Home Electric stoves / gas stoves Is it possible to drown a fireplace stove with cones
Electric stoves / gas stoves

Is it possible to drown a fireplace stove with cones

Is it possible to drown the stove with pine wood: pros, cons, features of use

The problem of furnace heating in a private house is always associated with the choice of fuel for the upcoming heating season. Sometimes it is coal, but more often wood. The choice is small, so you often have to drown the stove with pine firewood. But, before making a reserve, it will be useful to learn about the problems and advantages of conifers.

Much depends on the device of the furnace itself. Is it possible to heat the stove with pine wood. yes, in a correctly folded brick firebox, you can burn any wood fuel. Some designs of stoves with flames of smoke gases allow you to drown even raw logs.

There is an established opinion among the owners of stove heating houses that it is impossible to heat pine wood, even if there is nothing more. Nevertheless, coniferous. pine and spruce logs often fall into a wood warehouse. Many will drown them, not even suspecting that pine and spruce go to the furnace furnace, in addition to birch churoks. And there are certain advantages in this:

possible, drown, fireplace, stove, cones
  • Heating costs are reduced. Drowning pine firewood is about half as much as acacia, aspen or oak.
  • Due to the high content of the gum, resin and cellulosoliganin, pine firewood flare up faster and burn deeper with a minimum amount of ash.
  • A fairly high heat.intensive ability, so you can drown along with maple or acacia.
  • Pine firewood absorbs moisture less.
  • When burning, a specific coniferous smell of life is distinguished.

Before drowning, firewood still needs to be prepared. Pine wood is cut and even pricks an ordinary ax is much easier than if you cut oak or acacia. This means that you can cut the logs of the desired size and weight so that the furnace furnace is filled evenly.

Another important plus. pine firewood can be prepared several years ahead and drowned with them, without fear that the reserve is not enough for the winter.

Unlike pine and spruce logs, deciduous rocks are stored much worse. Often, with improper storage, wood breaks down, destroyed by bacteria and fungus. Drowning with such firewood is obscure and unprofitable. Pine or spruce suffer from pests less thanks to high life content.

Features of the use of pine firewood

Everyone who has to drown the stove with wood knows that for ignition you should always have a dozen or two well-dried pine logs in stock, and necessarily from a young tree. Even if you do not drown a spruce or pine, finely chopped beam will come in handy for ignition of the furnace.

If you plan to heat the stove with a dry pine, then you need to consider the following:

  • It is better to choose old pine blocks with a large thickness of the sapwood.
  • Before chopping firewood, sapelon should be cooked or cut off if possible.
  • A less dense core is used in the furnace.

Sapelon (outer layers of the barrel) cut for ignition. It is inconvenient to heat it due to the high content of volatile substances and resins. The core gives less heat, but it also burns more evenly. Therefore, if you plan to drown the oven with pine wood, it is better to buy fuel in logs.

Dissolve the pine with a circular saw on the hump, a board and core. Boards can be used as building materials, and healing, scraps and core, drown the stove. Sometimes in rainy weather the hosts intentionally throw a couple of pine logs into the furnace. A special fragrance of the gum appears in the air, well masking irritating smells from burnt soot in a chimney.

Which stoves can be drowned with pine wood

The rule is simple. the higher the flame temperature in the firebox, the less soot is deposited and the resin is condensed on the walls of the chimney. Therefore, traditional stoves of prolonged burning, as well as Russian and caps, do not recommend drowning pine wood. The more economically the stove, the less it is adapted for the use of spruce and pine logs.

It is not recommended to use spruce and pine firewood in fireplaces, in which the chimney pipe of the bath is combined with a stove or the main stove. Ordinary fireplaces with a straight chimney and cast.iron cut can be drowned with a pine.

Coniferous breeds allowed to drown bourgeois from heat.resistant alloy steel and cast.iron fireplaces. Small and soot deposits fall on a set of furnace chamber and the initial section of the chimney. Therefore, after the metal walls of the furnaces are heated, all sediments burn out. Then you can drown anything, at least pine firewood, even raw branches with a moisture content of 30-40%.

When using firewood from coniferous wood, 2 conditions must be followed:

  • The last portion of logs laid in the stove should not contain pine trees or spruce. You need to complete the furnace with dry alder or aspen firewood.
  • The doors blew (ash) and the firebox itself should be closed tightly, without cracks. Warmed resins and lovice when overheating can be strongly sprayed with tar and scum.

