The freezer is freezing from above and there is no from below

The top of the refrigerator does not work

Sometimes a household refrigerator becomes a real “headache” for the owner. Extraneous noises, incorrect temperature regime, does not freeze, does not work how to do it and what to do?

Any breakdown is certainly unpleasant and troublesome. Do not despair and give up, but it is necessary to thoroughly figure it out.

Let’s talk about the following problem: the upper chamber of the refrigerator does not work. This is one of the most common malfunctions that many owners of household refrigerators face during operation.

Most modern refrigerators are two-chamber models with the upper or lower arrangement of the freezer, one- or two-compressor. Consequently, the upper chamber of the refrigerator can be either a refrigerator directly or freezer with its own evaporator, in some models. with an independent compressor. It all depends on the modification and configuration of a particular model of the refrigerator.

Therefore, when we say that the upper chamber of the refrigerator does not work, it is necessary to clarify, refrigerator or freezer, as well as other data about the refrigerator. This will help to identify the cause of the breakdown and determine the specifics of the future repairs.

The reasons for this breakdown can be different. It all depends on the technical features of a particular refrigerator model. Here are the most likely reasons:

The following refrigerators are found in the following refrigerators: Atlant, Zanussi, Samsung, Stinol, Whirlpool, Liebherr and others.

It is difficult to determine the exact cause of the breakdown. Many mistakenly trust the advice of forums and acquaintances, independently look for ways to eliminate problems. Remember that with a non.working camera the refrigerator has to work for wear, the system is overloaded. Therefore, it is important to immediately contact specialists and use them to solve the issues of breakdown.

You can independently perform a number of simple actions that will help determine the complexity of the breakdown:

If, after the actions performed, the upper chamber remained in non.working mode, then it is necessary to solve the problem with the help of specialists: diagnostics and repair. You may need to replace the thermostat, refueling by a refrigerant, eliminate blockage or replacement of the compressor. It all depends on the complexity of the breakdown that the master will reveal during the diagnosis.

The situation when the refrigerator broke is always unexpected and unpleasant. Especially on the eve of a large feast or in great heat, when it is necessary to carefully monitor the freshness of the products. Often users are faced with a different problem when the freezer works, and the refrigerator practically does not cool. How to determine the cause?

Why does the refrigerator cool poorly?

Such a breakdown is rarely seen immediately, since the indicators of the serviceability are not indicators on the thermometer in the refrigerator, but the freezer, which continues to work well. The difference of several degrees is difficult to feel a simple person, but the products in the refrigerator spoil literally before our eyes.

If a malfunction is detected, you need to find out the reason as quickly as possible why the refrigerator does not freeze. Setting up the repair will entail a full failure, and then the owner will have to be pretty to spend money on repairs if he is generally possible.

Here is a list of possible reasons why the refrigerator stopped freezing:

• Quiet closure of the door. Perhaps an extraneous object fell under the gum of the door, which interferes with the sealed door slamming. Check not only its absence, but also the integrity of the protective gum. Punctures, breaks or peeling contributes to the output of cold air out;
• High temperature in the room. characteristic of single.chamber models. If the refrigerator is near the hot battery or the room is very warm, and the freezer is tuned for maximum freezing, the power engine does not cope with a high load. Try to choose a more sparing mode of operation. Complete defrosting for at least 10 hours will not hurt. After that, re.set the desired temperature and turn on the device. Do not forget about the thermal insulation of batteries near the refrigerator.
• Another reason why the refrigerator does not cold is damage to metal cooling elements and a freon leak. This could happen if during defrosting you removed ice from a cooling grill with a knife or other metal objects. In this situation, you can not do without the help of a qualified master. But you can solve the problem without tremendous costs. It will be necessary to seal the damaged area of ​​the cooling element and re.fill the system with freon. If you do not want the refrigerator to stop freezing, never force ice exfoliation when defrosting. It is better to wait for complete thawing and then easily remove the lagging ice.

The described breakdowns are characteristic of both single.chamber and two.chamber refrigerators. Basically, such a failure is associated with improper operation, non.compliance with sanitary standards of use and can be independently diagnosed and prevented.

