How to remove the ariston washing machine Ariston Hotpoint

How to remove the top cover from the HotPoint Ariston washing machine?

To remove the top cover of Ariston washing machine, they need to be unscrewed from the rear wall of the cross or hexagonal screwdriver. Then push the lid in the opposite side of you, raise up and set aside.

• Go around the technique from the back;
• Find and unscrew the screws holding the upper cover (they are located respectively in the left and right of the upper corners directly under the protrusion);
• pull the panel over yourself;
• Then lift the lid and remove it.

How to remove locking from Ariston washing machine?

Remove the cuff, which is located between the hatch and the washing machine drum. In order to remove it, you need to extract a clamping ring with a spring. On the right we see a lock, holds on two screws, unscrew them. After that, remove the cuff from the frame of the hatch and reach the lock through the removed cuff.

To remove the lid from the washing machine, you must first move it away from the wall so that you can have an approach to the rear wall of washing, after the cover is unscrewed, you need to remove it, for this you need to move the lid back relative to the washing machine, and then raise it up and raise it up and Remove to the side.

Where is the mesh filter in the washing machine?

On all machines, the filter is installed in front of the filler valve directly in the hole, where the water supply hose to the machine is screwed. Looks like a round plastic mesh with small holes.

The dirt accumulates in the drain filter, the folds of the cuff, the powder receiver, on the case, etc. So that at one “wonderful”, the washing room does not refuse to work, you need to serve it in a timely manner. We will figure out how to clean the washing machine from garbage.

How to replace the cuff of the armor of the Ariston washing machine (Ariston)

In order to replace the ARISTON (ARISTON) washing machine, it is necessary to access the inside of the machine through its front wall of the case. Rubber sealing cuff is one of those elements that are most susceptible to wear and damage. This happens for various reasons. The damaged cuff causes the leak of the washing machine, and if a fungus or mold was started on it, then the cause of the unpleasant odor and the source of unsanitary conditions.Before starting the repair, it is necessary to disconnect the washing machine from the network and put forward it, providing access to the back wall. Then unscrew the two screws of the cover mount. To remove the lid, it must be moved relative to the machine body towards the rear wall, and then lift the front edge and disconnect. Then provide access to the front wall fastening. To do this, put forward and remove the dispenser for detergents. Under the dispenser there are fixing screws of the control panels, which must be unscrewed. To remove the lid, it must be moved relative to the machine body towards the rear wall, and then lift the front edge and disconnect. Then provide access to the front wall fastening. To do this, put forward and remove the dispenser for detergents. Under the dispenser there are fixing screws of the control panels, which must be unscrewed. After removing the mounts, disconnect the control panel, observing caution so as not to damage the latches with which it is fixed to the body of the Ariston washing machine. Thus, the upper part of the front wall is freed, go to the lower part. Using a flat object, disconnect the base panel, which performs a decorative function. Now all the fasteners of the front wall are freed and visible. To unscrew all the screws of the wall mounts in the upper (usually two screws) and the lower part (two or four screws). Find a fastener tension spring on the lamp rubber cuff. Using a flat object, lift a spring, and stretching it, remove the clamp. Now all the fasteners of the front wall are freed and visible. To unscrew all the screws of the wall mounts in the upper (usually two screws) and the lower part (two or four screws). Find a fastener tension spring on the lamp rubber cuff. Using a flat object, lift a spring, and stretching it, remove the clamp. Disconnect the front edge of the cuff from the front wall of the washing machine. Unscrew the mounting screws of the hatch lock device, disconnect the lock. Gently lift the front wall up and disconnect from the case of the machine. Thus, access to the internal elements of the Ariston washing machine for further repair and replacement of the handle of the hatch door was obtained. We continue to disconnect the cuff. At the top right, it is connected to the drying air duct using a layer. Having taken the edge with your fingers, disconnect the layering from the metal duct along with the plastic clamp. Go to the second clamp that pulls the cuff around the plastic tank. In the photo on the right is a clamp, which is pulled and fixed with gear latches. To disconnect the teeth and loosen the clamp, it is necessary to use a slotted screwdriver. We continue to disconnect the cuff. At the top right, it is connected to the drying air duct using a layer. Having taken the edge with your fingers, disconnect the layering from the metal duct along with the plastic clamp. Go to the second clamp that pulls the cuff around the plastic tank. In the photo on the right is a clamp, which is pulled and fixed with gear latches. To disconnect the teeth and loosen the clamp, it is necessary to use a slotted screwdriver. After removing the second clamp, the rubber cuff of the hatch is freely disconnected from the tank around the perimeter. Before installing a new cuff, it is necessary to carefully clean the seat on the plastic tank of the washing machine. This is necessary for the tightness of the installation. Also, before installing the cuff, you need to combine the holes in the cuff for draining the water with the lower part of the tank, and the layering with the duct of the drying. Before installing a new cuff, it is necessary to carefully clean the seat on the plastic tank of the washing machine. This is necessary for the tightness of the installation. Also, before installing the cuff, you need to combine the holes in the cuff for draining the water with the lower part of the tank, and the layering with the duct of the drying. Installation start with an attachment to a dryer dryer. The next step is to combine the drain holes with the lowest point in the middle. After combining the holes, you can attach the rest of the cuff to the tank, as shown in the photo in the center and on the right. The photo on the left shows that the fastening of the cuff and duct of the drying is pulled out by a new clamp, but in the absence of that, you can use the old. Then it needs to be worn along with the lifting, and the metal duct must pre.process with a small amount of detergent to reduce the resistance. After the new cuff is worn on the tank, it must be pulled off with a clamp, as shown in the photo on the right. The photo on the left shows that the fastening of the cuff and duct of the drying is pulled out by a new clamp, but in the absence of that, you can use the old. Then it needs to be worn along with the lifting, and the metal duct must pre.process with a small amount of detergent to reduce the resistance. After the new cuff is worn on the tank, it must be pulled off with a clamp, as shown in the photo on the right. Further repair and side of the Ariston washing machine in the reverse basis of disassembly. When the front wall is dressed and the cuff is attached to it, it is necessary to check the tightness of its installation. To do this, fill the tank with water to the lower edge of the hatch. If the cuff leaks at the junction with the tank, then the reason for this may be either a not thoroughly cleaned seat or insufficient tension of the clamp. After the tightness is checked or restored, the final assembly of the washing machine must be made.

