Home Small appliances How to replace the hob that is sealing
Small appliances

How to replace the hob that is sealing

How to replace the hob that is sealing

How to correctly install the latest hob, so as not to destroy the headset? Focus on its size from the annotation. If the brochure is lost, the subsequent technique is used:

  • Turn the product on the table;
  • Measure the width and length along the inner edges;
  • Measure the characteristics of the protrusion for fixation and draw it with a pencil on the surface;
  • Note these characteristics on the table with a pencil;
  • Find the center of segments and make markings;
  • Rightly check the gaps. For a protrusion of 15 mm long, enough to leave 10 mm. For installation of cooking itself, you need a compensation of 5 mm.

Specialists advise in stages and alternately to make calculations:

  • Marking of the cabinet based on the size from the annotation by drawing a rectangle;
  • Determination of the center. using roulette. It is necessary to draw a cross on the table so that one fishing line for a trimmer correlated with the front edge of the countertop, and the 2nd was perpendicular to it;
  • Maslar tape is glued on black table surfaces and markings are already made on it;
  • Removal of measurements of the panel itself with a supplies by 1-2 mm;
  • Drawing lines. there should be 4 of them.

At the final step of the markings, the evenness of the figure is checked by a ruler or level.

Advice! If you doubt the correctness of measurements, make a cardboard layout and use it.

We make measurements

How to correctly install the latest hob, so as not to damage the headset? Focus on its size from the instructions. If the brochure is lost, the following technique is used:

  • Turn the product on the table;
  • Measure the width and length along the inner edges;
  • Measure the options for fixing and draw it with a pencil on the surface;
  • Note these parameters on the table with a pencil;
  • Find the center of segments and make markings;
  • Carefully check the gaps. For a protrusion of 15 mm long, it is enough to retreat 10 mm. For installation of cooking itself, you need a compensation of 5 mm.

Experts recommend in stages and consistently to make calculations:

  • Marking of the cabinet based on sizes from the instructions by drawing a rectangle;
  • Determination of the center. using roulette. You need to draw a cross on the table so that one fishing line for a trimmer corresponds to the front edge of the countertop, and the second was perpendicular to it;
  • Malar tape is glued on dark table surfaces and markings are already made on it;
  • Removal of measurements of the panel itself with a margin of 1-2 mm;
  • Drawing lines. there should be 4 of them.

At the last stage of the markings, the evenness of the figure is checked by a ruler or level.

Advice! If you doubt the correctness of measurements, make a cardboard layout and use it.

Peculiarities

The specifics of installing the hob in the countertop largely depends on whether it will be electric or gas. Electric, as you can guess, should be located near the power point. Be sure to take into account both the cable section and the power of the nearest outlet. You cannot also ignore such a procedure as grounding metal parts. The installation of a gas surface is a little more difficult, since it is important to think over how to dock it with a gas pipe.

Stove & Fireplace Glass Gasket Seal Replacement

In addition, safety requirements categorically prohibit independent connection of gas hobs. To conduct this operation, it is necessary to invite a special services employee, who will fully fulfill everything. Of course, you can try to install everything yourself, but in this case you will have to expect not only serious sanctions, but also the emergence of a real danger to the lives of the inhabitants of the whole house. By the way, sanctions can reach the full overlap of gas and sealed the valve.

Install and connect an electric stove on your own, is certainly allowed, but clearly following the existing instructions. In the case when a person does not have any skills in working with electrical devices, he is recommended to contact specialists. If the installation process is carried out incorrectly, then negative consequences can include not only the impaired operation of the device, but also its breakdown or even failure of the entire wiring in the apartment.

There are several more nuances regarding the connection of the hob. For example, the maximum possible gap between the panel and the countertop is 1-2 millimeters. The thickness of the countertop itself should correspond to the minimum figure specified in the instructions. In addition, the location of the countertop is always leveled depending on the front edge of the part of the kitchen set.

What is a sealing tape

Mostly make a hole, which is more than 1 cm. Both in length and width. But due to the fact that the size of the hole is large, the hob “rides”. To get rid of this, the sealing tape is glued to it and attached to the countertop.

This installation method has established itself well. It provides the opportunity to thoroughly fix the device. So that moisture falling under the panel is excluded.

Typically, the manufacturer attaches a seal for glass.ceramic hobs to the device. Когда ленты в комплекте нет, тогда применяют обычный уплотнитель для дверей или окон из поролона. It is necessary to choose a thin tape. Then the gap between the panel and the countertop will be minimal.

