Home Electric stoves / gas stoves How to move the socket for an electric stove
Electric stoves / gas stoves

How to move the socket for an electric stove

TRANSFERRING AN OUTLET IN A PANEL HOUSE FOR AN ELECTRIC STOVE (PRICE, WITH THEIR OWN HANDS, WARRANTY, COST)

Transfer socket in a panel house for the electric stove (price, with their own hands, warranty, cost) should perform the master with high qualifications and extensive experience. Improper contact wiring can result in a short circuit in the apartment. Only by following all the connection techniques can safety of residents and normal operation of equipment be guaranteed. For electric stoves in typical houses, there is initially a separate cable line.

A very important point is to check the connection of the wires directly in the socket. This is especially true for 380 V outlets. After all, the location of the phase, neutral and protective conductor is important for the electric stove. If they are not properly reconnected, a short circuit may occur. 2. If the electrical grid is done, the neutral wire will be blue and the protective wire will be yellow-green. If not, we suggest that you sign each wire and terminal on the socket. 3. Once the socket has been removed, our instructions advise checking it for re-use. To do this, inspect the contact part and check for signs of metal tempering, sinks and discoloration on the contact part. The presence of such remarks should make you think about buying a new outlet. Minor burn marks on the contact part can easily be removed with a sandpaper and are not a serious problem.

This decision of the designers is due to the high power consumption of these household devices. With a large cross section of a separate wire provides performance of the device and protects it from voltage fluctuations in the network. It is strictly forbidden to connect electric stoves with surge protectors and household extension cords. Such devices do not withstand high voltages and can catch fire during operation. For this reason, when transferring the electric stove to another place, they increase the cable and install a protected new socket.

How to move the socket in a panel house for an electric stove with their own hands? The cost of work in our company is the best, and provide a one-year warranty! are available!

Transferring the outlet for an electric stove and other electrical work is better to perform before finishing work. An electrician in this case will be able to lay the wires hidden method. in the wall in stroe. If you have already made a cosmetic repair, and you need to move the electric stove, then lay the cable in the racks and channels behind the furniture.

Order the transfer and installation of the socket at a new location for an electric stove in a panel house you can always in our company. Only we have real professionals, who are qualitatively and quickly cope with the work. For all the provided by our experts are given a mandatory warranty. We are always ready to help you, even on holidays and weekends.

Qualified Employees. Staff specialists. a team of universal masters. and narrow specialists in various fieldsHigh Quality. We are interested in regular customers, so we do everything. To make our services to your likingLow Prices. treatment in the company will save you money. We do not need to finish and redoGuarantee. After completion of works we give guarantees for services rendered. up to 1 year

Laying the wire.

In the prepared “glass” on the hollowed out (groove in the concrete) is laid a cable, which will power the slab.

It is a violation of the established rules and regulations on the transfer of outlets. It would be best to replace it, especially if a sufficiently large extension is required. It is also strongly recommended to make an installation margin when running the cable from the junction box, in order to avoid repeated work if this wire needs to be lengthened again. In practice, it is usually difficult to implement, so preference is given to the connection of such a cable, which, according to the PUE, can be performed by crimping, welding, soldering or with the help of clips. Clamping terminals are usually used for independent extension, as special equipment is required for the first three methods of connection.

  • Quick-connectors or screws with special brass lugs. if you want to connect flexible copper conductors;
  • Self-clamp. if you need to connect aluminum wire.

If you want to connect the same rigid copper conductors, you can use any terminal.

Transferring an existing socket for an electric stove by extending the cable

This method combines the previous two, combining all their advantages and leveling the disadvantages. At a much lower cost of work and the necessary materials and labor, this method is not much more expensive than the method with the extension cord, while being almost as reliable as a full replacement of the cable.

The procedure for extending a power cable for an electric stove outlet and running it to the new location of the power outlet is as follows:

Ideally, of course, would be to raise or lower it strictly vertically, move it either in the floor or on the ceiling, and then just as vertically lower it to the right place. But most often, in domestic conditions, it is enough to move the cable, making the wiring horizontally on the wall and fix the place of laying cable for yourself by taking a photo or drawing a plan.

Here I see no reason to describe the disadvantages or advantages of this method of transfer, they are already in sight. This is something in between the first options:

In any case, if you do everything carefully and correctly when extending, choose a good cable and other materials, then the socket for the electric stove in the new place will serve you without any problems for the entire lifetime.

The outlet is in the way. a relocation is needed

So, what we have initially. Bedroom. The socket is about 0.9 m high. There is a sofa bed next to the outlet. If you plug something into the socket (and it is TV), then when you unfold the couch it rips “with the meat”. Familiar?

Naturally, there is a reasonable desire to move the socket with their own hands in another place. closer to the TV and away from the couch. At the same time move without drilling, without noise and dust.

  • the socket from the old place is removed altogether;
  • Connect to the old wires new wires that will go to the new socket;
  • New wires lay in a plastic cable channel;
  • A new outdoor socket is installed plugged in the right place;
  • The old installation box with a connection cover.

How to move a socket Oakey & Son Ltd Electrical Services


And any man with his hands can do it on their own, for a couple of hours, thanks to my manual. Or, as it is fashionable to say now, the case.