The distinguishing features of Ariston washing equipment are the quality and full compliance with the technical standards that are advanced

For large chil of modern models of washing machines, Ariston (Ariston) is characterized

Forced opening with a cord

A thin synthetic cord can help open the hatch of the machine if previous actions have not brought positive results. The disadvantage of this method, invented by the craftsmen. it does not always fit. The reason for the castle design. If the tongue is clicks towards the case of the machine, then it will open, and if from the case or up, this method will give nothing.

• Prepare a piece of a thin and strong cord or fishing line in size of the manhole with a small margin.
• Set up from the side opposite the castle.
• Take the cord into the gap between the body and the hatch throughout the circle, and hold both ends in your hands.
• Pull the cord so that it presses on the latch.

If the door did not open as a result of this, then the design of the castle of a different type and only one option remains. remove the top panel.

Several ways to open a locked door after an emergency stop of a machine

The correct diagram of unlocking the hatch of a certain model can be seen in the instructions attached by the manufacturer. But it happens that this document is lost, so we consider the most effective ways to safely open the hatch.

How to open the door of the machine with horizontal loading

First you need to carry out several manipulations that relate to all brands of machines with horizontal loading.

• Pull out the outlet cord.
• Look at the hatch window and make sure that there is no water in the tank. If it has it, it is necessary to drain through the emergency hose or unscrew the plum plug and substitute the basin.
• You can also drain water by lowering the machine hose below the tank level.
• Open a small hatch on the front wall (drainage filter) and see if there is a cable of emergency opening in your technique. Basically, it goes a bright yellow color. Gently pulling the cable, you can unlock the system of the machine door.
• But not every washing technique has such a cable. If it is not, then to open the hatch you need to remove the top cover, tilt it back so that the tank moves away a little. Then find the lock lock and push it away. To remove the lid, it is necessary to unscrew two bolts that are at the end of the equipment, carefully raise the lid and remove it.

