The machine is erasing but does not drain water

The washing machine does not drain water. what to do?

What to do if the washing machine after washing does not drain water and does not allow the hatch to open? In our practice, this is a very common problem that customers address us. Most often, the repair of this malfunction costs about 3 thousand without taking into account the cost of parts. But is it necessary to call the master? Is it possible to correct a breakdown on your own?

Usually, at the end of the washing program, the water is pumped out and merges into the sewer. However, it may happen that the water does not merge, the linen is not squeezed, and this can be caused by several reasons, which we will talk about in this article. You can eliminate some reasons yourself.

First you need to turn off the machine, turn it off from the network and open the filter lid (located below on the right). To prevent the floor, you can use a rag and scoop or a low basin, there will be a lot of water!

The washing machine does not rinse, does not push up and does not drain the water

Our masters often face this problem. In most cases, the machine starts and begins to wash, and in the middle of the program simply stops. To drain the water, start the “drain and seal” program. If the washing machine does not drain water, check the condition of the drain hose; it can be extended or twisted. If everything is in order on an external sign with the hose, the cause of the malfunction may block the drain or sewage system. Direct the drain hose to the bath and repeat the attempt to start the drain. If dirty water poured, then the problem is in the blockage of the sewer system.

If the machine did not drain the water, it must be turned off from the network and manually drain the water through the filter located below the hatch. There will be a lot of water, so prepare a few containers.

Zasor in the filter

In dirty water, which merges after washing underwear, there is small garbage. dust, crumbs, villi, threads and small objects forgotten in s. So that the garbage does not accumulate in the sewage system, the filter is installed in front of the drain pump. When it is polluted, the water does not go to the sewer system.

The filter is located behind the lid in the front of the lower part of the washing machine. The hatch usually opens with pressing. In its design, the detail is similar to a screwed cork. To extract the filter, it needs to be scrolling counterclockwise. Before removing the filter element under the washing machine, you need to substitute the dishes into which the remaining water will merge after dismantling the element. In modern machines, a “nose” is installed on the filter cover for draining water. In this case, it is better to drain the water through it, and then remove and clean the filter structure.

From a drainage filter, you need to extract accumulated garbage using running water or hard brush. After that, the filter element is installed in the washing machine by twisting by clockwise.

Blocking a filter mesh

The reasons for the lack of rinsing and draining water can be in the suction of the mesh at the end of the filler pipe. In most cases, large particles of garbage, rust and sand accumulate in this place.

The plastic mesh is designed to clean the tap water entering the washing machine. Almost all modern washingrs are equipped with this filter. Before unscrewing the flood hose from the washing machine, it turns off from the network and water supply. After that, manually or pliers are unscrewed by the hose fixer and the net gets. To ensure thorough cleaning, it is recommended to use a brush with a hard pile. With excessive pollution or damage to the grid, it can be replaced with a new. After cleaning, the part is installed in the inlet window. After connecting the intake pipe, the machine is connected to the water supply and its quality of work is checked.

Damage of the pump (drain pump)

If the washing machine does not switch from washing to rinse, in 20% of cases this indicates a breakdown of the drain pump. In this case, seas, rinsing and draining water does not occur. The pump’s impeller is damaged if an extraneous item gets into it. This leads to the fact that the pump is burning out, and the washing machine does not rinse the laundry and does not drain the water. The pumping of the pump is evidenced by the following facts:

• When pouring and draining water, the machine buzzes greatly;
• there is no reaction to programs;
• incomplete volume of incoming water;
• Turning off when filling.

In the machines Virpul, Ariston, Indesite the pump is located below. After removing the rear panel, you can immediately see the part. Initially, it is recommended to check the performance of the impeller. To do this, the drain filter is unscrewed, under which it is located. The impeller is examined for the presence of mechanical damage. If she clogged, then you need to clean it and try to scroll through the impeller. If it is spinning, then the problem is eliminated.

With a complete malfunction of the pump, it is recommended to replace it. In order to avoid inaccuracies when selecting and installing the node, it is recommended to entrust the procedure to the master.

