Home Electric stoves / gas stoves How to remove the top cover of the gas stove ardo
Electric stoves / gas stoves

How to remove the top cover of the gas stove ardo

Independent repair of gas stove

It is impossible to imagine any kitchen without a cooking surface, whether it is an electric or gas stove, as it is on these units that the cooking process takes place. But unfortunately, these devices fail over time for a variety of reasons. To make repairs of gas stoves, to eliminate breakdowns of various kinds and conduct maintenance should be a qualified specialist of the gas service. But there are minor malfunctions, in which you can repair the gas stove by yourself.

The gas stove is a fairly complex device. In modern models, hardware is used to control operating parameters. There is an auto ignition and other useful options. In the course of operation, the stove gets dirty. Food remains and grease evaporate on the important structural elements of the device. Different brands of gas stoves have certain types of faults. If abnormal behavior of the device corresponds to one of them, the user can easily understand what to pay attention to and, if necessary, make a simple repair.

Hansa

The following typical malfunctions are encountered in gas stoves of the brand Hansa.

  • The burner flame disappears immediately after the user releases the gas regulator knob. There could be several reasons for this. The consequences of contamination include nozzles clogged with food and grease residue. From the sector of hardware problems can be noted failure of the thermocouple, breakdown of the solenoid valve, malfunctions in the electrical ignition system.
  • The burner doesn’t burn evenly, the flames don’t match along the contour. The cause may be trivial dirt caught in the hole of the nozzle. There are also more serious breakdowns. Typical, amenable to uncomplicated repair. skewness of the air inlet flap.
  • No spark, gas does not ignite. This can indicate both contamination of the spark plug contact and wear and tear of this element. Also, the stove does not ignite due to malfunction in the gas control sensors.
  • Oven door does not fit tightly. It happens because of its deformation. Or shows that the axle mounting point is displaced or bent.
  • Gas valve cannot be turned. This mishap is caused by physical damage to the shut-off valve. Oil may have dried out in the tap or the handle retainer may have come loose from the axle rod.
  • Smells like gas. If this happens, it is worth immediately checking all the joints of the supply hose with a soapy solution. The faucet is also inspected. Examine the hose itself for damage.

Simple test for gas leaks with soapy foam

Darina

The following malfunctions occur in the Ardo stoves of this brand:

  • Spontaneous actuation of the electric ignition due to contamination of contact groups;
  • The flame burns constantly;
  • control knobs due to the accumulation of dirt jam or do not change the gas supply;
  • Gas continues to flow after the flame goes out due to a malfunction of the combustion control;
  • The operation of the air supply system malfunctions, smoke and gas smell, the burners’ light turns orange.

Even with famous brands, breakdowns happen. Ardo stoves have the following problems.

  • Combustion and ignition control failure due to spark plug, flame sensor, thermocouple failure. In this case the burners may shut off or not ignite spontaneously.
  • If the burner shuts down spontaneously, it could be a buildup of dirt. It occurs in the nozzle area and on the surface of the spark plug electrode.
  • The knobs are difficult to turn, indicating that they need to be thoroughly cleaned of dirt and grease residues.
  • The ignition switch does not work or does not always work. In this case it is necessary to check that not only the surface of the spark plug electrode is clean, but also the contact groups of the button. It is worth checking the continuity of the wires leading to the pulse unit, as well as the voltage of the power supply.
  • Flame that turns orange and is not intense enough points to a contaminated nozzle. It should be thoroughly cleaned, making sure that the gas outlet opening is clear.
  • If you smell gas, call a qualified service technician. Thus take the usual precautions in the form of overlapping the supply and thorough ventilation of the room.

Ariston

The following breakdowns and malfunctions occur in Ariston ovens.

  • The burners do not ignite. It is necessary to check the gas supply, the ignition system operation.
  • Faults in the electronic control system manifest themselves in many different ways and require expert repair.
  • No ignition of burner. The most common cause is a faulty solenoid valve.
  • The flame of the burner is uneven, indicating that the nozzle is dirty.
  • Accumulated dirt can cause irregularities in the ignition system, spark ignition assembly, irregular gas supply due to burner ducts blockage.

Gefest

The following breakdowns can be found in popular Gefest stoves.

  • Uneven flame of burner. Need to clean nozzles, ducts, adjust gas flow.
  • Burner fails to ignite spontaneously. This indicates breakage of the flame control thermocouple.
  • The flame does not appear due to a breakdown of the electric ignition, a malfunction in the control system. There is also a trivial reason, concluded in the lack of gas supply due to a broken faucet.
  • Unexpected display signals, lights on or on the contrary, not working, temperature control failures. all this indicates a failure of the electronics and requires a qualified repair.

Repair with your own hands

You can repair your gas stove with your own hands when the following malfunctions occur:

The burners don’t light

This malfunction can be caused by a number of reasons:

  • clogged gas nozzle;
  • Failure of the ignition plug;
  • damage to the insulation of the spark plug wire;
  • Faulty ignition control box;
  • Power button malfunction.