Marking the new wiring and the new socket for the electric stove

The new socket for the stove is placed depending on the design of future kitchen furniture. This is either at a height of 10-12 cm from the level of the finished floor, as evidenced by the unspoken rules of installation of kitchen sockets. Or 60 cm above the floor on the right or left of the stove, in a place where there will be no kitchen cabinets close to the wall. 2. With the first variant, the amount of hard work on the assemble of the wall (making a furrow and a niche for the socket) is slightly reduced (read below) 3. In the selected example, let’s consider a volumetric version of the work with the installation of a socket for an electric stove at a height of 50-60 cm from the floor. Under it we make a marking. 4. At the chosen place mark the boundary of the niche for the socket. To do this, buy in advance podrosocket lean against the wall on the front side and trace the perimeter with a pencil or marker. 5. From the marking, draw the borders of the groove for electrical wiring. The width of the groove is made 25-30 mm (under the purchased corrugation ∅ 20 mm with a small reserve). The depth of the hole should be such that the thickness of the mortar, covered in a groove of the cable, was at least 20 mm. 6. We do stroe (furrow) for wiring and a niche for subsocket. This is a more extensive work and for its implementation we choose from a pre-prepared tool:

Underfloor heating in the kitchen: laying heat mat with his hands

move, socket, electric, stove

The easiest way to relocate the electric stove or cooktop, at some distance from the power outlet in the kitchen is to use the extension cord. Everything is simple, plug the extension cord into an existing socket, the same plug is led to the new location of the stove, on this, in fact, the transfer is complete.

Kitchens, as well as bathrooms, refers to the “wet” areas, which have special requirements. The kitchen cannot be relocated into a living room if there is also a living room below (except in the case of duplex apartments). this is prohibited by the Government Decree of January 2006.

The difference between the ways of laying can be seen with the naked eye. open wiring goes on the surface of the wall, and for closed wiring it is necessary to chisel out channels for the cables laid. In the vast majority of cases, the second method of installation is used. even at the stage of planning of the apartment or house on the plan marked places to install outlets and under them in the walls are sawed channels, which are then sealed with cement mortar.

move, socket, electric, stove

Open wiring is used only if the design of the room is made in the retro style, if the house is made of wood, or in some exceptional cases, when it is necessary to do without slotting the wall.

In most cases, if there is a need to transfer a socket with a wire hidden in the wall, there should not be any special problems. of course, you will have to saw additional strokes, but it is generally a solvable issue. There may be another problem. how to move the socket on the wall covered with drywall. If it must be moved a meter or two in the plane of the wall, it is quite time consuming, but solvable task, and when you must install the power socket, then there is either to remove the drywall or install the wiring open.

As an option, you can not remove the entire sheet of drywall, and cut in the right place a piece, and after completing the necessary work and paste it back.

Installing the sub-socket and socket for the electric stove: replacing the old socket for the stove, part 2

Any relocation begins with the installation of a new mounting box, dismantling the old socket and its power line from the junction box. When doing this, it is important not to damage the entire apartment system.

Begin the transfer of the electric stove socket should begin with the removal of voltage in the network, with which it will work. Pay attention even to the possibility of accidental touches, they can be very dangerous.

It is customary to provide a separate breaker for the electric stove in the switchboard. Still, it is highly recommended to check the power point with a two-pole voltage indicator.

The dismantling process is roughly as follows:

move, socket, electric, stove
  • After removing the old outlet, it is important to check whether all of its wires are intact, especially if you own a power outlet with a voltage of 380 V.
  • For the stove to work correctly, pay special attention to the order of connection of phase, neutral and protective wires, since it is their incorrect connection that can lead to a short circuit.
  • If the original network was based on the PUE (Rules for Electrical Installation), then for the neutral wire should be used blue, and for the protective. yellow-green. If these clues are not available, you need to mark all the cores of the cable yourself.
  • Once you have the socket in your hands, carefully inspect all parts of it. The presence of any visual defects is a strong argument for the purchase of a new product. Serious cause for concern is not unless the presence of a small burnt spot in the contact part, which you can remove yourself ordinary skin.

What to do and how to move the socket to another place: 4 options

Any relocation begins with the installation of new junction box, dismantling the old socket and the line of its power from the junction box. When performing this action, it is important not to damage the entire apartment system.

Begin the transfer of the socket of the electric stove should be started with the removal of voltage in the network to be worked with. Pay attention even to the possibility of accidental touches, they can be very dangerous.

Usually make a separate switch in the switchboard for the electric stove. Still, it is highly recommended to check the power point with a two-pole voltage indicator.

The course of work on the dismantling looks approximately as follows:

  • After removing the old socket, it is important to check whether all its wires are intact, especially if you own a power point with a voltage of 380 V.
  • To make the stove work correctly, pay special attention to the order of connection of the phase, neutral and protective wires, because it is their wrong connection that can lead to a short circuit.
  • If the original wiring was based on PUE (Electrical Installation Regulations), then the neutral wire should be blue and the protective wire should be yellow-green. If these hints are missing, you need to label all the cores of the cable yourself.

Author

Laidred

| Denial of responsibility | Contacts |RSS