Water sensor is broken

Thanks to the press, the water level in the tank of the washing machine is determined. Washing occurs only when the control board gives a command of the set or drainage of water. The machine begins to rinse the laundry or squeeze it only after receiving the command. When the water level sensor fails, the absence of commands is observed, so the rinse mode does not turn on. You can determine the sensor breakdown by certain violations in the operation of the machine:

• in the tank there is excessively or little water during washing;
• The washing machine turns on the heater when there is no water in it;
• The smell of burning appears and the fuse of the heating element is turned on;
• When the rinse mode is turned on, the water is typed and immediately drains.

If suspicion of a breakdown of the press, you can independently check it out. To do this, you need to unscrew the bolts on the rear panel of the washing and remove it. Pressostat is located on the side wall of the electrical appliance. The connector and hose are disconnected from the sensor. After unscrewing the fasteners, the block is dismantled.

After removing the device, you need to carefully examine its tube and determine external damage or blockage. If they are available, the tube and the fitting are cleaned. There should be no traces of oxidation on external lamellas. Otherwise they are cleaned. A hose in which you need to blow is put on a fittings. If the sensor works, then there should be one or more clicks. Otherwise, the press.steast should be replaced. It is installed in the washing machine in the reverse order.

Action to eliminate the problem

After the water is merged, they begin to search and eliminate the cause of the problem.

To do this, sequentially inspect and clean the nodes of a washing machine as:

• drainage filter (drain) pump, its impeller;
• siphon to which the drain of the machine is connected;
• drain pipe coming from tank to pump;
• water level relay in the tank;
• Management module.

Clean the filter and siphon

To clean the filter, using a screwdriver or knife, the hatch or panel closes it, put a rag on the floor and, unscrewing the lid, remove the filter from the pump, clean it from foreign objects, washed under running water.

To clean the washbasin or washing siphon, to which the sewer sleeve is connected, the following manipulations are performed:

• The hose is disconnected from the pipe on the siphon.
• The lower part is unscrewed from the siphon, removing fat accumulated there from the sump, a vertebrate powder.
• The siphon is unscrewed from the drain of the washbasin (sink).
• Having placed in a bucket or other deep container, the siphon is disassembled, with a thin wire or an old toothbrush, its sump, upper phantry and lower corrugated pipes from fat and dirt are cleaned.

After cleaning, the siphon is installed in place and washed with a stream of running hot water from the tap.

Important! Rinse plastic siphons and sewer pipes from PVC with very hot water (more than 60 70 0C) should not be. under the influence of temperature, their materials are deformed, thereby reducing the internal passage of the sewage system and increasing the risk of blockage.

Check the pipe

When cleaning the filter with a flexible small hose or wire, check the drain pipe.

If a blockage is detected, the pipe is removed from the pump and cleaned. for this, the machine is placed on the side, unscrew it to the bottom, remove the pipe from the pump flange and tank

Pump pooler

At the stage of cleaning the filter, the free pitch of the pump’s impeller is also checked. for this it is groped for with a finger and carefully, without much effort, is rotated.

If the impeller spins quite easily, without jamming, then the pump is serviceable, and its removal and inspection is not required. If the impeller rotates tightly or does not turn out at all, the dismantling and inspection of the pump is necessary.

On a note! In machines with the “drain” mode, the pump’s performance can be checked by starting this mode and observing the speed of rotation of the impeller through the seating site of the drain filter.

When electronics failure and damage to the water level sensor

If, with the manipulations described above, the machine still does not drain water and does not squeeze the laundry, then the reason for this is the breakdown of the press start or electronic control module.

The main breakdowns of the press start are:

• Clogging of the hose and compression chamber. The plug made of powder formed in the hose or compression chamber of the sensor when the water level falls in the tank slows down or completely blocks the closing of the press.start. This leads to the fact that a simple operating system of equipment, without receiving the corresponding signal from the relay, “thinks” that there is water in the typewriter, and does not give the engine a signal for the execution of the Excitement program. You can eliminate these malfunctions by removing and cleaning the hose and the compression camera of the sensor.
• Damage to the hose. When grinding the press start hose, the sensor does not work (there is not enough air pressure to press the diaphragm). As a result of this, the machine can type a lot of water (overflow), without proceeding to washing the laundry loaded into the drum. If such a malfunction is detected, it is eliminated by the replacement of the failed hose with a new.
• Contact oxidation inside the relay. You can eliminate this malfunction by removing the relay nutrition chip. The trace of the oxide is recommended to be removed with a knife or flat screwdriver.

