Samsung No Frost refrigerator flashes temperature indicator

Samsung refrigerator flashes the upper chamber temperature indicator

In the No Frost system with dry freezing, a fan is used inside the refrigerator. Its use leads to the fact that the flows of cold air inside are constantly mixed by more uniform cooling of products. After warming up, the air takes the resulting condensate, bringing it out.

This method of work is possible due to the fact that the Samsung refrigerator is a two.chamber No Frost has high reliability. However, over time, the technique wears out and the likelihood of malfunctions increases. In such a situation, it is important to correctly determine the cause of the problem. Of course, having called a specialist, it is easy to do this.

Important! Samsung has created a built.in electronic diagnostic system in its refrigerators, which allows even an inexperienced user to determine what happened to the technique.

However, in order to do this, you need to know how to use such a diagnosis. Based on the data obtained from the sensors, it draws conclusions about the nature of the malfunction. After performing the analysis of the information received by her, she determines the type of malfunction and issues on the display located on the panel, the error code.

Knowing how to read it correctly, the user can easily find out the type of Samsung No Frost that has arisen in the refrigerator. There are instructions that describe in detail what needs to be done in each situation, depending on the code issued by the system. At the same time, it is immediately clear when it is possible to take independent actions, and in what cases you need to call the master. With the list of faults of the two.chamber refrigerator Samsung No Frost, you can find in the corresponding table.

