Home Refrigerators Refrigerator Indesit hot motor does not freeze the reason
Refrigerators

Refrigerator Indesit hot motor does not freeze the reason

The refrigerator works, but does not freeze

When you feel a small electric discharge when contacting the household appliance body, you cannot use such a product. It is urgent to find out the cause of the breakdown on the case, for this there is a simple method: it is necessary to measure the resistance of the device of the device With the help of a megammeter

Disconnect the refrigerator and visually examine all the wires, if visually the malfunction cannot be installed. we begin to check the wiring alternate.

We connect the Earth’s wire from the device to the housing, and the wire “Fishing Lines for the Trimmer”. we alternately touch the wires going to the relay, thermostat, compressor. After the detection of the wire, where there was a breakdown, replace it with a new. Experienced masters advise. it is better not to risk the additional insulation of a faulty wire.

Flame of the refrigerator Indesit C138NFG

Two.chamber combined refrigerator with one compressor and electromechanical control. The NO Frost defrosting system is used in the freezer and the “crying” wall in the cold chamber.

The temperature regulation in the cells is independent, due to the presence of a magnetic valve on the refrigerant line between the freezer and the refrigerator. The faulty nodes of the Indesit refrigerator of this model, when the temperature in the cells does not hold, may be:

  • The thermostat of the freezer, if the desired minus in the freezer is not gained;
  • the upper thermoregulator, if incorrect temperature in the refrigerator;
  • sticking the magnetic valve of switching;
  • Freon leak or compressor failure.

The elimination of the causes is possible after complete diagnosis by specialists of the Center’s Service.

In the condensate removal system, clogging of the drainage system of condensate in the refrigerator is possible. The refusal of heaters in the knife system of the freezer will be expressed in icing. The fan will stop, clogged with ice. The non.working tiere of the hits will also lead to such consequences.

refrigerator, indesit, motor, does, freeze

A specialist can find and eliminate a malfunction, but before that you should defrost the lower chamber within a day. During this time, the refrigerator blades will be freed, and it will be possible to check whether the power network No Frost is working.

Why is the compressor of the refrigerator hot

Overheating of the motor is most often associated with the following reasons:

  • Camera overload. If the compartments of the device are clogged with products, the circulation of air flows and the movement of the freon is violated. The compressor begins to function intensively and overheating.
  • Incorrect placement of contents. You can not lean against the back wall of the container made of metal, glass, plastic. Otherwise, the motor will have to cool not only air masses, but also these items.
  • Placement in compartments of unheated products. In such a situation, the camera becomes sharper and the engine is forced to make the stops necessary to cool less often.
  • Neglect of the rules of defrosting. The thick layer of ice covering the walls of the device is one of the most common causes of the compressor heating.
  • Violation of the tightness of the camera. Frequent opening of the door or its loose fit contribute to the intake of warm air. Because of this, the motor experiences high loads and wear out prematurely.
  • The heat exchanger malfunction.
  • Damage to the tubes along which Freon moves and its leakage.
  • The breakdown of a thermal attenter, responsible for the timely stop of the system.
  • Wear of elements. Even the most reliable equipment after 10-15 years of active use requires the repair and replacement of individual parts.
  • The unsuccessful location of the unit. The refrigerator should not stand close to the wall or near heating devices.

What to do if the compressor of the refrigerator is hot

If the products are normally cooled, but the compressor of the refrigerator is hot, it is worth acting as follows:

  • Make sure that the refrigerator is correctly installed. To do this, you need to adjust its legs in height, measure the distance from the wall to the radiator grill (it should be equal to at least 15 cm).
  • Release cameras from products and defrost the device. When repeated loading, it is important to follow all the placement rules.
  • Extract a temperature sensor and test its performance by a multimeter.

If all the actions have not brought the result, it may be necessary to replace the compressor.

The device motor can become too hot for the same reasons why the compressors of the refrigerators are heated. If the check and the device and its restart after defrosting have not allowed to identify the malfunction, it is necessary to prepare the unit for repair:

  • Disconnect from the network, remove products, boxes, trays and shelves.
  • Break the pipe coming from the compressor and start the motor for 10 minutes. This time is enough for Freon to be in the capacitor.
  • Install a valve connected to a gas cylinder hose. Open the valve for 30 seconds to completely remove the refrigerant.
  • Change the gas pipe. It is recommended to give preference to copper elements. They can be soldered by a propane burner.
  • Cut the capillary expander, break off the pipe, disconnect the filter and compressor.
  • Extract a hot motor-compressor, remove the pipes that depart from it.
  • Set a new part and perform all actions in the reverse order.
  • Turn on the unit.