Nozzle clogging

The nozzle (nozzle) of the appliance may be clogged by foodstuffs, detergents or products of gas combustion. Self-repair of gas stove in this case is very simple: it is necessary to remove burners and clean the nozzle with a wooden toothpick (do not use for cleaning metal objects, such as paper clip or needle).

If you can not clean the nozzle without disassembling the stove, you should remove the top panel of your device, unscrewing a few screws. For a good cleaning of the nozzle, it can be unscrewed.

Electric ignition does not ignite the gas

Before you disassemble the gas stove, you should disconnect from it the power supply (voltage for the candle. 220V), which is required for the ignition electrode. This malfunction of the appliance with an electric ignition can affect either one burner or all at once. If the spark does not jump on one burner, it means that the spark plug (electrode) has failed. On it, in the ceramic insulator, there may be a crack, as a result of which the electrode ceases to work properly.

To make the repair of the gas stove with your own hands about replacing the spark plug, it is enough to remove the burners, open the stove lid (unscrewing a few screws), and change the electrode for a new one.

Also, a frequent malfunction of the ignition on one burner can be a damaged wire, going to the candle. To check this, you need to press the ignition button with the lid open. If the wire in any place is “broken”, then you will see a spark in this place, either on the body of the appliance, or on the foil, which is covered with the oven. Repair of the electric ignition of a gas stove with a damaged wire is to replace it with a new one, or it must be moved to another place so that there is no “breakdown” on the ground.

In the case when the electric ignition does not work on all burners, including the oven. it means that the ignition unit is out of order. To repair the ignition unit requires replacement of the block with a new one after removing the upper panel of the device.

The process of repairing the electric ignition of the gas stove Darin is shown in detail on this

The fire goes out after ignition

There are times when a properly working gas stove suddenly begins to give surprises. For example, you turn on the gas, it lights up, and when you release the knob, it immediately goes out. These symptoms indicate a malfunction of the thermocouple, the sensor that turns on the combustible mix.

Thermocouple works in the following way: when heated it generates an electric current, which magnetizes the electromagnetic valve. The valve, in its turn, opens and the gas flows freely into the burner. If the thermocouple stops heating, the electrical impulse is lost and the valve shuts off the supply. Thus, if after opening the tap to turn on the gas and ignite it with an electric candle, combustion immediately stops. this means that the solenoid valve is triggered and cut off the supply of combustible mixture.

To repair a gas stove in case of such a malfunction is simple enough.

  • First you need to remove all the handles and the top panel of the stove, unscrewing the screws on the sides of the cover and under the burners (designs of stoves may be different, respectively, and the location of fasteners may differ).
  • After unscrewing the fasteners, remove the top cover of the unit.
  • After disassembling the unit near the failed burner, you will see two protruding parts. The white one is the spark plug, and next to it is a thermocouple.
  • The wire from the thermocouple goes to the connector, from which you must remove it. Disconnect the gas sensor from the burner.
  • After removing the non-working element, install a new one, bought in advance.

This is how you can repair a gas stove Gefest, Ardo, Brest stove and Hansa when the thermocouple fails.

Also do not forget about safety: before you repair a gas stove, you should disconnect it from the mains.

Button malfunction

Sometimes the ignition spark plug failure can be caused by a failed button. This malfunction when repairing gas stoves Gorenje or other brands can be determined by throwing the wires (having previously removed the upper panel of the appliance) to another button of the gas stove. If the ignition when you open the burner tap works, it is necessary to replace the faulty button.

The oven door will not close

The most frequent breakdown of the oven is a bad closing of the door of the oven. It occurs most often when there is a small child in the house, which simply sits on the open door, as a result of which the brackets that hold this part, bent and do not perform their function of pressing the leaf.

To repair the oven of the Indesit gas stove, Brest 1457 or Flama stove, you will need to disconnect the door from the unit. To do this, you need to:

  • Since the door is held on hinges equipped with latches, you need to bend them on both sides of the unit.
  • After that, you need to carefully close the door until it stops at the latches.
  • Next, you need to pull the door slightly towards yourself and upward, after which it will easily detach from the stove.
  • To get to the brackets, making repairs of the gas stove Gorenje or when repairing the gas stove Darin, as well as the Brest unit, you need to remove the side walls of the oven. After removing the sides, you will see the brackets, which are responsible for clamping.
  • The brackets should be removed from the gas stove oven and visually determine where they are deformed. Using a hammer and pliers, you can try to straighten the deformed places. But in the case when this part is broken, it must be replaced with a new one. Stores sell different kinds of parts to repair the oven and stove. Match the brackets to your gas stove model.

Interior of the stove

Before you do the repair, you need to understand what a gas stove is, what parts are present in it, and what repair of a gas stove with your own hands may be required in this or that case.

There are many companies that produce gas stoves: Gorenje, Ardo, Ariston, etc.д. But all stoves, even if they differ in price, have a similar type of internal device.