Ways to eliminate breakdowns in Samsung refrigerators

RSA1SHVB1 two-chamber refrigerator (Side by Side) with electronic control and No Frost in both chambers (1 motor-compressor). The freezer stopped freezing, on the display the temperature 21, the freezer and the refrigerator 16 and the display blinks. If the freezer does not work, then the reason may be a malfunction of the evaporator tightening system (the tickle sensor or the heater of the evaporator). If both cameras do not work, then the reason may be in the leakage of the freon, a compressor malfunction or control module. Tell me, the refrigerator Samsung RSH5ZLMR1 (two.door) Side Bai Side is squeaking melody as if the door is open. And the temperature itself changes. If you have x-k RSH5ZLMR1 issues sound signals, with a door closed, then this indicates a malfunction and insufficient temperature in the chambers. There may be a malfunction in the control module, a freon leak or in the failure of the temperature sensor. Refrigerator No Frost Samsung RT 25 HAR4DWW. Water often leaks from the grate under the freezer. I received an answer that you need to remove the casing and clean the drainage tube. The casing took off in x.to. And in the freezer, I did not find a phone, although I was looking with a flashlight. There is a flimsy pallet, it did not dare to remove it. There is no ice on the evaporator or under it. Indicate where this tube is? Or can pour hot water on a tray? And yet, if the temperature controller is rotated to the right, then we lower the temperature? After disassembling the minus temperature at the minimum of the regulator. The drainage tube is under the evaporator below. The pallet that you were afraid to remove is served in order to condensate the text in the drainage. Two.chamber refrigerator Samsung RSA1StWP1 Side by Side with electronic control and inverter compressor. Tell me what the buttons block are called correctly, which are pressed when closing the door so that the light does not burn? The sensor that is responsible for turning off the light and indication with a long-open door of the x-ka RSA1STWP1 is called the Herkonian door sensor. Two.chamber refrigerator Samsung RT 25 No Frost. When included in the network, only the light bulb is included in x.to., nothing else. The noise of the compressor is not heard. I wanted to pull out a launcher, but it did not work. How to remove it? Tell me, please, where can be the cause of the breakdown? The launch vehicle of the relay is extremely rarely out of order. It is removed simply: unscrew the screw on the lid, and the lid will be removed. If both cameras do not work, then there may be the following breakdowns: the failure of the motor-compressor; Freon leak in the system; A breakdown of the tie timer (the unit got into a touch and does not work); The failure of the thermostat; Failure of the heater of the evaporator. RSH5ZLMR Side by Side two-chamber refrigerator with Full No Frost, electronic control and one compressor engine. There were interruptions in electricity for several days, after that mor. The camera began to freeze the meat poorly, and setting the temperature on the scoreboard.17 degrees, could not be rearranged on these numbers, and it comes out.25 and could not fix it. Hol. The camera works as usual. What to do in this case? The reasons that the freezer is rewriting, there may be a lot. To begin with, we recommend defrosting x-k RSH5ZLMR and, if the freezer continues to grounder, then the case can be in the control module and in the temperature sensor of the freezer and pr. Samsung RSA1SHVB1 two.door, Side by Side, inverter compressor. The freezer, instead of the minus, works in a plus, heats up to 30 degrees, which could be? You have x-k RSA1SHVB1 with No Frost, then the case may be in the leak of Freon from the system. If the unit is two.compressed, then the thermostat mor can be faulty. cameras (temperature sensor) or freezer engineer. Samsung RSH5ZLMR Side by Side (two.door). In the refrigerator compartment, the air stopped circulating, and ice was formed in the area of ​​the ventilation hole. A few days later, in the freezer, which previously worked, the temperature rose stably to plus 3 degrees. Yesterday I took off the grate from below on the rear panel of x-ka, washed it along with the sponge mounted on it, and sprinkled carefully. From x-ka previously extracted all the contents. After turning on the empty unit, the temperature in the freezer compartment gradually decreased to 14 degrees, and in the refrigerator compartment remained room temperature. Further temperature decrease does not occur. Initially, apparently, you had a malfunction in the system of hidden the evaporator No Frost (the sensor of the hits, a fuse or a heating heater). Now, most likely, Freon’s leak. Diagnosis of the master is needed. I have a two.chamber refrigerator Samsung RT 25 HAR4DWW. I wanted to ask how to install a dispenser. When the refrigerator itself was installed, they asked about the installation of the dispenser. Refused, now I think how to connect? How to install a dispenser you will find in the operating instructions. Two.door refrigerator Samsung RSA1STWP1. The fan does not work. precisely, the power of 220 volts does not come, but only 60. Most likely, problems with the electronic module or the fan itself. The two.door double.chamber refrigerator Samsung RSH5ZLMR1 Side by Side with the No Frost system in both chambers and one compressor. It works, then the temperature display does not work. Can show one temperature, in fact in the upper and in the. the camera is the process of defrosting. Sometimes squeaks. What to do? It is necessary to check the controls of the control module and the temperature sensor of the refrigerator and freezer chambers. Please tell me what is the inner diameter of the capillary tube in Samsung refrigerators? The fact is that the diameter of the tube does not depend on the brand, but depends only on the power of the refrigerated production and the brand of Freon. The refrigerator Samsung No Frost is constantly squealing, while the Vacation and Super Freeze buttons are burning, please tell me, please? Vacation means the on vacation mode. To turn it off, you can hold the Vacation button for 10-15 seconds, or with the help of increasing and reducing temperature, raise by 1 degree or lower the temperature in one of the chambers. Super freeze means super.commercial. Samsung, the S28BKCSWN/BUS model with a GQR70AG compressor, works without problems, but turns off with a roar, as if something jammed inside the compressor. Please tell me what to do or call the master? It is necessary to put forward