Home Article How to make electric
Article

How to make electric

Homemade meat grinder

You have a regular meat grinder at home, but there is no strength to use it. When the knives are dull, the twisting of meat with veins in the minced meat resembles a real arm wrestling. Plus a problem.There is nowhere to buy an electric meat grinder. Then this is an article for you. We will write how to create a home.made meat grinder with your own hands, t. e. From manual to automatic.

Sharp the installation frame from a metal corner (45 x 45 mm), which consists of 4 legs and 4 jumpers: 2 at the top and 2 in the middle.

Put the countertop of 3 boards on top (thickness. at least 300 mm).

Screw the legs from both ends to the jumpers using bolts.

Installation frame of a home.made meat grinder

Connect the second and third boards together. And leave the gap (from 30 to 40 mm) between them and the first for the belt.

Instead of a pen, put a hub on a regular meat grinder. On it, put a pulley with a diameter of. 200 mm and which after. fasten 2 bolts. You can use a pulley from a car generator only more diameter.

“How the meat grinder works”?. The answer to this question is contained in the article of the same name on our website

How to sharpen a knife meat grinder? Read about the three most proven ways on our website

make, electric

Attach a meat grinder to the countertop with your own clamp. For this:

From the side of the gap in the front board, make a rectangular neckline and recess: 5-7 mm under the legs (2) of a home.made meat grinder (photo below).

Put a pulley with a diameter of 70 mm on the shaft.

At the bottom, set the drive (three.phase electric motor) on the plywood sheet (thickness. 12 mm) and fix it with 4 bolts.

Run the engine and stop it with a switch in the form of a button.

For insurance, you can create a tin or plastic casing on the drive. a pulley with a belt. When cooking minced meat, jelly or tomato paste, place them in small portions and push them with a pusher.

How a home-made meat grinder is created, you can watch a video instruction here:

How to assemble an electric barricure correctly

Consultant in a furniture store. Work experience 5 years.

Assembling an electric yas.grinder is no more difficult than a manual copy. Detailed instructions, often illustrated, are in the user guide for each specific device. In general, the assembly procedure for the device is such.

    First you need to insert a screw into the nest on the engine housing. After fix it by turning counterclockwise so that the part snaps. This guarantees the correct operation of the mechanism, the transfer of effort.

Rush coupling electric meat grinder

There is no handle in an electric meat grinder. Instead of a lever is an engine. Before collecting meat grinders, pack the gear clutch. By the way, most of the breakdowns falls on the specified part. Designers protect the product from mechanical overload with two methods:

  • Gears are made of plastic, when the shaft is jammed, the coupling breaks. Remember this, do not allow such situations.
  • Advanced domestic manufacturers instead of plastic gears supply meat grinders with special bushings. Details serve to protect. Now the bushings are already breaking during overload. Plus a method: if there can be two gears in the kit, then miniature inserts are shipped with dozen, which sharply reduces the frequency of the need to contact the service center.

Inside the gearbox are reducing gears. One, usually steel, with a small number of teeth, modest diameter, is planted motionless. Without special devices, it will only be possible to separate the assembly in a vice. It is recommended to first warm up the details. Look at the video (YouTube to help). For heating, for example, a soldering iron is used, make sure that the engine rotor does not burn out. The winding is designed for a certain temperature (for example, 135 degrees Celsius), with the heating of the collector block, there is a chance to burn the wires.

So, lowering gears of two or more. The coefficient is calculated by the number of teeth of the driven and leading. For example, on the shaft is about 10, and on the outer ring of the first stage of the gearbox for 25. As a result, each subsequent gear spins more slowly, the lowest speed of the screw leading in the movement.