To replace the motor without appropriate skills is unacceptable. For this purpose, you need to contact a specialist.

Other breakdowns

In the design of Indesit refrigerators, additional nodes are used, involved in electrical circuits or in the contours of the given temperature inside the product. When the nodes are out of order, the upper chamber may not work, and error codes will be displayed on the display. If the refrigerator does not work after the power supply, then it is recommended to check the condition of the power cables, the plug fork and the unit of fuse fuses.

The fan does not work

In the design of the equipment, a fan is used, which provides uniform circulation of air in the chamber.

How to investigate and fix a fridge that is too warm

When the impeller stops on the display, error f04 is displayed.

It is possible to repair the Indesit refrigerator by checking the light rotation of the fan rotor and the power of the power circuit. The motor is checked by direct connection to the household network of alternating current. If the rotor does not rotate, then the fan replacement is required. If the impeller is spinning, then the problem is in power cables or the microprocessor control unit.

Tenn does not work in the cell

In case of refusal of the heating element installed in the freezer of the refrigerator with the No Frost system, the display is displayed a message from the form F07. To eliminate the breakdown, you will need to check the condition of fuse fuses, and then measure the resistance of the spirals with a test device. Independent replacement of the heater is not recommended due to the need to use a special tool.

Malfunctions of two.chamber refrigerators Indesit No Frost and your own elimination methods

If the Indesit refrigerator is purchased two.chamber No Frost, malfunctions can make themselves felt at any time, t. to. Even high.quality technique sometimes breaks for various reasons. To eliminate the problem, you need to learn more about the features of the device of all unit nodes. In some cases, the cause of the breakdown is easily eliminated, in others it is required to replace the main structural elements, but it happens that the Indesit No Frost refrigerator is no longer restored.

In cases where the upper chamber does not freeze in the Indesit No Frost refrigerator, it is necessary to check the operability of the fan that distributes air flows. When the impeller stops, air exchange is disturbed, only the wall adjacent to the radiator of the heat exchanger is cooled. The problem occurs when the tubes are destroyed and the refrigerant is leaving or with excessive radiator is overwhelmed (due to the breakdown of the automatic defrosting unit). Intended ice is able to jam or damage the impeller of the fan.

Other breakdowns

In the design of Indesit refrigerators, additional nodes are used, involved in electrical circuits or in the contours of the given temperature inside the product. When the nodes are out of order, the upper chamber may not work, and error codes will be displayed on the display. If the refrigerator does not work after the power supply, then it is recommended to check the condition of the power cables, the plug fork and the unit of fuse fuses.

The fan does not work

In the design of the equipment, a fan is used, which provides uniform circulation of air in the chamber.

refrigerator, indesit, motor, does, freeze

When the impeller stops on the display, error f04 is displayed.

It is possible to repair the Indesit refrigerator by checking the light rotation of the fan rotor and the power of the power circuit. The motor is checked by direct connection to the household network of alternating current. If the rotor does not rotate, then the fan replacement is required. If the impeller is spinning, then the problem is in power cables or the microprocessor control unit.

Tenn does not work in the cell

In case of refusal of the heating element installed in the freezer of the refrigerator with the No Frost system, the display is displayed a message from the form F07. To eliminate the breakdown, you will need to check the condition of fuse fuses, and then measure the resistance of the spirals with a test device. Independent replacement of the heater is not recommended due to the need to use a special tool.

The refrigerator will work with the same signs as the lack of freon if the capillary tube clogs. The difference is determined by the temperature of the capacitor and its heating areas.

What to do if the refrigerator is very freezing

The reasons why the refrigerator is very freezing or, conversely, does not provide the desired temperature, there are several: malfunctions in the compressor, hike, system of circulation of air and freon, a malfunction of the thermostat, thermal attewer, magnetic valve. Separately, you should consider the loose fit of the door, improper operation and configuration. Cooling can be excessive, weak, fast or slow. The freezer in the refrigerator can work wrong, all departments or one of them.

If the freezer with a complete No Frost does not freeze, then there is a breakdown in the technique, and professional help is required.

