Home Refrigerators Stinol refrigerator does not start the engine
Refrigerators

Stinol refrigerator does not start the engine

The freezer does not work and the refrigerator works Stinol

You were going to have a bite and found that inside the refrigerator, the chamber is abnormally warm, and in the freezer it is excessively cold? Or the compressor continuously works, although yesterday it periodically fell silent, making the stipulated stops? It is not pleasant to learn about the breakdown of such an expensive device, is it not true?

But perhaps the problem will not be as global as it seemed at first glance and everything will be able to fix it with his own? We will help you find out why the refrigerator does not work, and the freezer works and tell you how to eliminate the detected malfunction.

The article contains the most common reasons for this kind of breakdowns and discusses the ways to correct them. Visual photographs and video recommendations from experts are selected that will help to find a malfunction in various models of refrigerators.

Device and principle of operation of the refrigerator

The compressor is overtaken by its pressure freon (cooling agent) into the condenser node. There the gaseous refrigerant condenses into the liquid fraction. This process is accompanied by heat release, which is discharged through the rear panel of the refrigerator.

Liquefied freon is supplied to the system of thin tubes, after which it again takes a gaseous state, and when it is in the evaporative block, it boils. Evaporator and generates cold. Freon completes its circulation, returning to the compressor.

The cold that has arisen primarily enters the freezer, and from it is already supplied to the refrigerator. forcibly or naturally.

This gives the freezer the ability to maintain cold temperature even when the aggregate elements are damaged.

In two.compressor refrigerators, one compressor serves the freezer, and the second. refrigerator. This is convenient in that, if desired, you can turn off some of the cameras and use only one

As soon as the lack of cold in the cooling compartment is noticed with a proper freezer chamber, you need to try to analyze the situation yourself.

User actions in case of suspicion of a malfunction of the unit should be as follows:

  • to establish by observation which cold does not get into the cameras;
  • Clarify whether there are any heat sources near the refrigerator, for example, heating batteries, heaters, kitchen slabs, etc. D.;
  • Determine whether the rubber door sealing gasket is valid, whether there are objects (pieces of food, crumbs, etc. P.), preventing the tight closure of the door.

It will also be useful to inspect the rear surface of the refrigerator for the presence of mechanical damage, and all nodes and systems for rye, oxidation.

How to check the launcher and the refrigerator thermaller for working capacity is an algorithm for checking in different models

Any modern electromechanical equipment is equipped with special devices that regulate its operation and protect from overload. In the refrigerators of any manufacturers, such a device is a start.up relay. An important role in the refrigerator installations plays the thermallane. Its malfunction can lead to an incorrect cooling mode and the loss of equipment performance.

Launch relay connection diagram

This device is necessary to start a single.phase asynchronous compressor electric motor. The engine stator includes two windings. starting and working. The first serves only to create a starting moment and start the compressor. The second winding is needed to maintain the rotor in working condition by continuous supply of alternating current to it.

Important! To adjust the process of supply and disable the power to the starting, working winding of the electric motor, as well as for the function of protection against overloads, a start.up relay is provided.

The mechanism of induction circuit

Relay connection diagram is not complicated. The input of the device is supplied conditionally “zero” and “phase”, and at the output of the “phase” is divided into two lines. The first fishing line for the trimmer is connected to the working winding of the electric motor, and the second is suitable for the launch winding through the launch contact.

In the relay of old and modern refrigerators, the current is supplied to the working winding through the spring with high resistance, and then through the connection with the bimetallic jumper. With a strong increase in the current in the circuit (jamming of the engine, the closure between the turns and other. breakage) The spring is heated, in contact with the jumper, which, under the influence of temperature, changes its shape, thereby blurring contact and turning off the compressor.

In this scheme, a coil (K1) is used to start the electric motor, which is sequentially connected to a circuit with a working winding. The voltage supply with a motionless engine rotor provokes an increase in the current on the coil with the formation of a magnetic field attracting a movable core, closing the start.up contact. After gaining revolutions by the rotor, the current in the circuit decreases, the magnetic field in the solenoid decreases, the start.up contact is opened with strength or compensating spring.

Posistory inclusion mechanism

In modern household refrigerators, a launcher.protective relay is used with a built.in posistor (a resistor that increases resistance with an increase in temperature). Scheme of this device (rice.2) is similar to an induction relay, only instead of a coil to close and open the launch contact, a posistor connected to a starting circuit is used.

When the power supply is supplied to the compressor, the resistor temperature is small and it passes the current to the launch winding. Since the resistor initially has a resistance, it heats up and opens the starting circuit of the starting winding of the engine. The cycle is repeated after the thermallane is triggered and the subsequent re.turning on the refrigerator.

Scheme of thermorelele

The thermostat in the refrigeration unit plays the role of a device that supports the operation in a given temperature mode by periodic turning on and disconnecting the compressor. At the present stage, 2 types of thermallane are used:

This manometric type device. The bellows and its tube (sealed corrugated metal container) are filled with freon or chlormetil in the form of steam. The pressure of the working environment directly proportionally changes when temperature changes. At the end of the tube, the freon is in a liquid state and is pressed to the evaporator.