Explain the reason. Engine power of the meat grinder. fixed value. This is done so that the windings can disperse the released heat determined by three values:

The more massive the engine, the greater the surface area, the more significant power of the scatter. At the same time, performance depends on consumption. As you know, three values ​​are interconnected:

Productivity depends on the first meaning, but for hard meat you have to attach more effort. Two values ​​are inversely proportional to each other. Both increase with an increase in power. The manufacturer tries to work for a longer the meat grinder (it will be necessary to reduce consumption, otherwise the windings will be quickly overheated), and at the same time the ground is all in a row (it is necessary to increase the torque), it gave out a lot per minute (increasing the speed). In order to eat a fish and do not choke on a bone, we will pay more, and the torque increases easily. lowering the steps of the gearbox.

Each gear sits on a separate shaft. When assembling, the place will need to be lubricated with lithol or silicone composition like PMS 1000. Previously, the details of the gearbox are cleaned by a rag of dirt. This includes the old lubricant. The reducer of the meat grinder is assembled in the process of reverse disassembly. Before dismantling, it is recommended to photograph each block so as not to forget what is being put. Each gear is worn neatly, then we unit the mechanism with the hand (with the power turned off, of course). Please note what force you have to apply at the level of the screw. The reducer reducer is set to increase the torque of the meat grinder.

Each gear is evaluated for wear. Even specially designed to protect against overload. The main parameters when choosing third.party spare parts are the number of teeth of a small and large ring, diameter, thickness, landing hole. We believe that the manufacturer is unprofitable to constantly reconfigure the conveyor, even on an old meat grinder, it is possible to find spare parts.

Powerful homemade meat grinder-meller for 750 watts

Hello everyone, I propose to consider a powerful meat grinder based on an asynchronous engine from a pump for 750 watts. Such

Not only capable of grinding meat with veins, but also on it you can hammer grain, corn, horseradish (plant roots) and much more. In the assembly, homemade is quite simple, the motor is suspended articulated, the contents of the container are poured by tilting the engine 90 degrees. The chosen engine is quite tenacious, it will easily cope with the tasks, and will not even be particularly warming up. If the project interested you, I propose to study it in more detail!

Materials and tools used by the author:

List of materials:. asynchronous engine from the pump 750 watts;. a pot of suitable diameter (better steel or stainless steel);. sheet steel for a knife;. corner;. steel plates;. bolts and nuts;. cable with good isolation;. switch;. Block of paint.

Step one. Preparation of the motor first thing we analyze the old pump, remove all the excess, this applies to the impeller. There is also an oil seal on the motor shaft, it must be replaced with a new one to protect the motor from harmful liquids.

Further, the author armed himself with a corner grinder and cut off the excess part of the case, as a result we got a long axis of an uneven diameter. To level the axis, the author launched the motor and with the help of a corner grinder removed excess metal, we grind the diameter of the axis under the diameter of the drill, which we will drill a hole in the case of the meat grinder.

Step two. Making a case for a meat grinder

Read more: 42 interesting films about viruses, pandemia, infections, epidemics and zombies. A lot of zombies!

We make a case for a meat grinder, for this we need a pot of suitable diameter. If you think to use a machine as a grain mill, we take a steel pan, aluminum will not live for so long.

We drill a hole in the center of the bottom of the pan, the shaft must enter the hole with a minimum possible gap.

We also drill holes for fasteners and securely fix the pan with screws with nuts. So that water does not pass through the hats of the screws, you can make rubber or even paper gaskets under them.

We make a simple knife for a meat grinder, use good steel, you can make a knife for a meat grinder from a suitable kitchen knife. The knife has a square hole, the engine shaft is also dragged under a tetrahedral. To fix the knife, the author welded a piece of a threaded rod to the motor shaft, we fasten the knife with a nut. So that everything can be disassembled with your hands, you can weld a steel wire hand to the nut.

As an experiment, the author flooded water into the car container. Water does not seep anywhere, which means that the motor does not threaten the motor, the remaining microcracks will immediately be walled up when using the meat grinder first.

If the water proceeds, you need to solve the problem, otherwise you will be beaten by electric shock, and the motor will not last long.