The freezer does not freeze in a two.compressor refrigerator

Two.compressor equipment allows you to control the temperature in the cells independently of each other due to individual evaporators and control panels. Therefore, the refrigeration compartment works fine, even when the freezer does not freeze. The problem is noticed by thawing products or a puddle on the floor.

Failure of freezer is always a breakdown? often yes, but there is a situation where the owners “helped” the technique.

What to check yourself

Some models of refrigerators with two compressors provide for disconnecting the freezer compartment. Check if you turned off the freezer accidentally or on purpose, and then forgot to turn it on. If the freezer is disabled, turn it on. Checked, and the camera is enabled? So the reason is malfunction.

Possible breakdowns of two.compressor models

Here are the freezers of the freezer, which our experts eliminate most often when the department does not freeze.

Morozin chamber motor. from 1900

The motor is responsible for the circulation of the refrigerant in the system. The main reasons for the failure of the compressor: due to the overload, windings (launch and/or working) burned or shortened, the engine jammed or damaged wiring, motor contacts. Instead of a faulty engine, a new one is put, the wiring and contacts are restored or changed.

From the experience of the masters!The refrigerator engine often fails due to overload. For example, in the summer, many owners of technology expose the maximum cold on hot days. The motor has been working for too long, overheating and breaks. We recommend not overfilling the refrigerator in such weather, and set the mode a little colder than usual. With such a load, the motor will cope without prejudice to itself.

Drilling relay of the frost compressor. from 1600

The start.up relay in the refrigerator stands on the motor and performs two functions: it helps it start and protects it from overheating. When the relay fails, the freezer engine does not turn on at all or turns on and immediately turns off. The start.up relay changes to a new.

Thermorerings thermostat or sensor of the freezer. from 1600

The compressor is turned on at the signal of the thermostat or temperature sensor. When there is no signal, the engine does not start, and the freezer does not cold. Or inclusions are very rare with long downtime, so the freezer does not freeze, but cools like a refrigerator compartment. Faulty thermostat in electromechanical models or a temperature sensor in electronic control models must be changed to a new.

Freon leak. from 1800

The refrigerant in the tubes moves through the closed system. Part of the circuit is responsible for heating the refrigerator housing along the perimeter of the freezer door. This is necessary so that the seal remains dry and ensures tightness. A leak in the heating circuit appears due to corrosion of a steel tube. In other places of the freezer contour of two.compressor leaks, there are rarely occurred.

With a leakage of the refrigerant, the freeaget motor-compressor works almost without stops, but due to a lack of freon cannot maintain a given temperature regime in the freezer compartment. When most of the freon evaporates, the freezer compressor stops turning on.

If the leak occurs in the heating circuit, the master cuts it and connects the tubes directly. Then the filter-dryer changes, the tightness of all compounds is tested by crimping. Further, the master vacuum the contour and season it with a refrigerant.

Blockage of the capillary pipeline. from 1800

The capillary regulates the supply of refrigerant to the evaporator under the desired pressure. The oil from the compressor is burned, and the products of its interaction with the refrigerant are deposited in the capillary tube. The resulting paraffins narrow the lumen, Freon hardly passes through the capillary, so the freezer compartment cools poorly, although the compressor works almost without break.

The blockage in CT is removed with special solutions, blown with nitrogen or poured with oil. Когда капилляр забит в нескольких местах или просвет практически отсутствует, трубка меняется на новую.

Spare parts are not included in the price and are paid separately.

If you are faced with the fact that the freezer as before works, and the refrigerator has stopped, then you need to check the following:

This happens in different cases, so you should disassemble the main reasons:

  • Simple malfunctions. It often happens that the owner himself is to blame for a breakdown, for example, at night I decided to eat a delicious sausage sandwich, and the door did not close it to the end. As a result, the compressor will work for wear, as a result of which it may break. Normal interruptions with electricity are also possible, so it is worth checking the wiring.
  • Zaror in the filter-dryer. This happens extremely rarely, mainly due to improper transportation. The technical characteristics of the oil in the compressor change during operation. Therefore, it can partially burn, if such a clot falls into the drainage, then it simply clogs it.
  • Freon leaks from the system. You cannot fix this malfunction yourself, it is better to immediately call the repair master.
  • Model decompression. Typically, the motor is operated at a pressure of 5-10 atmospheres, but due to natural wear, it loses such pressure. As a result, the work capacity of the refrigerator is lost in full or partially.
  • Damage or wear of the seal. It is very simple to check it, first you should visually inspect, and then put A4 paper sheet between the refrigerator and the elastic band. If you can get it freely, then you need to change it to a new one or put it in order.
  • The appearance of rust on the pipes and radiator. This phenomenon is dangerous in that the metal is slowly destroyed, and then the refrigerant begins to flow into the air.
  • The problem is in electronics. If you have a modern refrigerator with a display, then it has exactly the system diagnostics mode. And if the refrigerator is a regular No Frost, you have to suffer a little, as you have to call and check the boards and thermallane.