Another nuance, if drowned with pine firewood, even mixed with deciduous rocks, then the chimney and lower furnace chamber will have to be cleaned at least 2 times a year. And besides, periodically burn the soot in the pipe using special additives to firewood.

If the house is large, then given the difference in price, drowning pine wood is cheaper than ordinary wood. Although the volume of work on maintenance of the furnace and chimney increases several times.

Flaws

If you do not know the specifics of coniferous wood, then there may be plenty of problems with pine logs. Although most of the shortcomings are successfully overcome, there are serious disadvantages that you need to know before making a wood reserve for the winter.

A huge amount of life

This means that it will not be easy to chop freshly sawed chocks. Even a sharp corner with a polished blade after a certain time is covered with a plaque of resin. It’s hard to cut with such a tool, the garbage and chips sticks. You have to periodically wipe the blade with an oiled rag.

In a cold firebox, the resin melts and flows into the grates and ash. All this sins and often clogs the grill, thereby blocking the normal flow of air. Also, couples are condensed on the back of the door.

If you open the oven, then the metal surfaces will be covered with a tarry coating of black. The same exactly the film settles inside the chimney. Especially a lot of accumulates in steel pipes. The worst of all the resin “clings” to modern ceramic chimney.

A large number of volatile compounds

When the pine or spruce is heated, thermal pyrolysis of wood occurs. Flying substances are released, among which there are a lot of carbon monoxide, alcohols, scum. This part of the gases is carried into the pipe.

The most dangerous are phenol and volatile products of incomplete decomposition. They appear if the temperature in the furnace is not high enough or burning occurs with insufficient air supply. Then the aroma of Zhivitsa first appears in the room, then. an unpleasant bitter smell of creosot (a characteristic smell of wooden railway sleepers).

In this case, the room needs to be ventilated and at the same time check whether the door is tightly closed on the furnace. Sometimes you can see a sizu stream of smoke that beaches through the gap in the furnace or even in the brick laying of the furnace. Such a stove needs to be urgently repaired.

When burning pine or spruce, a lot of soot forms. Most of it is deposited inside the chimney throughout the height of the pipe. Soot with resin sticks well to the cap and even seeps between the pipe sections.

Smol and soot plaque are dense and viscous. It is not always possible to completely clean the soot deposits with a ruff and brushes, so you have to stove regularly with aspen or oak wood.

It is possible to heat the stove with pine wood if the design of the firebox and chimney itself is adapted for such fuel. Sometimes you can find furnaces converted for the use of spruce logs. They use the injection fan, so you can easily burn low.grade coal and trimming pine branches. But you have to clean the stove much more often than on ordinary wood.

Share your experience in using pine firewood, what problems arose and how they solved. Save the article in bookmarks so that useful information is at hand at any time.

Fire characteristics

About the pros and cons of different firewood, it was already discussed in the article of firewood. good and different. But some nuances should dwell in more detail, what we will do now.

Different wood of wood has a different heat.intensive ability

If we compare the heat.intensive ability of firewood from various wood, then in terms of the mass (or, in other words, weight) it will be almost the same for everyone. But this is the calculation of the mass. But different breeds differ in different density, so with the same mass, the volume can be different. So it turns out that with greater density the same volume will be heavier, which means that it will provide greater heat. Understanding this, you can figure out which firewood is better to choose. We conclude: the heavier the woodpecker, the more heat it will give.

This, of course, is true only in relation to dry firewood. We do not talk about wet. they flare up more difficult than dry, and give less heat during burning. Only firewood from acacia (both dry and wet) burn in a preheated firebox almost the same.

Dry firewood burn hotter

  • The record holder for heat.effectiveness. oak: 3.2 kcal/dm ²;
  • Somewhere nearby there are ash, mountain ash, beech, apple tree, acacia-3.0-2.7 kcal/dm ²;
  • Birch, maple, pear, chestnut. about 2.6 kcal/dm ² will warm you approximately equally;
  • But pine, linden, alder will give only about 2 kcal/dm ²;
  • You will receive even less heat from firewood from linden, willow and aspen. 1.8 kcal/dm ². They will burn quickly, almost without coal;
  • fir and poplar will give 1.6 kcal/dm ².

It is better to choose wood firewood with dense wood

If you got firewood from a rabor, then you are a happy owner of blessing fuel with a very high heat transfer. The roasts of the ancient Chersonesos were filled with grab coal. These firewood have always been valued among blacksmiths, founders, potter, bakers, because they burn for a long time and do not smoke.