With an increase in the temperature, the pressure of the bellows on the spring increases, the lever is triggered, the contact closes. With a decrease in temperature, everything occurs the opposite. The contact opening mode depends on the force of the spring, which is regulated by the control handle.

Mechanical thermallack in their work rely on the temperature in the evaporator, and electronic brothers. on the air temperature in the chamber. A positive moment of electronic models is the ability to indicate temperature (that is, a person can visually evaluate the work of the thermostat) and a lower error.

The temperature regulator in this scheme is the LM335 thermal attemptor. The device is a zener diode, sensitive to temperature changes. The climate in the refrigerator chamber is regulated by variable resistance R4. With an increase in air temperature at the output of the TLC271 comparator, a signal appears that opens the KT3102 transistor, which starts the refrigerator. Accordingly, when the temperature decreases, zero appears at the comparator’s output, the compressor turns off.

Checking the refrigerator relay for performance

If the refrigeration unit does not turn on or its inclusion occurs irregularly, then most likely the case is in the starting relay. The reason for its malfunction may be:

  • Oxidation or burning of contacts.
  • Mechanical damage.
  • Overheating of the positive element.
  • Violation of relay mounting, leading to its incorrect location.
  • Figus of a spiral.
  • The core jamming.

No need to rush to buy a new refrigerator relay, it is better to know how to check it, and try to do it.

The solenoid is pulled out in the induction mechanism, the contacts are checked, during oxidation, they are cleaned with sandpaper. The core can be broken, then it needs to be replaced. Wipe with alcohol in contact surfaces. Check the integrity of all elements.

It must be remembered that the relay of this type is installed strictly in a certain direction indicated by the arrow. After the above actions, we attach the relay to the compressor and turn on the refrigerator.

If the engine has not earned, then most likely a compressor breakdown.

Checking devices RTP-1 and RTK-X

To check, put the relay in the correct position (arrow up) and call the 1 and3 Contacts with a multimeter.

If the contacts are nicknamed, then the relay is regular. In these models, a visual inspection is desirable, since the closure can occur through the plate of the contact holder.

Checking devices DHR and LS-08B

DHR needs to be put with a bar with the terminals up and checked the integrity between 1 and 3 or 1 and 4 with a multimeter.

Stinol refrigerator malfunctions and their elimination

Stinol brand refrigerators are popular with consumers due to high quality and good price. In addition, the cases of such refrigerators are covered with anti.corrosion solutions. And the manufacturing company itself belonged to the international brand of household appliances Indesit.

Despite the fact that Stinol’s refrigerators are no longer produced, they are still used in everyday life, but the time and long.term use of even such reliable technology leads to breakdowns.

This article will try to answer the question: is it possible to repair the Stinol refrigerator with your own hands?

Features of the refrigerator

The freezer of the STINOL refrigerator is made of polystyrene. The space between the compartments is filled with polyurethane foam for thermal insulation. The capillary pipeline is used as a throttle, which is why the refrigerator is sensitive to changes in humidity and air pollution.

All Stinol refrigerators are divided into evaporative and compressor types. They work as follows: the device uses a substance called a refrigerant for cooling. this is a liquid that evaporates at room temperature.

The process of the refrigerator is as follows: the vapors of the freon (refrigerant) are constantly submitted to the radiator, which is located behind the refrigerator. Then Freon condenses in a radiator, where he gives heat, after which he enters the capillary tube, from where the freon is injected into the evaporator, and then the process is repeated again.

The refrigerator can have one or two compressors, which depends on the model. The compressor is a steel coil, which is recorded by metal plates. The presence of several compressors allow you to separately configure the operation of each refrigerator compartment.

Refrigerators have two types of evaporators:

An important element for the stable operation of the refrigerator is the electric system. It consists of such elements:

  • When voltage is supplied, the current moves from the thermostat to the forced thawing button, then to thermal protection, after to the launch relay and from it enters the motor winding. The current entering it gives voltage higher than necessary, this is because the starting relay works and closes the contacts only with this voltage level.
  • After this, the relay transfers the current to the launch winding, and the engine begins to rotate. The motor works, the refrigerator begins to freeze. When the temperature reaches a given level, the thermostat is turned on. He opens the contacts, stopping the flow of current to the compressor, which is why he stops. The work resumes as soon as the temperature reaches the required level.
  • In case the motor overheats, there is a thermal protection relay. Когда температура становится слишком высокой, специальная деталь на реле − биметаллическая пластинка − выгибается и размыкает контакты, чтобы потом остывший элемент встал обратно и снова замкнул контакты.

Diagnosis of malfunctions

Before proceeding to repair, you need to determine what exactly does not work. To do this, examine the device and its components:

  • For example, a compressor that should not make excessive noise, in addition, the compressor should periodically turn on and turn off.
  • If it is noisy or working continuously, then this is a sign of a breakdown.
  • You should also check the temperature in the refrigerator. There should be no hoarfrost and water inside.
  • It is also necessary to check the metal elements of the refrigerator. Over time, they can be covered with corrosion, which will lead to a refrigerant leak and compressor breakdown.
  • Make sure that everything is in order with power sources, the presence of electricity in the house, the integrity of the power cord, the serviceability of an electric fork.
  • Check the rubber seal on the doors of the refrigerator, and whether they fit tightly.