But it happens that the refrigerator does not cold, although all the norms are observed and there are no visible reasons for the malfunction. In this case, you need to more carefully inspect the electrical appliance and analyze its work. Most likely, it will not be possible to repair at home without a master, but you can evaluate the cost and duration of the upcoming repair.

The refrigerator does not work, but the freezer works. the main reasons and ways of solving

Before talking about the causes of problems, you need to make out errors. If you interrogate people, most will say about:

Yes, because of this, the refrigerator can work worse. But to get out of order, you need some reason. And these four options are not that. They can lead to worse freezing or short.term malfunctions, but not disconnecting. Когда холодильник работает, а морозилка нет – поломки нужно искать в других местах.

The simplest problems

Incorrect connection, gaps of wires, installation in the wrong place, sockets. All this can lead to the fact that the refrigerator will stop working at one point. It’s not as scary as it might seem. You can fix small malfunctions with the defrosting of the refrigerator. It turns off from food, all products are removed, and after that day you need to carry out with the refrigerator turned off. After complete defrosting, it can be turned on.

Incorrect installation or error with choosing a place can lead to the fact that the refrigerator chamber starts to work worse over time. This is a cumulative effect. At first it is imperceptible, but then more and more. the temperature will be higher, and the products spoil faster.

To avoid this, you need to carefully read the instruction manual. It will be written there that you can not put the device tightly to the wall, there should be a small gap. Heating sources, like a slab or battery, should not be nearby. Then there will be no problems. If the problem is not corrected by defrosting, you need to look for the reason in another place.

Problems in conducting systems

Problems in the drainage or capillary system. If you do not clean them, a small product, butter or something like that can get there. What will happen next: the freezer works, ice is formed, nothing affects the products. The refrigerator stops working, the temperature inside becomes room.

The drainage system can be cleaned independently. With capillary is more difficult. Can help, but if it does not work, it is better to call the master. He will do everything so that then there are no problems.

Breakage in the capillary system can be confused with the failure of other systems. You need to check the temperature in the “condenser-compressor” section. If it is higher than it should be, and thawing occurs faster than cooling, the problem is in the capillary system.

Automation and electronics

Automation and electronics make the refrigerator more conveniently. To adjust the temperature and turn on non-standard functions, you can press one or two buttons. But, at the same time, electronics more often break. Due to frequent use, they can seize or fail the buttons on the front panel. This is the most common cause of breakdowns. it is impossible to configure the mode, which means that the refrigerator works with failures. It is decided by the replacement of these buttons.

The second reason is the temperature sensor. He may fail or initially be marriage. At first, this is not noticeable, since the compressor works uninterruptedly. But due to the fact that the detector is out of order, he transfers incorrect data. So, the compressor works at the limit of power, which leads to wear.

The master can advise replacing the compressor, but this will not solve the main problem. 5-6 months or a year will pass, but it will fail again. You need to replace the sensor, and then the root cause will be fixed. It is not recommended to independently engage in automation and electronics. For this you need a master who understands modern refrigerators.

Refrigerant leak

A refrigerator enters the refrigerator through the system of tubes. He additionally cools the temperature and works with the compressor. If the refrigerator is not closed, ice forms on the tubes. To speed up the defrosting, people knock it down with hard objects, which leads to microdistributions.

This, in turn, leads to a refrigerant leak. He goes out through the holes and does not cool the system. The compressor begins to increase power to achieve the desired temperature. Ultimately, everything is out of order. To avoid this problem, you need to perform two things: defrost the refrigerator without knocking out the ice, and season with a refrigerant.

Compressor breakdown

When the compressor starts, and after that it stops working, it means that it has failed. If there are two of them in the refrigerator, then the freezer will work, as before. You can try to fix the compressor, but it will cost more than the standard replacement. It is recommended not to change this part independently. Incorrect connection may not only not give an effect, but also damage electronics. It is recommended to contact the master.

Wear of the sealing gum

The gum on the door allows you to close the refrigerator more tightly, and avoid cold air leakage. If this happens, the compressor will compensate for the lack of cold temperature and work faster. What will come of it. overload and failure.

It will be more effective to change the gum. If there is no such possibility. it can be removed, soaked in boiling water and put again in the same place. So it will last another 2-3 years. If the problem is not in the elastic band, but in the places of fastening. they need to be tightened. In order to replace the sealing elastic band, special skills do not need. It is enough to remove it and install a new. Intuitively understandable.