How to unlock the hatch of a vertical loading machine

If a machine with vertical loading, then the door opening scheme will be slightly different. You can just try to turn off the machine from the network, since often the lock occurs simply due to the interruption with the signal. When de.energizing the machine, the signal disappears and in some cases the door opens. Many washing machines have memory, so after turning on the door will remain blocked. You can just try to reset the program, and then press the “Except”, “Drain”, “Dragging without spin” or “squeezing”. Having completed the process, the door is automatic unlocked.

Pressing the program reset button on a typewriter and the next selection of the drain mode will help complete the washing process and automatically unlock the door

A quick way to open a lock in washing equipment with a vertical loading system

The door does not open if the pump is malfunctioning, the drainage has broken, the control module or water control sensor has broken. In any case, you need to open the hatch to pull out the unpleasant linen, and then deal with the further causes of the breakdown. If the door jammed in the typewriter, this means that the drum was poorly closed, and it simply scroll through the open form. Maybe the system fails, turned off electricity or water.

• Push the machine away from the wall.
• Disconnect from power supply.
• Unscrew the back cover bolts and remove it.
• Since the whole problem lies in Ten, we need to remove the belt and unscrew the bolt that holds it. We remove all the wires that will interfere with work (if necessary, they can be signed so as not to forget the location).
• With the help of a screwdriver, we carefully try to remove the heater with a sealing elastic band. Sometimes it is hard to do, as the elastic bands gets to the body.
• We pull it out of the machine and then, using the screwdriver, try to close the door of the drum and turn it upstairs.
• We insert the heater back and connect all the wires.
• When a closed drum rises in place, the machine hatch is unlocked.

Manipulations with a machine must be carried out very carefully, since you can accidentally damage the heating element and other details of the technique. When electricity is turned off, the door can be unlocked automatically

Even if the upper cover opens, the water will not spill out of the drum.

Any repair of the washing machine with vertical loading should be spilled carefully, trying not to damage the heating element and other parts

How to force the hatch if the handle breaks

When breaking the handle, you will have to work a little to open it on your own without involving a master. There are several options:

• take advantage of the cable of emergency opening;
• use wire or rope (the method is indicated above);
• Gently capture with pliers what remains of a non.working handle and try to pull, until the click appears;
• try to open the lock through the upper part.

Is it possible to remove the top cover of the washing machine?

Removing the upper cover of the washing machine will not require careful preparation, and you will only need a screwdriver from the tools. give preference to the cross type. Important! The upper panel is attached to the back bolts. Therefore, if your washer is installed close to the wall, you need to put forward a machine.

On different models of Ariston washing machines, you should remove the rear or front panel of the case, then disconnect the wires, unclench the fixing clamps that attach the drain pipe and the hose to the pump snail, and then remove the pump connected to the snail. Cleaning the drain filter is easier through the hole for the drain pipe.

at first

Let’s start our narrative with a standard warning. Remember that only a certified master of the specialized service center can be guaranteed to repair the Ariston washing machine. Self.repair can lead to aggravation of the problem.

Nevertheless, if you are determined to repair the Ariston washing machine with your own hands, it will be nice to study the instructions for disassembling it. So you can avoid unnecessary mistakes, save time and money. Where to begin?

note! The drain of the spent water of the Ariston washing machine can be connected both to the removal of the siphon of the sink and to the removal of the sewer pipe. And in that and in another case, it is easy to turn it off.

• Next, without disconnecting the bulk and drain hoses, we will twist them somehow so that water does not pour to the floor, and we will fix the ends on the case.
• Taking advantage of someone’s help, drag the washing machine to where it will be convenient to disassemble. Under the car you will need to lay something so as not to fill the floor with water.
• We take out the powder receiver from the car and remove it to the side.
• We unscrew the drain filter and lower the exhaust water remaining in the tank. At this stage, so far everything.

Now we need to prepare a simple tool. You will need a hammer, pliers, a basket and head for 7, 8, 12, 14 mm, an open key of 8 and 10 mm, a special key for removing the counterbones of the Ariston washing machine, screwdrivers. cross, hexagonal, lubricant for washing machines, wooden bar automobile puller, awl, multi.colored markers, knife.hacksaw for metal. Having collected the entire tool, we return to work on disassembling Ariston washing machine.