The structure of burners

The most visible part of any stove is the burners. Each burner is bolted to the stove table. The burner also has several parts: they have a cover, flame-spreader and injector.

Each burner has a steel and copper tube connected to it via a socket similar to an American-style socket. Thanks to this device, the burner receives gas.

No special tools are needed to work on the burners: you will need a wrench, most likely a 13 wrench, to disassemble the burner parts if it needs repair or cleaning.

After completing the repair and assembly it is necessary to assemble the structure and check how tight it is to prevent gas leakage.

Each burner has two candles around its circumference.

One helps to create the ignition, working by means of piezo elements or electronic circuits, and the second one serves as a thermocouple connected to the circuit that controls the combustion.

Candles differ from each other even in appearance, so it will be difficult to mix them up.

Candle under the electric ignition has a ceramic caftan, it is necessary to prevent the spark from penetrating below the required level.

That is why it is important to properly ground stoves with integrated electric ignition. Also, electric ignition does not tolerate the use of water pipes and metal threads.

It is important to separate the hob from the riser with special gaskets during installation and repair, otherwise there is a real risk of explosion.

How quickly the semiconductors cool down after the flame goes out depends on the reliability and speed of turning on the protection, shutting off the gas, after you have finished using the stove.

Control of gas current

Under the table of the stove you can see the manifold. It has the form of a thick tube, from which the leads to the burners diverge.

Gas current is controlled by solenoid valves, the number of which is equal to the number of burners on the stove.

This is necessary so that if the flame of one burner goes out, the others will still be able to function.

Solenoid valves are equipped with an inductance coil. When the thermocouple heats up, an EMF is generated, which locks the device open.

Self-repair stove

Full repair of gas stoves Gefest, Gorenje and other models requires the intervention of specialists, t.к. Independently make it not only difficult, but also dangerous.

However, there are a number of works that are quite possible with your own hands at home, and bring the stove into working order, if its damage is not too serious.

What to do if the ignition switch is out of order??

The most common problem of gas stoves is the failure of the electric ignition. In the elimination of this problem will help you video. watch it before you start the repair to make everything right.

First of all, you need to disconnect the stove from the power supply, remove the partition and inspect it for deformities.

If you see that there are chips and cracks on it, it means that this is why the stove does not work, and the partition should be replaced.

It can only be replaced when the ignition or auto-ignition is off. do not forget this. After replacing it, check how well it works now.

If your Gorenje or other model has a piezo igniter, the operating procedure will be slightly different.

First you need to remove the device from the control, then remove the stove partition, which is located at the bottom, and remove the igniter, which is screwed to the bracket with a mount.

If it is cracked or otherwise deformed, it should be replaced with a new one. To put a new igniter, you must disable the module responsible for ignition.

Find it will help you find it in the manual of the stove.

After that, you must replace the old part with a new igniter and check how well the gas stove works now.

Oven door repair

Often after prolonged use the doors of the oven begin to stick or close poorly.

To make a similar repair of gas stoves Indesit, Gorenje and others, you need to unscrew the screws that hold the doors and swing them in different directions, so that the door is firmly fixed on the hinges, from which, perhaps, came off.

After that, retighten the screws, if everything is done correctly, the door should fall into place and the oven should close tightly.

If the part still does not work, then you may need to replace the gasket, which is responsible for the tight fit of the oven door to the frame of the stove.

To do this, you need to unscrew the door hinges, which are located above the handles, and remove the lid of the stove.

It will probably also be necessary to remove the interior screws and panel edges, or, you can just push them away and remove the cover that way.

The screws that fix the glass to the panel unit must be removed, and then remove the glass itself, disconnecting the gaskets that hold it in place.

Now you need to disconnect the gaskets themselves, which are between the door and the glass from the inside.

Now you need to replace the gasket with a new one and put all the parts back in place, acting in reverse order.

Use the manufacturer’s instructions, t.к. The device of different models will be slightly different, and you will have to act differently.

Adjusting the gas supply to the burner

It often happens that the gas supply to the burner is not properly adjusted. As a result, the flame burns intermittently or disappears at all. If the device is working properly, the flame should be even and have a bright blue color.

If your device works in a different way, it means that the ignition or auto-ignition must be properly adjusted and the stove.

To do this, you must first turn off the gas supply and then remove the baffle. Then turn it on again and determine which air damper needs adjusting.

To adjust the operation, you need to unscrew the set screw that locks the plate. it is responsible for the proportion in which the gas mixes with the air.

With it in position, turn on the stove and check how it works.

How to disassemble the gas stove

First of all, shut off the gas and disconnect the power supply. Next, following the step-by-step instructions, go step-by-step through the disassembly and reassembly of the gas stove and gas appliance.

Remove all the screws that hold the panels and remove the control knobs. The knobs are on the control panel; you can pull them out with a little effort.

Some regulators may have screws in the regulator base (inside); unscrew these screws with a screwdriver or hex wrench and then remove the control knobs themselves.