The main damage to the electronic control module is the failure of its components. resistors, small capacitors, controller.

Their selection and replacement of experienced craftsmen-electrons. In most cases, a malfunction of this module leads to its replacement.

Read more, the washing machine does not warm the water when washing: the reasons and their elimination, why it heats up for a long time

Pressostat

Pressostat or water level sensor is provided in the design in order to control the level of filling the tank. It is he who regulates the work of the intake valve, commands the beginning and end of the liquid set. The mechanism provides for the presence of a water column. Pressure in it shows how the tank was filled.

Most often, a special pressure tube is out of order, since small garbage, sediment, scale can fall into it. As a result of this, the press.steast transfers erroneous data to the electronic module, and the device begins to work incorrectly. Another reason for the breakdown lurk in the hoses and shutters of the sensor. Blockage are possible, as well as air leakage. These troubles also cause an incorrect reaction of the press, which is why the washing machine picks up water and immediately drains.

Regardless of the source of problems, the first thing is to make sure that this component is the fault of the washing of the washing room:

• It is necessary to turn off the equipment, pull the fork out of the outlet and remove the top cover of the case. For this, the bolts are unscrewed, and the lid itself is shifted to the side and removed.
• Pressostat is usually attached to the wall of the device using a pair of bolts. To correctly disconnect it, you need not only to unscrew these bolts, but also to unscrew a small hose, as well as contacts.
• Now the sensor can be checked using a short tube. It is important that its diameter corresponds to the original tube of the mechanism. After connecting the tube, you need to blow into it, while listening to the device. Sounds like clicks indicate full performance, and their absence suggests that it was time to replace the press.

If the device tube is clogged or deteriorated or contacts look improperly. these problems are solved easily. In other cases, the sensor must be replaced.

Causes and signs of a malfunction

How the user can understand that there was a malfunction:

• Pay attention to the first signs of a breakdown. For example, water merges slower than usual.
• The washing machine does not drain water at all.
• The washing cycle takes place as usual, but when it reaches the drain, the system freezes.
• The machine drains water through one wash.
• After draining the seas does not begin.
• After the main washing, the water merges, after rinsing. no.

You can also notice a loud noise: the car will buzz, as if draining the spent water.

• The wrong regime is set.
• The drain pipe, hose, sewage.
• The pressure sensor failed.
• The drain pump broke.
• The electronic board burned out.

Possible reasons, verification and elimination

Before any repair manipulations, you should remove all the water from the drum, remove the linen and turn off the device from the network.

Remove the protective panel under the pump, remove the filter, evaluate its condition.

Sometimes the blockage does not occur in the filter, but in the pipe located behind it.

Rinse the filter under a stream of warm water, remove large garbage

The pump works on the pump. If it breaks, when the machine is turned on in this part there will be silence

The pump is actually cannot be repaired, it is changed to a new.

The failure in the washing program is monitored by error code. It is displayed on the device panel, in different models it may differ

Repair or replacement of an electronic module. Read how to replace the module yourself

Can be tracked even at the stage of the water bay in the drum. The sensor does not track the amount of the fence and does not determine that the liquid is enough

If you need spare parts for self.repairs, purchase them from us: a broadest assortment, fast delivery in Russia and a guarantee for everything.

Washing machine operating rules

In order for the technique to work without failures, you need to handle it correctly:

• Each model has a certain bootable linen limit. If you exceed it, the unit will “work for wear”, which will significantly increase the risk of problems. Strictly observe the established standards;
• Before washing clothes, carefully check your s and accessories. They can provoke violations in the work of the impeller, pump or engine;
• To connect the washing machine to the mains, use the network filter if possible. He will protect the technique from voltage drops;
• Clean the drain filter regularly;
• select the correct washing program;
• Each year, carry out preventive cleaning of a car without linen. with the help of washing powder and a special tool that removes the scale.

Observe simple operating rules, then the equipment will work without failures, and washing will always be in joy

Careful attitude and compliance with the rules will significantly increase the life of the washing machine.