the unit and see if the compressor hurts for one of the tubes behind him. Also, pay attention to the rubber shock absorbers (gaskets) of the compressor installation platform, maybe they are dry. Samsung RF62UBR S SIDE by Side. After turning off the electricity, the Hill stopped working. The camera appeared water. Freezer freezes well, incomprehensible symbols on the display. If x does not work.To., then you need to check the freezer chamber. If there is a lot of snow and ice in the freezer, then the matter is the breakdown of the evaporator’s hidden system (the sensor of the tackle or the heater of the evaporator) and the snow prevents the fan rotation. If there is no snow, but the fan does not rotate, then the matter is either in the fan motor or in the temperature sensor X.To. I have samsung no frost. On the front panel, the temperature indicator x.To. constantly flashes and the temperature inside is very high.18 degrees. The instructions say that when the temperature indicator blinking, you need to call the service center. We live in rural areas. What should we do? If in x.To. too low temperature (-18 degrees), the cause of the malfunction can be in the failure of the temperature sensor. If the high temperature (18), then the case may be in the failure of the system of the hollow of the freezer of the freezer (the latch sensor, the heater of the evaporator). Samsung refrigerator, model S28BKCSWHN/BUS. Holo does not work. camera, and the freezer works. Check the freezer, if there is a lot of ice and snow in it, then it interferes with the rotation of the evaporator fan, which leads to the fact that cold air does not fall into x.To. In this case, it may be in the system of hiding the evaporator. a tiemer of the thaw or heater of the evaporator. If there is no snow and ice, then check if the fan rotates, maybe the fan motor is out of order. There is a two-chamber with the No Frost system, it was bought for a long time, the model is not known at the moment: the freezer is working properly, the lower “cabinet” seems to be unreasonable, according to the sensation, the temperature is high, the products sometimes spoil prematurely (the adjustor handle is maximum). What could be the problem? There are many problems in models with the No Frost system: the heater burned out, the thawing sensor has burned out, the fuse (special) was out of order, and also in some models there may be a freon leak, etc.D. Samsung RL28DBSW, the upper chamber does not cold at all. The problem in the freezer. It is necessary to diagnose the thawing system, grounding air ducts, temperature sensors. For a complete and accurate diagnosis, you need to call the master. The electronics of the RSE8KPAS model is buggy. Detachment description: spontaneously switches from normal mode to Vacation and backward mode. A simple attempt to turn off the power and turn on again did not help. At the entrance to the Vacation mode, the Vacation button itself ceases to obey. When unauthorized to return to the Cool mode, does not want to listen to the Freeze button. What will you advise? Judging by the description, this is a malfunction of the control board, possibly a connecting train of the door console with a control board. It is necessary to call the master. The compressor does not turn off in my refrigerator, which could happen? There may be several reasons. Insufficient amount of refrigerant in the system due to leakage, and this is not gaining the necessary temperature in the refrigerator. The thermostat malfunction (temperature sensor) refrigerator. The door is not closed. The unit needs to be turned off and called the wizards for diagnosis three days ago bought x-k RL46RSBSW. Alarm is the fact that the side walls of the case are heated during the compressor work somewhere up to 40-42 degrees. Please tell me, this is a normal phenomenon or it is necessary to intervent a specialist? This phenomenon for these models is quite normal, condenser blocks are located on the sides of the refrigerator, which heat up during operation. Model RT 44MBPG. It all started like this: it began to drip water in the hill. Department. Stopped automatically launched (turned on forcibly, off./ON. In the outlet). Stopped freezing in the freezer. He stopped cooling at all. The compressor works, the fan is noisy, but there is no sense. Please tell me a possible breakdown. Most likely there was a leak of refrigerant, and therefore it does not cold. A call call is required. When transporting the Samsung RT37MW refrigerator and installations, a puddle of water began to form when it is hot. Tell me how to fix it yourself? In order not to form a puddle of water, you need to tilt x-ka back with two front wheels that are below, or a drain pipe jumped during transportation. We purchased the Samsung refrigerator with the No Frost system less than a month ago. There were no problems for two weeks. But yesterday, as I understand it, the cold in the refrigerator stopped produced. The freezer works without problems. In the store they advised to turn it off for a couple of hours, and then turn it on again. So they did, but today everything seems to be fine again, after thawing, but this situation still bothers me. Really only hot weather (as explained in the store) the reason for such a failure? Climate conditions do not affect the operation of refrigeration equipment. Perhaps there is a factory marriage, in this case, contact the warranty service center. X-K RL28FBSI1/XEK. After the electricity interruption, the compressor stopped turning on automatically, but when the super frost is turned on, the compressor works. In this situation, most likely, the control board or temperature sensor was out of order. A calling the master is required. In the right corner of the Holler. the cells over the vegetable basket intensify the ice. Have to defrost every week. Leakage on the evaporator. To save the unit, you need to change the evaporator. The main malfunctions. as a rule, this technique is equipped with a control system based on an electronic controller, in this regard, the control module malfunctions occur quite often in comparison with the rest of the brands. Any household appliances have its weaknesses. As experience shows, the need for repair in most cases is associated with such malfunctions. The failure of the electronic control unit. Replacement of the temperature sensor (thermoresistors). Problems of the thaw system. Malfunctions in the No Frost system. It is not rare that there are cases when the tube is clogged to drain water from the evaporator of the chamber, as a result of which a puddle of water is formed around the unit.