If you are faced with a choice of ascinal or pine, not very rich in calories, then you should give preference to aspen. She, unlike a pine, leaving significant deposits on the inner surface of the chimney and the furnace, not only does not pollute them, but also helps to clean from these deposits, highlighting specific gases during burning. True, it is quite difficult to melt the aspen. There is even a saying: “Aspen does not burn without kerosene” 🙂 But it will not be at all difficult to throw in the already burning furnace.

Osina firewood. Photo from Drovasek72.ru

Just like aspen, soften soot in a chimney alder firewood. They burn hot, almost not at all smoking. For these properties they were nicknamed the royal. They are very fragrant, so they are often used to smoke meat and fish.

Easily flare up and burn with even long flame birch firewood. They fill the room with a slight aroma (it is only a pity that after three years of storage it becomes less intense). Birch firewood, although they give good heat, but if the air is improperly, they can smoke to the furnace. And along with smoke, tar and birch resin are filtered into the chimney (it turns out, there is such a :)) tar abundantly settles on the pipe and can even drain down if the pipe is thin and cold, not insulated from the outside.

Firewood from cherries. Photo from Drovavovoz website.ru

Where there are old fruit gardens, you can get hold of excellent thrummy. Firewood and pears are easily chopped, while burning well and fill the room with a pleasant aroma. “Tasty” smells and cherry firewood smell. But they smoke strongly when burning, because the cherry contains resins. For this reason, cherries and plum wood are better not to use for picnics.

Cleaning chimneys and furnaces

No matter how beautiful and blessed firewood, on the chimney and in the chimney channels of the furnaces, soot is still postponed. It must be periodically removed. This is very important, because there are frequent cases when Sazha burned out and brought to the house. Soot burning temperature is very high. 1100 degrees. Not every chimney can withstand it. it happens that the pipe just explodes, causing a fire. Therefore, periodic cleaning is necessary!

Pipes and chimneys must be cleaned!

They are engaged in this case, of course, chimney sweeps. You need to call them quite often. But you can reduce the number of visits using preventive means to clean the chimneys.

One of these funds is very commonplace. potato cleaning. About half a gear of dried cleanings, and if the oven is large, then the bucket must. Glaza, like aspen firewood, is allocated during the combustion of potato starch and help the chimney cleanse themselves with the chimney. This technique will not save you from cleaning at all, but will undoubtedly reduce its multiplicity.

Pipelines cleaned the channels using special ruffs. They climbed onto the roof, gradually lowered this device into the pipe and with smooth movements scraped off the soot. Then fell below and cleaned (through special holes) smoke channels in furnaces.

Nowadays, the chimneys themselves have changed and the methods of cleaning them

Now a lot has been improved: all kinds of devices have appeared to clean the chimneys from below. using an elastic steel cable. But these devices are expensive.

The summer residents managed to invent an original and almost free chimney sweep. They just take a well.known plastic bottle, make vertical incisions along the walls (from the neck to the bottom) at a distance of a couple of centimeters from one another. Then they spread through the bottom and neck of the bottle of the rod, attract the bottom to the neck along the axis, fix the brush.cutting bottle formed from the cut walls with a pair of nuts, suspend the load.

Homemade brush for cleaning chimneys. Photo from the site I.ytimg.com

If the pipe of a rather large diameter, then instead of a liter bottle, take a plastic 3-5-liter, remove the bottom, simply cut the walls into strips and bend them. Everything, Yershik is ready. It remains to tie a piece of brick on the rope, and you can become a chimney sweep.

Progress does not stand still: modern professional chimney sweeps use not only traditional mechanical methods of pipe cleaning. Special vacuum cleaners appeared for these purposes. There are even briquettes or powders for the preventive cleaning of chimneys that work, in general, like potato cleaning, only more efficiently.

Chimneys cleaning. Photo from Dom-Kotlov.ru

The smell after them is not very pleasant, but this allows you to reduce the number of visits of the masters.

You can find a large assortment of various means for cleaning chimneys from soot and soot in our catalog, uniting the proposals of many large garden online stores. View a selection of chimney cleaning products.

Coniferous firewood. pine, spruce, larch

A characteristic crackling of logs in the fireplace, bright sparks, now and then scattering around. signs of burning coniferous firewood. Like birch, they give a lot of heat, only burn much faster. But for the unique resinous aroma, which is felt when the furnace with pine or spruce logs, you can forgive many shortcomings. Only now you will have to follow the hearth more carefully: the “shot” spark is able to fly out of the furnace and cause big troubles.

