Home Small appliances How to make a loop on a janome machine
Small appliances

How to make a loop on a janome machine

Button loop on the sewing machine Janome

Who sews clothes with their own hands knows that the overall appearance of the product largely depends on how sewing loops for buttons look like. It is the blotting of the loop that is considered the most responsible operation, which is most often impossible to redo “without traces”. Therefore, before making a loop on a sewing machine, especially in the “automatic” mode, be sure to try to perform a trial loop for a button on a piece of fabric, which also has the number of fabric stages and cool materials.

In this article, we will give you some useful tips on how to make loops on a sewing machine in a machine gun with a special paw, and in mode a semiautomatic device with an ordinary paw for a line of zigzag.

It is easier to sweep away the loops on dense woolen fabrics, since the machine promotes the fabric well in both directions, without any problems. But when the fabric is very thin and delicate, the small step of the zigzag line can “slip”, and an incorrectly tuned rail (cloves) can tighten the fabric under the paw. In both cases, the sewing loop will have to be redone and most often with the consequences, in the form of fabric punctures, and sometimes its gusts.

Therefore, first setting up a sewing machine. Adjust the tension of the upper and lower thread. Adjust the height of the rack rise (if there is such an adjustment). Check the degree of pressure of the fabric paw. In order for the fabric to move confidently under the paw, it should be well pressed against the cloves. Cloves, however, lift high for thin fabrics, you can’t light the fabric otherwise.

Do not forget to remove a special lever to the paw, automatically switching the operating mode of the machine. Those sewing machines that have such a paw as in this photo must have a lever to perform a loop automatic.

Loop on a typewriter semiautomatic device

Inspect the body of your machine and find the image of the loop. As you can guess in the image, the loop on this type of typewriter is performed in four steps. You can also adjust the frequency of the loop in the settings. The closer to zero the regulator is turned, the closer the stitches will be located to each other. You can experiment and choose the frequency that you like best.

  • The first operation is the left line of the loop
  • Second operation. Sociable line from below
  • The third operation. The line goes up
  • Fourth. Sociable line on top.

There is usually a special convenient paw for a loop to the typewriter. There are marks on it that allow you to select the desired size of the loop, and the arrow that will allow you to finish in time. The length of the loop is usually three to five millimeters larger than the button. We apply a button with the widest part to the arrow and measure it to what mark the line should reach.

To change the foot, use the lever located behind. The marks should be closer to you, otherwise the needle will rest against the plate and the line will not work. Passing the thread under the paw and pointing it back, fix the paw for the loops. Now you can start work.

An important advice: before making a loop on the product, practice on samples, and their thickness should be exactly the same as that of the finished product. Loops are usually made on the folded fabric. Do not forget that such details as belts, collars, cuffs, strips are usually compacted with adhesive materials. non.woven or understudy. Accordingly, to prepare a sample, you need to glue the non.woven and bend the fabric by the iron.

Next, you should make markings for the loop. If this is a belt, as we usually have 1-1.5 cm from the edge. Mark the length of the loop and outline the hole clearly in the center of the belt. Before starting work, check the settings of the machine: the frequency of the stitch and the operation of the loop. Lower your foot so that the marking passes exactly in the middle, and start making a line, helping the machine with your hands. Raise the needle so that it does not remain in the fabric, and turn on the next operation. Having made three or four stitches, you can proceed to the third operation. The fourth operation fix our loop with two or three stitches on top.

It is not recommended to cut the remaining tails, because the line may begin to bloom. You can tuck the threads into the usual sewing needle and let them on the other side and knit them and the wrong strings into the knots, and then cut to 5 mm. Then you can “seal” the tails, scorching them with a lighter.

It remains to carefully make a hole with the opener, and the loop is ready! Put the loop from the edge to the middle without touching the threads, and then repeat this action on the other side of the loop. Extra threads that appeared in the center can be cut so that there are no tights.If the material is dark and does not really melt, you can also slightly plow it with a lighter from the back.

