Room regulator Protherm THERMOLINK P
Room regulator THERMOLINK P (eBUS) for PANTERA boilers Version 18. Data transfer interface with.
Room regulator Protherm Calibri
Membrane room regulator. Gold plated contacts used in conjunction with a boiler.
Outdoor temperature sensor Protherm AF
Outdoor temperature sensor for controlling the outdoor temperature and optimising the boiler‘s operation. Article number.
Room regulator Protherm Exabasic
Room thermostat Protherm Exabasic temperature wired. To be used in conjunction with boilers from.
Outdoor temperature sensor Protherm S010075 for Bear KLZ, KLOM
Outdoor temperature sensor Protherm S010075 for Tiger Version 17 and Bear KL boilers.
Temperature sensor for Protherm SPF boiler
Boiler sensor, designed to enable control of a boiler, single boiler with a digital probe and a water heater.
Exterior temperature sensor Protherm QAC31/101
Outdoor temperature sensor QAC31/101. To measure the outdoor temperature (optimized for outdoor temperature in case of high temperatures).
Sensor of temperature of flowing water Protherm VF
Sensor of temperature of flowing water VF surface mounted flow temperature sensor complete.
Outdoor temperature sensor Protherm S010075 for boilers PANTHERA, HEPARD, SCAT
Outdoor temperature sensor Protherm S010075 for boilers PANTERA Version 18 and 19, HEPARD, SCAT Version.
Thermostat for Protherm FE 120/6 BM, FE 150/6 BM, FE 200/6 BM PLO, TLO boilers
Thermostat for Protherm boilers designed to work with boilers FE 120/6 BM, FE 150/6 BM, FE 200/6.
Protherm Exacontrol room regulator
Room thermostat Protherm Exacontrol is designed for Protherm boilers Tiger, Sc.
Room regulator Protherm Exacontrol 7. NEW
Room regulator Protherm Exacontrol 7 with 2-position control (On/Off). Program.
Room regulator Protherm THERMOLINK B
Room regulator THERMOLINK B(eBUS). for boilers PANTERA Version 19. transmission interface.
Boiler remote control unit Protherm GSM-Climate ZONT H-1V
GSM thermostat is designed to remotely control the operation of the heating boiler. Allows with.
Remote boiler control unit Proterm GSM-Climate ZONTH-1V eBus
The Proterm GSM-Climate ZONTH-1V eBus boiler remote control unit supports the temperature.
Protherm control panel for NO BIZON boiler
Protherm control panel for NO Bison series boilers controls the boiler with single and double.
Control package S-RG1
Control package S-RG1: Controller RVA43.222. 1 pc Terminal SVA43.222. 1 pc Submersible sensor.
Cascade controller Protherm KROMSCHRODER E8.4401
Cascade, digital, weather dependent control, two boilers with two-stage burner (or casc.
Protherm S-RG2 control kit
Control package Protherm S-RG2 Control package Protherm S-RG2. buy at.
Control package Protherm S-RG3
Protherm S-RG3 Weather control unit for boiler control with one / two-stage burner, for direct.
Thermostatic control valves
The thermostatic valve is a simple solution to obtain the desired temperature by mixing cooler water with warmer water. A view of the three-way valve is shown below:
Schematic diagram of the three-way valve in a heating system:
Diagram of connection of the three-way valve in the heating system
Wiring diagram for solid fuel boilers with thermostatic three-way valve:
Wiring diagram of the solid fuel boiler with a thermostatic three-way valve
Wiring diagram of the gas boiler using the thermostatic three-way valve:
Wiring diagram for a gas boiler using a thermostatic three-way valve
The thermostatic radiator valve allows you to control the temperature in the room by changing the flow of hot water through the radiator. They regulate the flow of hot water through the radiator, but do not control the boiler. Such devices must be installed to set the temperature needed in each individual room.
This idea should be considered as an addition to the thermostatic control installation. Also, such devices need periodic resetting and regular checks of their performance (every six months during the change of operating modes).
How does the Protherm Gepard work when connecting the thermostatic regulators?
When the gas boiler Protrem Gepard operates without a room thermostat, the heating of the premises depends on the setting of the coolant temperature.
When you connect a thermostatic regulator to the gas boiler Protherm, it is possible to set the desired temperature of heating. It must be such that the unit can maintain it, regardless of the temperature outside. The regulator will only control heating within the selected range.
Note! In the room where the room regulator is placed, the radiators can not be equipped with thermostatic valves.