Coniferous firewood is appreciated for a unique resin.colored aroma

Spruce fires are not as hot as pine. keep in mind when the workpiece. Larch wood are used quite rarely. not so this breed of wood is common in our country. But if you come across such logs, remember: burning, they form a lot of carbon monoxide, so in no case do not rush to close the damper and take care of good ventilation. By the way, soot and soot from tarry conifers on the walls of the stove and chimney will settle no less than from birch.

Olkhov firewood. royal

If you manage to get hold of such offships. consider that you are lucky: they burn hot, almost without smoke and soot, but with a unique aroma with healing force. It is believed that a bathhouse on alder wood is a true remedy for colds. And in the old days, they say, it was Olchu who was chosen for stoves in the royal chambers and rich manors. Appreciate alder firewood and lovers of households. Olhas fresh saws have red-orange color, so the logs will look bright.And unusual. Ferse from alder firewood has healing power

True, this wonderful tree has one feature that you can not find out, buying ready.made logs: everything said applies to the firewood from alder, which has grown in a dry place. But the marsh and smoke can, and in the bath a heavy heat is heavy.

In our catalog, where the goods of large garden online stores are presented, you will find comfortable bags for carrying firewood, stands for their storage in the house, cornconsus and other necessary accessories. Choose useful accessories.

Fruit trees

Fruit trees also have good properties necessary for the hearth. They will be used for both furnaces and barbecues, smoke. Fruit wood has a very good aroma.

When cutting fruit trees, it is advisable to store this wood and then use for the stove spacing. She will also go for the barbecue and for the smokehouse. Most often, this wood can be purchased when cutting old gardens. The most common trees for kindling are cherry or apple tree. Cherryflies of soot give more, but they are kindled very well. Apple.tank blocks do not give a lot of smoke, so they are considered the highest quality fuel.

The healing properties are attributed to many fruit trees, for example, an apple tree and a pear of certain ages.

Coniferous firewood

In coniferous rocks, tarry substances are kept in excess, give a lot of smoke that is very clogged with the chimney. Such logs are burning very quickly. It is better not to take coniferous rocks for the furnace. Drowning stoves and fireplaces with logs of coniferous wood should be very careful. But even with their shortcomings, such firewood is popular.

Sometimes a needles are used for the furnaces of baths to fill the oil trees with oils of coniferous trees. The healing forces of pine and spruce help to recover from diseases of the respiratory system and calm the nervous system.

On a note. Sometimes you can observe how the owners of the household use the furnace as the disposal of unnecessary paper and other garbage, thick black smoke is falling from the pipe. In addition to the fact that this leads to a deterioration in ecology, you should know that chimney channels are clogged, covered with a thick layer of soot.

What firewood for the furnace are considered “correct

Not all tree species of trees are the same firewood. One breed is good for construction, the other for smoking meat products, the third for heating. Therefore, for any firewood, certain characteristics are characterized.

An important place in the process of the furnace is the heating structure. For example, pleasantly smelling rocks are used for fireplaces, but without a large amount of resin, since this substance is the cause of the possible smoke of the room. Plus, the resin causes “shooting” firewood, which can cause a fire.

In addition, after the complete combustion of logs, a small amount of ash should form.

Important! These properties are determined not only by the breed, but also by the quality of drying of firewood, since, for example, the use of raw material is fraught with poor burning and highlighting in a large amount of smoke.

Therefore, in order to ensure the high quality of the material for heating, the trees must be cut down in the winter. This is due to the movement of juices in them, which is minimal. in winter.

Advice! It is not recommended to use firewood in the winter in the summer in the summer, since with the onset of cold weather they will still be wet.

Properties of different tree species

Usually, for furnaces in furnaces, firewood firewood are used, which differ in a fairly dense structure.

Therefore, they have a lot of heat transfer, they burn well. This group also includes most fruit trees, the burning of which is accompanied by the release of pleasant aromas. The names of firewood correspond to the names of the trees.

Oak

First of all, oak is the personification of power, the relics of the ancient Slavs. This tree is also now appreciated. It belongs to a solid, elite breed.

Advice! If you want to cook real pizza, then for this you should use oak firewood.

Typically, for fuel, business wood or medium.aged trees are used for fuel. They are able to give a lot of heat for a long time. Unlike young analogues, their heat is strong, and the room is not filled with a pungent smell of a smoldering tree.

After the combustion of firewood from too old trees, usually a lot of ash remains, and the heat transfer is smaller, and the room can be filled with “heavy” air.