There is another way to hide the tails: for this, they must also be pulled to the wrong side, align it, then place the needle in the material inside the fixed seam, between the layers, insert the tails into the needle and pull it inside, between the layers of the fabric. This method is suitable only for opaque fabrics.

How to make a button loop on the sewing machine Janome?

In a special paw for loop automath, there is a jacket for a button. With the help of a plastic lever sticking out on the side, open the nest and place a button in it. Fix the button with the same lever so that the machine can correctly determine its diameter. You can not lay in the foot of the button that you will sew (and the buttons in the form of a “mushroom” will not be fixed there), but it must be a button of the same diameter as the one that you will sew to the product.

Install a paw for loop on a sewing machine. The button should be in it until the end of the work. Both working threads (upper and lower) are removed under the paw and directed to the left.

Install the values ​​shown in the photo on the typewriter. In a line with different seams, select the very first meaning under which it is written “VN”.

Set the size of the stitch at level 5 (according to the rules, this value can range from 4 to 6), and the length of the stitches. between 0 and 1.

From the upper left side of the machine, lower down to the Stopper paw. a metal stick with a plastic tip. Having lowered it down to the stop, move towards yourself. then Stopper will take it to the plastic paw of the paw. This stopper will stop the loop processing when the machine sees the entire loop in a circle.

Important: before the manufacture of the first loop (as well as between the loops, if you need not one), scroll the flywheel of the machine located on the right side of the case, one click forward (from yourself), and then one click back (to yourself). This will set up a machine at the beginning of the manufacture of a new loop. Next, put a trial piece of fabric under the foot and just press the car pedal. She herself sews the shape of the loop, based on the size of the embedded button.

Try to sew the loops on the “draft” using different width values ​​(from 4 to 6). Having chosen the most suitable option, proceed to the manufacture of the loop on the prepared part of the product.

Put the trouser belt under the foot and in the right place, drive out the outlines of the loop. The machine sews a loop in a circle: first the front narrow crossbar, then the left side, distant cross member and the right side.

Remove the ends of the threads to the wrong side of the product and tie it in order to tightly fix them.

It remains only to cut the loop outlined by the machine! Do this very simple with the help of a opener. But the problem is that this tool is very sharp, which means that it can be expelled excess. So that the opener does not cut the line of the loop edging, limit the loop with a tailor pin, stuck it, as shown in the photo.

Cut the loop with the opener towards the limiter from the pin.

Check if your button passes into a made loop. If the hole is still small, cut it with the opener a little further.

Even a novice seamstress can make a button on a button on a Janome machine, because the process of edging the loop of the desired size occurs automatically! The main thing is not to forget before this operation to lower and press the stopper to the paw: without this, the machine will make the base loop of the minimum size, which is unlikely to fit your button.

How to perform loops on a sewing machine without special devices. Master Class

Great gratitude to the author: Daria Tabatchova. Further words and photos of the author:

Most of modern sewing machines are equipped with the function of processing loops in an automatic or semi.automatic mode. But what if your household sewing machine does not support this function?

There is a very simple way with which you will learn how to perform loops on a sewing machine without a special function and paw to wash the loops. In this master class, we will talk about this.

Most often, the loops on the fastener are processed at the last moment, when the entire product is almost ready. It is important to remember that the location of the loops must be duplicated, for example, using adhesive oak. It is advisable to choose a non.contrast color relative to the color of the product of the product.

You will need:. Portnovsky pins for medium fabrics;. Portnovsky pins for thin fabrics;. small scissors;. ruler;. A disappearing fabric with a thin line.

Determine the width of future loops. The loop is usually made several millimeters longer than the diameter of the button.

The diameter of the buttons is 2.7 cm, the selected loop width is 3.0 cm.

Mark the position of all loops at the site of the future fastener. Using a washed marker, draw a loop frame 3.0 cm long and about 0.5 cm wide.

If there is no thin marker, the frame can be marked using the marking stitches.