A Protherm unit with a two-position regulator is able to maintain the set heating temperature. The boiler will receive a signal to turn on or off depending on the temperature in the room where the regulator is located.
If you connect a continuous regulator to the gas appliance, the output will change smoothly to maintain the set temperature in the room.
Room regulator will control the temperature in the room and send a signal to the unit to turn it off if the heat level has reached a predetermined value or on if the temperature decreases.
The most modern and precise is the equithermal regulation. It is made by thermostat with outdoor temperature sensor. When you connect such a device to the gas boiler, the latter will regulate the temperature of the coolant depending on the conditions outside.
If the unit is controlled by the equithermal regulator, it is not recommended to set the maximum temperature of the heating medium. this will significantly reduce the efficiency of the system.
Learn here how to make your gas boiler more economical?
Protherm room thermostat is an electronic device designed to automate the operation of the heating system. It provides control of the boiler depending on the temperature of the air in the heated rooms.
Slovak manufacturer of heating equipment produces a range of thermostatic regulators with different functionality. Including you can buy thermoregulators Protherm such models:
- Exabasic. regulator with two-position control.
- Exacontrol. model with two-position control, display for room temperature indication.
- Exacontrol 7. another device with two control positions. Can be programmed for daily and weekly programs.
- Thermolink P is an eBus connected device with a daily and weekly programming function.
- Thermolink B. connected through an eBus interface, it supports the modulation mode.
Room thermostats Protherm
Protherm room thermostats are devices that regulate the operation of the gas boiler depending on the room temperature. Boilers without a room thermostat switch on and off depending on the temperature of the water in the heating system, boilers with thermostats switch on and off depending on the temperature of the room.
It is necessary to remember that air in a premise cools down much more slowly than water in the heating system. With the Protherm thermoregulators there is no need to regulate the temperature manually, it is enough to set the temperature once on the thermostat. Boilers that do not have a thermostat waste 30% of their energy. For example, a 1C rise in temperature results in a visible overconsumption despite the already perceptible discomfort. The effectiveness of the device is obvious.
Protherm room thermostats automatically maintain a comfortable room climate. They provide a more gentle mode of operation of the boiler, reducing the restart cycles. The use of an uninterruptible power supply significantly increases battery life. Buying Protherm products, you significantly save on gas bills.
Wired room thermostat. Can be combined with Protherm Heating Boilers Scat, Tiger, Bear, Grizzly and Bison series.
- Temperature range: from 5C to 30C ;
- Output relay: 1 changeover contact;
- Operating voltage: 230V AC 50/60Hz;
- Switchable current: 10mA-10(4) A, heating, DC 30 W 10mA-5(2) A, cooling;
- Night temperature: Reducing by 5C;
- Hysteresis:
INSTAT PLUS
Room temperature regulator for Protherm Tiger, Skat boilers (room thermostat).
- Controller connection. Wired
- Regulation of room temperature (8-30°C)
- Programming of the temperature maintenance per day (six time intervals)
- Three standard programs
- Program “Protection against freezing”
- Battery charge status indicator
- Boiler operating mode and temperature indication on display
Termolink B
Room temperature controller for Protherm Gepard, Panther boilers.
- Room temperature controller with eBus.
- Ability to modulate mode.
- Regulation of Hot water temperature and room heating temperature.
- Antifreeze function protects when the temperature in the room drops below 3C.
- Information about errors on the display of the regulator.
- Correction of room thermostat and weather sensor temperature values.
- Vacation mode highest gas saving mode.
- Auto shut off temperature selection.
- Temperature regulation by external weather-dependent temperature sensor selection of heating curve (requires an external sensor).
Termolink P
Room temperature controller for wall mounted boilers Protherm Gepard, Panther.
- Programmable room temperature controller
- Select heating temperature Comfort/ECO
- Vacation mode
- Temporary room temperature change
- Program for 24 hours or 7 days
- Frost protection
Termolink S
Room temperature regulator for Protherm Tiger, Skat, Cheetah, Panther, Grizzly, Bear boilers.
- Heating temperature selection „Comfort“ or „Eco“
- Program for 24 hours or 7 days
- Frost protection” function
- Mode „Vacation“
- Wired connection to the boiler
- Easy to service
Protherm Exacontrol room thermostat functions:
Protherm
Protherm is one of the leaders of heating market that produces reliable equipment during 20 years. Protherm is now part of the Vaillant Group. Protherm is a strong player on the heating equipment market in Eastern Europe, annually manufacturing over 200 000 boilers. The quality of products manufactured in Skalica, Slovakia, is constantly checked, ensuring a long life of the equipment.