We make a simple frame for the engine, the motor will hang articulated, which will make it possible to turn it to devastate the capacity. Of course, you need to fix the motor somewhere in the center so that you do not need to spend a lot of effort on lifting a heavy motor.

We paint all the parts of the car so that the wife is not afraid of homemade, we collect everything, put a reliable roof in an accessible place. Of course, it would be nice to turn on such a motor using ground, it will protect you from a shock in the event of a breakdown of insulation or wetting of a motor.

For demonstrating work, the meat was quickly and excellently varied. After work, pour water into the tank, unscrew the nut with one hand and remove the knife. Everything is easy to wash, pour dirty water.

The car turned out useful and necessary on the farm. I hope you liked the project, and you have found useful thoughts for yourself. Good luck and creative inspiration, if you decide to repeat this. Do not forget to share your ideas and homemade ones with us!

Become the author of the site, publish your own articles, descriptions of self.proceeds with payment for text.

Classification of an electromyas.rh

Modern industry produces electromyubs of two types: this is:

Skin

Figure 4. screw meat grinder: 1.nut 8-landing groove 9-horses, 2- small grill 9-horses 10 pusher, 3-large grille 10 pusher 11-sized, 4-grille for beef strogans 11-p 7-shneck

Kutter

Figure 6-Kutter meat grinder: 1-fixer 6-tip inclusion, 2-knife 7-horses, 3-lid 8-electricalodist, 4-Stacan 9-line.power, 5-blocking device 10-do, 11-fees screws

How to disassemble electric meat grinders of different manufacturers

A meat grinder is a device that is present in the kitchen of any housewife. Its purpose is food processing. Hand models are not relevant for a long time, now electrical equipment is now used, which is more powerful. For durable use, it is important to properly assemble and analyze an electric meat grinder.

The device of an electric meat grinder

Before moving to the device, the advantages of this product should be identified:

  • Great power. She is able to grind a large number of products in the shortest time.
  • For modern models, hard fixation does not need, it can calmly be located on the table in any place convenient for the hostess.
  • The modern device is safe to use. Products enter it through a narrow neck with a special pusher.

To learn how to use this device, it is recommended to familiarize yourself with its design. In disassembled form, it looks as follows:

  • Plastic or metal case.
  • Electric motor, which is located inside the device.
  • Meat receiver equipped with a grocery.
  • Pusher made of plastic.
  • Schnek shaft.
  • Knives. There are usually several nozzles in the kit.
  • Gratings, there are also several of them, for large and fine shinkling.
  • Fixing cover.

Some models have additional details, but the above are the main and mandatory elements that are included in the set of this technique.

Operation Rules

Currently, there are a huge number of companies that are engaged in the production of a meat grinder, among them: Moulinex, Cameron, Delfa, Zelmer, Kambrook and others. But the operating rules for all are the same. In order for the device to serve the following rules for a long time:

  • Before turning on the device, you must make sure that it is properly assembled and all the elements are securely fixed in their places.
  • Ensure strong fastening of the working part to the support.
  • Before use, ground the device.
  • Make sure that the knives fit tightly to the grille. This will provide better grinding.
  • Pre.chop foods and load them in small portions.
  • After each use, it is necessary to thoroughly wash and dry the cutting objects.

You can use the kitchen technique only for its intended purpose

You cannot turn on an electric meat grinder without any products in it.

Causes of problems and methods of elimination

If the device still breaks, you will have to carry out a whole range of measures to repair it. To quickly eliminate the malfunction, you will need to diagnose the device.

At first, a visual inspection is carried out. If he did not bring any results, then the reason lies in the structure of the structure. Perhaps there was a clogging of lubrication or overstar.

Advice! It is necessary to immediately eliminate the cause of the breakdown, and not wait for the mechanism to completely fail. In the latter case, returning the equipment to working condition becomes a rather difficult task.