Temperature control methods

Each refrigerator is equipped with a temperature regime control unit. Thermoregulation on the refrigerator can be carried out by different control methods.

There are only two of them, mechanical and electronic:

• Mechanical regulation. Inside, the adjusting temperature of the handle is provided. Through the mechanical effect of the regimes and switch. Typically, the regulator additionally has an image that helps set the desired mode. However, if it is not or it is not clear to you, then in the instructions for the unit you can find all the necessary information.
• Electronic exhibition. This kind of regulation provides for a scoreboard, visualizing degrees and cooling mode. The desired temperature can be set through buttons or sensory response. It all depends on the brand and model.

Modern models of cooling equipment by mechanical control are almost not equipped. Now most often there is precisely sensory regulation. To figure out how to set up your camera will help a technical passport.

How to set the temperature in a double.chamber Samsung refrigerator

If the Samsung refrigerator is two.chamber, the freezer is adjusted separately, it can have an accelerated frost function. The action of the intensive mode lasts no more than 72 hours, with an automatic transition to a standard level.

A new device after connection, it can work for a day without stopping. You can start setting the temperature after stabilizing the regime. It is important to be guided by the instructions. You can rearrange the temperature using buttons and display, or manual regulator. About how to regulate the regime, the manual developed for each series of Samsung refrigerators informs.

How to properly set the temperature in the refrigerator Samsung No Frost

Unlike drip defrusting systems, the system of dry lining changes the temperature balance in both chambers. The evaporator is put into the back wall, continuous ventilation of cameras is created. Samsung two.chamber refrigerators are also possible to configure the No Frost temperature as with a drip defrust, using electronic regulation or manual control.

On the example of the Samsung refrigerator with the No Frost system, the RL33 EAMS model, we will figure out why the display temperature rides. Flashing is explained by the reasons associated with the wrong temperature regime. Often there are deviations.

• The temperature in the Samsung refrigerator is higher, due to frequent opening of the door in a very warm room. If you do not open the circuit for 2-3 hours, the blinking will stop. Perhaps the temperature in these conditions is unattainable. Then nothing remains, how to rearrange the task on the display towards the increase.
• The mode is not set, indicators, notify the need to set control points for the correct operation of the system.
• One of the temperature sensors is faulty.
• With a loose door closed, the system signals a loud sound signal.

It should be noted that Samsung refrigerators are most reliable, and adapted for work in energy supply conditions.

from Boris Kornilov 138 431

Samsung refrigerators have earned confidence among consumers thanks to reliability, noiselessness and economy. Particular attention is attracted by the temperature indicators of the devices. Manufacturers independently determine what temperature should be in the Samsung refrigerator. This is due to multiple research and testing.

However, each refrigerator and freezer chamber have regulators to regulate the cold within reasonable limits. Next, the instructions how to set the temperature in the refrigerator Samsung two.chamber and No Frost.

Depending on the model and type, the temperature modes of the refrigerator chambers are noticeably vary and decrease from the upper part to the bottom. The main cabinet camera is set by 3. This indicator varies up to 2 degrees.