The most common breakdown of Stinol refrigerators

The causes of breakdowns are usually incorrect installation and use of the refrigerator, mechanical damage, high temperature, voltage changes.

  • Why the refrigerator does not turn on:
  • Constressor winding.
  • The thermostat malfunction.
  • Cable or plug damage.
  • The temperature controller is broken.
  • Seal defect.
  • Filter filter.
  • Compressor malfunction.
  • One of the refrigerator chambers works, and the other is not (freezer or refrigerator compartment), which can happen: this can happen:
  • Refrigerant leak.
  • Depressurization.
  • One of the compressors broke.
  • Damage to the refrigerator, the doors of the refrigerator or the structure itself:
  • Deforming the structure.
  • Gaps between the seal and the surface of the refrigerator.
  • Lighting and light indication in the refrigerator do not work:
  • Alarm failure about opening the refrigerator.
  • Lack of food.
  • Lighting devices themselves broke.
  • Intended hoarfrost or crossed products:
  • Too strong cooling level.
  • Poor fit of the doors.
  • Thermoregulator failed.

Elimination of stinol refrigerators

Before proceeding with independent repair, it is worth making sure that it is in your strength, otherwise it is better to contact the master. If it is still decided to make repairs yourself, and it was decided what has broken, then you can begin.

Compressor and suspension repair

It is better not to touch the compressor itself without the availability of the necessary knowledge and equipment, since during independent repair, dust and moisture from the air come into the compressor, which will eventually have to change it anyway.

But the suspension suspension can be repaired by yourself. Its deformation can lead to improper operation of the compressor. First of all, you need to make sure that the elasticity of the set of installation legs is not less than 8-10 mm. If the dimensions are smaller, then the shock absorbers must be replaced.

Stinol refrigerator motor does not start

Good afternoon, the engine is not launched at the Stinol refrigerator, please tell me the real cost of engine repair?

Hello, compressor replacement is about 4500 thousand

Good afternoon, so the start-up relay can be faulty or thermal regulatory system? We have such a repair from 1000r

Perhaps the problem in the thermostat or compressor relay. If it is not failed by the compressor of the repair all the same, it is not subject to change, it is necessary to change. Compressor replacement cost from 3000r

Change the compressor, see if the contact leaves

Similar questions

The compressor of the refrigerator broke the reason more than a year ago Stinol 103 L refrigerators

Stinol 103 l refrigerator does not work.to. his compressor has broken, tell me for what reasons and how much does it cost to replace with a new?

Hello. Our Stinol 101 refrigerator stopped turning on, for what reasons and the possible repair price?

Good day. Our refrigerator STINOL Two.chamber does not freeze the freezer, I would like to know about the approximate.

  • Dolce gusto coffee machine
  • Service center
  • Safeing cartridges Krasnodar
  • Repair of phones in Rostov on the Don
  • Libra repair
  • DNS Service Center
  • Werk
  • Repair of Volgograd Phones
  • Repair of radio equipment
  • To Ras
  • Repair of televisions Kazan
  • Repair of TVs Yekaterinburg
  • TV repair in Tver
  • Phone repair in Lipetsk
  • Radio repair
  • TV repair in Kaliningrad
  • Service centres
  • Automatic wash Krasnodar
  • TV repair in Orenburg
  • TV repair in Tula

The microwave does not warm what to do the video more than a year ago microwave ovens BBK MO2081S

Generally stopped warming the food of the microwave BBK MO2081S, what to do?

Need a model of the burner of the burner more than a year ago Beko CSE67100 GW electric stoves

The oven does not work at the Beko CSE67100 GW electric stove, what to do?

The error CD Card error burns on the electroophytrium display, which means?

You need an external hardened glass of black more than a year ago built.in ovens Siemens HB634GHS1

You need an external, hardened glass, black for an oven. Help, please find. vitoc007@yandex.ru

Washed the headlights of the headphones with a foamy cleaner and washed off with a wet rag (not for the first time), turned on, everything works, turned off and put it on.

An incomprehensible mistake is highlighted more than a year ago built.in ovens Gorenje BO 658A31 WG

After turning on any programs, after some time, an incomprehensible error is highlighted. PROB and temperature icons and probes. Not.

The microwave oven spent inside the cause more than a year ago DELFA D20MW microwaves

Our microwave oven Delfa D20MW when ruined food, all the time sparkles inside, for what reasons, it can be?

The Viber code does not come to the tablet more than a year ago Amazon Kindle Fire HD 8 tablets.9 4G 64GB

The Viber code does not come to the Amazon Kindle Fire tablet, what to do?

How to install a washing machine Automatic so that the Sharp ES-GFC6122W3-UA washing machines did not jump over a year ago

Good evening, gentlemen. Well, advise, good, how to install a washing machine Automatic Sharpe on a wooden floor so that it is not.

Good afternoon. I want to know what is the reason when the oven reads suddenly squeaks, and U01 appears on the scoreboard, what does this mean.