The wide range of products includes more than 95 types of heating equipment: gas boilers, oil boilers, electric boilers, boilers, water heaters and other heating equipment. The company offers a full range of spare parts for all products. All Protherm equipment is made of the best materials using innovative technologies that guarantees its maximum quality.
NTC boiler sensor for Panther 12 KTO, 25 KTO, 25 KOO boilers (version 2015)
Outdoor temperature sensor controls the boiler depending on the outside temperature. For Tiger, KLZ, KLOM v16 boilers.
Outdoor temperature sensor used to control floor standing gas boilers versions Panther, Cheetah, Skat, Bear.
Room regulator Protherm Exacontrol 7 (0020170571)
Two-position control (on/off)Programmable-
Room temperature controller Exabasic PT 6195 Protherm. For heating system.
2-position control (on/off). Dimensions (HxHxW), mm: 83x33x83.
Room temperature controller SRT380BY RU(0020261001) Protherm
Room temperature control system for heating and hot water preparation
Connection kit for B100MS boiler and KLOM boiler (0010006491) Protherm
Mechanical thermostat is designed to automatically set and maintain the desired temperature of the coolant in the-
Accessories for PROTHERM boilers
Room thermostats for room temperature regulation. Suitable for Protherm boilers.
Thanks to the thermostat is possible exact and convenient control of heating equipment with respect to the temperature of the environment. A number of Protherm room thermostats have the function of programming the temperature mode for a certain period, for example, reducing the temperature at night. Detailed functionality of the device is shown in the model description.
Model | Overall dimensions, mm | Note | Price, | Qty | Ordering |
Click to quickly compare this unit to other analogs | ZONT H-1V | 90x50x55 | GSM thermostat for control via telephone or internet | 18 139 | Buy |
Click to quickly compare this appliance with others | Exabasic | 83x33x83 | Room thermostat 2-way control | 2 425 | Buy |
Click to quickly compare this appliance with other analogues | Exacontrol | 95x40x96 | Room temperature controller 2-position control | 5 917 | Buy online at |
Click here to quickly compare this device with other analogues | Exacontrol 7 | 95x130x35 | Room temperature controller 2-position control | 8 536 | Buy |
Click here to quickly compare this product with others | Thermolink B | 90x36x96 | Inteis e-Bus, modulation mode option | 9 506 | Buy online |
Click here to quickly compare this product with similar products | Thermolink P | 97x35x147 | Room temperature controller for boilers Gepard and Panther series | 11 446 | Buy |
Click here to quickly compare this product with others | Kromschroder E8.4401 | 92x61x138 | Cascade regulator for up to 4 boilers | 66 639 | Buy online |
Thermostat connection diagrams for gas boilers. Which thermostat can be used??
Manual and automatic adjustment of the room temperature from modern heating sources is done with thermostats or thermostats.
They can be mechanical or electronic. Each of them has its own advantages and disadvantages.
All of them are similar in appearance, but the circuitry is different.
Let’s take a closer look at the peculiarities of connecting a thermostat to the gas boiler, its scheme, errors and possible problems in the operation of such devices.
To choose the right thermostat model, turn it over and carefully study the back side. Namely. Diagram, labels and pins.
If it says “Dry Contact” you have made the right choice. This is the designation of the thermostats designed to work with gas boilers.
The term “dry contact” says that in any state there is no voltage on these terminals. That is the 220V supply to L and N pads of the thermostat will not be connected with the dry contacts and the voltage will never get there.
Unlike underfloor heating thermostats, as in the diagram below. They have supply contacts (3-4) and the load (1-2) are connected directly with each other.
Why do you need this thing for a gas boiler?? Without such a programmer, the boiler after reaching the set temperature will run with a delay of about 3 minutes.
Turned on, worked, gained temperature and switched off. In three minutes it turns on again and everything repeats according to the new cycle. In a day the device will start about 200-240 times.
Thus, for the entire heating season the gas boiler will be turned on and off 40,000 times. By connecting a thermostat, you are several times reducing these commutations, thereby achieving not only gas savings, but also reducing the wear and tear of the heating equipment.
The logic of operation here is as follows. In the factory settings, the boiler heats water at the temperature of the coolant.