The average temperature of the freezer is about 18 degrees of frost. Here, adjustment limits are noticeably wider. In addition, many models have freshness zones, where 5-7 degrees are the norm. accurate information about these parameters is given by instructions attached to a particular model.

Interesting: Samsung technology allowed to achieve a result when the temperature in one chamber does not vary by more than 0.3 degrees, regardless of its volume.

Adjustment is made from the control panel that is associated with the sensors located inside the unit.

Setting sensors

To help the user in the Samsung refrigerator, there are sensors responsible for the work of a common refrigerator and freezer chambers, control panels, evaporator.

To set the required temperature in a two.chamber unit with No Frost technology is really by means of a mechanical handle or the following keys:

The control panel accepts information from sensors according to the universal scheme, which is responsible for controllers of 502at.

Samsung refrigerator malfunctions

Samsung No Frost two.chamber refrigerators have a panel that shows all the malfunctions. Thanks to it, you can eliminate all the problems in a matter of minutes.

Do.it.yourself repair is almost always possible, if there is a tester, the ability to solder and the initial skills of an electrician or radio amateur

The main problems that are easy to fix for yourself:

• An increase in temperature by more than three degrees can occur due to frequent opening of the door in hot weather. To solve this problem, you just need to close the door tightly and not open it within 3 hours.
• If the sensor shows that the temperature regime is not set, you just need to eliminate this problem by guided by the instructions.
• If in the ice tray some detail is set incorrectly, then a separate indicator will tell you about this. To bring the device to serviceability, you need to use the instructions again.

Such Samsung refrigerator malfunctions can be eliminated in a matter of minutes. The main thing is to pay attention to the signals of your assistant in time.

Such models also have hidden breakdowns. They are almost invisible, but timely diagnosis will save your technique from breakdown.

One of the frequent hidden malfunctions is a defective relay in evaporators. Possible signs of such a breakdown are a continuously increasing amount of hoarfrost on the evaporator. If it does not get rid of this problem, then in a few days the refrigerator will stop freezing, since the thermoregulator’s function will not be performed. To repair the device itself, you need to turn off the unit, pull out all the products from it and completely defrost.

If this did not help, then the timer broke the refrigerator. To eliminate this defect, you will have to call the master.

serious problems without independent equipment cannot be eliminated. If the malfunctions independently eliminate all the malfunctions, then you need to invite the master to check the serviceability of the device and determine the cause of the breakdown.

Typical malfunctions

In most cases, users of such refrigerators face the following problems:

• The freezer stops working. After a malfunction in it, a low temperature is no longer maintained. Often, at the same time, water that has formed from melted ice begins to flow out of the freezer. The cause of the breakdown can be elementary. For example, this may be the result of icing of the door of the freezer, which violated the tightness of the structure.
• Some errors are not related to breakdowns, but are the result of the fact that the user has established incorrect adjustments. Accurate diagnostics in such situations will restore equipment performance at the same level.
• Sometimes the presence of a factory marriage may lead to problems. In such situations, you can sometimes eliminate the problem yourself, and in other situations you will have to resort to warranty repair.

The device does not turn on

If the refrigerator has stopped freezing, then usually the first sign is the leakage of water, the cause of which is an increase in temperature. If the user did not open the refrigerator for a long time, then for the first time opening a faulty device, he can feel an unpleasant odor from the products that recently began to deteriorate. Before setting the temperature in the Samsung refrigerator, it is necessary to eliminate the problem that has arisen.

One of the possible reasons may be the life of an extraneous object under the back cover. He usually gets stuck there due to the fact that he is holding his ice. In this case, it is enough to use a hairdryer to eliminate the problem. The flow of warm air will melt ice. After that, an extraneous item either falls out by itself, or it can be easily obtained and removed.

If the reason for the termination of work is the compressor, then this can be found by the fact that it clicks, but does not start. The reason may be, for example, a short circuit or wire break. For its accurate diagnosis and search for the cause of the malfunction, a special technique is required. In such a situation, when repairing the Samsung No Frost refrigerator, you will need to contact a specialist.