Why the turquois refrigerator does not start more than a year ago Biryusa refrigerators 18 with

Who has at least once had such a problem, why the turquois refrigerator does not start, then be kind, tell me what this is connected with, in advance.

The washing machine works but the water is cold more than a year ago Washing machines Indesit iwud 4105

Good afternoon. The washing machine works, but the water is cold. Checked Ten, he is a whole that could be the reason?

The screen on the tablet burst on the tablet more than a year ago 3Q Qoo tablets! SURF TU1102T 1GB DDR2 32GB SSD WIMAX

Good afternoon. The screen burst from the blow on my tablet and the sensor does not work, how much will it cost a complete repair?

Our one.compressor refrigerator does not cool, and the freezer works, tell me, please, why is this happening?

Features of the device

The refrigerators of this brand consist of a standard rectangular metal wardrobe with a built.in inner chamber. The freezer is made of durable polystyrene. Between the two blocks is filled with polyurethane foam, which is a powerful thermal insulation material. The capillary pipeline performs the role of a throttle in the diagram. Thanks to this part, the refrigerator becomes sensitive to high humidity and pollution.

Depending on the lineup of the model range, 1-2 compressors are installed in the technique, which have a vertical axis. The part is located in the lower cabinet block. The device is a coil of a steel tube fixed in metal plates.

Ремонт холодильника Stinol 110 на дому

Diagnostics of the refrigerator

To find out the possible reason for the problem, it is necessary to carefully examine the unit for the working condition of the elements:

  • check the main nodes for corrosion of parts, deformation, mechanical damage to the components, violation of protective coatings;
  • explore the device for tightness, strength of attaching parts and automation devices;
  • Check 3 functional parameters of the device: temperature in the freezer and near the rear wall of the cabinet consumed power.

Reasons why the stinol refrigerator does not freeze

In the modern two.compressor unit with the No Frost system, two separate relay controls the temperature inside the chambers and two separate contours are cooling.

If a household refrigerate unit works, but cannot maintain the necessary temperature in the upper chamber, and in the lower products are well cooled, the reason is either in improperly set settings, either in internal breakdown, or in the leak of the grocery compartment.

You can understand for what reason the stinol refrigerator is badly freezed if you perform a number of actions.

Long defrosting and correct inclusion in the work

Before any manipulations with the device, you need to turn it off from the network and remove products and empty containers from it. In order to understand whether to change the refrigerator according to the warranty or it is working, you need to defrost it completely and let it stand for a day without connection and without products. This is done in order to completely remove condensate from the system.

  • The reason that the upper chamber does not freeze in the refrigerator, and the lower one works, can be an accidentally selected fast frost mode or hasty simultaneous laying of a large number of warm products into the compartment.
  • Especially often the problem of poor cooling against the background of the good operation of the freezer is pursued by the newly purchased units.
  • Another reason why the top chamber of the Stinol refrigerator does not freeze is often a fan malfunction: its blades can be covered with ice and jam, which is why the leading electric motor can burn out.

You need to upload the device only after a few cycles of turning on-off the compressor and reach the operating temperature. Products need to be applied in small portions, taking breaks to cool them.

Elimination of warm air leaks into the upper chamber

If the defrosting did not help and the matter does not concern the new device, the reason why STINOL stopped cooling the products well, may be in the leakage of the sealing gum on the door.

The constant ingress of warm air outside does not allow the device to reach the desired mode and turn off the compressor, which provokes the rapid formation of ice (hoarfrost) on the back of the department. If defects are detected in the seal, it is necessary to replace it. You can do this yourself or calling the master at home.

Diagnosis of internal breakdowns of the refrigerator

Understand what the problem is and why the Stinol refrigerator does not hold the temperature poorly, you can look at additional symptoms of the malfunction:

  • The lack of a characteristic sound of his work is indicated about the breakdown of the fan. If, on the contrary, a loud noise is heard, it means that its impeller and working space are covered with ice and defrosting is required.
  • On the breakdown of the motor, which leads the compressor of the upper chamber, indicates the inability to launch the unit for more than a few seconds and the flow of oily liquid from under the case.
  • About the leakage of the refrigerant from the contour of the product section, in addition to the fact that Stinol has stopped freezing, several symptoms are said: bloating on the plastic walls of boxing and their icing (often uneven); spots and streams of rust on the case near the freezer; Long.term continuous operation of the compressor, an almost non.heated condenser wall. Sometimes symptoms are noted at the same time.

One common problem. the upper chamber of the refrigerator does not freeze for an unknown reason. it unites several more internal breakdowns, which only “opening” will help and diagnosis of individual units of the system.

Most often out of order on Stinol refrigerators, as on most others, they come out:

  • Start relay. The reason for its breakdown is wear or short.term voltage jump.
  • Filter-dryer. Oil decomposition products clog the capillary system and interfere with the circulation of the refrigerant.
  • Thermal attemptor or sensor sensor (on modern electronic models). Sensors stop working from a voltage difference or from internal defects.
  • Temperature controller. Relay fails either due to mechanical wear, or after a voltage jump.