Layers of fabric in the fastener are replaced or knitting with tailor pins.

make, loop, janome, machine

Placement for thin fabrics on the frame of the loop, in them along the short sides, this will ensure convenience and accuracy when processing the loop frame on the sewing machine.

This operation is performed on a sewing machine.

Settings: straight line, 1.5 mm long stitch.

By marking, remove the frame with a line with a short stitch: the length of the line on the long sides of the loop frame is limited by pins, it is better to count the number of stitches in the area of ​​the short sides of the loop, it should be the same on all the short sides of all the loops, so the accuracy of the loops will be provided as much as possible.

The frame of the loop. Pins located on the short sides of the loop frame at this stage is better not to remove.

At this stage, the long sides of the loops are processed with a dense zigzag.

Settings: Sigzag line, stitch length ~ 2.5 mm, zigzag density ~ 0.4 mm.

The zigzag must be laid along the long side of the loop so that the stitches lie down on the two sides of the laid line forming the loop frame. Landfires in length. pins.

At this stage, a loop frame closes. short sides are processed with a dense zigzag.

Settings: Sigzag line, stitch length ~ 6.0 mm, zigzag density is minimal ~ 0.2 mm.

On a test sample, it is better to first choose the length of the stitch for processing the short edge of the loop. The stitch should close the loop in width. The paw of the machine is located exactly in the center of the loop, and the short side is clearly under the needle.

To close the loop on the width, you need to make about 10 stitches back and forth, performing point fixes at the beginning and at the end of the operation.

The frame of the loop is shameful, you can remove all the pins and a trim.

The area of ​​the hinges is inituted.

It remains only to cut the loops. This operation is convenient to perform with small and sharp scissors. It is very important when teething not to hurt the zigzag threads.

Gently cut the extra thread inside the loop, caring their excess.

Ready!

How easy and sorry to sew a button on the leg

In order to make it more convenient to sew a button, forming a small “leg”, you can use a needle for a sewing machine: place a thick part of the needle under the button, and drive sharp into the fabric.

So under the button, the space required to form the “legs” will be created, and the needle will not have to be held, t.to. She holds onto the fabric herself.

make, loop, janome, machine

Strike loops

These loops are difficult to perform. But there is a little trick that will help to facilitate the work of a tailor. So that the fabric does not fall and is precisely marked, it is necessary to use masking tape.

How to make buttons for buttons manually: step.by.step instructions of a sharp loop:

  • It is necessary to determine how long the loop will be. To do this, use data on the diameter and thickness of the button, add 3-6 mm here. The width of the loop itself is 6 mm. We draw a loop on millimeter paper, laying thin plastic and gluing it with tape. For each of the loops, you need to make a workpiece of adhesive tape.
  • Along the finished framework, we carefully pass the seam with a length of the stitches of 1 mm. Also, for each individual loop, you need to prepare your stool with a width of 6.5 mm. We pinch with English pins to the front side of the side, to where the loop is planned. Now you need to lay two parallel seams from the wrong side, which will definitely match the facial. The beginning and end of all seams are exclusively in the corners.
  • Gently cut through the sharpener first, and then the side itself and turn the edges of the stool on the wrong side. We sew all the edges with fixed lines.
  • We take the selection to the side, completely pierce the layers with pins. Gently and accurately glue the tape to the outlined part and sew. Tape can be removed, the loop is ready.

It should be noted that such loops are used, as a rule, in the process of manufacturing outer thick clothes like a coat.

We learned the basis of how to make loops for buttons manually. But sewing is a creative process. And the fantasy here is far from the last place. It’s especially great to think and work on how to make a real decoration of the whole thing out of fasteners, and, of course, then proudly wear this original product.

Every woman needs to be a little sample. It is not necessary to be able to cut and sew complex things. It is important to have basic skills that will come in handy in everyday life. One of these is to sew a button. But it always needs to be fastened for something, so learning to make a loop from threads is extremely important and useful. The loop is used as a fastener, as a suspension for a towel or curtains, as well as as a decor of clothing and interior items.

