Causes of malfunction
Sometimes it happens that the washer collects water, but does not carry out its direct purpose. If this happens, then do not immediately panic. Often the problem can be solved without going to the service center. Let’s look at the causes of such a malfunction:
- The drive belt can come off.
- Malfunctioning motor.
- The heater burned out, consequently, the water does not warm up and washing does not start.
- The failure occurred in the control board. It happens quite seldom, but it cannot be ruled out.
Faulty valve
In the liquid supply line of the equipment is a valve with a spring-loaded membrane, which is controlled by an electromagnet. If the washing machine draws water when turned off, it is necessary to check the condition of the unit. You need to remove the valve block and inspect the channels, removing dirt deposits. If it was not possible to restore the operability of the construction, it will be necessary to replace the valve. Keep in mind that damage to the solenoid coil disrupts the normal operation of the valve, and it is impossible to determine the defect visually.
There were cases when the valve spring lost its elasticity and the machine began to bleed water during the washing or stopped due to faulty signals from electronic sensors. To access the valve block, you will need to disconnect power to the equipment and remove the supply and drain hoses. Inlet valve is at the point of connection of the water main, to access to the part you will need to remove the upper or rear wall of the housing (depending on the design features of the equipment).
Disconnect the valve body from the water supply hoses, de-energize the solenoid coil power cables. Tubes are fixed on the valve with the help of spring clamps which can be removed with pliers or special tool. The new valve is installed in the same position as the old unit. After repairing the machine should be tested.
Why the washing machine fills the water, but does not wash: the main causes of failure
If you have skills in this matter, it is not necessary to call a specialist, you can remove the problems yourself. When there is a problem with the water level sensor, you need to remember that it is located on the wall of the washing machine at the back (if the load is horizontal). In order to get to it, remove the lid, and if notice oxidation of contacts, they are carefully cleaned.

If the pressure tube is clogged, clean it. And if there are cracks on it, seal it by using epoxy glue or cold welding. If after these measures nothing has changed for the better, then replace the sensor with a new one.
If the outlet valve is malfunctioning, water sometimes rushes into the appliance and comes out of the appliance quickly. This is because the pressostat can regulate the required volume of liquid in the household appliance and at the same time does not allow it to have “extra” water. If the membrane is broken, the liquid does not come out much. And if the outlet valve is broken, the water cannot be shut off in time.
It should be remembered that when a washing machine malfunctions, in which it constantly draws and drains water, not only can come a large utility bill (water supply), but also there is a heavy load on the heating element, since it is constantly on to heat the contents of the household appliance. From this can quickly appear scale, and it will affect not only the nodes of the unit, but also the heating element. Sometimes in the case of overfilling, the protection does not work and then you can flood the neighbors
Therefore, it is very important to notice malfunctions in time and, if necessary, call a specialist who will fix them in a matter of hours
Frequent Ardo malfunctions
Ardo washing machine can stop with a full tank at any time. Such a breakdown occurs both in newly purchased models, and in already working machines. Improper installation, abnormal operating conditions and natural wear and tear of the parts cause problems with the program start. It depends on the brand of washing machine, the situation and the “symptoms”.
Modern Ardo washing machines are capable of self-detection of a breakdown thanks to the self-diagnostic system.
As a rule, braking before starting signals a malfunction in four places:
- drive belt;
- electric motor;
- the drum;
- control board.
It is next to impossible to tell at a glance where the fault is. Only the self-diagnostic system, which automatically scans the nodes and narrows the search field with an error code, will be a salvation. Without this function, you have to be “blind”. check every possible place of failure one after the other.

Problems with the drive
Candy washing machine can draw water and not start because of problems with the drive. Most often, belt stretching is provoked by the constant overloading of the machine. If you put more laundry in the dispenser than allowed, the rubber band will eventually wear out. As a result, the technique will not be able to spin the drum, and, consequently, and wash things.
Belt drive on “front” washing machines is behind back wall, on “vertical”. behind side panel.