It is possible to reliably establish why the STINOL refrigerator has stopped maintaining the desired temperature of the products, although the freezer works, only by opening and diagnosing the device. If the recommendations from the first part of the article have not come up and the upper camera still works badly, it is better to invite a qualified master. He will find out why this is happening.

Stinol refrigerator does not work, reasons

What to do if the refrigerator “Stinol” does not work? It is worth trying to determine the breakdown. Perhaps you can eliminate the problem yourself, and our article will help in this.

STINOL refrigeration equipment is known for high quality. The metal case of equipment is always covered with corrosion solutions, special painting technology provides prolonged operation without scratches and defects. But even high.quality technique can break.

The refrigerator does not turn off and constantly works

This is the most common cause of non.betting in the refrigerators “STINOL“. If your technique with one compressor does not turn off, pay attention to the signs of a breakdown. You may notice that the freezer department is normally freezing, and the upper refrigerator does not work.

The cause of the breakdown can be in the leakage of the gas-freon. This is a refrigerant that is responsible for cooling air in the departments. The leak may be in the steel circuit. To eliminate the malfunction, it is necessary to detect damage, eliminate them and refuel the system with freon.

  • The door of the refrigerator. How tightly it is closed? The cause of loose fit could be the loops that sagged due to the large load of the door. After pulling the loops, the door will be normal to close.It is worth checking the rubber seal. over time the rubber wear out and is polluted. You can replace the seal with your own hands.
  • Set temperature in the chamber. If electronic control, temperature adjustment is automatically performed, and if mechanical, then manually. Check, perhaps the “Super.Summarrons” mode is installed on the thermostat.
  • Ventilation quality. With poor ventilation or installation near the heating radiators, the refrigerator overheates. Trying to compensate for the temperature increase, the motor works without stopping.

If after the check everything turned out to be in order, the case is in the breakdown. What happened:

  • The termistor and thermoregulator broke. In this case, the control module does not receive temperature data in the chamber, so the compressor does not turn off. A faulty sensor needs to be replaced.
  • Clogging of the capillary tube. Due to depressurization, a blood clot formed in the tube, which does not allow the refrigerator to circulate normally. It is advisable to call a specialist who will find the location and eliminate the problem.
  • Fault of the motor-compressor. During prolonged operation, the motor parts wear out, as a result, the compressor lacks power to pump pressure into the tube, so the set temperature is not achieved. The motor needs to be replaced.

Do not wait for a complete breakdown of the motor. Call a specialist for repair, because during constant work on the compressor there is a double load.

For what reasons, the two.chamber refrigerator “Stinol” does not work

It happens that a two.chamber refrigerator does not freeze, and the light in the department is on fire. The cause may be a freon output again. You can understand this by ice on the evaporator or in the leakage area. The check is also carried out:

  • In modern models, installation is checked. If the case leaned forward, the door could open, so warm air enters the chamber. The refrigerator “understands” that it makes no sense to start the motor.The case should be slightly rejected back. To do this, twist the front legs of the refrigerator.
  • When heat and light does not burn in the cells, electrical parts are inspected: wiring, fork, network cord, outlet. Maybe something was overstated or damaged. Then you need to replace the spoiled element.

To make it easier for you to deal with a breakdown, we advise you to pay attention to the signs of a malfunction:

  • You noticed that the light in the cell is on, but the compressor does not start? Perhaps the clicks of the relay are heard, which is trying to start the engine. So the motor burned. The burnt part is not subject to repair, a new element is installed.
  • Refrigeration equipment (I) with electromechanical control does not work, but the light bulb is glowing. The temperature controller is faulty. He does not send the control board data, so the module does not include cooling.
  • If the light burns in HO with electronic control, but the compressor is “silent”, the termistor is checked. He measures the temperature in the chamber.
  • The bulb in the chamber does not glow, the technique does not turn on. There were problems with a start-up relay that launches the motor-compressor. The relay is replaced by a new part.
  • If the refrigerator does not at all give “signs of life”, while the wiring is working. the problem is in the control module, it cannot control the nodes and details in the technique. Therefore, diagnosis, flashing or replacement of the module is carried out.

No cold in the freezer

Most of the modern STINOL refrigerators are produced with two engines. Each of them is responsible for the work of the upper and lower chamber. If the freezer compartment independently defrosts and does not cool anymore, there may be two reasons:

  • Damage to one of the compressors. Check this is easy: touch both compressors. If they are hot, then the case is in the interitoral circuit. Perhaps the problem with the windings happened as a result of a short circuit. The windings are nicknamed the multimeter, repair is carried out.
  • Когда один компрессор нагревается, а другой нет, проблема в автоматике или системе охлаждения «No Frost». The reason can be in the evaporator, relay, thermal attemptor. Diagnosis will help to determine the exact cause.

To cope with a breakdown, watch the video:

To avoid troubles with the refrigerator, as well as to extend its service life will help compliance with the operating rules:

  • Correct placement. It is unacceptable to install equipment near hot batteries, furnaces, close to the walls and furniture.
  • Timely defrosting. In this case, mechanical removal of pieces of ice in the chamber is not allowed.
  • Correct. Overload of the shelves of HO and its doors leads to the rapid wear of details.
  • The temperature of the products. Only cooled dishes can be placed in the refrigerator.
  • Temperature control on the regulator. Do not install the thermostat in the department for the full power for a long time.