There are such reasons for the breakdown, for the elimination of which the kitchen equipment has to be disassembled. Here is one of them. bearings provide rotation of the entire mechanism, respectively, they are most susceptible to wear. The fact that the part was out of order is evidenced by the appearance of severe noise when the device is turned on. In order to eliminate the malfunction, you will have to disassemble the meat grinder.

  • Remove the plugs that are on the back wall of the plastic case.
  • Turn the product over.
  • Unscrew the screws that fix the bottom of the mechanical device to the body.
  • Remove the front damper.
  • Unscrew the board from the metal case with a cross.
  • Get the bearing and change it to a new.
  • Collect the unit using this instruction in the opposite direction.

How to disassemble a meat grinder and clean it

Mostly housewives keep it assembled, explaining this with convenience. But in any case, after operation, the meat grinder will have to be disassembled, thoroughly washed and dried. It understands quite simply, while some additional tools will not be needed.

  • A removable meat receiver is extracted from the neck.
  • Next, you will have to unscrew the nut that fixes the design. She unscrews counterclockwise. Sometimes the nut is very tightly screwed, in this case you can use the dry towel and the task will be easier.
  • A lattice and knife are removed from the shaft.

All parts of the device should be thoroughly washed and dried. Only after that you can assemble it and put it in the closet

There are currently a large number of models. In this case, each of them has various power. It all depends on the grinding of which products and in what quantity it is purchased.

There are models with a capacity of 200-800 watts, they are also called “babies”. They will cope with meat if it is without a single vein. Mostly housewives buy more powerful. from 1000 to 1600 watts. With the help of such a technique, you can process 2 kg of any meat in just one minute. She copes with large pieces and even small bones.

What can be done from the old meat grinder: ideas for alterations

New technologies appear in the market with a rapid speed. Many household products lose demand among customers.

How To Make A Electric Generator Model | Generator Model Science Project| Mini Generator | Generator

Therefore, hand.made meat grinders almost exhausted their relevance in the kitchen, but got a new application in the field of decor.

The same applies to electric products that have failed. They are used to create new devices necessary in the economic sphere.

Important! People’s craftsmen proved that it is not necessary to throw the product. He can always find another application.

We will tell you what to do from the old meat grinder.

Ideas for using a hand meat grinder

In the modern world, the electromyus.grinders practically displaced mechanical. The traditional in the past, the kitchen device gradually migrates from home treels to a garbage chute. However, using a little imagination and creative skills, the old meat grinder can be turned into a unique vintage item of interior decoration.

Kashpo

Lovers of home plants will appreciate the original flower pot.

To do this, just fix the meat grinder on the windowsill, and fill the ground into the body.

Lamp

The original lamp will attract guests. Or the base of the base of the light is used both the case of the product and the basis of the mounting clamp. And lovers of special comfort use the device as a candlestick, placing a candle inside the case.

Holder

In the farm, the old meat grinder can be tried on as a holder for towels or toilet paper. A suitable stalk is placed in the case instead of spare parts, the meat grinder itself is attached to the surface.

For needlewomen

The use of the kitchen device also found in the sectors of the office and needlework. In the case you can place items for writing or a puffy needle.

Interior decoration

Craftsmen use the case of the meat grinder and its component of creating original installations that adorn the interior.

Using internal components

You can use not only the case in everyday life. Internal and external components that are in a meat grinder can also be used in the household or decorating.

Lattice

The lattice is suitable for the manufacture of potatoes. The grate must be carefully sanded with sandpaper. A hairpin is inserted into the central hole, which serves as a handle and is attached with bolts. The upper part is recommended to equip a silicone insert for more comfortable use and safe contact with the skin.

Pen

Handles from the old meat grinder can be used to create hooks for clothes

Such a product looks very original and creatively.

Useful products from an electric meat grinder

Not only a mechanical product received its use on the farm. The broken electric tank is also useful to prepare new devices from it. A working engine will help in the creation of many household and household appliances.