Materials and tools for loop processing

If you have never made loops before, then do not rush to try on ready.made details of clothes. Take the usual segment of the fabric for starters and practice making the loops on it. It is best to practice on fabrics of different densities.

Types of automatic loops

Let’s look at various options for slotted loops, and find out their purpose.

make, loop, janome, machine

Simple rectangular loop

This loop is often called linen. The product is located vertically. This option is found mainly on shirts, linen and home clothes. Some cars offer two options for this operation:

The version of a rectangular loop in the form of “handmade imitation” may also be offered.

Loop with one rounded end

A loop for thin and medium.dense materials, which allows you to place a button more even, since it is reliably fixed by a semicircular recess.

Clothing with such loops is easier to unfasten.

They are located on the product horizontally and are usually used on blouses and children’s clothing. Can be offered in two versions:

Loop with two rounded ends

It is used on a coat and jackets, clothes made of dense and medium.dense materials.

The two ends of the loops are rounded when placed under the stitches of the cord or finishing thread.

Some machines offer options with enhanced fixtures and a variety of this loop “with handmade imitation”, which is suitable for knitwear.

The loop with the eye

It is also used in outerwear with thickened processing and is located horizontally.

Such a loop is made for buttons with a volumetric leg. Can be made with reinforced point or transverse fixing.

Loop with one line and elastic

The circuit loop with the tank of the contour is designed to fasten the cuts of s, strengthen loops, for working with the skin. The elastic loop has a rectangular shape and can be used for both elastic materials and for decorative purposes.

Decorative loops

These operations include various forms of loops, including with an eye, which are suitable for dense inelastic fabrics and medium knitwear.

Eyes

Operation for processing holes for a cord or braid, for decorative finishes. After processing, the hole is cut out by an awl or a hole pile. Maybe in two versions:

Horizontal and vertical loops

The most practical are horizontal loops. Such a loop when tensioning the fabric is practically not deformed, and buttons do not jump out of it. They are placed exactly perpendicular to the edge of the product. Vertical loops are mainly made on compacted edges of products, for example, on shirts or blouses. And as the name implies, they are placed parallel to the edge of the product. Since such loops are subject to deformation, they are located closer to each other (increase their number) and use small buttons for them.

The loop is processed using one special paw into one pass.

To give the loop of relief under the continuous line “zigzag” a thin cord is placed.

It is processed by two kants. They are tired on the front side of the loop, then the free ends of Kant are extended through the incision on the wrong side.

A thin cord is invested in the edges for processing the loop.

It is treated with strips of fabric, configured on the front side and turned out to the wrong side.

On the skin or suede, it is treated with a straight line around the cut.

Is an unfinished section of the seam. Sometimes treated with a straight line from above.

How to make a buttons for buttons on a knitting bar with your hands

Loop design. How to make and fix the loop manually.

Places for loops are determined, and we begin to create them on an even (connected) place. The loop should be located in the middle of the bar. In this case, 5 loops are enough for us. Here of these 5 loops, we cut only the middle loop

We begin to pull out this trimmed loop, neatly, in the ear.

We get two tails and a hole in the middle.

We hide the tails in different directions. We stretch (hide) them in the bar.

The bar is connected by the interweaving of reps or a closed sash (elongated loop)

How to fix the broken stitches of JUKI-HI Speed Sewing Machine [ TAGALOG VERSION ]. Full Tutorial

And in this interweaving, all ends can be carefully hidden in the cloth of the bar.

There was one hole left. Now we will turn it into a loop.

Take a thread, fold in half to form a loop.

First, 2-3 stitches, fix the vertical column.

Then, with a kettle seam, we fix the open loops.

make, loop, janome, machine

Again 2-3 stitches, this is a fixing of the second vertical column.

And we fix the last open loops with a kettle suture.

We fix the thread that we worked and hide its ends in the bar.

Here is a button, and here is a loop.

So that the loop does not stretch during operation,

Its size should be slightly smaller than the diameter of the button itself.

How to sew buttons?