Important! If the firewood is really good, then after their burning they are filled with an excellent tart forest smell, which causes an increase in the general tone of the body and positively affects the state of health.

Linden

Firewood of linden. ideal for bath stoves. And this is the true truth, since the melted oven can be compared with the generator of unusual aromas, which have a beneficial effect on the respiratory tract and the lungs. Such wood is not easy to incite, but if it flared up, then the heat persists for a long time.

They are able to maintain their thermal qualities for no more than 2 years.

Birch

Both oak and birch belongs to a solid breed. Therefore, birch firewood is excellent fuel for furnaces. Although, according to their thermal characteristics, they are inferior to oak wood by about 10%, but they exceed pine analogues by 24%.

The disadvantages of birch wood include the presence of a large amount of resin, which contributes to the accumulation of soot, both in the furnace chamber and in the chimney. The resin is mainly concentrated in the bark.

Use A Tea Bag And You Will Never See Spiders Or Mice In Your House Again!

Advice! Helpers from soot with soot is helped by aspen firewood.

When using birch firewood as a fuel, the room is immediately filled with a unique aroma. In addition, there is a complete disinfection of air. Therefore, for the prevention of respiratory diseases, it is recommended to drown with birch wood. Although it must be taken into account that the healing properties of wood saving for 2 years.

Aspen

Probably few people are interested in aspen firewood. Why, you ask? The answer is simple: such wood is not easy to kindle, gives very little heat that instantly turns into ashes, and they burn too quickly, giving too little heat (about 40% less than birch). Therefore, if a problem arises, and which firewood can be used for the furnace in the furnace, then know: any, but not aspen. True, they have one advantage: with their help they are cleaned by chimneys, since they do not leave the minimum number of soot in the process of combustion.

Olkhov

“Tsarist”. so they also call firewood from alder sulfur. Why do they have such a Honor? Even in historical chronicles it is mentioned that alder wood was drowned in the furnaces of the tsar’s chambers.

In the process of combustion, they practically do not distinguish soot, and in terms of heat transfer. only a little inferior to oak and birch.

Olkhovaya wood has little resin, it is easy to light it, gives a lot of heat. Since smoke is almost not distinguished during combustion, such firewood is carried out “in black”, which is sometimes still used in baths. Plus, during the burning of such firewood, the room is filled with a pleasant aroma that is effective in the treatment of a cold.

Important! If you use alder firewood for the furnaces in the furnace, then the whole family will be cheerful, energetic and healthy. Checked!

In addition, they make a great heat for cooking barbecue. With the help of alder sawdust, meat and fish dishes smoke.

Dried wood can be preserved, without losing their thermal and other qualities, for 3 years.

Willow and poplar

For furnaces furnaces, both firewood and poplar are used for furnace. They are distinguished by rapid burnout, slight heat transfer. Therefore, it will not work to save on them, given the low cost, since a lot of firewood must be burned to obtain a large amount of thermal energy.

Willow and poplar are attributed to low.grade wood. It is also relatively cheap. Therefore, firewood from these trees is used in extreme cases. if there are no other options.

From fruit trees

Such firewood is used quite rarely. After all, the cutting of the old garden does not always pass, or. the wind broke a pear or apple tree. Despite this, they are most often used for furnaces in stoves-stone. In the process of burning firewood from fruit trees, a wonderful aroma spreads around the room. They are characterized by good heat transfer, with their help you can quickly heat the room.

Комментарии и мнения владельцев to the record (p. 2)

I love cones. all the most diverse, drag home from different places, even brought from the Crimea, walked under the pines and collected. As in childhood, my grandmother put a samovar on bumps, so I’m doing it now in the country. I lay out under roses, in the fall I close all the vases with cones for the winter. For Christmas and New Year, I use cones in compositions.

Is it possible not to love sh-i-sh

I use pine (spruce) as drainage when planting rhododendrons and hydrangeas, crush them and mulch the same crops along with pine dump.

About the samovar is understandable. And why, interestingly, you can’t mulch them, unlike pine? After all, they acidify the soil that some, that others?

-It seems to me- this is the least suitable material for mulch! They- firm, resistant to decay of any kind Better- with firewood!

Tatyana, spruce adds acids to the soil, but in general, in composition, when decomposed, they are worse than pine, do not like plants.

But don’t cones acidify the soil? I have cones nearby. the forest is full, but the soils are sour on the site, in some places a horsetail rod. I had to introduce dolomite flour in the fall for deoxidation. And so it would be great to fall asleep with cones all the earth under roses!