• We approach the Ariston washing machine from the side of the rear wall and, armed with a cross blade, unscrew several screws holding the lid of the service hatch.
• Having removed the service hatch, we get access to many details: the pulley of the drum, the drive belt, the motor, the heating element and the temperature sensor.
• Now we unscrew the 2 self.tapping screws with a cross with a cross, holding the top cover of the Ariston washer.

Replacement of the bearing

To remove old bearings, you will need a removable device. In the absence of it, you can use a metal rod and a hammer. If you have never performed such an operation before, it is better to resort to the service of the master.

The AVL 109 models have bearings 6205 and 6204, as well as an oil seal with a skirt of 65 x 30 x 52 x 10 mm. This marking is deciphered as follows:

If you decide to replace the bearings with your own hands, you need to perform the following sequence of actions.

A metal rod and a hammer need to knock out the old bearings. The cross must be placed on the stops so that there is free space under the bearings. The operation must be carried out with the ultimate accuracy.

To install a new bearing, you need to take a hammer and very carefully sew it in the planting nest, tapping at the edges of the outer clipping clip and slowly moving in a circle. Then, when it almost completely enters the nest, the old bearing should be put on top, using it as a guide, and, tapping with a hammer, completely plant a new part in the nest.

Before putting the cross.cutter, it is required to clean the “zero” sandpaper and a rag of the drum shaft, as well as the front surface of the tank. in the place where the oil seal will be in contact with the tank. You also need to lubricate the surface of the oil seal. To do this, you can use a lubricant with molybdenum.

The crossman must be carefully installed on the shaft. To do this, use a hammer, carefully tapping them along the edges of the cross.

Assembly is carried out in the reverse order.

As you can see, with certain skills, you can independently repair your washing machine. When working with other models, deviations from the above sequence of work are possible, but we described the main stages.

Useful tips

Independent replacement of the bearing in a branded washing machine automatic to many users seems very difficult. To simplify the implementation of such a task, you should listen to some useful tips and recommendations.

Dirgining the design of household appliances, be careful. Act carefully and carefully so as not to accidentally damage important elements of the device. Fold all small fasteners in one place or put in a bag so that you do not lose them later.

During the disassembly of technology, it is recommended to photograph the location of all contacts, bolts and parts. At the end of the repair work, you will have an exact scheme of what parts and in what places should be located before your eyes. Thus, you will protect yourself from many mistakes.

Having knocked out the old bearing, you need to carefully monitor the position of the bite. If the tool accidentally jumps or slides, and the blow will have to be on the inner ring, then it risks flying out

The rest of the bearing to remove from the nest will be an extremely difficult task.

It is important to correctly install not only the bearing itself, but also the oil seal. If the installation of the latter is neglecting and frivolously, then it will quickly begin to let water, which will eventually provoke the deformation of the bearing.

Suitable bearings for the HotPoint-Ariston washing machine any model can be found not only in specialized stores, but also in various services

Going for a purchase, grab the old details that were present in your technique.

When installing a new bearing, make sure that it fit the closestly as possible to the sleeve. Otherwise, the details will pass water, and it will return back to the drum, you also need to pay attention to the crossbone of the fasteners.

Before in a hurry to collect the drum, it is recommended to replace all the old seals and apply a sealant. These procedures will be needed so that in the near future you do not have to resort to repair work again.

After completing the repair work and collecting a washing machine, it is recommended to carry out test, trial washing in the tank should not be things, you should not set a very high temperature-60-70 degrees should be set.

If during the work you are afraid to accidentally damage the glass of the hatch door, it is recommended to first remove it. To do this, carefully unscrew the screws attaching the loops of the door. After that, it must be removed to the side.

Before starting all work, it is recommended to make sure that there is access to household appliances from all sides. Then it will be much more convenient to repair it.

Having pulled out the drum, it is best put on the cuff. Otherwise, you can accidentally damage the fasteners and plastic components of the structures.