Fan

Having attached the blades and mounts, you can get a small room fan. Thus, the owner saves to buy a new device and finds use for a broken electrical device. After all, the fan is a healthy household appliance in hot weather. And also he will become an indispensable assistant for every mistress engaged in cooking.

Sander

For men on the farm, an abrasive mini-station or a grinding machine will come in handy. They are also collected using the engine. In everyday life, such products are used to sharpen metal products: axes, knives, disks. Specialized stores offer a wide selection of such products. However, it has a high price. Therefore, the independent assembly from the components of the Philips of the Electric Power Greek or other models will significantly save the budget and will like lovers of technology.

Important! The assembly processes of electrical devices must be carried out in strict accordance with safety precautions. Non.compliance with the rules can lead to injuries.

Old things often gain a new life. Even such ordinary kitchen items as a manual or electric meat grinder can become a harmonious and original item of interior. The main thing is to apply a little creativity and use the small part of the free time.

How to disassemble electric meat grinders of different manufacturers

A meat grinder is a device that is present in the kitchen of any housewife. Its purpose is food processing. Hand models are not relevant for a long time, now electrical equipment is now used, which is more powerful. For durable use, it is important to properly assemble and analyze an electric meat grinder.

The device of an electric meat grinder

Before moving to the device, the advantages of this product should be identified:

  • Great power. She is able to grind a large number of products in the shortest time.
  • For modern models, hard fixation does not need, it can calmly be located on the table in any place convenient for the hostess.
  • The modern device is safe to use. Products enter it through a narrow neck with a special pusher.

To learn how to use this device, it is recommended to familiarize yourself with its design. In disassembled form, it looks as follows:

  • Plastic or metal case.
  • Electric motor, which is located inside the device.
  • Meat receiver equipped with a grocery.
  • Pusher made of plastic.
  • Schnek shaft.
  • Knives. There are usually several nozzles in the kit.
  • Gratings, there are also several of them, for large and fine shinkling.
  • Fixing cover.

Some models have additional details, but the above are the main and mandatory elements that are included in the set of this technique.

Operation Rules

Currently, there are a huge number of companies that are engaged in the production of a meat grinder, among them: Moulinex, Cameron, Delfa, Zelmer, Kambrook and others. But the operating rules for all are the same. In order for the device to serve the following rules for a long time:

  • Before turning on the device, you must make sure that it is properly assembled and all the elements are securely fixed in their places.
  • Ensure strong fastening of the working part to the support.
  • Before use, ground the device.
  • Make sure that the knives fit tightly to the grille. This will provide better grinding.
  • Pre.chop foods and load them in small portions.
  • After each use, it is necessary to thoroughly wash and dry the cutting objects.

You can use the kitchen technique only for its intended purpose

You cannot turn on an electric meat grinder without any products in it.

Causes of problems and methods of elimination

If the device still breaks, you will have to carry out a whole range of measures to repair it. To quickly eliminate the malfunction, you will need to diagnose the device.

At first, a visual inspection is carried out. If he did not bring any results, then the reason lies in the structure of the structure. Perhaps there was a clogging of lubrication or overstar.

Advice! It is necessary to immediately eliminate the cause of the breakdown, and not wait for the mechanism to completely fail. In the latter case, returning the equipment to working condition becomes a rather difficult task.

DIY Amazing Kitchen Appliance Electric Peeler

There are such reasons for the breakdown, for the elimination of which the kitchen equipment has to be disassembled. Here is one of them. bearings provide rotation of the entire mechanism, respectively, they are most susceptible to wear. The fact that the part was out of order is evidenced by the appearance of severe noise when the device is turned on. In order to eliminate the malfunction, you will have to disassemble the meat grinder.

  • Remove the plugs that are on the back wall of the plastic case.
  • Turn the product over.
  • Unscrew the screws that fix the bottom of the mechanical device to the body.
  • Remove the front damper.
  • Unscrew the board from the metal case with a cross.
  • Get the bearing and change it to a new.
  • Collect the unit using this instruction in the opposite direction.