Conclusion. the contours must be made sealed and refrigerate refrigerator with a freon.

Why the compressor heats up

The compressor of the refrigerator is very hot due to many reasons. The most common among them are:

Refrigerator Not Cooling. How to Fix. What to Check [2020]

  • Incorrect filling of the device chambers. If the refrigeration and freezer compartments are clogged with foods, the circulation of air and refrigerant can be violated. Because of this, overheating of the motor occurs.
  • Placement of warm or hot products. For cooling air in this case, longer operation of the motor is required, due to which the temperature of the part may increase.
  • Long.term finding doors in the open state. Modern refrigeration units are equipped with an indication of door opening. If the device gives the corresponding signal, you need to pay attention to it and eliminate the fault. With constant leaving the doors in the open state, the motor quickly wear out.
  • Violation of the rules of defrosting. The formation of a thick snowy fur coat on the walls of cameras is the most common cause of compressor overheating.
  • Improper placement of contents in the chambers. Metal, glass and plastic containers cannot be leaned against the rear wall of the refrigerator. In this case, the motor should work for cooling not only air, but also objects.
  • Damage to the heat exchanger.
  • Refrigerant leak. Freon is released into the environment when the cooling system tubes damage.
  • The temperature sensor malfunction. The relay stops turning off the motor when reaching the desired temperature, which is why the compressor functions without stopping.
  • Wear of the electric motor. Even the most reliable German refrigerators after 10-15 years of operation begin to demand repairs. The reason lies in the wear of materials and elements of the system. Replacing faulty details helps to solve the problem with new.
  • Incorrect placement of the device. The motor overheating and does not allow the refrigerator to work correctly when installing near heating radiators. It is not recommended to put the unit close to the wall. Due to the lack of ventilation, the compressor overheats and eventually fails.

What to do

If the compressor of the refrigerator heats up heavily, but the device continues to freeze, you need to try to eliminate the malfunction. For this, it is recommended to perform the following actions:

  • Check the correct installation of the device. The refrigerator is aligned by regulating the height of the legs. The distance from the rear grill to the wall should be at least 15 cm.
  • Conduct a defrost. For this, the cameras are freed from the products and wait for the complete thawing of ice. When loading, follow the rules for placing products.
  • Check the operability of a thermal attemptor. The part is removed and tested using a multimeter.

If there are no appropriate skills, with your own hands can be a danger. In this case, you need to contact specialists.

Damage to the thermostat

If the refrigerator does not freeze, and the light is burning, no need to rush to throw it into garbage or call to the store where it was purchased with complaints. With the help of simple actions, you can determine the cause of the malfunction and return the previous functionality without financial costs. If you cannot eliminate the breakdown, but you will know why it appeared, repair work will become simpler, t.to. The master will be able to bring the necessary part to the house and install it in the place of the old.

Often, malfunctions in the work are associated with the lack of voltage in the outlet. To check this, just turn on another electrical appliance.

If the device has stopped freezing, and the light burns, the thermostat may have occurred. This sensor is located at the light bulb itself and provides a stable temperature inside the chamber or in a separate compartment.

Advanced models are equipped with several thermal sites. Когда температурный показатель достигает заданного уровня, система замыкает и размыкает электроцепь, вызывая запуск или остановку рефрижератора.

To assess the operability of the thermostat, it is enough to close two of its terminals:

As a result, an imitation of normal operation will be created when the temperature rises. If the motor starts, you will need to replace the sensor.