Yes, they acidify, but they need to be used for rhododedron, and all coniferous, and with the rest you can do otherwise: cover some covering material

Condoing with cones, I mulch the soil around roses, just scatter a layer of ash under mulch, it neutralizes severe acidification. The fact is that in the coniferous impudent there are a lot of nutrients. And I slowly drag him from the forest, and bumps too. And mulching hydrangeas is the sweetest thing with them, they love acidic soils.

That’s what I have no shortage with is with ash). I bought a site seven years ago with an old garden. apple trees, plums and cherries have to be cut regularly, or even clean the trees. Branches, trunks. I burn everything. And the grass after weeding, the stems of high weeds, if you dry. also in a fire, grass ash is considered the best. And when they demolished the old master’s hut, the whole wood was beaten to capacity with firewood. But, probably, you can drain from the forest a little bit of branches? We have a lot of foller in the forest.

The Cost Of Operating An Illegal Wood Stove

A lot of cones nearby in the forest, the soil is also acidic, the crafts are done in childhood as I understand it, that neither in compost, nor fertilizer

It is very useful for these cones to walk with bare legs or in socks, if unreasonable. There are many active points on the feet, t.e. We do a spot massage, just do not overdo it over time And one more. recently I learned from a friend that the decoction of these cones dilutes blood, it uses them instead of the medicine cardiomagnil.

Yes you can make a massage rug: there are several lines of fabrics on a layer of cones, gradually remove the layer, training to the level of yogis))

If only special for magicians such special with springs, fall into the plank, and the visual effect, as if they really come

No, I went with my back on 10 centimeter nails. If they are often stuffed, then how you go to needles, the same feeling.

With such posts, you should give warnings “not to repeat at home”. And then it happens that summer residents heard herself and they themselves begin to repeat the experiments, someone will fall on the nails And then they are tightly driven, t.e. How sandpaper turns out, and if a little less often there will be a torture camera as after weeding.

Judging by the “My Sports Hall”, summer residents do not really seek to repeat the experiments for health. and more recipes are discussed and repeated. The competition again started “what to eat to lose weight”, there would be no “my experience of a lump” without recipes and with recipes for a healthy life

Forgive me, please, but my deceased father told my stomach sister when she told him that he eats little. if the pig was not to eat to be full, she will not be a pig.

possible, drown, fireplace, stove, cones

I’m not a bucket of cones at a time in the stove, but a little bit a little. Burn very well. In baked wells, I did not notice any special tables from this!(we clean from soot periodically)

And I have no one to clean, so I amware of cones, pine branches that I remove from shelters in the spring, etc. burn in the stove. On the contrary, I add a little aspen to clean the chimney.

For 25 years we first cleaned the well.stove. Osina pulls everything, but I don’t know 100%, t.to.Information only from print.But the Russian samovar was drowned with cones.And no one mentioned the resin from them.

In order to clean the chimney from the possible accumulation of soot, you need a higher temperature than those firewood that you constantly use. Osina has a burning temperature lower than the birch. So you only add an even bigger problem. It was not for nothing that the village for the winter was prepared precisely by the birch, and in the summer. in the summer you can also be drowned with a multi.folk. You probably heard about “royal firewood”. They burn with a very high temperature, which made it possible to heat the halls in the castles of ancient knights. So it was firewood from alder. The question is where to stock up so much? Although there are a lot of thickets of alder, but the trunks are thin and therefore to stock up such firewood in large numbers is problematic. But I burn it in the pipes. So that there are not so many alder firewood. Well, if the pine cones are well dried on the same furnace, then because of the presence of resins in them, they will burn-only so There is another advice, but I’m afraid to voice u-Dachi!

It is about “burning, pumping” the pipe. Not every oven is good for that. If there is an opportunity, without melt the stove, “dilute the fire” on the “pancakes” closing the pipe from 5-10 newspapers, then, maybe again with the chips of birch (alder). The method is fire hazardous. But effective! If only the pipe itself was in perfect condition. Since the soot in the pipe may ignite. And this is fraught with consequences. And never burn any plastic in the furnace. For he covers the inner walls of the chimney with a difficult tolerance. Like glass, only black. But at sufficient temperatures, it is very “hot”. The pipe should be in full serviceability! By the way, you can melt the snow in the pipe after a long “non.visit” of a country, for a long time not heated house. The so.called “snow traffic”. Good luck!