IMPORTANT! We pay attention to the fact that experts do not advise applying something else instead of the sealing. For example, bilateral tape, glue. Of course, they can glue the hob to the countertop. However, then, when it will be necessary to dismantle the device, big problems await you. Serious breakdowns cannot be avoided.

What experts advise when connecting hobs?

Hobs of modern manufacturers are a functionally completed equipment that can be used independently. But in many headsets there are special niches for building a stove. The correct installation of a new hob in a ready.made countertop will ensure the quality of its connection and functionality.

Features of products

For the hob, the sealant in the countertop is also necessary for a tight fixation of this kitchen technique. It is used at the installation stage. A self.adhesive tape is fixed on the surface of the panel immediately before placement in the countertop. It is fixed with one piece, not required to cut into parts. If after fixing there are surpluses of protruding rubber, then they are easily removed with a knife.

replace, sealing

It is periodically required to buy a h at the hob, as it deteriorates during operation. This is due to a violation of the temperature regime and the effects of aggressive substances or due to inaccurate use of kitchen equipment.

Seals for electric and gas hobs have the same features:

The reasons for the failure of regular seals

During cooking on the stove, its components are subjected to temperature changes. Fat, dirt fall on the surface, which are subsequently washed off with aggressive detergents. This negatively affects the service life of rubber components. The installation of new sealing elements is needed if the following negative phenomena are observed:

Sometimes seals for installing the hob are out of order due to natural wear. If the rubber components of the electric, gas stove, the oven are stretched, deformed, you need to replace them.

When choosing a sealant for the installation of the hob, the surface parameters are taken into account, on which the sealing components will be fixed. Materials are resistant to fever, differ in water.repellent qualities. This is a durable, durable rubber mixture that performs the function of isolation.

How to choose a hobal bar?

At home, a hobal seal has become unusable? No need to be upset and hurry to the technique of equipment behind a new device. After all, today you can easily purchase any spare part for a particular equipment. The company “ZIP-REM” offers a wide range of components for slabs of various models and manufacturers. Our catalog presents only high.quality and reliable spare parts for household appliances.

Reliable sealing tape for the hob with proper operation can last a long time. However, it should be made of suitable material, be dense and durable. When choosing a gasket, the following factors must be taken into account:

  • Production material. The product should be made of reliable and wear.resistant raw materials. It should keep high temperatures well and maintain its basic properties for a long time.
  • Manufacturer. Each company has its own quality standards and uses certain materials. We recommend that you prefer only well.known and trusted manufacturers with certified products.
  • Value for money. The better you choose the seal for the hob, the more expensive it will cost. But at the same time, the laying will last you much longer than a cheaper option.

The effectiveness and performance of the hob directly depends on the quality of the seal. With its malfunction, the use of the plate is not always possible and safe. This element may become unusable at any time. In this case, it is urgent to replace it with a new.

The Zip-RM online store presents a large selection of components for kitchen household appliances. You can easily find a suitable heat.resistant ribbon for the hob in our catalog. Our products are used to compact a variety of compounds. The presented product has high heat resistance, can operate at high temperatures and for a long time. Each element has different sizes and cross.section, so you easily pick up the seal for its stove. Our products allows you to achieve maximum sealing, it is elastic and retains its form even with prolonged operation.

How to hide (ennoble) the gap between the gas stove and the countertop (the gap is not large)?

You need to come up with something about hid the gap between the gas stove and the countertop, or somehow ennoble this adjoining.

Immediately I want to deceive a number of important points:

If you have wooden furniture in the kitchen, then not every gas stove can be installed close to such furniture.

But there are modern gas stoves with very high.quality thermal insulation (the side walls do not heat up at all) where the installation is acceptable.

If this is not your case, then you need a kind of “laying” of non.combustible material between the stove and furniture.

Further, the countertop can be higher than the gas stove (less often below), in this case, ennoble the very gap is a little more difficult.

If the gas stove is at the same level of hundreds of a countertop, then you can hide the very gap like this

The profile can be stiff, soft, the material of manufacture is also different, in the case of a gas stove it is better to use a metal profile, you can make stainless steel, or an aluminum T-shaped profile.

The plate should be periodically pushed away from the wall and washed the wall behind the stove, so it is better to fix the profile only to the countertop, or not fix it with a mechanical and adhesive method, but simply insert tightly into this gap.

If you just need to ennoble the adjacency, and not completely hide the gap between the stove and the countertop, then from the end of the countertop you can install such

In my opinion, this option is optimal, taking into account the fact that the gas plate is periodically pushed back (connected to gas on a flexible gas bar, that is, it is mobile).

Sealing built.in kitchen technology

The kitchen technique, with which we conduct heat treatment of food, is often exposed to negative effects that water and other liquid products have on it. After all, this always leads to the fact that the technique spoils and prematurely exhausts its resource, fails. It is clear that any preventive measures can give the desired effect.