Before starting to independently change the bearing in the HotPoint-Ariston washing machine, you need to know that to carry out such repair work, you will have to disassemble the equipment almost completely. If you are afraid to make a mistake and do not have at least the slightest experience in such matters, it is better to entrust the procedure for specialists. Otherwise, you risk causing even greater harm to the device.

About how to replace the bearings in the HotPoint–Ariston washing machine, see further.

Problems with blockages

If you have problems with the clogs on the HotPoint Ariston washing machine, do not rush to call the master, everything can be repaired quickly, with your own hands. How to find out that you are dealing with a suction? The main sign of blockage in the drain system is the idle operation of the drain pump, that is, it is buzzing, but the water from the tank does not leave. Typically, this nuisance manifests itself after the end of the washing, the machine machine cannot drain the spent water to start rinsing and freezes, or it drains the water too slowly.

Strong blockage can be in several places:

• In the drain pipe, between the tank and the drain filter. this happens less often, since the pipe is quite thick;
• In the drain filter. there the blockage is most often formed;
• In the pump. in Ariston washing machines, blocks in the pump are infrequent, since an additional filter is installed in front of the drain pump;
• In the drain hose. blockages rarely occur, mainly in cases where the hose was set incorrectly.

How to quickly eliminate blockage? First of all, you need to check and clean the easily accessible places of the washing machine, where the blockage could occur. First we unscrew the drain filter, which is located at the Ariston machine right below under a narrow panel. Before you unscrew the filter, put a rag, because water is pouring from it. Remove all the garbage from the filter, and then tighten it back.

Then it is important to check the drain hose and sewage. In a number of situations, a banal blockage in the drain pipe can force the user to contact the machine repair specialists when it was more correct to contact plumbers

And if everything is in perfect order, then you will need to disassemble the machine, clean the nozzles and the pump. To remove the pipe, you need to weaken two clamps, and to remove the pump you need to turn it off from the sensors and unscrew two fasteners.

In case of any malfunction, the “washing” Hotpoint Ariston gives an error with a certain cipher displayed on the screen

It is very important to correctly recognize the codes of errors in Ariston washing machines, because this is a direct hint indicating the cause of the breakdown

A pump and a water intake valve failed

It is quite difficult to confuse with other breakdowns of the HotPoint Ariston washing machine with other breakdowns of the Symptoms. When the filling valve stops blocking the water, the water begins to go into the battery of the washing machine by gravity, even if the “home assistant” is turned off from the network.

To check the filling valve, it is necessary to remove the top cover of the HotPoint Ariston machine, unscrewing two fasteners. The valve is located at the junction of the pouring hose with the machine case. First of all, we check the gaskets, if they are intact, then you need to measure the resistance of the device, and for this you will have to use the multimeter. Install the probes on the contacts of the filling valve and check. The device should show from about 30 to 50 Ohms.

The faulty filling valve should be replaced with a similar, independent repair is impossible. The replacement itself is made very quickly, we unscrew the old valve from the housing and screw the new one, not forgetting to connect the sensors. Worse if a pump is out of order, because this is a fairly expensive detail.

The faulty pump gives itself during washing, when the machine should drain the water, but it does not, while the pump either does not make any sounds at all, or it buzzes, but the murmur of the drained water is not heard.

In the HotPoint Ariston washing machine, it is located in the lower part and you can get to it through the bottom. It is better to check and replace the drain pump, but you can do everything with your own hands, the main thing is to thoroughly study the work course.

How to remove the top cover of Ariston washing machine?

To eliminate almost any breakdown, you will have to remove the top cover of the Ariston washing machine. The work takes no more than 10 minutes, but the novice master may have some questions in the process. We will tell you how to partially disassemble the body of the washing room yourself, at home.

Unexpected difficulties

Most washing workers have no problems with removing the upper panel. it can be easily removed without any special efforts. At the machines, a hotpone Ariston cover is additionally fixed with cast latches. Plastic fasteners are very easy to break when disassembling, so the work is evaluated as a rather risky.

When removing the top panel, it is impossible to break off the latches, otherwise it will not be possible to install the lid in place.