By installing the remote thermostat, we give it the command to heat water not as the boiler would like, but according to the settings of the thermostat, ie.е. for a particular temperature in a particular room.
With the normal insulation of the house and minimal heat loss, the gas boiler with a thermoregulator will run for only 3-4 hours a day.
If the thermostat after installation has had no effect on the operating time of the boiler, it is likely that the gas appliance is set at a lower temperature than necessary. The sensor simply does not have time to warm up to the necessary value and work, while t of the coolant has already reached the threshold.
In the instructions separately prescribe the minimum t on the boiler when using an external thermostat. As a rule, it should not be less than 65 degrees.
Initially at the heater is recommended to set the design temperature, which fully covers the heat loss of the building. When these heat losses are not known, for a standard heating system take values from 60 to 70C.
If you live in a relatively warm climate and do not raise the temperature of the radiators above 45C in winter, you will still need to increase the temperature to operate the thermostat.
Some people wonder what the point of installing a regulator is and how this leads to savings?
There is nothing to worry about because the temperature will be higher:
To connect the thermostat from the boiler terminal block to the Dry Contact terminals, you need to bring the two wires.
The recommended cross section of the copper conductors is at least 0.75 mm2, according to the manual.
The cable length to the location of the thermostat should not exceed 50 meters.
Look for the necessary terminals on the boiler itself in the manufacturer’s instructions, or be guided by the inscriptions on the terminals.
These terminals are usually located at the back of the control board.
Sometimes, however, manufacturers place them outside of the board.
Still some installers connect the cable here during the installation and take it out so the consumer will not get to the board and mess up something there. Since the thermostat is not yet installed, the cable ends are shorted.
By the way, be careful with this outrigger. Some consumers have encountered the problem of the factory intertwined wires, such as at Protherm.
In the end, everything starts to work as it should, but only when you connect it the other way round.
Initially, there is a jumper between the terminals. If the jumper is broken, the gas boiler simply stops working.
When connecting the thermostat, the factory-made jumper is removed and in its place is a cable laid to the installation location of the thermostat. Most importantly, no internal settings on the boiler need to be changed.
A low voltage control pulse (usually 24V) is sent through these terminals.
We have a control device (thermostat) and a slave (boiler). Between them, a set of constantly transmitting requests and responses via a low current line.
The principle of operation here is simple. by closing the dry contact, we thereby allow the boiler to work, by opening the contact, we interrupt the data transfer and prohibit. Closing and opening occurs through the thermostat relay, depending on the temperature setting on the device and comparing the current values in the room.
In case of tripping, first the burner is switched off, after a certain period of time (pump run-down time) the circulating pump is also switched off. Although in different models the algorithm of work of the pump can be different.
It is not desirable for the pump to turn off immediately after the thermostat is activated. In this case, set an offset of 5 to 10 minutes in the menu. Then the whole heating system will cool down evenly and the intervals of operation of automatics will increase.
On expensive models that support the OpenTherm protocol, you can control many boiler parameters via the remote programmer, not only switching on and off.
Here are illustrative examples of where to connect the thermostat for different models of boilers:
What happens if the thermostat fails? How would the boiler behave in this case?
It all depends on the position in which the dry contact remains. If it is closed. nothing will happen. The boiler simply starts on its last set program.
If open, the heating will not start and will not work.
Please note that the thermostat has no effect on the operation of the burner in hot water mode.
The 220V-phase and zero (L and N) voltage is applied to the power contacts of the thermo regulator. This can be done either from a separate socket or distribution box, or take them directly from the boiler itself.
On regulators with dry-running contacts it makes no difference which way the phase or zero terminals are connected, but on electronic models it does not matter where the phase or zero terminals are connected.of underfloor heating, this plays an essential role in terms of operational safety.
Because the wrong connection will only break the neutral conductor, and the phase will be constantly on duty on the heating cable.
By the way, for a gas boiler, you can use another simple type of regulator, which does not even have to supply 220V. For example, a Termec Emmeti mechanical thermostat or similar models.
You need to use only normally closed contacts 1 and 3, completely excluding the AC 220V (L and N).
The built-in sensor will close and open the internal contact when the temperature in the room changes. It doesn’t need any power. In this case all the logic of the heating is similar to the previously discussed.
Just do not forget that almost all mechanical models have a very large hysteresis. They can not create a comfortable temperature in the room.
So if possible choose electronic devices with WI-FI connection. Fortunately in our time the Chinese can find a very decent and inexpensive options.