In order to prevent the destruction of the slab, oven, hobs, there must be sealed joints. And inside the design. for example, when fastening glass in the oven. And outside. for example, at the joints with furniture, which adjacent to the equipment.

If you manage to correctly install a built.in hob, then you can be sure that the equipment will work without interruptions. And caring for a panel will be just.

Why Has My Ceramic Hob Cracked, And How Can It Be Repaired? | AEG

The installation process of the hob

It is necessary to cut a hole in the countertop. It is from this that the process of installing the hobs begins. The optimal dimensions can be found by reading the instructions that is always attached to the device when buying.

replace, sealing

When you make holes, immediately proceed in aligning the edges. Then the grinding process awaits you. For him you will need to prepare sandpaper in advance. You can also use a file.

In the case when the countertop is made of a laminated plate, you have to additionally process the edges of the rectangle. What is the essence? Such plates are based on laminated wood-bearing plate or wood-fiber slab. And these materials are very susceptible to moisture. Therefore, one cannot allow them to get wet. To do this, treat the ends of the sections with glue. Will fit for this and nitrolak. Remember that they should dry.

We pay attention to the fact that when the plate is gas, the hose with the united nut must be connected before the panel is installed in the countertop. If you immediately install the surface, then there will be problems with the gas supply. It will be more difficult to do it.

What is a sealing tape

When you cut holes for the hob, it is difficult to ensure that it perfectly coincides with the size of the device. Typically, in the operating instructions, the manufacturer gives the desired sizes of the landing hole. But not only. There he also indicates what the maximum error should be.

Mostly make a hole, which is more than 1 cm. Both in length and width. But due to the fact that the size of the hole is large, the hob “rides”. To get rid of this, the sealing tape is glued to it and attached to the countertop.

This installation method has established itself well. It provides the opportunity to thoroughly fix the device. So that moisture falling under the panel is excluded.

Typically, the manufacturer attaches a seal for glass.ceramic hobs to the device. Когда ленты в комплекте нет, тогда применяют обычный уплотнитель для дверей или окон из поролона. It is necessary to choose a thin tape. Then the gap between the panel and the countertop will be minimal.

Sealing process and proper sealing

When you prepare a landing hole in the countertop, you can install the panel.

The sealing tape is attached to the stove before placing it in the countertop. Usually the seal that the manufacturer attaches to the device is a self.adhesive tape. This is a strip of material that is covered with glue and protected by a film.

After extracting the hob from the packaging, it is turned over and the seal begins to fix it. The protective film from the tape must be removed gradually, as it joins with the surface. Then you will not get confused in it.

We pay attention to the fact that the sealing tape must be attached to the panel with one piece. It is not necessary to cut it into parts. The ends should be tight. There should not be spaces. Then we can talk about reliable sealing, which will remain for a long time.

As soon as the seal is glued, insert the hob into the hole and attach to the countertop from the bottom. Fasteners, that is, a set of self-tapping screws and records, always complete with the device.

Sealants for hobs and ovens

Gas slabs and electric plates are increasingly changing to built.in hobs. They have all the same functions. However, they require less space. And they can also fit well into the kitchen set.

So that the device serves for a long time, and there are no many difficulties with leaving, you need to correctly install it.

A sealing ribbon for the installation of the hob can be securely fixed to the device on the countertop. In this case, the risk of moisture enters the ends of the landing hole will be minimized. But there is a very simple technological method to achieve the tightness of the compounds. It is to use special sealants for ovens.

Not every material is suitable for kitchen appliances. There are materials that cannot withstand high temperatures. Therefore, they dry out, covered with cracks, crumble.

replace, sealing

Characteristics of sealants for ovens

Sealants for ovens and other kitchen thermal devices should:

replace, sealing

These high requirements meet the current silicone sealants. For example, Dowsil Q3-1566, Makroflex TA145, FOME FLEX Thermo, Lectite 5399, etc.

Part of these materials (say, dowsil Q3-1566) is used to seal compounds not only in home furnaces, in gas and electric stoves, hob panels, ovens, but even in heating equipment at industrial enterprises. Thereby they prove their high efficiency.

Pasty consistency of special heat.resistant sealants for ovens and hobs do not allow them to drain when you apply them. They have high adhesion to many materials. They are able to maintain stability and elasticity at a wide variety of temperatures. Sealants, when they are hardened in normal conditions, become a strong substance resembling rubber. And he has high operational characteristics.

Author

Kerariel

| Denial of responsibility | Contacts |RSS