It is also important not to forget about safety regulations. Before you try to open the lid, you should turn off the washing machine from the network, and also block the shut.off valve. Only after such preparation can you start disassembling the case.

Dismantling the element on a typewriter with front loading

The algorithm of action will depend on the type of washing machine-automatic machine. Models with front loading are in great demand, so let’s start with them. The “front.line” lid is additionally fixed with plastic cast fasteners, which are important not to forget. To remove the lid, the user needs:

• find two bolts holding the top panel;
• Using a screwdriver or electric screwdriver, unscrew the screws;
• go around the machine, raise the back of the panel and carefully pull it in your direction until the plastic latches are triggered.

You can not push the lid with a knife or a slotted screwdriver. this will lead to a breakdown of the latch.

This is how you can open the lid on Ariston washing machines. If the “top” does not budge, you should change the tactics of actions: stand in front, press the element slightly and pushing the panel towards the back wall of the case.

The main mistake made by domestic masters is an attempt to “stir” the lid, pushing it with a knife, screwdriver. This will not facilitate the removal, but it can lead to sad consequences. With such intervention, plastic latches often break, and then assembled the body will not work back.

When removing the “top” from the washing machine, Hotpoint Ariston is the main thing not to violate the instructions for the actions. The screwdriver should be used only to unscrew the bolts, it is strictly prohibited to push her lid.

Remove the lid of “verticals”

Removing the element on Ariston machines with vertical loading is more difficult. If the linen hatch is located on top, then with a partial disassembly of the washer, it is necessary to remove not only the lid, but also the control panel. In order not to do unnecessary work, first it is worth clearly determining the purpose of interference in the machine.

If for the repair it is necessary to “crawl” to the hatch door, then only a couple of fasteners can be unscrewed. When you need to climb deeper, you will have to remove the dashboard. To carry out a partial analysis of the “verticals” hotpone Ariston, follows:

• to unscrew the bolts located behind, directly under the control panel, on both sides of the machine;
• slightly tilt the dashboard forward;
• Remove the lid by failing the module from the assault rifle;
• to unscrew the screws that fix the “top” (they are located under the dashboard);
• Remove the lid.

With disassembly of the case, the hotpone Ariston is quite realistic to cope with your own hands, regardless of the “front.line” is, or “vertical”. To open the lid, you should strictly follow the instructions and do not try to outwit the system. It is also important to comply with safety regulations when working with electrical appliances.

How to remove the cover from Ariston washing machine?

How to remove the top cover of Ariston washing machine with vertical loading?

To remove the lid, the user needs:

• find two bolts holding the top panel;
• Using a screwdriver or electric screwdriver, unscrew the screws;
• go around the machine, raise the back of the panel and carefully pull it in your direction until the plastic latches are triggered.

How to remove the cover from the Bosch washing machine?

Remove the top cover of the Bosch washing machine

Take a cross or hexagonal screwdriver, unscrew the car at the back of the car. Now move the lid forward and raise up. Be careful, the edges of the panel can be sharp. Set her aside.

Is it possible to remove the top cover of the washing machine?

If your machine is not older than 10 years, the upper cover in it must be removed. Removing the upper cover of the washing machine will not require careful preparation, and you will only need a screwdriver from the tools. give preference to the cross type. Important! The upper panel is attached to the back bolts.

How to remove the upper cover of the Electrolux washing machine?

How to remove the Cleaner Car Electrolux?

• Stand from the side of the back panel;
• Find two screws located in the corners under the ledge of the cover;
• unscrew them;
• Pushing the lid from yourself towards the hatch;
• Go around the machine from the side of the hatch;
• to remove the top cover, raise it up.

How to remove the top cover of the LG washing machine?

• Go around the LG washing machine.
• Behind, right under the ledge of the upper cover, not far from the right and left upper corners of the machine of the machine, there are 2 screws.
• Having removed the screws, we take the lid with both hands.
• With a significant effort we pull the lid on ourselves until it shifts a couple of centimeters.

How to pull a tray for powder from Ariston washing machine?

It is worth clicking on the tongue in the area of ​​the compartment for the air conditioner and the tray will easily jump out.At the HotPoint–Ariston machine

• We pull the tray for the powder until it stops.
• We take the edge of the body of the tray on the right side and lift it a little up.
• Pull the tray on ourselves and pull it out of the washing machine.