Mechanical and chemical damage

With improper transportation, cracks may occur. If they do not notice them at once. at first there will be no problems. The refrigerator will work stably, as should. But the temperature inside will gradually be higher.

As the compressor is wear, it will give less and less cold, therefore, heat will increase. Due to damage and warm air, the temperature inside will be higher than should be. And the reboot will no longer fix anything. Ultimately the refrigerator will fail.

Small injuries and cracks can be corrected independently. disconnected the damaged part, pour it with foam or replace and cover with foil. If the hole is large and arose during transportation, contacting the store will not help only if the employees were not mistaken.

If the problem was before that, you can submit an application for a return or replacement to the store. When the breakdown formed after the end of the warranty period. only closing holes.

Oxidation and rust on the pipes

Oxidation and rust on the tubes constantly arise. This is due to the fact that moisture particles fall on them, and over time they begin to be covered with rust. No one is safe from this, especially if you do not clean the moisture or quickly close the door.

Rules for the operation of refrigerators

The first thing to consider is the installation site. The risk of 50 % of the breakdowns and the efficiency of the device depends on this. You can not put the refrigerator in a place with a high temperature and next to a direct heat source. Stove, battery. all this should be on the other end of the room. It is advisable not to put the refrigerator in the room, but only in the kitchen, where the temperature will be below.

Modern refrigerators do not need to be defrosting. old models. yes. Everything is pulled out once a year, and for 8-10 hours the refrigerator is de-energized. This will allow you to remove ice from the freezer and the main problems of the refrigeration chamber.

After disconnecting the refrigerator from the power supply, you need to wait 5-7 minutes. After defrosting. one cycle of work without loading products. Work cycle. time between how it begins to make sounds.

The temperature above or below the center of the scale practically does not affect the safety of products. But the engine loads more strongly, which, ultimately, will lead to overload and failure. The middle of the scale is the desired indicator.

The “Fast Froth” button should not be used without the need. So the “contacts” are shorting, and the engine begins to work without a break. After freezing the products, the button needs to be turned off, otherwise everything will fail in the day.

Most of the problems described above are a chain reaction. First, a small breakdown that is not noticeable. Then. deterioration of the system and increased load on the compressor. Ultimately. shutdown and expensive repair. To avoid this, you need to fulfill all the requirements.

It does not hurt to read the instructions. There can be a lot of useless information, but the main features of operation and the use of buttons are spelled out. Usually add typical malfunctions and ways to solve them.

Freezer does not work

Symptoms: in the freezer and refrigerator chambers, a high temperature and a compressor that basket works hard.

If problems arise in the freezer, then they often apply to the refrigerator: Freon first enters the freezer, and if it does not freeze, then most likely there will be the same thing in the refrigerator.

Possible causes of a non-working freezer chamber, in general, are the same as for a refrigerator: see the section “The freezer works, refrigerator. No “on the same page.

Primary diagnosis

Often, something in the refrigerator does not work for the most ordinary reasons, which you can eliminate yourself. from them and start.

The “snowy fur coat” rushed

Everything is clear here: you forgot about the freezer and it all overgrown with ice: cook rags and defrost the refrigerator.

The ice blocked the sensors

One of the consequences of the overgrown “snowy fur coat” may be a blocking of temperature sensors located inside the camera: in this case, they transmit incorrect information to the control module, and the latter submits incorrect commands to compressors.

The temperature is incorrectly selected

It is possible that you set too high temperature in the chamber, which is why the products there began to quickly deteriorate. It is difficult to advise something here: select the correct temperature experimentally, and do not forget that different products require different cooling for their preservation. Do not put too high temperature in an attempt to save on electricity: you will lose more on spoiled products.

The refrigerator is overloaded

When there are too many products in the refrigerator, and if they also block the fan, the compressor may not cope with their cooling. Unload a little refrigerator, redistribute the products so that the fan is free.