The reasons for the refusal of the drain

Attention! There are washing machines equipped with a display on which an error code is displayed. In such cases, diagnosis is much easier. Devices are also produced without automatic spin, and the command is given in addition after the washing room stops.

What to do in case of malfunctions in the elements of the device?

If a breakdown is detected in a washing machine, it is necessary to turn it off from the network and independently drain the water remaining in the tank. This can be done in several ways:

• через сливной шлаг, расположив его ниже уровня бака и опустив внешним концом в подготовленную емкость;
• By unscrewing the drain filter in the lower front of the device (it is important to lift the edge of the machine a little and slip a water vessel under it);
• through the emergency drain hose of smaller diameter, stretching it and removing the plug (this hose is located near the filter at the bottom of the device);
• Disconnecting the drain pipe located under the drum inside the device case (this method is quite laborious, requires accuracy and competent handling skills);
• Having opened the door of the machine and manually erasing the water from the drum (this method is not suitable for machines, in which the hatch door remains locked even after disconnecting the unit from the network).

You can drain water from the washing machine using an emergency hose

Below we have brought a list of internal elements of the device, when problems with which problems with draining will be observed in the washing machine. Some of the defects can be handled independently, in other cases, the help of a qualified specialist will be required. The reason that the washing machine does not pump out water may be malfunctions in the following details:

• Drill hose. It often happens that the hose is pushed, twisted or incorrectly installed. In this case, the water pumped out of the tank simply cannot overcome a mechanical obstacle and remains in the machine. The same applies to blockages in the hose. Explore the element, make sure that it has sufficient clearance and nothing interferes with the free current of water. First, inspect the hose from the outside, and then check its patency from the inside.
• Filter. This part, as we previously wrote, is located in the lower part of the machine body from its front side. Most often, the filter turns out to be clogged with small objects like bones from a bra, coins, buttons and pins. The blockage must be eliminated, and the filter itself is washed and gently put in place. If the problem was only in the clogged filter, then after the manipulations, the water should freely leave the tank.
• Pipe branch. The pipe connects the battery of the washing machine with the pump (pomp). If the blockage occurs in this part of the device, it is necessary to open the body of the device and unscrew the bolts fixing the mounting mounts of the drain. Next, remove the pipe, removed a fixing clamp and drain the water from the part to a pre.prepared container. After check if the pipe is clogged with some kind of garbage. When you find a blockage, remove it, and then return the entire structure to its original state.
• Impeller. Sometimes the pump’s impeller can jam if even a small foreign object gets inside. It is located immediately behind the filter and normally rotates freely during the operation of the pump, exposing the water from the drum to the sewer. Try to twist the impeller with your hands. if the part is spinning with difficulty, it means that an extraneous object fell into it (most often threads or piles). The blockage must be removed. By the way, the malfunctions in the work of this part can be detected by a characteristic sound: the machine is quietly buzzing when draining water, since the impeller blades cannot rotate fully.
• water pump. If the impeller rotates, but the pump does not drain water, then the breakdown occurred in the most drain pump. In this case, only the complete replacement of the part can help.
• Water level sensor. Normally, the press starts the water level in the tank. If the sensor is broken, then a signal is received in the control module that all the water is already merged, which means that the washing process can be completed. Faulty press starting should be replaced. You can do this yourself or by contacting the center for repairing household appliances.
• Management module. If this part is out of order, then the signal from the device board does not enter the motor, the pump does not turn on, which is why the water does not leave the drum. It is almost unrealistic to fix the control unit independently. the typewriter requires a full repair or even a complete replacement of the part.
• Wiring. In the process of finding the causes of malfunctions with the drain system, pay due attention to checking the integrity of the wiring of your device. In some cases, incorrect operation of the drain pump may be caused by the absence of sufficient supply voltage on the pump.

Drown of the drain pump can cause problems with draining

If you decide to take up the repair of the machine yourself, be extremely careful: unprofessional actions of users can lead to faults, the elimination of which will cost many times more expensive. In any case, at home, you can try to determine the nature of the breakdown. It is likely that the reason for the problem is extremely simple and it will not be difficult to get rid of it on your own.