Remove the rear panel that covers access to the dashboard.

Supporting and removing a series of screws all around the back panel.

To remove the front panel, remove the control knobs and remove the series of mounting screws that hold the decorative panel attached to the frame.

These screws can be concealed by decorative overlays, molding, or shearing. Separate the trim or trim with a screwdriver or by removing a few screws. How to repair an electric cooktop.

How to disassemble a gas stove

To gain access to the gas burners, remove the grates covering the burners at the top of the stove.

The entire top should either be lifted up and disconnected from the base or possibly open and remain on the hinges.

The oven door, can be removed by pulling it straight up from the rods on either side of the door.

Some hinges have a latch that must be unlocked before the door can be removed.

If there is a blown bulb, remove the mounting screws in the panel as necessary to gain access to the bulb.

Replace the burned out bulb with a new one of the same type and wattage, Then the panel covering the bulb and protecting it from damage can be put in place.

If there is a case of burning out the light bulb in the oven, unscrew the cap and remove it from the oven. Replace the burned out bulb with a new one of the same power, install the bulb in the reverse order of disassembly.

Troubleshooting

Although there is a ban on unauthorized access to the operation of gas appliances, self-repair is possible to prevent more serious problems.

Having taken precautions. opening the windows, getting rid of open sources of fire, preparing a flashlight instead of electric light sources. begin troubleshooting.

Read more about how to repair electric stoves of different models with your own hands here.

Electric ignition

Electric ignition modules are installed in almost all modern models of gas stoves. It is a high-voltage generator supplied to the ceramic electrodes attached to the burners, usually located under the top cover. It appears on one burner or appears intermittently on several burners.

    Most often the essence of the repair is to eliminate the short circuit that has occurred between the body of the stove and the high-voltage cable. Behind the front panel is a technological space used to house the wires and gas pipes. Over time, water and cooking residue build up in the cavity.

It is a liquid substance with an acid reaction, which conducts electricity and provokes ignition failure if it gets between the body and the cable. Wires are cleaned, dried, placed in polyvinylchloride tubes, fastened on plastic stands, making sure that there is no contact with the metal housing.

Thermocouple

Thermocouple. sensor responsible for gas supply. It is a small pointed pin of metal near the burner. Failure of the element is manifested by the fact that immediately after ignition the fire goes out.

To fix the problem, carry out the following steps:

  • Use sandpaper to remove grease, dust, and chemical residue from the element.
  • If cleaning is unsuccessful, the thermocouple must be replaced. To do this, remove the top panel by first removing the handles and unscrewing the bolts.
  • The thermocouple is located near the glow plug. Disconnect from the burner, remove the wire.
  • The place of attachment is cleaned, a new element is installed.
  • Put the lid back on.

Valves

If the gas burner valves don’t turn or turn with difficulty, the reason is a sticking of grease or excess grease or breakage of the steering mechanism.

  • Required to remove the knobs, clean them from grease and lubricant residue. This should be done in a soapy solution, then thermostats should be dried and a thin layer of new grease should be applied.
  • If the problem still exists, after removing the handles, inspect the seating of the valves.
  • If the metal plate located at the valve stem inlet is damaged, it will be replaced with a new one. You can make it with your own hands, cutting from a canning lid or canning jar.

Oven doors

The oven door won’t close for two reasons:

To fix a loose door, unscrew the screws that hold it to the oven, but not all the way. Then wiggle the door in different directions until it is back on the hinges, and tighten the screws as far as they will go. If the problem is not solved, it is likely that the brackets are deformed.

To fix it perform the following:

  • The hinges, complete with locks, located on both sides of the oven, unbend;
  • then carefully close the door until it rests against the latches;
  • Pulling it upward and outward, disconnect the door from the cabinet;
  • then remove the sides of the enclosure to gain access to the brackets responsible for clamping;
  • Parts that require repair, disconnect from the oven, with pliers hammer level the deformed elements;
  • If the bracket is broken, replace it with a new one;
  • Assemble the body, install the door in the reverse order.

Remove the gasket by first unscrewing the door. The chute, designed to install the gasket, is washed with detergent, install a new rubber band and put the door in place.

On how to fix the oven door itself at the stove, read in a separate article.

Cooking hob

If the hob of the gas stove does not work, carry out the following steps:

  • Examine the electric ignition. The problem. in the accumulation of grease, food residues on the element. To eliminate the flaw, it’s enough to wash the part well, dry it and put it back in place. Check also the functionality of the electrical system.
  • Check that the gas flows into the burner. If the gas valve is open and the gas flows into the system, proceed to inspect the nozzles.
  • Perform cleaning of the flutes, which are also prone to clogging with food residues. After rinsing, you must dry the parts thoroughly so that the ignition system will work correctly.

Grids

Over time they burn out and fail. Steel enameled serves for a long time, but due to the peculiarities of the material the appearance quickly deteriorates. Cast-iron serves not so long, because due to the impact of high temperatures it becomes brittle.