The refrigerator is incorrectly installed

If the refrigerator was put by someone with crooked hands, ignoring the obvious requirements for installation, it will very soon affect the quality of the refrigerator. For example, it may not be installed quite smoothly, which is why the door is overwhelmed and warm air from the room gets into the refrigerator. Or something interferes with the tight closure of the door. By the way, and you yourself could forget to close the door tightly: do not be lazy, check again. Naturally, you need to make sure that the refrigerator should not be too close to devices that release a lot of heat, or under direct sunlight. We must also check that the gap between the walls of the refrigerator and the objects standing nearby are not too small.

Problems with electrical wiring

Sometimes it happens that an incorrect voltage is supplied to the refrigerator due to poor contact between the fork and the outlet: the case is rare, but for your own calm, it will not hurt to check.

The fan is faulty

It’s simple to check this: look into the refrigerator and watch the fan: if it does not turn on for a long time, then you have more a problem; You can just listen: when working, the fan motor makes a characteristic sound. However, it often happens that the fan is simply freezing. If after defrosting the fan does not spin. Call the master.

Freon leak

Check the back of the case: if traces of corrosion are visible there, this means Freon’s leakage. Most often this problem is found in refrigerators with the lower freezer. It is better to call a specialist who will provide the necessary sealing and refill the freon.

“Eternal defrosting”

A completely anecdotal case: “flooded” defrosting button. Carefully inspect it, and if you notice that the button is skewed and clamped in the wrong position, squeeze it out, after which you still figure it out why it happened so. maybe some kind of breakdown or constructive defect. Well, or you yourself just forgot to turn it off: the business is everyday. happens. The same applies to the “Vacation” button, which you did not disable after returning from your vacation.

Capillary tube

This part is in the evaporator circuit. If foreign substances have penetrated inside, then the freezer will function, and the refrigerator compartment does not. As a rule, chips or oil penetrate the pipe. As a result, Freon cannot work, and therefore it does not reach the freezer. If the cause of the defect lies precisely in this, then it is urgent to call the master so that there is no breakdown due to the load.

Some owners cope with the problem on their own by tapping capillary tubes for knocking out garbage. In some cases, it saves. But the master cleans the capillary system, changes the filter, vacuum evaporation systems and refueling the refrigerator by freon.

temperature sensor

Many problems can have a two.chamber refrigerator “Atlant”. Refrigerator does not work? This is often due to water and products from the case. Often a temperature defect is associated with factory marriage. over, it does not appear immediately, but after a while.

If the cause of the equipment breakdown in the sensor malfunction, then the installation of a new device is necessary. Repair should be carried out as soon as possible, because due to the intensity of the compressor operation, the operation of the device is reduced. The equipment replacement procedure will not take much time.

Why in a two.chamber refrigerator the freezer does not work

If you have a two-chamber refrigerator “Indesit” (Indesit), “Ariston” or “Atlant”, the freezer in it may not work not only for objective reasons, but due to careless use. Check such moments before sound the alarm and cause a specialist:

• Thermostat. It is worth installing the selector wheel between the 3-4 or 2-3 marks so that excessive load is not created on the compressor. When the mark is higher, the motor does not have time to cool both cameras, so the freezer and it offends to work.
• The density of the fit of the sealing gum. If the door is closed loosely, then snow or ice is growing in the freezer compartment due to the constant receipt of unkiting air flows from the outside. When “rest” the motor is melting, and the melted water flows to the floor. In this case, you need to defrost the refrigerator and carry out minor repairs of the seal in those places where it leaves.

If in your refrigerator LG (LG), “Stinol”, “Ariston” or in any other there is no “fur coat” and the value of the thermostat is correctly set, but the freezer still does not freeze, then there is a breakdown.

The most likely reasons for the malfunction of the freezer

There are breakdowns connected directly with the fact that the freezer department is turned off. Knowing their symptoms and signs, you can easily diagnose a failure and save on the initial diagnosis.

All possible reasons for the failure of the freezer in the Bosch (Bosch), Samsung, Whirlpool, Liebherr (Liebherr), Minsk and others are collected in the table below.

The compressor is broken up for the operation of the freezer compartment.

The air sensor of the freezer broke.

The thermostat of the freezer was broken.

In models equipped with one compressor, the No Frost system and a “crying” type evaporator, a switching valve may break.

The leakage of the refrigerant in the area of ​​the steel circuit is not excluded.

In models with a lower freezer and an evaporator of a “crying” type, this problem is not uncommon. It is provoked by blocks of the drainage hole, due to which the water accumulates in the main chamber and flows into the lower compartment area.