The termination of the equipment may be associated with violations in the operation of the electronic control of the refrigerator or sensors, on the basis of which it works. If the control module is faulty, then it will be necessary to call the service without fail. In the event of a malfunction of the air sensor or a launched relay, the replacement can be made independently.

Wondered door seal

Its most common mistakes are the following:

• Room in a refrigerator chamber of hot dishes.
• Frequent opening of the refrigerator door or when it is kept in open state for a long time. At the same time, air enters the refrigerator from the room, increasing the temperature. This situation is especially unpleasant at the time when there was an emergency shutdown of electricity. If you do not open a working refrigerator, then according to Samsung No Frost, the operating instructions, it is able to maintain acceptable conditions for products for a day and a half.
• Samsung refrigerator malfunctions can occur if there are heating devices in relative proximity to the device. This can happen, for example, in cases where the refrigerator is placed next to the heating battery.
• If tightness is disturbed due to wear of the door laying.
• In the case when the door interferes to closely close icing. It often occurs due to a violation of tightness, when the refrigerator cannot lower the temperature to the right extent and because of this the compressor’s work occurs constantly.

Sensor sensors

The user can independently adjust the temperature from the control panel. the information is provided for it inside the device sensors. It is they who monitor the territory they allocated in the unit. The sensors have the following parts of the device:

• General refrigerator;
• internal space in the evaporator;
• freezer chamber;
• control panel (for environmental measurement).

Installation of the required temperature regime is carried out using the keoling power or fridge keys (or a mechanical rotating handle). On the control and visible user the panel, data from sensors are received through the control scheme. In most cases, the models from this brand are 502at controllers, which are universal.

The failure of any of the sensors of the device leads to a malfunction of the entire Samsung refrigerator. Such repairs are best entrusted with appropriate specialists.

List of malfunction codes

If a problem occurs on the display, the Samsung refrigerator failure code appears. To understand what exactly happened with the unit, you need to cheat with the operating instructions. If it is lost, the forum participants on the manufacturer’s website or specialists from the service department will be able to provide real assistance. The difficulty is that each model of the Samsung unit has its own characteristics in the list of codes.

For example, the appearance on board 01, 02-03, 07, 08-09 means a failure in the sensor of the ice-generator, refrigerator, the environment and the freezer, respectively. Code 11 indicates damage in the condenser, and 10. about the fan malfunction.

Simple causes of samsung units

The technique has enough advantages over the refrigerators of other brands, but after several years of functioning, breakdowns begin. Electronic control in such units is extremely sensitive to voltage surges, and without appropriate maintenance, the devices begin to wear out the details. The electronic type of control takes all the malfunctions to the display in the form of errors and when one of the indicators or an icon on the screen begins to burn, it is likely that the reason is a simple problem, for example:

• The temperature increased in the compartment after loading food products and the indicator caught fire. most likely that the problem is an overly open sash, so the unit needs a couple of hours to restore normal temperature regime.
• The wrong temperature in the department was set. it is necessary to configure all values ​​according to the operating manual.
• The ice tray sensor indicates that it was incorrectly installed. the location of the tray is changed and everything returns to normal.

Attention! The correct temperature in Samsung refrigeration equipment is extremely important, since the difference between the compartments is required not to exceed 0.3 ̊s, in a different version, the technique will not function normally.

In a two.chamber Samsung, the upper chamber may not work due to a frozen fan or an uncovered sash. The door can fit loosely due to the incorrect location of the products in the compartment, which do not allow the doors to completely close. And in cases where the sash was opened for a long time, and ice and yoke formed on the walls of the camera, you need to allow the unit to be thawed for 10 hours, and then check the condition of the sealing gum and door mounts.

When the fan freezes in the refrigerators with the No Frost system, the circulation of the air masses is disturbed and, as a result, the upper chamber is not cooled. To solve the problem, you must allow the unit to defrost and let it relax for 24 hours.