If you find a malfunction, do not delay the repair, call a specialist. Now you know what to pay attention to so that the technique has been working uninterruptedly for many years.

STINOL Problems. Support forum. Popular breakdowns and malfunctions

Hello. In the refrigerator Stinol RFC NF 340A, the compressor of the freezer has stopped turning off. Twice caused different.

The refrigerator Stinol 242 Q 002 stopped freezing the refrigerator more than 6 months ago

Good morning. Stinol 242 Q 002 stopped freezing the refrigerator, and the compressor will work for less than a minute and turns off, and repeats it again. AT.

The problem with the compressor in the refrigerator more than 6 months ago Stinol RFC NF 340A refrigerators

Good afternoon. One of the compressors of the refrigerator Stinol RFC NF 340A constantly turns on and turns off immediately after starting, what is the reason?

Samsung refrigerator does not turn on more than a year ago Stinol Stn 167 refrigerators

Good evening. The refrigerator STINOL STN 167 does not turn on when you include in the outlet, it will have a little and shut up a little. What is the problem?

Good afternoon. The refrigerator Stinol Std 125 on the scoreboard error-al. The temperature adjustment mode works only in the freezer.

Oblique doors more than a year ago Stinol Stn 167 refrigerators

Hello. We bought a new Stinol refrigerator with oblique doors, and they said, they say not a warranty case and do it yourself as.

The sound of overflowing water in the refrigerator more than a year ago Stinol STS 150 refrigerators

Good evening. STINOL STS 150 refrigerator suddenly began to make the sounds of overflowing water. Why is this happening and what to do?

The refrigerator beats current more than a year ago Stinol 107 ER refrigerators

Before everything was fine, but now the Stinol 107 ER refrigerator is very painful, please tell me how to eliminate the problem.

In the refrigerator, the condensate is poorly flowing down more than a year ago Stinol 101 refrigerators

Hi all. Stinol refrigerator 10. On the back wall, condensate flows into a hollow, but uneven. But on the right is good, but on the left is not.

The refrigerator compressor is not launched more than a year ago Stinol 110 EL refrigerators

Hello. In the freezer of the Stinol 110 refrigerator, the fan constantly works and is periodically audible that he is trying.

The new refrigerator is rarely turned off more than a year ago Stinol Stn 167 refrigerators

Dear masters, please help with advice. Bought the refrigerator Stinol STS 167. It works a week. He has a problem: rarely disconnects.

Stinol refrigerator does not turn on more than a year ago Stinol 101 refrigerators

Good afternoon. When defrosting, accidentally broke the tube in the upper chamber of the Stinol 101 refrigerator and after that it stopped turning on.

Hello. The light burns inside, and the refrigerator does not start, please advise what to do?

Hello. Our refrigerator STINOL STD 125 rolls on the floor when opening doors. Please tell me what needs to be done?

Good afternoon! The Stinol refrigerator began to freeze in both chambers and at the bottom and below, tell me, please what is the reason?

Good afternoon! Question about the refrigerator Stinol. The freezer is covered with ice, and in the refrigerator, the temperature is almost.

In the refrigeration chamber (Stinol, the No Frost system) appeared rusty sinks, the photo is clearly visible. The refrigerator at the same time, it works properly. What.

Only a refrigerator does not work in the STINOL refrigerator, and the freezer works, whether you have to do repairs dear? Thanks.

Noofrost does not work on the Stinol refrigerator more than a year ago Stinol RFC NF 340A refrigerators

Good afternoon, the know-frast system does not work in the Stinol refrigerator, and the water flows to the floor, what to do?

How freezes freezer

The evaporator coil is installed in the freezer in the form of shelves. A boiling liquid freon moves inside the tubes. Boiling is maintained due to heat, which the refrigerant takes from the air.

Having passed the evaporator, the liquid becomes a steam that sucks the compressor. Through it, Freon pairs are pumped into the capacitor to become liquid again and go through the capillary pipeline to the evaporator for a new cooling cycle.

The capillary is needed to create a pressure difference, thanks to which a liquid freon boils. The complementar stands on a suction tube between the evaporator and the capacitor. It is needed for the balance of the system if the freon is more seasoned than required. The draining filter takes excess water from the refrigerant when leaving the capacitor to the capillary.

As the refrigerator cools

Freon in the “crying” evaporator gets through the condenser, drainage and capillary. Cooling turns on and is turned off at a thermostat signal. During the downtime of the compressor, the evaporator thaws, heated to the plus temperature. Snow frost on the back wall of the camera melts, water flows through the pipe of the drain into the container on the compressor. When the motor is turned on, which is warming up to 90 degrees, the water evaporates.

STINOL is both a brand and model 103, can be attributed to the veterans of the refrigeration market. Therefore, our masters know all the features of the repair and the main breakdown. These are the nodes, most often, refuses Stinol 103.