Acting inadvertently in the hope of quickly defrosting the refrigerator, you can pierce the camera, which will cause the inevitable leakage of the refrigerant from the system.

Most likely, the control module broke.

Do I need to care for the freezer? Definitely necessary! Even if you bought the No Frost model, it also needs to be defrosting-not as frequent as a drip refrigerator, but at least 2-3 times a year. It is also worth periodically wipe the walls and containers, inspect the camera at the time of freezing, throw out extra products. In the summer, slightly reduce the temperature so that the compressor does not overwhelm. And most importantly: if you are a “frost lover” for the winter, freeze fruits and vegetables in batches, never load the camera completely.

Now you know for what reasons the freezer of your two.chamber refrigerator may not work. If you have a single.chamber model, a separately freezer compartment cannot fail, since these chambers have a common system.

Using our table, determine why there was a breakdown to know for what repair to prepare-small or capital. And if the thermostat or sensor can be replaced with your own hands, then works such as replacing the compressor or refueling of the freon require special equipment and experience. Therefore, we recommend that complex tasks be entrusted to the master.

Reasons why the freezer does not freeze

Find out why any technique has broken, usually start with food checking. Sometimes the reason that the refrigerator does not freeze products is a banal damage to the cable or even the absence of electricity on the network or a specific outlet.

But, if the freezer has stopped freezing with a normally functioning refrigeration compartment, the problem is it precisely in it.

Last ice and snow or, conversely, their number of them may turn out to be signs of a compressor breakdown, clogged tubes and even a refrigerant leakage.

The simplest problems of the unit

Among the reasons for the freezers of the freezer, a loose door is often found, due to which air enters the chamber.

The refrigerators have a hotpone Ariston, a problem can occur after a long work without planned defrosting. Иногда камера бывает слишком сильно набита продуктами, и техника не справляется со своей задачей.

All these issues are solved simply, without demanding the call of the master. In the first case, the problem with a poorly closing door should be solved. In the second. to defrost the equipment, turning it off from the network, in the third. to reduce the degree of filling the camera so that there is free space.

Breakdown in conducting systems

The technique can work incorrectly due to congestion in the capillary system. Nutrients fall into the tubes. sorcini from a worn filter, oil, moisture. Because of this, the cooler in the refrigerators of such a brand as LG does not reach the right place and the products do not freeze.

Congestion do not pass melt water, which accumulates at the bottom of the freezer and flows out. The result is cracked plastic, corrosion of metal elements, due to which the refrigerant flows out.

Problems with automation and electronics

In the freezers of models of any brand, including Liebherr, there is a temperature sensor responsible for maintaining the desired temperature. If it is broken, the products will be frozen incorrectly.

A sign of the problem-a big break in the compressor due to the data incorrectly transmitted by electronics.

Incorrect frost can be a sign of broken mechanical devices or buttons. The STINOL 106 model often has a problem with a timer set in thawing mode. To solve it, there is enough rotation of the regulator by several degrees.

Refrigerant leakage from the system

The freezer of models such as Indesit SFR 167 NF can work incorrectly due to Freon entering the premises. The reason is microcracks in the tubes due to improper operation or wear.

Cracks often appear if the refrigerator has not been defrosting for a long time, or the user tried to speed up this process independently, knocking out the ice with a solid object.

Malfunction of one of the compressors

In this case, the refrigerator works incorrectly. and the refrigerator continues to function in normal cooling mode. Such a malfunction has to face owners of turquoise models 14 or Atlant.

Sealing rubber band problems

A common failure of the refrigerator is damage to the sealing elastic band, which can be sigred or peel off.

The cause is often a long simple unit. Air enters the chamber, increasing the internal temperature.

Because of this, the compressor of the Beko refrigerator or any other brand increases power, but does not solve the problem, but only wear out faster.

Mechanical and chemical damage

During operation on the housing of household appliances, mechanical damage appears. from cracks to holes in the rear wall.

The reasons for the appearance are from poor.quality manufacturing materials to improper operation or transportation. Due to damage, air enters, reducing the effectiveness of freezing.