Low heat of combustion

One of the most common arguments of the opponents of the firebox using pine firewood is that when they are burned, much less heat is released than when using wood of other species. In fact, according to the results of research, the heat production of wood depends on its humidity, and not on the breed. The amount of heat released during combustion of the same amount of firewood of different types ranges so insignificant that this factor is not necessary to consider this factor.

However, Mendeleev also introduced such a thing as heat production. It was proposed to understand the temperature that is formed in the firebox of a standard furnace when burning a certain amount of fuel. This parameter is calculated in relative units, a mountain maple is adopted for the standard, when burning which is reached a temperature of 1200 degrees Celsius.

So, according to such a parameter as heat production, the pine was at the end of the list of known wood species, which are most often used as fuel material. Pine anthrust is only 52 % of mountain maple heat. For comparison, oak and birch indicators are much higher. 70 % and 68 %, respectively.

These data are largely confirmed by practice. So, if you load the furnace with pine wood, then the combustion process goes well, firewood quickly flare up and turns into coals and ash, but the heat is much less formed than when burning oak or birch.

From this point of view, it is much more profitable to drown acacia, hornfrend or firewood from fruit trees, for example, apple trees, pears or cherries. However, this does not answer the question of whether it is possible to heat the stove with pine wood, because the low heat production of the pine does not exclude its use as fuel under various circumstances.

Safety of pine firewood

But if you consider the question of whether it is possible to heat the stove with pine wood in terms of process security, then a slightly different picture is emerging here. After all, conifers contain a large number of different resins. Therefore, when burning, they will produce a lot of soot, which can settle on the elements of the furnace or on the inner surface of the chimney.

Such deposits adversely affect the thrust, the efficiency of the furnace or solid fuel boiler is reduced, and such an indicator as the degree of combustion of firewood worsens. In other words, when the chimney is overgrown, after combustion of logs, there is much more coals and ash in the firebox, and in the process of burning more incomplete combustion products are formed, which, in turn, also penetrate the chimney and settle in it. Thus, the further, the more active the stove pipe will be clogged.

In a fire department, soot is a rather dangerous product, since under certain circumstances it can be ignited by. At the same time, the burning of soot and resin deposits inside the chimney may be accompanied by an explosion, and this is already fraught with the destruction of the furnace. Posteries made of a metal or asbestos.cement pipe are especially susceptible to such danger. When using such structures of the furnace, you should especially think about whether it is possible to heat the stove with pine firewood.

Studies show that the most actively process of deposition of tar and resins on the internal surfaces of the furnace and the chimney is in cases where the smoldering mode is installed in the firebox. This happens with a closed blunt and smoke valve. Therefore, in order to avoid problems, it is recommended to carefully monitor the condition of firewood loaded into the oven.

The situation with fire hazardous deposits is aggravated by the fact that soot and resins formed during the combustion of pine firewood cannot be removed by mechanical methods. They are absorbed into the rough surfaces, literally eaten into the material from which the chimney is made, so even the use of special chemicals is not always effective.

The main feature by which you can determine the presence of dangerous deposits in the furnace is a sharp creosot smell that appears immediately after the start of the furnace and then feels for a long time. By the way, substances that at the same time fall into a heated room belong to the category of carcinogenic. That is, with prolonged inhalation of such air, the danger of the development of cancer tumors in the human body and other hard.to.healing diseases increases.

Thus, the answer to the question of whether it is possible to heat the stove with pine firewood is obvious. It is better to avoid this, and if there is no other option, then it is necessary to at least mix pine logs with firewood from other wood, preferably, oak or birch, as well as add special substances to the furnace, which prevent excessive allocation of soot and deposit of resins on the inner surface of the chimney.

The advantages of pine firewood for the stove

The advantages of pine logs for heating and heating water in the bath and house include:

  • Simplicity of processing. Large logs are easily cut or red.hot into smaller ones, which are conveniently laid in a firewood or fuel. Note that the optimal size of coniferous logs. 5-10 cm shorter than the length of the fuel;
  • pleasant aroma of conifers when heated. Resins, in excess contained in such wood, fill the room with a pleasant and healing aroma. But this type of firewood is suitable for paired. The closed type of furnaces located, for example, in a separate boiler room reduces this advantage to naught;
  • availability. coniferous logs can be purchased at a low price, they are in any specialized store.

Note that a pleasant coniferous aroma can lead to the opposite effect. For allergies, the high concentration of resins in the air (especially, wet) can be dangerous. Therefore, drowning pine wood in the room where people with respiratory diseases are located, the cardiovascular system is necessary with caution.