The thermostat of the refrigeration chamber. from 1500

The thermostat is responsible for the temperature in the compartment and controls the compressor. Cooling is not regulated directly, but through a “crying” evaporator: it contains the end of the thermoregulator tube, which reacts to a change in temperature. When the sensor fixes the set lower temperature value in the evaporator, the contacts open, and the compressor stops. In rest mode, the evaporator of the refrigerator heats up and thaws. Когда температура в испарителе добирается до верхнего значения, заданного термодатчику, контакты замыкаются и включают компрессор.

A faulty thermostat cannot correctly determine the temperature of the evaporator of the refrigerator, so it does not turn on the compressor or, conversely, does not turn off. In the first case, the compartment remains without cooling, and the products spoil. In the second, the refrigeration chamber motor does not turn off, and the compartment itself is rewinds.

To eliminate the malfunction, you need to replace the refrigerated unit thermostat.

The motor-compressor of the freezer-from 1700

The compressor is responsible for the movement of the freon in the cooling system of the freezer. Under pressure, the refrigerant is pumped into the door heating circuit, then gets into the capacitor, from it through the capillary into the evaporator, then pumps back to the motor-compressor.

A faulty engine does not start the compressor or turns off immediately after starting. The freezer compartment is not cooled and the temperature in the compartment is gradually growing. Ice and snow begin to melt, a puddle of water appears under the refrigerator.

It is required to replace the motor-compressor to eliminate the breakdown.

Drenches in the heating circuit of the door. from 1800

The perimeter of the door of the freezer is heated by a steel tube with freon, laid inside. Heating is needed to dry the condensate around the perimeter of the freezer. Over time, the steel tube rusts, the holes are formed in it through which the refrigerant leaves. The leak affects the cooling of the freezer. The camera is at first weaker freezing, and then stops cooling completely.

To eliminate the malfunction, the heating circuit is cut, and the evaporator is connected to the compressor directly. After refueling by freon, the refrigerator will work fine, it will just have to defrost the freezer a little more often so that the door does not overgrow with ice.

Leak in the “crying” evaporator of the refrigerator of Stinol 103. from 2000

The evaporator of the refrigerator compartment is hidden inside the back wall of the chamber and covered with a plastic case. Usually it works without problems, but sometimes, due to the defect of the evaporator pipeline or in places of joints with a capacitor, micro-focus appear through which Freon goes away. Typical signs of leakage are the same:

  • The compressor of the refrigeration compartment. works almost without stopping;
  • The refrigerator compartment is heat, even when the maximum cooling is set;
  • cold capacitor of the refrigerator;
  • Dry back wall of the refrigerator or ice on the back wall at the freon leak.

To eliminate the breakdown, the faulty evaporator is cut and the external inside the camera is hung. Such a replacement is more reliable than the repair inside the case due to the complexity with the restoration of thermal insulation.

Не включается трёхкамерный холодильник STINOL

The compressor of the refrigeration compartment. from 1700

The motor-compressor pumps a steam-shaped freon from a “crying” evaporator to the capacitor, where the refrigerant turns into a liquid. The tube system in the refrigerator is shorter, and the compressor works less, since the temperature in the department is not a minus, but 2. 4 degrees Celsius. Therefore, the load on the motor is less, and breakdowns occur less often.

But there are still refusals. The faulty compressor starts for a few seconds and immediately stops. Sometimes the motor does not turn on at all. Because of this, the temperature is rapidly growing in the refrigerator compartment.

It is required to replace the compressor to eliminate the refrigerator breakdown.

Drilling relay of the freezer engine. from 1500

The relay is responsible for starting the engine and its protection against overheating. When the contact of the relay is closed, the current is supplied to the starting engine winding. If the contact is defective or there is a break, the engine cannot start, and the compressor does not turn on.

stinol, refrigerator, does, start, engine

With a faulty protection mechanism, the engine starts normally, but quickly turns off. Relay mistakenly believes that there is overheating and opens the contact.

Freezer thermostat. from 1500

Thermallera is responsible for turning on or disconnecting the freezer compressor. Data on the thermostat comes from the temperature sensor inside the chamber. The working relay closes the contact contact contact when the temperature rose above the set. And opens, turning off the compressor when the camera has cooled to normal.

About checking the thermostat

The temperature controller often fails, as could be understood from previous stories.

This is due to the working resource of technology, which is enough for a maximum of 5-6 years. The compressor does not start in the refrigerator when this part is broken. It is different when the upper chamber does not freeze in STINOL models.

There are two ways to determine the working condition.

Only in this case is the divisibility of the electrocope support. If necessary, check if the power supply is going on. If something is absent, then the whole system is watched on the subject of integrity and the presence of any removal. If some parts have broken off, they replace.Refrigerator repair helps to cope with difficulties.

If after this the installation does not turn on, then the problem arose somewhere else. By ear, the problem can also be determined depending on where and how additional sounds appear.

If the unit is already more than 10-15 years old, then any malfunctions require a specialist call. Otherwise, the repair of the refrigerator will be dangerous.

about diagnosis and existing problems

Water often appears and accumulates inside the units with a drip system inside the refrigerator compartment. Zoror drainage system is the main reason for the appearance of malfunctions. The purpose of the design is to drain water from the chamber. It passes inside the stinol 101 refrigerator.