Oxidation and rust on the tubes

Over time, pipelines with refrigerant begin to flow due to corrosion of the walls. Freon goes through the formed holes, and the cold does not enter the chamber.

Urgent adoption of measures to eliminate the problem is required, otherwise it will lead to the failure of the compressor.

What to do if the freezer stopped freezing

The list of malfunctions of the freezer is quite large. Having determined for what reason the products are not frozen, and the compressor constantly works without turning off, it is worth moving on to solving problems.

Part of the operation to restore work can be performed independently, another. requires the purchase of expensive details and intervention of specialists.

Frost repair in the refrigerator

Solving problems with the freezer should be given the reasons:

• The neding in capillary systems is eliminated by light tapping through tubes that can move the stuck particles. Drainage pipelines are cleaned with filling with hot water using a rubber pear.
• To restore the operability of the thermostat and thermostat, they can only be replaced. To identify the cause of the problem, after carrying out the corresponding repair, can only be a master.
• Restore the dry.drying of the camera will be only its complete replacement.
• Overheating of the compressor, due to which the cooling mode is violated, you can try to compensate for by pushing the refrigerator from the wall. If this did not help, the detail is changing.
• You can try to deal with mechanical damage yourself. The equipment is defrosted, the damaged place is filled with foam or insulation.
• The malfunctions of the touch sensor, due to which the wrong data is transmitted to the control system, are eliminated by the replacement of the device.
• If the Indesit No Frost model does not freeze, the issue is often solved by the replacement of the heating device.
• Rust from the tubes is eliminated by processing with a special tool or 9%vinegar. Before processing, you should check the action in a small area, only then using on the entire oxidized surface.

Knowing how to solve problems with the refrigerator, which is poorly freezed, you can try to fulfill the relevant recommendations for its repair. Simple problems are often eliminated with your own hands.

However, in the absence of experience or confidence in their abilities for repair, it is worth calling a specialist. After all, the incorrectly performed repairs will not only not return the work capacity, but can make the problem even more serious.

Original technique with a guarantee from the manufacturer

It is best to buy ASKO equipment in a company store. We guarantee the authenticity of all products in the catalog and give out a guarantee from the manufacturer: for all household appliances. 24 months, for professional equipment. 12 months. You can order goods with delivery to any region and get advice on any issue in “Online” or by phone.

ASKO R2282I refrigerator

The freezer works in the refrigerator, but the camera is not

We will analyze what to do if only the freezer works for the refrigerator, and why the upper chamber does not cold, although it is not noticeable between temperatures.

It is worth paying attention to the operation of the engine-compressor: when damage, it works without stopping and overheats a lot. The reason could be simple problems:

• Poorly closed camera door. If the tightness of the sealing rubber or the door sagged, the cold air from the chamber constantly exits outwards.
• Problems with installation. If the room is hot or the equipment is near heating devices, then cooling will occur constantly. Therefore, the refrigerators “Indesit”, “Nord” and other brands will not work, although the freezer works. Move the body from the battery or stove, install the regulator for less.
• Freon leak. As a result of damage to the circuit or due to impaired tightness of the wall, the cooling gas comes out, it becomes not enough for normal cooling. It is necessary to repair and refuel cooling gas.

The situation when the refrigerator began to freeze like a freezer is also not normal. The temperature rises in the department, the products freeze, snow and ice grow on the walls. Why is this happening?

• The door seal does not fulfill its function. there is no tight fit to the body. When warm air enters the chamber, the system compensates for an increase in temperature with constant cooling, so the compressor does not turn off to rest.
• Zasor of the drainage opening. On the walls of hoarfrost, snow, and under the lower boxes. water. During normal operation, the refrigerator turns on the hike: as a result of a drop of moisture, flow down the walls into the drainage hole, and then removed from the system. If the hole was clogged with crumbs, small garbage, then moisture has nowhere to go. It is necessary to clean to resume the work of equipment.
• Temperature control in the department or air sensor is faulty. The main fee does not receive data on the temperature in the camera, so it does not submit a command to turn off the engine.
• The valve does not switch, so the top of the refrigerator may not freeze. In a technique where two cameras are cooled by one engine, a switch (valve) is involved. If he sticks or breaks, then chilled air will enter the freezer, but he will not reach the refrigerator.