Features of the work of such technology

The following malfunctions can be distinguished in the temperature mode of the two.chamber refrigerator Samsung “No Frost”:

• the formation of ice crust (incorrectly set temperature), which increases the consumption of electricity;
• A full pallet (due to leakage will quickly deteriorate).

A distinctive feature of Samsung refrigerators is the constant temperature of each of the chambers (the difference will be in the range of 0.3 degrees). Various modes are exhibited in different parts of the device. they are significantly different and decrease from the top to the lower part.

• In the main chamber, the temperature indicator corresponds to three degrees of heat, a change within plus or minus two degrees is allowed.
• Now let’s move on to the freezer. here the temperature is already “reigns” within 18 degrees of frost. To adjust (and adjustment is allowed), you need to study the instructions attached to the model.

How to adjust the temperature refrigerator Samsung RT-34 MBSW

Set the temperature control to the Colder position (colder) if you:

• Want to download a large number of products (in a refrigerator or freezer)
• Want to cook ice (in the freezer)
• Want to freely freeze products (in the freezer)

Set the temperature controller between the Colder positions (colder) and “Cold” (cold) for normal cooling and freezing.

Set the temperature control to the Cold (cold) if you are going to store a small number of products in the refrigerator.

Note: If the air temperature in the room is below 5 ° C, set the temperature switch to the “Cold” position (cold) so that the products do not freeze.

Sensor sensors

The user can independently adjust the temperature from the control panel. the information is provided for it inside the device sensors. It is they who monitor the territory they allocated in the unit. The sensors have the following parts of the device:

• General refrigerator;
• internal space in the evaporator;
• freezer chamber;
• control panel (for environmental measurement).

Installation of the required temperature regime is carried out using the keoling power or fridge keys (or a mechanical rotating handle). On the control and visible user the panel, data from sensors are received through the control scheme. In most cases, the models from this brand are 502at controllers, which are universal.

The failure of any of the sensors of the device leads to a malfunction of the entire Samsung refrigerator. Such repairs are best entrusted with appropriate specialists.

Refrigerator adjustment

The spacer allows you to increase the efficiency of the refrigerator.

• Install the refrigerator so that its front part is slightly higher. this provides optimal door work.
• To adjust the position of the refrigerator, turn the legs clock or counterclockwise.

• Before inserting the power plug into the outlet, make sure the proper condition of the outlet and the density of its contacts.
• Insert the fork into the outlet, open the refrigerator door and make sure that the light has caught fire inside the refrigerator.

In an hour, adjust the desired temperature in the refrigerator.

• Provide enough space for installing the refrigerator.
• Right, left and back: 50 mm
• Top: 100 mm
• Distances can be different, depending on the refrigerator model and the measurement method.

• Models of refrigerators shown in this video may vary depending on the region.
• Carefully read warnings and important safety instructions in the user manual.
• If this is possible and is required by law, before connecting it is necessary to conduct tests for compliance with the requirements of electrical safety.

Compressor breakdown

The heart of the equipment is a compressor that is periodically turned on to ensure good operation. If he begins to turn on too often and work almost in constant mode-there are some problems in his stable work, as the indicator and sound signal immediately report.

Carefully inspect the device: there may be a freon leak, in any case, you should not independently eliminate the malfunction, it is better to entrust this matter to a professional. You can harm your actions so that you will have to change this very important, very expensive part of the refrigerator.

Control Panel

The indicator can blink due to a small malfunction in the panel itself-check what position the temperature indicator has, it depends on the setting of the entire mode. Very often, fat and moisture deposits are formed on the panel, the buttons are jammed and do not work in normal mode. It is necessary to carefully inspect the panel, clean fat deposits and dirt, but very carefully, without fanaticism, so as not to harm your actions.

Each user must remember: the refrigerator has a very complex device, it is not necessary to independently eliminate problems in the electric circuit or electronic system, for this there are specialists in refrigeration equipment.