Disadvantages of using pine logs for the stove

Opponents of the use of coniferous firewood for the furnace give the main argument. Low heat transfer of pine. This means that when burning pine firewood, little heat is released. For example, compared to deciduous wooden rocks. But here it should be noted that the heat production of the tree largely depends on the humidity. Therefore, firewood is recommended to dry well before use. And the amount of heat, which is released during combustion of an equal volume of different varieties of wood, differs slightly.

It is more important to talk about heat production that can be obtained if you drown the stove with pine firewood. We are talking about the temperature obtained when burning a given volume of firewood in a conditional firebox. The standard in this indicator is a mountain maple, whose heat production is 1200 C.

If we consider the most popular types of firewood in our country, which are used to burn in the furnace, pine are at the end of the rating. They give out an indicator, which is 52 % lower than the reference. For example, the same indicator in oak is 70 %. On practice. Pine firewood burn quickly, forming a lot of ash and coals. But heat is obtained many times less than when burning firewood from deciduous rocks.

  • Low security. If you plan to drown the stove with pine wood, pay attention. All coniferous breeds (except larch) are distinguished by a large mol. The latter accumulate in special s between wood fibers. When heated, they burst, and the resin is sprayed around. That is why, pine logs should not be used for burning in fireplaces with an open firebox;
  • High saga formation. Everything is all in the same high resin content. As a result of combustion, resinous soot is formed, which is actually eaten into the walls of the chimney and fuel;
  • High fire hazard. Small soot on the inner walls of the chimney. A dangerous combustion product with a high fire and explosion hazard. The result will be the destruction of not only the furnace, chimney, but also the failure of other heating equipment. Most often, such problems are found in metal and asbestos.cement chimney. If you have to drown with pine wood, the oven is not recommended.

Separately, it is worth saying that the use of coniferous logs over time leads to a deterioration in the operation of a furnace, a solid fuel boiler, a reduction in traction. The guilt of everything is dense soot deposits that are very difficult to remove mechanically. Experts note that the most actively tar and tarry deposits are formed in the case when the firebox operates in smell mode.

The main feature indicating the formation of a strong soot is worn inside the heating system. Creota smell. It looks like the aroma of birch tar and coal, but in the case of the formation of dangerous deposits, a very concentrated and intrusive. Appears immediately after the kindergarten or the start of the boiler and remains for a long time. over, those substances that enter the dwelling are attributed to carcinogenic. The more their concentration, the more dangerous they are for humans.

If you decide to drown the stove with pine wood, periodically burn aspen or alder logs. They will help to remove the already formed soot.

Is it worth drowning the stove with aspen firewood? The answer to this question is not so unambiguous. For woody bath stoves, pine is optimal. Available, therapeutic aroma, rapid combustion. But for heating equipment of intensive constant use, it is better to choose other options. The use of cheap and affordable pine firewood in the long.term result will lead to a strong smoke of the system, a decrease in the efficiency of equipment, traction and the entire heating system. In addition, tarry soot deposits are carcinogenic and can harm human health.

What are alternative options?

In addition to the above.listed wood varieties are popular briquettes from TOA. Their advantage is that they do not need to be injected, dried and in any other way to prepare for burning.

Instead of lump wood, you can use sawdust. But at the same time, firewood is still needed. With their help, kindling is performed, sawdust is added behind it, which should be no more than a third of the total volume of fuel.

Which is better to use to clean the chimney?

Periodically you need to do the prevention of the chimney. Soot and resin deposits are removed from it. There are these reasons for this:

  • The inner lumen is overgrown, which is why the craving worsens and, accordingly, the heat transfer decreases.
  • If the chimney is insufficient, then the effect of reverse traction may occur. Instead of going out to the street, smoke will return to the room, and this is the reason for the poisoning with carbon monoxide.
  • Having reached a critical level, the soot lights up. In fact, there is a microvumber inside the chimney. During the burning, a lot of heat is released and heating occurs up to 1200 ° C. Then the chimney requires major repairs.

To prevent the state of the chimney, among other things, with small sediments Osin or alder firewood tourniques. The stove needs to be thoroughly fetled. In addition to firewood, briquettes that have a special chemical composition are also used. However, provided that large sediments of soot are observed inside the chimney, burning of the resin will not help. Then the mechanical cleaning of the pipes is inevitable.

Author

Laidred

| Denial of responsibility | Contacts |RSS