Buttons on the outcome of the bar are sewn not exactly in the center, but slightly moving from the center, towards the side seam, approximately 0.5 cm. Then, in a fastened form, the bar is covered with each other. I shared with you a simple, but reliable and trusted year in practice, a way of making horizontal loops for buttons, on a bar, which is connected on a knitting machine.

I am performing on a sewing machine. The loops made on a sewing machine behave wonderful and it takes much less time to manufacture. Watch a video lesson how to make vertical loops on a sewing machine.

The bar is connected on two fonts with a reinforcement of reps (closed sash or elongated loop). To master this technique of manufacturing the loop, you can on any shred associated with this interweaving. It’s not at all difficult at all. And then the buttons on your fasteners will always be in their places!

Good luck! And all the most magical and fabulous-good for you. Do a small job, but master it perfectly and treat it as a great thing. Remember that any work is a chance to learn. Follow the blog news. This is easy to do by issuing a blog news. We meet in the Комментарии и мнения владельцев. Your Mara (Marina Ostrovskaya).

There are nuances invisible to the inhabitant in the product, by which the master can quickly and accurately determine the sewing class. These include honeycombs of sleeves, lines, landing by figure. But one of the most important points is undoubtedly loops, including a loop with an eye. And it is the loops of the house of the mod that pay special attention. Despite the fact that you can perform a slotted loop with an eye on sewing equipment, the luxury class atelier on expensive coats and jackets are made exclusively by hand. And this operation is trusted only by the master with extensive experience.

Let’s master this necessary sewing operation and learn how to do exclusive slotted loops with an eye, because your products will only benefit from this!

Slear loop with the eye-master class

There are many different techniques for performing such loops, each master has his own chips and secrets. We will consider the most, in our opinion, a beautiful version of the loops. with a raised chain stitch.

To perform this sewing operation, we will need:

  • Thread Madeira Aerofil 5. You can also use any other strong threads 0 or 35, also use special durable silk threads. The threads are selected in the tone of the fabric of the product or contrasting, depending on the idea of ​​the designer. For clarity, we use yellow contrasting threads.
  • A piece of wax. The waxed thread is less “shaggy”, it is less confused, so the thread for the performance of the loops is pre.processed by a piece of wax.
  • Metal line for marking loops.
  • Rectangular line for marking loops.
  • Punch.
  • Awl.
  • Snacks.
  • A torn for loops. In case of an error, the jerkider will be very helpful.

Retreat from the edge of the product 2 cm and draw a fishing line for a trimmer of the edge, along which loops will be performed. Put from the line at right angles the width of the loop in the finished form (in our case, this is 2.5 cm). Place the loops at the same distance from each other. For a coat it is 11-12 cm, for jackets and men’s jackets 8-9 cm.

Sewing Velcro

Pour the fixing snares along the side. Around each loop, also lay the fixing snares so that they do not intersect with the marking of the loop. Measure the thread about 60 cm long, pushing, pressing the thread tightly to a piece of wax and stretching it along the wax.

To raise the loop, the lining thread is used. To prepare it, overheat the waxed thread in half, and begin to tighten on both sides in different directions when the threads are tightly twisted, beg in half again. the threads themselves will be twisted with each other. We received a laying thread consisting of 4 threads twisted together

Install the bunch on the edge of the loop, close to the selection, from the wrong side, put a piece of fabric folded several times. Try the “eye” of the future loop with snacks or straight scissors cut the loop by marking

Fix the end of the prepared lining thread using a pin and lay along the loop process the thread to make the loop wax, drive into the needle, make a knot and in the back of the product is in a distance of 2 cm from the edge of the loop (after the work, the thread is cut and removed).

Bring the needle to the outside at the edge of the loop, at a distance of 2 mm from the cut. Wrap the laying thread with a needle and inject the needle on the back, taking it to the outside close to the first puncture try to make punctures at the same distance from the cut. about 2 mm.

Author

Kerariel

| Denial of responsibility | Contacts |RSS