Regardless of the material, you can replace the grid yourself. Purchase the part in a specialized store for the correct choice of the model.

Modern gas stoves are equipped with sensors that detect the cause of failure and display information in the form of numbers, numbers on the display. It is enough to take the instruction manual, in which there is a deciphering of error codes, find out the cause of the problem and eliminate it.

The cost of work by specialists

Malfunctions occur suddenly and require rapid repair, especially when the gas stove is broken. However, not all owners of household appliances have the necessary skills. When it is impossible to perform the repair yourself, you have to call a master at home. What costs await the owner:

  • Replacement or repair of the gas valve. 300 to 1,200 ;
  • nozzle cleaning. from 400 ;
  • replacement of the lamp in the oven. from 400 ;
  • Gas adjustment. 500 to 900 ;
  • Lubrication and cleaning of the stems on the supply lever. 900 ;
  • rods replacement. 1200 ;
  • thermocouple replacement. 900 ;
  • replacement of the ignition block. 900 ;
  • cleaning of inlet contacts. 900 to 1 100 ;
  • Replacement of the sealing rubber. from 500 ;
  • spark plug replacement or repair. 800

depend on the stove model and the region where the service and repair of household appliances is carried out.

Overview of frequent faults

If you do not carry out a systematic cleaning of the device, there is a high probability of the following problems:

  • Difficulty in turning the knob. In this situation, remember one rule: the use of force will only damage the knob. This problem occurs if you get a foreign object in the slot between the casing and the plug or if a lot of dirt accumulates. Eliminate the problem by disassembling and cleaning the handle of the gas stove.
  • Gas is not flowing properly into the burner. Even if the knob is turned to maximum, there is a weak flame at the outlet. The probable cause is clogged nozzle holes with food waste or combustion products. You can solve the problem yourself. A toothpick should be used for cleaning. It is also necessary to unscrew the nozzle and wash it with a soapy solution. In no case do not use metal objects, as even a small scratch can provoke a gas leak. But to replace the nozzle it is better to call a specialist.
  • A little tightness in the water tap. This problem occurs when the graphite grease on the stopcock is worn out, the rotary spindle is dirty. To eliminate the problem it is necessary to perform a full flushing of the stove tap. For this operation it is better to call a master, because it will be necessary to disassemble the front part of the gas stove and unscrew the valve body, taking out a spring and a plug.
  • 360-degree rotation of the handle. This problem is often caused by prolonged use of the gas stove. The reason can be the breaking of the knob’s seat. To repair it, you need to buy and put another handle.

You can fix these problems yourself, but if you are not confident in achieving the result by your own efforts, it is worth calling a specialist.

The less often you clean the handles, the more likely you are to have problems turning the handles. Stale grease over time “hardens”, and its cleaning is much more difficult

All of these difficulties in operation, as well as breakdowns, occur when the gas stove is not cared for. In order not to call a master for troubleshooting it is worth to treat your appliances with care, doing their maintenance in time.

If you discover a gas leak or a breakdown of the gas stove, you should immediately call a technician from the gas company you have a contract with.

#87 Почему гаснет конфорка газовой плиты- не работает газконтроль.

Conclusion and useful video

Here are collected videos, which demonstrate the procedure for removing knobs from gas stoves of different models.

This video shows how to remove the knobs using a Gefest gas stove as an example:

The order and methods of cleaning the handles are demonstrated in this video:

Another way to clean gas stove knobs can be seen here

To summarize, it can be noted that the cleaning of all elements of the gas stove should be carried out regularly. The main moving element. the knobs. They are also subject to contamination and may not work well over time. It is necessary to remove them yourself and conduct a thorough cleaning.

It is always worth adhering to safety precautions when performing the work, as well as carefully follow the algorithm of actions so as not to damage these elements.

Want to tell you about how you removed the handles from your gas stove? Share with other users the challenges you encountered. Or maybe you would like to recommend an effective tool for cleaning the knobs and the surface of the stove, which we have not mentioned here? Write your tips and Комментарии и мнения владельцев in the Комментарии и мнения владельцев box below this post.

How to remove the top cover Electrolux gas stove?

To remove the top cover of your gas stove, you need to have a tool handy to help you. Using a tool, you are free to remove the lid, using a screwdriver to get into the special grooves, and the lid will remove. Then carefully remove and place on the floor.

The front panel is secured with two self-tapping screws from the bottom, two screws hold the gas taps and remove it down. Slide the two latches inside, releasing the fastening of the front of the table, unscrew the four self-tapping screws on the back of the stove, and the eight self-tapping screws on the burners. No workbench. The worktop is removable.

What is the cover for on the gas stove?

The cover, when raised, has a protective function. It covers the ceramic tile from splashes of grease, steam and overheating tiles, dust and condensation. When the apron is made of tempered glass or tiled, the materials can withstand high temperatures and are not difficult to clean.

In fact, the bottom compartment of a cooktop with a drawer has been designed to keep food already cooked at an optimal temperature. In this drawer, dishes do not burn, do not cool and do not lose their taste Thanks to serving dishes in heated plates, food will stay warm longer.

