How to turn off an electric stove Electrolux
Owners of such real estate may experience a separate grounding circuit. It is done like this:
- Behind the outer wall of the structure, iron rods with a diane of 16 mm and a length of 250 cm in an amount of 3 pieces are dug into the ground;
- Damaged rods are connected by a strip of steel 4 cm wide and 0.5 cm wide;
- A ground (yellow-green) wire is removed from the electronic shield, which previously ended with the tip;
- From the grounding circuit up to the grounding wire stretches the wire-roller. Recommended diameter of such wire. 0.8 cm. At the end of the rollery, an iron plate with a hole for the bolt is previously welded. The grounding cable with a bolt is fastened with a launch plate at a height of at least 250 cm from the ground level;
- The grounding cable is connected to a separate zero bus in the shield. A grounding wire from the installed slab is connected to the same tire.
Fundamentally! Before taking the grounding device into operation, it is necessary to invite a specialist to measure the installation resistance. You can perform such verification without the help of others only if you have a special device. The resistance value should not be more than 8 ohms.
The steel is dark | Round for vertical grounding conductors | sixteen | – | – |
The steel is dark | Round for horizontal grounding conductors | ten | – | – |
The steel is dark | Rectangular | – | 100 | 4 |
The steel is dark | Angular | – | 100 | 4 |
The steel is dark | Pipe | 32 | – | 3.5 |
Steel covered with zinc | Round for vertical grounding conductors | 12 | – | – |
Steel covered with zinc | Round for horizontal grounding conductors | ten | – | – |
Steel covered with zinc | Rectangular | – | 75 | 3 |
Steel covered with zinc | Pipe | 25 | – | 2 |
Copper | Round | 12 | – | – |
Copper | Rectangular | – | fifty | 2 |
Copper | Pipe | 20 | – | 2 |
Copper | The rope is multi.wire | 1.8 | fifty | – |
First start
First of all, it is necessary to check the contents of the oven and extract everything superfluous from it.
Next, you need to insert the fork into an electric outlet and set the timer on the required temperature regime. If the oven is used for the first time, then it is recommended to “burn” it. For this, the device is heated at a temperature of 120 ° to 150 ° C empty for 20-30 minutes.
Then you can open the door and let in fresh air. With further use, after heating to the desired temperature, a baking sheet with products is inserted.
Attention! When using the oven, you should remember its strong heating. Touching its elements without protective mittens can lead to serious thermal burn.
How to use the Teka VT TC 2P cooking hob
After the end of the preparation time, the thermostat handle must be installed in position “0” and disable the device from the network. When the oven has cooled, it should be cleaned.
How to enable a glass.ceramic induction stove with sensory control?
Electric slabs for use are divided into two categories:. dependent. Have a connection with the oven through the wires and control mechanisms Independent. “By themselves”, control without an oven or often do not even have it.
First you need to turn on the stove as a whole. a touch start button located on the panel. For individual firewood, there are the same activation zones with power adjustment (as many as 9 modes!). Carefully read the instructions. each manufacturer and model has some features. To turn off the panel, you need to touch the “Stop” button, but induction furnaces have an automatic shutdown, if nothing put on them for a long time.
IMPORTANT! Read the instructions carefully and study the panel. everywhere there are special modes or various designations for the same functions. Only the attached book for the operation of equipment will give you specific information based on the model and company of technology.
Pay attention to the possible functions that are built into your modern glass.ceramic furnace. Now they can defrost food, heat, have a booster, control over electricity consumption, and protection from children. Wonderful option. timer. You can choose a deferred start and dinner will start to warm up automatically while you are going from work.
How to adjust the temperature, correctly use burners
In order to set the correct temperature in the electric stove, it is necessary to carry out simple manipulation:
- Turn on the stove;
- Choose a burner and press on the sensor responsible for it;
- Press the temperature button (usually indicated by symbols.) and set power (usually from 1 to 3 or 1 to 9, depending on the model).
ADVICE! During the first operation, it is best to set the temperature regime to the maximum. Thus, you can evaluate the power of specifically your stove in the future, select the optimum temperature.
How to enable an electric stove? When using an electric stove, it is also worth taking into account the type of fireplace installed specifically on your model. They may be:
- Spiral (usually installed in the earliest models. As a rule, it is located under a special plate). The stove of this type must be carefully monitored. Heating and cooling is much slower. Cooking on such a panel should be carefully.
- Corrugated (in more modern models in the place of spirals began to install a corrugated tape. This system turned out to be much more efficient and safe).
- Halogen (in advanced slabs set fireplaces operating from halogen lamps. The main advantage is undoubtedly rapid heating and cooling, as well as a high level of safety).
