polystyrene. The space between the compartments is filled with polyurethane foam for thermal insulation. The capillary pipeline is used as a throttle, which is why the refrigerator is sensitive to changes in humidity and air pollution.

All Stinol refrigerators are divided into evaporative and compressor types. They work as follows: the device uses a substance called a refrigerant for cooling. this is a liquid that evaporates at room temperature.

The process of the refrigerator is as follows: the vapors of the freon (refrigerant) are constantly submitted to the radiator, which is located behind the refrigerator. Then Freon condenses in a radiator, where he gives heat, after which he enters the capillary tube, from where the freon is injected into the evaporator, and then the process is repeated again.

The refrigerator can have one or two compressors, which depends on the model. The compressor is a steel coil, which is recorded by metal plates. The presence of several compressors allow you to separately configure the operation of each refrigerator compartment.

Refrigerators have two types of evaporators:

An important element for the stable operation of the refrigerator is the electric system. It consists of such elements:

  • When voltage is supplied, the current moves from the thermostat to the forced thawing button, then to thermal protection, after to the launch relay and from it enters the motor winding. The current entering it gives voltage higher than necessary, this is because the starting relay works and closes the contacts only with this voltage level.
  • After this, the relay transfers the current to the launch winding, and the engine begins to rotate. The motor works, the refrigerator begins to freeze. When the temperature reaches a given level, the thermostat is turned on. He opens the contacts, stopping the flow of current to the compressor, which is why he stops. The work resumes as soon as the temperature reaches the required level.
  • In case the motor overheats, there is a thermal protection relay. Когда температура становится слишком высокой, специальная деталь на реле − биметаллическая пластинка − выгибается и размыкает контакты, чтобы потом остывший элемент встал обратно и снова замкнул контакты.

Common breakdown of STINOL equipment

The full line of models of the Stinol refrigerated equipment has quite high reliability indicators and is able to work without breakdowns for several years. Nevertheless, these units, like the refrigeration equipment of each other manufacturer, do not have insurance from the sudden occurrence of violations in work, and also have weaknesses.

“Diseases” of the corps

When the steel cabinet of the refrigerator is damaged, a small volume of hoarfrost is formed on the evaporator, which leads to the accumulation of a significant volume of liquid in the container for collecting condensate. This condition is the result of a violation of the tightness of the camera for the following reasons:

  • loose fit or defects (rupture and other) elastic bands of the seal;
  • deformation of the metal case and its parts;
  • gaps between the surfaces of the freezer and sealing elastic band.

So that the sealing gum, when it stretches, return the initial parameters, it can be “pulled” with a low.power hair dryer, with a power of up to 1.5 kW. To do this, warm the elastic of the seal in the place of fit with hot air and pull a little. to restore the original shape of the part. Upon completion of the manipulation of the refrigerated cabinet door, closed. Continue to use the refrigerator is allowed only after the rubber seal is completely cooled. When the protective layer breaks, then it is replaced.

Failure of automation and electrical elements

Often malfunctions occur with components of an electric circuit or automation devices. These include the following:

  • trigger or thermal relay malfunctions.
  • fan, compressor and other component elements;
  • decrease in the insulation resistance of the electrical circuit;
  • defects of the timer and freezer;
  • clogging of the drainage system by particles of food and similar;
  • malfunction of the heater of the evaporator pallet.

The elimination of automation breakdowns in STINOL units is to detect a defective component, repair, and when it is impossible, replacing the element with a new part.

Reflash

Когда превышен объем фреон во время заправки трубопровода. the temperature is less than.18 ̊s, it is cool in the refrigerator compartment, and the return tube is covered with a layer of hoarfrost or covered with condensate. To normalize the functioning of refrigeration equipment, after running in for two hours, the volume of refrigerant is corrected.

Когда дозировка заправки понижена, холодильный агрегат достаточно теплый, а температура понижена свыше, чем на.25̊ p. In the back wall, he is capable of forming. The solution to the problem is similar to what is used with an overstated volume of refrigerant. the dose is adjusted to normal.

Когда наблюдается утечка фреона, в зоне нарушения герметизации трубопровода наблюдаются маслянистые пятна. To eliminate the malfunction, it is necessary to store breakdown and refuel the unit by a refrigerant.