Variety of choices

The company started producing stoves in 1995, when it bought Tekhnogaz SA (a manufacturer of such appliances). Today, the range includes gas, electric and combined devices. As a rule, they have standard sizes. The height of the products. 85 cm, width. 50-60 cm, although some models have this figure reaches 90 cm. The depth of the hobs is 50 cm.

The gas stove is the most common type of device. The surface of the products is made of stainless steel or covered with enamel. The most often used color is white. The cooking surface has 4 burners of different sizes. On the control panel there are knobs, above which there are pictures. They indicate each knob belongs to the corresponding burner. Burners with different capacities and sizes allow different cooking speeds: fast, medium and normal.

Many Ardo gas stoves are equipped with an electric ignition switch. This is very convenient because it does not require the use of matches. This method is also safer if the stove is used by children. This mechanism can be turned off and then on again if needed. You can always light the stove by hand, with matches.

The scheme of electric ignition in most models requires a safety mechanism for the thermocouple. This means that every burner has a gas safety system called “gas control. In the case of accidental extinction of the flame, the thermocouple is not heated, the charge disappears, and the valve in the system is closed. Fuel supply is interrupted.

In almost all models, the hob is equipped with a glass lid. As it may crack during heating, it is necessary to wait until the burners cool down completely. Only after that you can put it down.

If desired, the upper lid can be removed.

It should be noted that in modern models, this manufacturer does not use a piezor ignition, in contrast to the electric variant. The fact that the piezo igniter is a low-power and unreliable device, reducing the quality of the product.

The gas oven and grill have manual override and electric ignition. Most models have a gas control mode. Oven is equipped with a timer for 1 hour of operation. Additional accessories come with the device. The inside of the oven is easy to clean.

For example, the Ardo KTLE 6640 G6 inox gas hob is made of stainless steel. Its dimensions are standard 85: 60: 60 cm. On a cooking surface are located 4 burners with different power (from 1000 to 3100 W) and speed. Manual override and electric ignition are available. No gas burner control system. The grids and burner caps are made of cast iron. The cooking surface is equipped with a glass cover.

Oven and grill is gas, capacity 52 liters. Available:

The oven is either electrically or manually ignited. It has gas control. Enameled tray and tray, the grid are available as accessories. All the necessary utensils are stored in the drawer. The appliance can work both with mains and with liquid gas. Nozzles are included with the appliance.

Electric ovens

The bodies of the brand’s electric stoves are made of stainless steel or coated with enamel. The hobs are either glass ceramic or cast iron. Electric burners are available in 3 versions:

Normal and fast burners work in 6 positions, which can be adjusted by the regime switch. Automatic burners work in 12 positions. Fast cooking zones enable you to create a dish in the shortest time possible. Automatic burner hobs allow you to save energy.

The ceramic glass top is completely smooth. Burner zones are limited to circles. Heating takes place only inside them. When the temperature reaches 60° C, the indicator light comes on. If the temperature drops below this temperature, the indicator light goes out. This is a residual heat indicator. The on/off switch has 6 or 12 positions.

Ceramic hobs have undeniable advantages. First of all, it is the speed of heating and cooling. Also worth noting non-stick properties. However, due to the fact that the material is quite specific, it requires some precautions during operation.

For glass ceramic hobs, some models support the Hi-Light heating type. This is a more advanced system that allows the product to heat up in 5 seconds and has a better heat output.

Ardo electric ovens have 2 types of convection:

Natural convection is achieved by heating from below with 1 burner.

For most types of baking and roasting, this is not enough, since this one-sided mode does not allow for an even and beautiful baking of the dish on all sides.Forced convection will help in this case. A fan provides the action, forcing hot air to disperse throughout the oven. This means that your food is subjected to a certain temperature on all sides. It is evenly baked, not over-dried. It also has a delicious browning crust on its surface. Forced convection allows multiple temperature settings.

The brand’s electric ovens provide defrosting, reheating, conventional and fast cooking functions. They are equipped with several heating elements, which work simultaneously or in isolation. This significantly improves the quality of cooking and allows you to bake more sophisticated dishes. Electric grill and rotisserie further enhances the culinary possibilities.

The Ardo CS: GO 60 EE F inox is a great stove with more features. The height of the device is 85 cm as standard, while it is 60 cm wide and deep. The cooking surface is glass-ceramic with a type of heating Hi-Light. There are two cooking zones with a diameter of 14.5 cm and an output of 1200 watts. There are also 2 fast cooking zones with a diameter of 18 cm and a power of 1800 watts.

The electric oven has a capacity of 55 liters. In its arsenal has 7 functions:

  • defrost in room temperature mode;
  • Lower and upper heating;
  • bottom, top heating convection;
  • grill thermostat;
  • grill convection;
  • grill: Lower convection heating;
  • Grill: Rear heating convection.

In the case of overheating, the appliance has a temperature limiter.