If a snow fur coat appears in the freezer, this is also one of the signs of a malfunction. Drainage begins in the compartment where products are stored. Therefore, the presence of a hydraulic plant in this part is mandatory to avoid problems in the future.

note. In practice, this detail looks like a bend of small dimensions. Inside such a part, pollution and other similar components are delayed. The manufacturer often implements additional tools with which cleaning is carried out.

After such actions, the outflow of water should improve. With strong clogging, such actions do not help, there is a need to break through the structure.

The main thing is to adhere to a neat approach. The tubes are made of thin.leaved plastic, which is too easy to damage. It is recommended to use fishing fishing lines, which have a slightly melted end. Get an impromptu cable, which, after immersion inside and clean the system. Then everything is filled with a washing solution, the insides of the STINOL 101 technique are washed with water.

Compared to “crying” systems, constructively options “without hoar” are considered more complex. They differ from existing analogues in that they contain a blowing system to remove excessive moisture. Fan, fuser and timer. the weakest places in systems.

The fan comes from the freezer. The detail is closed or open depending on the model.

Open devices with electronic controls are practically not subject to independent repair, you only need to call the master. Another thing is when the device is simpler, with electromechanical elements. Enough access to the inside. When they get to the fan, carefully study the structure and check the impeller. The knot accurately requires analysis if everything goes tight and does not lend itself to movement. STINOL 110 is repaired almost the same.

Stinol refrigerators. Popular breakdowns and malfunctions

Hello. In the refrigerator Stinol RFC NF 340A, the compressor of the freezer has stopped turning off. Twice caused different.

The refrigerator Stinol 242 Q 002 stopped freezing the refrigerator more than 6 months ago

Good morning. Stinol 242 Q 002 stopped freezing the refrigerator, and the compressor will work for less than a minute and turns off, and repeats it again. AT.

The problem with the compressor in the refrigerator more than 6 months ago Stinol RFC NF 340A refrigerators

Good afternoon. One of the compressors of the refrigerator Stinol RFC NF 340A constantly turns on and turns off immediately after starting, what is the reason?

Samsung refrigerator does not turn on more than a year ago Stinol Stn 167 refrigerators

Good evening. The refrigerator STINOL STN 167 does not turn on when you include in the outlet, it will have a little and shut up a little. What is the problem?

Good afternoon. The refrigerator Stinol Std 125 on the scoreboard error-al. The temperature adjustment mode works only in the freezer.

Oblique doors more than a year ago Stinol Stn 167 refrigerators

Hello. We bought a new Stinol refrigerator with oblique doors, and they said, they say not a warranty case and do it yourself as.

The sound of overflowing water in the refrigerator more than a year ago Stinol STS 150 refrigerators

Good evening. STINOL STS 150 refrigerator suddenly began to make the sounds of overflowing water. Why is this happening and what to do?

The refrigerator beats current more than a year ago Stinol 107 ER refrigerators

Before everything was fine, but now the Stinol 107 ER refrigerator is very painful, please tell me how to eliminate the problem.

In the refrigerator, the condensate is poorly flowing down more than a year ago Stinol 101 refrigerators

Hi all. Stinol refrigerator 10. On the back wall, condensate flows into a hollow, but uneven. But on the right is good, but on the left is not.

The refrigerator compressor is not launched more than a year ago Stinol 110 EL refrigerators

Hello. In the freezer of the Stinol 110 refrigerator, the fan constantly works and is periodically audible that he is trying.

The new refrigerator is rarely turned off more than a year ago Stinol Stn 167 refrigerators

Dear masters, please help with advice. Bought the refrigerator Stinol STS 167. It works a week. He has a problem: rarely disconnects.

Stinol refrigerator does not turn on more than a year ago Stinol 101 refrigerators

Good afternoon. When defrosting, accidentally broke the tube in the upper chamber of the Stinol 101 refrigerator and after that it stopped turning on.

Hello. The light burns inside, and the refrigerator does not start, please advise what to do?

Hello. Our refrigerator STINOL STD 125 rolls on the floor when opening doors. Please tell me what needs to be done?

Good afternoon! The Stinol refrigerator began to freeze in both chambers and at the bottom and below, tell me, please what is the reason?

In the refrigeration chamber (Stinol, the No Frost system) appeared rusty sinks, the photo is clearly visible. The refrigerator at the same time, it works properly. What.

Only a refrigerator does not work in the STINOL refrigerator, and the freezer works, whether you have to do repairs dear? Thanks.

Noofrost does not work on the Stinol refrigerator more than a year ago Stinol RFC NF 340A refrigerators

Good afternoon, the know-frast system does not work in the Stinol refrigerator, and the water flows to the floor, what to do?

Stinol refrigerator motor is not launched more than a year ago Stinol 101 refrigerators

Good afternoon, the engine is not launched at the Stinol refrigerator, please tell me the real cost of engine repair?

Author

Kerariel

| Denial of responsibility | Contacts |RSS