Some models have contacts marked NO (normally open), NC (normally closed) and COM (general). Someone advises to connect through them, namely through NC and COM.
However, be careful, the thermostat is not the same as a thermostat and always study the instructions. They can also supply you with 220V AC voltage and you will run a phase on the control board where it is not needed.
Here’s a prime example of these Fluoreon and Beok multi-function regulators.
On multifunctional devices, the temperature in the room is also determined by a built-in temperature sensor.
However, they have terminals on the housing for connecting and external (Sensor). This is most often used for underfloor heating.
As is known, the air temperature in the room with a traditional system of heating on the radiators, heats unevenly. Near the floor it is lower, under the ceiling higher.
Due to the presence in the thermostats built-in temperature sensor, their height is regulated.

Place such thermostats should be at a height of 1,2-1,5 m from floor level and as far as possible from heating sources, including to protect from direct sunlight.
It is also not recommended to install thermostats in the corridor or kitchen.
Often consumers wonder if you can use a standard 220V floor heating thermostat to work with a gas boiler?
Suddenly, you can not find a special thermostat with dry contacts, and you already have a model from the floor heating. This connection is possible.
However, for this you will need to “decouple” the voltage 220V. In most underfloor heating thermostats, it comes on the power terminals and then comes off the terminals going to the heater cable. And as mentioned above, the gas boiler uses “dry contacts” that carry low voltage pulses.
If you connect the cable from the boiler control board directly here, you will cause a short circuit and damage your boiler.
To make it safe to connect to the circuit will have to add an intermediate relay or an additional contactor with normally open contacts.
From the thermostat terminals instead of the floor heating cable supply voltage of 220V to the relay coil (contactor), and already through its normally open contacts (1-2 or 3-4), you connect the wires to the gas boiler.
The principle of operation here is the same as discussed earlier. However, keep in mind the following peculiarity.
Since this thermostat is still for underfloor heating, it will most likely work according to the scheme: air sensor floor sensor. This means you need to install and set the temperature limitation on the floor sensor, which you will not have.
Therefore, you will have to unlink the floor sensor in the settings and leave only the air sensor in operation. How to do this, read in detail in the instructions for your model. There can be differences between devices.
For example, in Devi Touch for this you have to break a special jumper on the back side.
In order to avoid all these difficulties and problems, it is still better to choose the right model of thermostat.
If you have a water heated floor in separate rooms, which can be powered by the same gas boiler, you need a slightly different type of thermostat. It must be connected to the servos on the distribution manifold.
The reverse side of such a device looks like this.
If you have a normally closed servo drive, the cable leads to terminals 1 (Close or NC) and 3 (N-zero or COM). If normally open. 2 (Open or NO) and 3 (N-zero or COM).
The principle of operation here is as follows. When a normally open actuator is installed in the system and there is an interruption in the supply cable, the actuator opens the flow. In a normally closed, the situation is the opposite.
Do not be confused, this is not some kind of relay or el.magnetic actuator, which when you apply 220V voltage, it clicks and instantly switches to another state. This is a thermoelectric actuator which opens-closes the valve gradually.
Therefore, if you want to test the performance of such a device, do not be surprised that it will not immediately respond to the signal and immediately shut off the flow.
The thermostat power connection is made on the L and N pads. On the side terminals is wound cable remote temperature sensor in the floor.
Котел Protherm Jaguar JTV 24F подключение комнатного термостата
Thermostats Protherm. found 688 products.688 products
Control type: electronic, communication type: wireless, mounting method: overhead, minimum temperature: 5 ° C, maximum temperature: 35 ° C, underfloor heating sensor: not used, comutational current: 13A, protection class: IP30, programmable, air temperature control.
Wireless room thermostat consists of a thermostat placed in the living room and a receiver placed near the boiler. The signal is transmitted via radio and the thermostat is powered by batteries. This thermostat does not need any wiring.
True, underfloor heating regulation, air temperature regulation, suitable for infrared heating, suitable for electric underfloor heating
True, underfloor heating temperature control, air temperature control, suitable for radiator heating, suitable for water underfloor heating, suitable for infrared heating, suitable for electric underfloor heating
Control type: mechanical, communication type: wired, mounting method: surface mounting, minimum temperature: 8 ° C, maximum temperature: 30 ° C, underfloor heating sensor: not used, switching current: 10A, protection class: IP30, description: Room thermostat Protherm EXAB.