There is a timer that allows you to set the start and end of the cooking process. Thermostat operation is controlled by indicators. The oven door is equipped with heat-resistant glass. There is a drawer for dishes.

Widespread breakages of gas stove

According to the rules of safe use of gas appliances, all repairs should be carried out by a qualified specialist of the gas service. In case of serious damage to the gas stove, the consumer must contact the company with which he signed a contract for the maintenance of gas equipment.

However, this applies exclusively to complex situations where any unauthorized interference with the gas equipment could endanger everyone in the house.

In the case of a gas leak, you should not try to fix the fault yourself, and you must urgently call specialists from the gas service to carry out repair work

If the failure in the work of the gas stove did not occur due to a leak of blue fuel, then there is a very real chance to make repairs without the help of a master.

Some of the most common faults that can be handled with your own hands include:

  • Lack of flame when lighting individual burners;
  • Failure or blockage of the ignition electrode;
  • Unstable functioning of gas control;
  • Breakage of the oven door fasteners;
  • tight turning of the gas tap.

Before you repair a gas stove, you should always cut off gas access to the room, even if the breakdown is in no way connected with the problem of fuel supply. As an additional precaution, it is better to open the window or the front door.

Autarkes Ceranfeld anschliessen Kochfeld anschließen mit Duspol Küche 400V Starkstrom Anleitung

Gas workers strongly recommend that during repairs, the piezo ignition is completely turned off, so that in the event of accidental damage to the gas equipment does not provoke an explosion.

Repairing a Gas Hob

Before proceeding to repair the gas stove, it is worth familiarizing yourself with its structure and operating principle. If the problem is a clogged burner nozzle or a faulty piezo, you will need to remove the top panel to make the repair. Before dismantling the gas stove, you must completely disconnect the gas system by closing the appropriate tap on the pipe and disconnecting the electricity supply.

Next, remove all the bolts connecting the top panel with the control panel. They are under the burners, so first you need to remove all four burners. To remove the top panel, some effort will have to be made to release it from the clamps.

To access the gas burners, you will need to remove all the grids covering the burners and located on top of the stove

Having successfully removed the top panel, proceed to remove the control panel. First of all. remove all handles from the stove, and unscrew the bolts. Often these screws are located at the bottom, although depending on the model they may be in different places.

If all the connecting elements have been safely removed, start pulling the panel, pulling out the buttons in parallel and pressing the clamps to the body. With just a little effort, you can quickly remove both panels and proceed directly to diagnose the device.

Failure. burner clogging

Interruptions in the work of burners. the most common breakdown of the gas stove with which it is quite real to cope with their own hands. In this case, when igniting the burner, the flame may burn very weakly or disappear altogether.

This can be caused by a clogged flame spreader or nozzle due to lack of care in the use of the appliance. While cooking, leftover food or grease can get inside the nozzle, so the burner may not light up at all.

It is not recommended to use metal objects (needles or spokes) to clean the nozzle as this may damage the part

In this case, the only option is to clean the nozzle with a wooden toothpick, pre-sharpening it with an ordinary paper knife.

If you want to clean the nozzles as best as possible, then the best option is to unscrew all the screws, and open the lid of the gas stove, but you must be very careful not to damage the device. For more effective cleaning of the nozzle, it is recommended to unscrew it beforehand.

Another problem that owners of gas stoves may encounter is the noise produced by a burner during operation. What to do in this situation

Failure. problems with the ignition

Electric ignition function in gas stoves greatly simplifies the life of the modern user, but does not always work properly. To identify the exact cause of the breakage of the piezo element, you should first of all find out whether the cause of the lack of flame of the burner is really a malfunction of the piezo.

Check for debris on the ignition element surfaces. Even if a small drop of water got inside the nozzle, the burner will no longer ignite.

In the case that only one burner doesn’t work, it is worth checking the ignition electrode. If there is a crack on its surface, the problem of the lack of flame is in it. The spark simply shoots to the side, not reaching the burner flame spreader.

The ignition switch can not work on a single burner, or all burners, so to identify the cause is important to carefully examine each element of the ignition switch

Before proceeding to repair, it is necessary to remove all burners and open the lid of the stove. If when you press the igniter button, the spark does not jump only in one burner, then the cause is a faulty spark plug (electrode), on which a crack has formed. Only if all the burners do not ignite, it is probable that the problem is caused by a damaged wire between the piezo and the ignition module.

After removing the top panel of the gas stove, press the ignition button, which will help determine the cause of the malfunction of the igniter. If the wire is actually damaged in any area, you will see a spark popping at the point of damage.

Regardless of how the breakdown occurred, due to a crack in the electrode or a damaged wire, there is only one way to fix the gas stove auto ignition. replace the broken part with a serviceable one.

Breakdown. the gas control doesn’t work

Any gas stove is equipped with a special gas control system, which provides control of gas leaks during the operation of the equipment. This system is called a thermocouple, and looks like a small metal pin located near each burner.