How to remove the front panel of the Bosch washing machine?

• to unscrew the bolts holding it;
• With a thin screwdriver, lift plastic latches available around the perimeter slightly pull up and open the mounts;
• move the panel in your direction to free the lower latch.

How to remove the top cover of the zanussi washing machine?

The upper cover is removed without any problems, we take a cart with a head of 8 mm, unscrew two bolts, take the lid, move it a little to ourselves, and then up. nothing special. But about removing the rear wall of the Zanussi car, this cannot be said.

Is it possible to remove the top cover from the dishwasher?

Is it possible to remove the top cover of the dishwasher to fit under the countertop? If you have an ordinary dishwasher (not built.in), then it is not recommended to remove the top cover. During operation, this can cause violations in the operation of the device, and eventually cause damage to the rest of the case.

How to remove the top cover of the washing machine Becko?

• Go around the washing machine;
• find and unscrew two screws holding the upper cover (they are located under its protrusion next to the right and left corners of the car body);
• Take the lid and pull it to yourself literally a few centimeters;

How to open a door of a washing machine?

Pull out the fork of the washing machine from the outlet and leave for 10-30 minutes. After. gently press on the door in the area of ​​the castle and try to open the hatch again.

How to remove the top cover of the Samsung washing machine?

You need to start the process by removing the upper cover, for which you need to take a screwdriver and unscrew two screws located behind the machine. Then gently move the lid a little forward and remove it from the body. If you need to inspect the pulley and the belt of the motor, just pull the counterweight on yourself.

Remaking and installation of the rib of the Ariston washing machine (Ariston)

Replacing the plastic rib of the Ariston washing machine (Ariston) may be needed in case of mechanical damage to the rib itself or a metal drum. Most often, the cause of the malfunction is extraneous objects that fell into the drum along with the clothing, the destroyed heating element (Ten), the imbalance of the linen during the squeezing.

To start repairing and removing the rib, a thin object is required, a little less than holes in the center of the rib, about ten centimeters with a diameter. In the usual state, the installed rib is blocked by the tongue, which prevents its longitudinal displacement. In order to disconnect the rib, you need to insert a flat object into the hole (on this example the third from the hatch) and feel the elastic tongue that blocks the rib. Gently press on the tongue, move the rib deep into the drum, from itself it will be disconnected from the drum. In the usual state, the installed rib is blocked by the tongue, which prevents its longitudinal displacement. In order to disconnect the rib, you need to insert a flat object into the hole (on this example the third from the hatch) and feel the elastic tongue that blocks the rib. Gently press on the tongue, move the rib deep into the drum, from itself it will be disconnected from the drum. The photo below shows a section of the metal drum of the Ariston washing machine (Ariston) located under the edge. In the photo on the right, the tongue is visible, which holds the rib in the established position. All these elements must be in good condition, not bent or damaged so that the rib is reliably fixed. If the drum in the places of fastening of the rib is damaged, it is necessary either to align it or replace it.

The new rib needs to be checked in its lower part, where it will be connected to the drum. There are hooks with which the rib is easily attached to the drum. How to install a new rib, it does not matter. The main thing is to tightly attach it to the landing place on the drum so as to drown the fasteners on the edge. After that, clutching the rib to the drum, shift it until a stopped tongue works. How to install a new rib, it does not matter. The main thing is to tightly attach it to the landing place on the drum so as to drown the fasteners on the edge. After that, clutching the rib to the drum, shift it until a stopped tongue works. After the repair is completed and the rib is installed, check its stability with the hand. It should hold hard on the drum.

The distinguishing features of Ariston washing equipment are the quality and full compliance with the technical standards that are advanced

For large chil of modern models of washing machines, Ariston (Ariston) is characterized

To replace the ARISTON (ARISTON) washing machine sealing cuff, you need to access

We offer one of the ways to replace the heating element (Ten) of the Ariston washing machine (Ariston). Malfunction

For an example, which is considered below, the bearings of the Ariston washing machine (Ariston) were replaced. AT