How to disassemble a meat grinder and clean it

Mostly housewives keep it assembled, explaining this with convenience. But in any case, after operation, the meat grinder will have to be disassembled, thoroughly washed and dried. It understands quite simply, while some additional tools will not be needed.

  • A removable meat receiver is extracted from the neck.
  • Next, you will have to unscrew the nut that fixes the design. She unscrews counterclockwise. Sometimes the nut is very tightly screwed, in this case you can use the dry towel and the task will be easier.
  • A lattice and knife are removed from the shaft.

All parts of the device should be thoroughly washed and dried. Only after that you can assemble it and put it in the closet

There are currently a large number of models. In this case, each of them has various power. It all depends on the grinding of which products and in what quantity it is purchased.

Electromyas.grinder from an ordinary hand meat grinder

Good day, lovers to squeeze with their own hands fit and useful homemade. In today’s article, we will consider in detail how to fulfill the dream of a large number of Soviet schoolchildren (and not only). Many people remember, and someone still uses the good old manual meat grinder. This is probably one of the most reliable kitchen instruments, which is probably eternal and is inherited. Surely those who used them dreamed of automating this process, but before there was no way for this, but now factory electric meat grinders have already appeared, and the idea to automate their old meat grinder has forgotten. So in this article we will collect an electric meat grinder from an old manual meat grinder, and we will do it as much as possible. Well, well, I think you should not pull with a long preface, they drove.

You can find links to some design components at the end of the article.

To remake the old hand meat in the electrical, you will need the following:

As already mentioned, we will collect an electric meat grinder from an ordinary manual meat grinder attached to the table. If suddenly you did not have such an old meat grinder at home, then in principle you should not worry, since such a new meat grinder is very inexpensive and is sold in almost every grocery supermarket. We unscrew the handle from the meat grinder you take, it will no longer be needed.

In order to connect the drive from the electric motor to a meat grinder, all these components must be fixed on one base. We will use a small piece of plywood or plank as the base. Wood is very simple and easy to process material with which it is very convenient to work. But this material has a great drawback for our goals, it is a fear of moisture and water itself, so I recommend walking along this board with some protective varnish.

We have a meat grinder in the corner of the plank, as it is depicted below. This is all necessary for us to have a place to install other components. Marker mark the places for fastening a meat grinder on a plank. Then we remove the meat grinder and draw through holes in the marked places in the marked places. Then again we return the meat grinder to its place and already fix it there using screws, nuts and washers. Tighten the nuts with moderate force.

For the next step, you will need a collector electric motor. The electric motor is not quite simple, but with a lowering gearbox, and preferably with metal gears. There is still a large load on the meat grinder, and the reduction between the driven and the lead gear will not be enough. We put on the drive gear of the belt drive to the shaft of the electric motor gearbox and move on.

Now it is necessary to ensure the transfer of torque from the led gear to the meat grinder. And in fact, there is actually nothing complicated here, it is simply necessary to choose a bolt on the thread and size, which can be screwed into place of the old handle. This bolt must be screwed into place the handles through such a spacer as a driven gear. In order for the driven gear not to scroll, there is a special hole under the screw in it, so to use it, it is necessary to slightly work out the bolt with a file (see. a photo)

We insert the bolt into the driven gear and fix it, there we tighten the locking screw on the driven gear. We screw the bolt with a gear to the place of the old handle. Next, in order to understand where to install the electric motor, or rather to the motor.

It is necessary to naturally temporarily attach a belt to the driven gear. And approximately attach an electric motor (with a motorema) to the plank, putting a belt on the lead gear. In the place where the belt stands exactly perpendicular to both gears, we put the marks under the mounting holes of the motor.

Author

Laidred

| Denial of responsibility | Contacts |RSS