Even if the flame is extinguished for some reason, the thermocouple does not allow the gas to spread, and thus prevents an emergency situation.

The first symptom of thermocouple failure is a rapid attenuation of the flame immediately after lighting the burner

The gas-control element can fail due to a trivial clog, which can be formed in the course of operation of the technique. In this case it is enough to clean the thermocouple from the accumulated grease and dust with a simple emery paper.

If even after cleaning the element, the burner of the gas stove still fades, you will have to make your own repair of gas control, disassembling the panel and installing a new thermocouple.

Failure. failure of the door

The most common oven problem is the inability to fully close the door. Such a malfunction can occur as a result of excessive load on the door itself, which is why it is not recommended to put heavy objects on it, for example, pans, trays.

Photos of ARDO repair with disassembly to the base.

On this page we have picked up photos of disassembly of the Ardo up to the frame. The case of disassembling an Ardo down to its component base was a prime example of what happens to appliances in intensive use. So let’s see some pictures of the repair.

Let’s take off the back cover. the picture shows elements of electrical circuit, a part of the pipe and the stainless metal of the drum. The wiring is pretty neatly done. Insulated wires are bundled up and neatly plugged into terminals.

In the next photo, the yellow and green ground wires and the stainless steel metal rim are especially nice. The electronic module and terminal strip turned out a little blurry.

Side view of the rear of the washer. The wheel that transmits torque to the spinning drum; the tank cross that gives it rigidity-are high-quality castings. Heating element inside, connected by black and white wires. Power cord and drain hose in the frame.

All details ARDO: Antonio MERLONI SPA; Via Vittorio Veneto, 116; 60044 FABRIANO (AN) ITALY; Model WD1000X 20014624179 05 Made in Italy; 230V 50Hz, IPX4 0,05-1Mpa; 5kg 2,5kg 10A 2200W; type ME03 PCT. product certification.

ARDO front panel. a reflection of Italian design: round and rounded knobs, oval buttons and indicators, apotheosis- Made in Italy. Let’s have a closer look: BIANCHI CON(SENZA) PRELAVAGIO, COLORATI RESISTENTI DELICATI. Further inscriptions: RISCIACQUI (AMMORBIDENTE) E CENTRIFUGA, SINTETICI CON PRELAVAGGIO. Number of revolutions 1000/500, scales, pouring water, cancel centrifuge, on/off. Temperature regulator 30 to 90 degrees Celsius, washing time, program selection. SINTETICI SENZA, TESSUTI MISTI DELICATI, SCARICO, LANA. The inscription on the hatch 20014624179 014105018 01 05. Green light bulb 220 Volt, perforated stainless steel drum.

Another ARDO model

This picture shows the EasyLogic class AE1010. As in most of the models, the tray for SMS. synthetic detergents is on the left side. Control knobs, knobs to the right. Center and center. Buttons: Start, Preliavaggio, Risciacque. Speed controller: 500, 600, 700, 750, 800, 900, 1000 rpm. Indicator of modes: Prelavaggio, Centrifuga, Lavaggio, Fine/End. Temperature control from 90 degrees for Cotone cotton to 30 Celsius for delicate washing and linen. Button: on/off switch.

Top view: concrete weight- counterweight to reduce vibration. Dosing valves for detergent, pressostat, electronic control circuits with electrical wiring.

Side view: 1000 rpm 45SX-45DX 220-240V/50Hz, MINISEL CF 42 14/03/2003 546042300.03 S1-20300679 on gethinax board. Transformer and resistors, triodes and microcircuits, capacitors and power control switches on gethinax electric board. The connectors are soldered to the board, the wires are bundled and wrapped with electrical tape.

Two brown push-buttons. elements of logic, depending on the filling they turn on one or the other mode. Plastic levers, spring, screws.

Lower rear of the washing machine. At the bottom of the motor is connected to the drum by a V-belt. Beside there is a heater and a temperature sensor. The motor and the heating element are firmly grounded with the yellow-green wire.

The tank is made of white plastic, the element with 18 ribs. The five-point wheel accepts the V-belt and provides the desired drum rotation speed.

Stainless steel drum cover. Shaft and sleeve not oxidized and not rusted at all. well chosen composition of steel with low impurities.

Разобранная задняя крышка у ног мастера. Кое-где видны подтёки ржавчины. В целом конструкция надёжная, но некоторые детали от интенсивного трения все-таки ржавеют. Ржавчина при большом обилии может загрязнять белъё, оставляя рыжие или желтые следы, точки.

Городской сервисный центр VM ремонтирует на дому бренды(марки) модели бытовой техники

“Ваш-Мастер” ремонт стиральных машин автомат в области. Сервисный центр: 7 (495) 641-09-23. Отдел запчастей: 7 (495) 782-66-02. Адрес: 141109, Щёлково, ул. Талсинская д. 59, с. 5. Телефон: 8(496 56) 9-63-39

Author

Laidred

| Denial of responsibility | Contacts |RSS