Thermostat problems and their diagnosis

The temperature controller fails quite often and this is the result of the fact that the German.made part from Ranko is designed for operation for five, but not more than 6 years. When the thermostat goes out their system, the compressor also does not turn on and, in order to prevent further malfunctions of other components that begin to occur with a broken thermostat, the temperature controller must be fixed. At home, it is difficult to diagnose the component’s performance, but it is possible. There are two options for checking the working condition of the thermostat:

  • Contacts of the thermostat must be closed, due to this, the continuity of the electric circuit is maintained and energy is supplied to the compressor input in the input. Check. whether the food is present and, when it is not, they call the integrity of the chain completely. from the outlet. When the food is present, it is turned off and nicknamed specific contacts. When they are cut off, the thermostat must be replaced with a new.
  • The input contacts of the thermostat are closed using a jumper (among themselves, a tool with an isolated handle and a conductive working part is used). When the compressor begins to work, this indicates a malfunction of the thermostat. When the compressor does not start, the problem is not in it. The malfunction is also possible to identify “by ear”. during the mechanical turning of the thermostat switch there is a click and when it is not, most likely the thermostat fails.

Each malfunction of the stinol refrigeration equipment, the age of which exceeds 10 years, must be considered by the master. Repair of these units mainly involves the replacement of a faulty part of the working.

What to do if the freezer is defrosted or the summer has “reigned in it”?

As practice shows, most modern Stinol refrigerators are equipped with two compressors engines at once, each of which provides the necessary temperature in one of the chambers.

In the event that the freezer has stopped performing its immediate function, does not freeze, or completely defrosted on its own, there may be 2 reasons: failure of the motor-compressor, or problems with automation. To determine which of the reasons is the most relevant is easy enough.

It is enough to touch both motors with your hand. If both are hot, or very warm, the problem is the motor. Most often, this is an interval closing of windings. If one motor is hot, and the second is cold, the problem is in automation. Most often this problem is found on refrigerators equipped with the No Frost system, which simply fails.

If this is precisely your case, experts strongly recommend contacting a service center where they can conduct a full diagnosis, identify a faulty element of the system and repair. This recommendation is due to the fact that the automatic thawing system itself includes a large number of different parts, each of which can cause a malfunction.

Problems in the No Frost system

One of the last Stinol refrigerators that came off the assembly line in Lipetsk. there were models with the automatic thawing system No Frost. During the operation, the main malfunctions were manifested, which have the following signs:

The freezer is buzzing.

Most likely there were problems with the thawing system, and hoarfrost began to form on the back of the evaporator. A fan that evenly distributes the air inside the freezer begins to rub on a snowy “fur coat”, which causes extraneous sounds. Replacing the heating element of the thawing system in most cases solves this problem.

Inside the refrigerator is noisy, the beating is heard.

In this case, the most likely reason is the breakdown of the fan. Constant rotation leads to the natural wear of the bearing group, the first sign of which are beatings and noise. It is recommended to replace the fan until it completely fails, otherwise there will be no uniform spread of cold air inside the chambers, which can lead to a failure in the operation of electronics.

Leak the refrigerator

If the refrigerator flows from below, then depending on the type of defrosting system, there are different reasons:

  • If the refrigerator Stinol No Frost flows, then the automatic thawing system is most likely out of order. If it is not repaired on time, then in a very nearby compressor will fail due to constant work for wear.
  • In the case of refrigerators from the drip system, there may be several reasons. the condensate container fell, the pipe jumped out or the drain hole was clogged inside the refrigerator. All these malfunctions are eliminated independently without involving specialists.

To get rid of leaks in the stinol refrigerators with a drop system on your own, turn off the technique from the network and expand it with the compressor to yourself. Find and carefully inspect the condensate bowl (white plastic container, which is located on the motor body). If necessary, install it back in place. A pipe of the condensate drain system (black tube of small diameter) should be directed into the bowl).

Make sure that you haven’t jumped out of the tank. After that, examine the refrigerator inside and in the case of clogging the drain hole (is located in the lower part of the posterior wall of the refrigerator), carefully clean it.

Another reason for the leak of the refrigerator, regardless of its defrosting system, may be a long shutdown from the mains, failure of the control module or compressor breakdown. In case of serious malfunctions, it is recommended to contact specialists.

The engineers of our company provide qualified assistance in repairing Stinol refrigerators of all models. Great practical experience and a high level of technical training enables our masters to quickly find the cause of the malfunction and eliminate it at the client’s home without transporting the refrigerator to the service center.

Author

Kerariel

| Denial of responsibility | Contacts |RSS