To remove the wall and gain access to the belt, it is necessary to unscrew all the screws fixing the panel. A screwdriver is needed for this.
“Jumped” belt should be inspected. Cracks or small tears can cause it to fly off the pulley. The worn rubber should be replaced. To tension the new drive belt, first pull it over the engine pulley. Next, put the rubber band on the larger “wheel” and crank it from right to left. This is how the strap “sits” in its place.
Trouble in control box
If all the above actions did not allow to restore performance, it is necessary to inspect the controller. Damaged electronic elements or harnesses cause the washing machine to draw water and not wash the loaded laundry. The causes of failure may be caused by voltage fluctuations or water on the contact pads. Repair of the control unit is made in the service center, if it is impossible to restore the printed circuit board, then you will need to buy a new controller (or a used one, removed from the disassembled equipment).
Washer draws water but does not wash
An automatic washing machine is a complicated appliance that may malfunction. And it happens sometimes at the most inappropriate moment. What to do if the machine takes in water for washing, but after that process doesn’t start, why the machine doesn’t wash? Such a problem is not uncommon, and the causes may be different.
Causes of failure
If the washing machine draws water, but further does not work, it does not mean that it has to be thrown out. Some of the causes of this failure can be eliminated with your own hands. So, what can happen, why the washing does not start?
- The drive belt has come off (if there is such at all).
- The electric motor has malfunctioned, so the drum does not rotate.
- The heating element is burned out, which means that the water is not heated. the washing does not start.
- Malfunction in control board (happens rarely).
Possible causes
Such defects occur due to three obvious reasons: wrong transportation of equipment, mistakes during installation and connection, and gross violation of operating conditions. This can also include the natural wear and tear of individual parts or an entire group of elements.
- Belt has come loose;
- Centrifuge jammed;
- Bearing blockage;
- Problems with the motor;
- Breakage of the main board;
- Heater element failure.
It is also a good idea to check the external and internal hoses for physical damage and blockages.
Belt
Most often the belt comes off due to the increased load on the centrifuge. If the laundry compartment is clogged, the pulley will crank the teeth on the belt. As a result, they wear out, the tension loosens, and the drum rotates more slowly, jerkily, or stops rotating at all.
Centrifuge wedge
It may happen that in the gap between the tank and the centrifuge foreign objects fall: unscrewed bolts, clamps, loose hose or, for example, a large button. In this case, the drum clicks and the motor runs with tension and hums. If you get rid of the cause of the wedge, everything should start working normally.
Foreign objects inside the tank may be the cause of the malfunction
Bearings
If you hear a rattle and a bang during the washing process, then the bearings are most likely out of order. When blocked, the internal elements begin to spill out into the housing and rattle. Do not delay with the repair, because a damaged bearing will pull the belt and drum axle. How to replace a bearing, read here.
Engine
On modern washing machines, problems with the motor arise due to wear and tear of the brushes. While on the asynchronous solutions there is a loss of capacitor capacity. Both can be replaced, and the motor itself can be rewound.
Carbon brushes wear out over time and need to be replaced
Main board
The problem can be detected by visual inspection of the main board. Blackened contacts or entire groups of contacts indicate the need for service or complete replacement of the module. Specialists strongly recommend not to do self-repair. Otherwise it may burn out the other electronic elements of the washing machine, and subsequent maintenance will cost a lot of money.
The washing machine may not start due to a burned heater element. Its functionality can be easily checked with a multimeter. TEN also does not heat water because of the large amount of scale: take out the part, clean it and put it back.
Pressostat
The malfunction appears in two extremes: the pressostat either overflows or underflows. As a result, the safety systems are activated and the appliance refuses to operate. Checking the pressostat and repairing or replacing it will solve the problem. A similar situation occurs when the inlet valve is broken.
Impeller clogging
The presence of foreign objects in the impeller makes it difficult or even blocks its operation. Because of weak and/or broken insulation, buttons, coins, hair and other undesirable elements may be inside. The solution is simple: open the housing, clean the impeller from foreign objects and after reassembly try to run any washing mode. It is worth checking and cleaning the mating tubes in the same way.
Objects often fall into the impeller as well
Wiring
If after the water intake the machine drum stops abruptly, and the display starts flashing or completely goes out, the cause may be in faulty wiring. To find burned out wires, as well as to eliminate the short circuit will help visual inspection with testing of the main elements of the circuit.
FREE FIX. Washing Machine Fills Then Stops. New Style Lid Switch ByPass #Hack
Semiautomatic
Classic washing machines do everything automatically. But some machines require user participation to switch to a certain mode, for example, spinning. If there is enough water, but required mode is not activated, it has to be activated manually. Such operating conditions should be specified in the instruction manual for the appliance.
Other reasons
Sometimes air enters the pump and the machine refuses to start some modes. It is necessary to purge the system and try to arrange its tightness. Also, it is not worth much to extend the drain hose. The standard output should not exceed 150 cm, otherwise the pump will not be able to perform a full pumping cycle.
Excessive lengthening of the drain hose leads to errors in the operation of the washing machine
It is worthwhile to check all pipes and hoses for twisting. Besides the fact that clamped outlet prevents the flow of fluid, and also on the insulation can be cracked, and it leaks, and as a consequence. increased time of water intake into the system.