The refrigerator does not cool, and the freezer works

Only the freezer works in the refrigerator. How to rectify the situation? There are probably problems with one of the nodes of technology. it is advisable to conduct diagnostics and repair. Consider the main problems:

• The fan motor broke, so the refrigerator camera stopped cooling and freezing. When you do not hear the sounds of working blades, check the fan. If it is frozen, then do the defrosting of the department. After defrosting and re.starting, the fan should earn, and if not, then its motor needs a replacement.
• If the freezer is freezing, but otherwise the two.engine refrigerator is warm, the point is in the compressor. Since the lower camera works, its motor is working. it means that the breakdown happened to another engine. Need repair or replacement.
• The refrigerator compartment is poorly freezing and cooling? Probably a drainage system or a capillary tube closed. The reason may be in the leak of the refrigerant. you need a complete diagnosis of the system and eliminate the problem.
• Modern refrigeration systems are equipped with many sensors who send information to the module. The cause of the breakdown may be a malfunction of one of the sensors. For example, if the Samsung refrigerator does not freeze, you need to check and replace the sensor.

We figured out why one of the cameras does not cool. Now you can correctly determine the cause of the problem and try to eliminate it or contact the service center.

The main camera does not cool, and the freezer works. what to check

When the upper chamber does not cool, you may encounter two problems: damaged products or high wear of the main parts of the refrigerator. Когда что-то одно в системе не работает, на остальные узлы идет повышенная нагрузка. Therefore, if you notice that the camera does not cool, but warm, it is worth taking urgent repair measures.

To exclude a breakdown, first check the following points:

• How tightly the door closes. Most likely, the camera is not closed enough. Change the location of the products on the shelves, arrange containers and pots, and the temperature will soon be included in normal mode. If you notice the ice or a snowy “fur coat” on the wall, carry out complete thawing. after turning on, the work of the equipment should normalize.
• Fan work. Often in two.compressor models of the fan blades can freeze, which blocks its rotation. As a result, the camera works, but does not cool, because the cold is not pumped out. To detect a fan breakdown, listen to the operation of the technique. usually the coolery work of the cooler is heard. If the fan is silent or on the contrary, it creaks strongly due to the fact that the blades are beating on the ice, it is worth thinking about defrosting for 10 hours.

Important! Defrost the equipment for at least 10 hours. less time will not be enough to complete ice thawing, and the problem will not be solved.

If, after checking the door and the fan, it turned out that everything was in order, or defrosting did not help, then the qualified help of the master is required. Disconnect the refrigerator from the network and contact the service or try to independently find out the cause of the breakdown.

Why the camera does not work in the refrigerator

If the factors listed above are excluded, the reason for the lack of cold in the main compartment lies in the breakdown. If you have a refrigerator of the brand “Samsung”, “Indesit”, “Stinol”, “Shivaki” or any other, a table with possible breakdowns will come to your aid.

Such symptoms also indicate a refrigerant leak, only in the area of ​​the steel circuit of the freezer compartment (in models with the lower arrangement of the freezer).

Blocks of the drainage system provoke flowing excess water to the front of the freezer compartment. In this area, a steel circuit passes behind the plastic panel, which prevents the appearance of condensate on the sealant. Plastic in view of its porous structure passes the water inward, which is why the steel part rusts, cracks appear on it, and the freon disappears.

Not every malfunction has “symptoms” by which it can be detected. The failure of the camera can also provoke such malfunctions:

• Damage to the launch relay. It is commonly caused by the natural wear of the part or the voltage jump on the network. The details of the part are required.
• Clogging of the capillary system or blockage of the filter-dryer. In the system, oil circulates, sometimes it causes a blockage of a capillary tube, which interferes with normal circulation of freon. If the master confirms the problem, oil and freon are changing.
• Failure of the air thermal sensor of the refrigerator or evaporator sensor (for electronic models). In this case, the control board does not receive the temperature signals in the chamber, therefore the compressor does not start, the temperature grows. We need to replace the failed node.
• Temperature breakdown (for mechanical models). The situation is similar-the compressor does not start due to incorrect temperature indications. Replacing the part will solve the problem.

If you were not able to independently identify the breakdown and find out why the refrigerator does not cool, entrust this task to a good specialist so that your refrigerator has worked for many more years.