The Exacontrol automatic thermostat is installed for the control of heating systems without manual intervention. Doubts about the relevance of the installation disappear when in practice the following decreases by a third: water bills, fuel budget. Individual settings for each room temperature regulator.
Control type: electronic, contact type: wired, mounting: surface mounting, min temperature: 5 °C, max temperature: 30 °C, underfloor heating sensor: not used, protection class: IP20, programmable, air temperature regulation, suitable for radiators.
Element of heating systems for boiler equipment Protherm Compatibility of goods Combustion products thermostat Protherm (Protherm) (0020027536)
The Protherm EXABASIC room thermostat is designed for heating boilers and has a mechanical regulation system. With a wide range of operating temperatures and the air sensor. Maximum ease of operation and maintenance. Mounting provides.
Type of control: sensor, type of communication: wired, installation method: hidden, minimum temperature: 5 ° C, maximum temperature: 40 ° C, maximum load: 3600 W, the sensor floor heating: supplied, comutational current: 16A, protection class: IP21, programmable, adjustable.
Control type: electronic, communication type: wired, minimum temperature: 5 ° C, maximum temperature: 30 ° C, protection class: IP20, programmable, air temperature control
Control type: electronic, communication type: wired, installation method: hidden, minimum temperature: 5 ° C, maximum temperature: 30 ° C, protection class: IP20, programmable, air temperature control
Control type: sensor, communication type: wired, installation method: flush, minimum temperature: 5 ° C, maximum temperature: 95 ° C, maximum load: 3600 W, underfloor heating sensor: included, comutational current: 16A, protection class: IP20, programmable, adjustable.
True, floor heating temperature regulation, air temperature regulation, suitable for electric underfloor heating, description: Programmable electronic temperature controller for control of underfloor heating and other heating systems up to 3.6 K.
Control type: electronic, communication type: wired, mounting: surface mounting, minimum temperature: 5 ° C, maximum temperature: 30 ° C, programmable, air temperature regulation, suitable for radiant heating
Control type: mechanical, mounting method: surface mounted, floor heating sensor: included, floor heating temperature control, suitable for electric floor heating
Control type: electronic, installation method: hidden, minimum temperature: 5 ° C, maximum temperature: 90 ° C, maximum load: 3600 W, the sensor floor heating: complete, comutational current: 16A, protection class: IP20, programmable, temperature control heat.
ZONT H-1V is a room thermostat with its own SIM card, connected to the heating boiler. The commands to it can be transmitted from any phone, tablet or PC.The comfortable temperature is different for everyone. Some people like tropical heat, others believe that 20-22 degrees is more comfortable.
Control Type: mechanical, type of communication: wired, installation: flush mounting, minimum temperature: 5 ° C, maximum temperature: 40 ° C, maximum load: 3600 W, the sensor floor heating: supplied, current commutation: 16A, protection class: IP20, temperature control.
Control type: electronic, communication type: wired, installation method: into the socket, minimum temperature: 5 ° C, maximum temperature: 90 ° C, maximum load: 3500 W, underfloor heating sensor: included, comutational current: 16A, protection class: IP20, programmable, adjustable.
Operating thermostat (TY) for Protherm gas floor standing boiler. Original spare part
True, underfloor heating temperature regulation, air temperature regulation, suitable for electric underfloor heating, description: The Thermo Thermoreg TI-700 NFC is Europe’s first underfloor heating thermostat with technological control.
Control type: electronic, type of communication: wired, method of installation: into the socket, maximum temperature: 30 ° C, maximum load: 3000 W, the sensor floor heating: not used, the comutational current: 16A, protection class: IP20, air temperature regulation, suitable for.
Control type: touch, communication type: wired, installation method: flush, minimum temperature: 5 ° C, maximum temperature: 40 ° C, maximum load: 3600 W, the sensor floor heating: supplied, comutational current: 16A, protection class: IP21, programmable, adjustable.
Communication type: wired, mounting method: clamp-on, maximum temperature: 5 ° C, switching current: 16 А
True, suitable for radiator heating, suitable for water underfloor heating
The thermostat’s normally closed contact is used to control heaters that maintain the desired temperature inside the enclosure. Bimetallic thermostat mounted on DIN rail. Used to regulate the temperature inside the cabinet. The thermostat allows.
At the stage of design of the house there is a crucial question. Which heating system to choose, how to heat your home efficiently and not lose expensive heat. Choice of gas, solid fuel, electricity, innovative energy sources or a combination of these does not solve the problem.