ADVICE! To quickly heat the finished dish on the electric stove, just heat the burner to the maximum temperature, put the dishes, and then turn it off. While she cools down, the dish will have time to warm up.
What dishes can be used
Of course, every good housewife in the house has many types of dishes, but not all is suitable for cooking on the hobs of your electric stove.
ATTENTION! In any case, you can use old pots without copper or aluminum coating, as well as cast.iron cauldrons. Such dishes can not only scratch the hobs, but also strongly worsen the work of your stove and even disable it.
For the hob, you can use:
- New enameled pots;
- Stainless steel containers (the bottom should not be corrugated!);
- Black ceramic dishes (usually has a special marking);
- Cast iron containers with a flat bottom.
ATTENTION! The size of the dishes should strictly correspond to the size of the burner! The difference is not more than 1 cm.
How to adjust the temperature, correctly use burners
In order to set the correct temperature in the electric stove, it is necessary to carry out simple manipulation:
- Turn on the stove;
- Choose a burner and press on the sensor responsible for it;
- Press the temperature button (usually indicated by symbols \-) and set power (usually from 1 to 3, or 1 to 9, depending on the model).
ADVICE! During the first operation, it is best to set the temperature regime to the maximum. Thus, you can evaluate the power of specifically your stove in the future, select the optimum temperature.
How to enable an electric stove? When using an electric stove, it is also worth taking into account the type of fireplace installed specifically on your model. They may be:
- Spiral (usually installed in the earliest models. As a rule, it is located under a special plate). The stove of this type must be carefully monitored. Heating and cooling is much slower. Cooking on such a panel should be carefully.
- Corrugated (in more modern models in the place of spirals began to install a corrugated tape. This system turned out to be much more efficient and safe).
- Halogen (in advanced slabs set fireplaces operating from halogen lamps. The main advantage is undoubtedly rapid heating and cooling, as well as a high level of safety).
ADVICE! To quickly heat the finished dish on the electric stove, just heat the burner to the maximum temperature, put the dishes, and then turn it off. While she cools down, the dish will have time to warm up.
How to use an induction stove correctly
In order for the stove to work for a long time and without any problems from the user, only one thing is required. to comply with the requirements given in the operating manual. This document describes the procedure for choosing the location of the model, the procedure for its inclusion and operation.
How to connect a stove
The main tool that is required to connect the device to the network is a screwdriver. Directly for connection, you will need to purchase a certain amount. Most often use a cable with a cross section of 4 to 6 kV. mm. The length of this cable should be enough to connect the panel. As a rule, a 4-living cable includes a set of delivery. 2 veins, brown and black-these are phases, in blue lived-“0”, and yellow-green wire-Earth. The ends of the wires must be cleaned. On the back of the product is a comb in which the cleaned wires are installed. The free end must be connected to the house electric network.
How to enable an induction stove
So, the panel is included in the network. After the end of this process, some models signal that everything proceeds in the standard mode, and the panel can be turned on.
On the control panel, as a rule, there is a “start/stop” button, pressing on which will lead to the inclusion of the device.
Before starting work, it makes sense to clear the surface of the residues of the packaging and traces of adhesive substances that could remain after production. By the way, in the first minutes of operation, it can seize burned rubber. But you should not be particularly worried, this unpleasant spirit will soon leave.
Electrolux Induction Range with WaveTouch Controls
For each individual zone, separate buttons are provided on the control panel, in addition, some models provide separate regulators. The power is set from 0 to 9.
The operating instructions described in detail which power modes are optimal for boiling, and which for heating or direct cooking.
How to turn off the induction panel correctly
After cooking, you need to turn off the panel. To do this, you can press the Start/Stop button or wait for a certain time, after which the panel itself will go into waiting mode.

Safety precautions
For an electric stove to work for a long time and without complaints, it is important to use it correctly. The basic safety regulations are as follows:
- Check the dishes before cooking. Its bottom should be clean, even and preferably dry.
- Before putting the dishes on the burner, make sure that on the surface of the burner itself there are no traces of burnt food, dust, or a stove cleaning tool.
How to unlock the Candy hob
To remove the blocking from the Kandy hob, click on the “Castle” button (you need to press for several seconds).
To cancel the lock, click on the “Castle” button on the control panel (within 3 seconds).
Thus, having an idea of how to unlock the hob, you can easily cook your favorite dishes and not be afraid that children can turn on the stove and burn yourself. We described other cases when you may need to remove the lock. Now you know how to unlock the Bosch hob, as well as panels of other manufacturers, such as NEFF. Gorenje, Hotpoint Ariston, Hansa, Weissgauff, Samsung, Kuppersberg, Lex and T.D.