Faulty launch and protective relay

If the Indesit refrigerator does not work, perhaps there was a failure in the trigger and protective relay. Diagnosis of these components is carried out using a special electronic device. multimeter. The failure of the part must be disconnected from the electrical circuit and the resistance assessment. Any deviations from normal values ​​indicate damage to the part. If you do not own the skills of an electrician or are not sure that you can carry out such actions yourself, use the services of the workshop.

If you want to make a check with your own hands, make sure that the device is disconnected from the electric network.

Why is the industry fridge badly?

Indesit refrigerator stopped freezing and blowing do not cool. So it’s time to seek specialized help.

The main reason why the indesit refrigerator does not cold. Violation of the temperature regime. The problem leads to:

  • Faulty thermostat in the upper chamber.
  • Damage to the evaporative-capillary or heat tube, which provoke freon leakage. As a result, the unit does not cool properly.
  • A compressor or switching relay broke. Due to short circuits, electric elements fail.
  • The tightness is broken. The device door is incorrectly installed or the elastic band is adjacent, as a result, the Indesit refrigerator cools the food poorly.

Repair procedure:

In our service center, all problems will be identified and eliminated, due to which the Indesit refrigerator does not cool.

Timely appeal to professionals will extend the service life of your technique Indesit.

Diagnostics at home without contacting the service center

If you decide to inspect the equipment on your own, you need to control several points. The owner of the refrigerator must inspect the equipment and make sure of the following moments:

  • The device is installed directly on the flat floor;
  • The doors of the device fit tightly;
  • the device is connected to a serviceable electro.outlet;
  • It is desirable that the refrigerator has a separate power source.

Sometimes a rosette is to blame for a malfunction. You need to check its serviceability, then do the actual diagnosis of the refrigerator. Problems must be considered in a certain order:

  • “Defrosting” mode button. It is located in different places, depending on the model of the refrigerator: inside the freezer or on the case itself. If the owner of the equipment or family members accidentally touched this button, then the technique will switch to the “defrosting” mode and, accordingly, will stop freezing products.
  • Check the seal. It is necessary to inspect the seal around the entire perimeter of the door, both freezers and refrigerated chamber. The material of the seal can dilapidate and worn out during operation. Gradually, it becomes less elastic and is compressed. Sometimes the seal can damage the ice layer overgrown on the walls of the chamber. If damage to the seal is discovered, then the part of the part must be urgently replaced with a new.
  • Check the temperature sensor. In old models of refrigerators, temperature adjustment occurs using a special key or rotary disk, on which marks are applied. There is a control panel for modern temperature adjustment equipment in modern. It is necessary to adjust the temperature, the set value will reflect on the display, if after that the camera does not freeze, then the problem is in the sensor. You need to replace the part with good.
  • Check the condition of the motor. If after the defrosting the camera does not cool, you need to inspect the motor, which is located at the bottom of the refrigerator. Bring your hand and check how much the part has overheated. If too much, then, protection against overheating could be activated. To cool the motor, move the equipment from the wall. Fresh air access should be provided to the niche. After these manipulations, you need to turn on the refrigerator again. Problem solved? Excellent. If not, we continue diagnostics and look for the true cause of the freezer malfunction.
  • Measure the voltage on the motor. Using a tester, we carry out a voltage check procedure. If the tester shows the value of “zero”, then the probability that the thermostat has broken down. The faulty part must be fixed by giving it to the workshop, or installed a new.
  • An independent inspection of technology helps to identify a petty malfunction and quickly solve this issue. This is quite accessible to the owner of household appliances without special education. But if the initial inspection and diagnosis of the device did not give the desired result, contacting the service is inevitable. Do it as quickly as possible to prevent a serious breakdown.

Each of the faults of the refrigerators Indesit needs timely diagnosis and repair of the master. When the upper camera stopped freezing first, they are convinced that this is not a software failure, allowing the refrigerator to thaw for a day and restarting it. If these actions did not help, they are calling the service center for the repair of refrigeration equipment, since the own non.handbuilding repair can cause more serious breakdowns.

It is possible to extend the operational period of the unit by observing the correct temperature regime, timely doing the defrosting of chambers and preventing the compressor overload. Following the rules from the operating manual, it is possible to avoid unforeseen and unnecessary expenses for the repair of the Indesit refrigerator.

Indesit refrigerator– a refrigerator (main) camera is poorly cooled. Repair.

The freezer INDESIT No Frost Diagnostics and Repair do not freeze

Author

Laidred

| Denial of responsibility | Contacts |RSS