Home Refrigerators How to install a refrigerator Nord Frost
Refrigerators

How to install a refrigerator Nord Frost

What digit to put the thermostat in the refrigerator

The choice of temperature regime even in “smart” modern models is manually regulated.

The manufacturer sets the temperature range with the possibility of its change (usually from 2 ° C to 8 ° C for the refrigerator, and from.16 ° C to.24 ° C for freezer). Users have the opportunity to change these parameters and set up the temperature in the refrigerator for themselves. Therefore, before you start setting up the refrigerator for yourself, you must understand: what temperature do you want to get.

Temperature adjustment for modern and derived refrigerators from the production of refrigerators passes according to the same principles. The longer the refrigerator has been working, the more cold it will create. And vice versa. Therefore, by increasing the control value, we change the mode of operation upstairs.

install, refrigerator, nord, frost

Mechanical or electronic regulators are used to configure the mode.

mechanical. in the form of a wheel, rotary disk

electronic. digital scoreboard

The location depends on the refrigerator model.

  • inside the refrigerator on the wall on the right;
  • on the top panel of the refrigerator;
  • occasionally the regulator can be on the “ceiling” of the refrigerator.

What temperature corresponds to the number of thermostat.

Mechanical regulators are regulated by rotating the regulator handle. Rotating the regulator clockwise. we increase the cold, we reduce the clock. The numbers on the handle do not indicate the temperature in degrees Celsius. This is a serial number. They show in what position the regulator will be more cold, and in which less. Typically, the cold adjustment scale has values ​​from 1 to 7. The weakest cold will correspond to the number 1, it will be cold as possible on the number 6-7.

We increase the number. increase the cold. We recommend installing the number 3.

You should not without the need to set the value of 5-7, since the cold is achieved by a longer compressor operation and works with a greater load. In some cases, with such installations of a thermostat, a refrigerator-breaker may not turn off. Even if your refrigerator is disconnected, then electricity consumption increases significantly.

  • on the top panel of the refrigerator
  • The electronic board is mounted on the door, the display on the front surface of the door reports information about the state of temperature inside.

The electronic control of the refrigerator changes the operating mode by pressing the keyboxes. Basically used a control scale from 2 ° C to 8 ° C. Typically, next to the temperature value nearby is a button to change the characteristics. After each press on the button, the value increases by 1 degree. After reaching the maximum adjustment value, the refrigerator automatically goes into a minimum range.

  • Antiquity temperature greatly affects the operation of the refrigerator. The hotter around, the harder it is to create the necessary cold. Most of the refrigerators work normally at the air temperature range of 16-32 ° C degrees. Although the refrigerators have a different climatic class, you should not ask too low temperatures in the summer, since this can cause an increase in energy consumption and the load on the refrigerator. Above the temperature of the surrounding atmosphere is less the number on the regulator.
  • unequivocally say which number of the thermostat should be exhibited in the refrigerator is difficult. The temperature indicators in the refrigerator are determined by a large number of factors: technical condition, refrigerator load, room temperature, door opening frequency, etc.D.
  • Spend the quality of cooling regularly or install a stationary thermometer.
  • If when turning the regulator or changing the value on a digital scoreboard, the real temperature remains the same, call the master.

The choice of temperature regime even in “smart” modern models is manually regulated.

The manufacturer sets the temperature range with the possibility of its change (usually from 2 ° C to 8 ° C for the refrigerator, and from.16 ° C to.24 ° C for freezer). Users have the opportunity to change these parameters and set up the temperature in the refrigerator for themselves. Therefore, before you start setting up the refrigerator for yourself, you must understand: what temperature do you want to get.

Temperature adjustment for modern and derived refrigerators from the production of refrigerators passes according to the same principles. The longer the refrigerator has been working, the more cold it will create. And vice versa. Therefore, by increasing the control value, we change the mode of operation upstairs.

Mechanical or electronic regulators are used to configure the mode.

mechanical. in the form of a wheel, rotary disk

electronic. digital scoreboard

The location depends on the refrigerator model.

  • inside the refrigerator on the wall on the right;
  • on the top panel of the refrigerator;
  • occasionally the regulator can be on the “ceiling” of the refrigerator.

Basic rules for choosing a place

With any installation, you need to consider the features of the room:

  • What gender in the apartment. quality, material, availability of changes (the latter is relevant for Khrushchevs),
  • Is there a dedicated wire from the input electric meter,
  • how far out sockets, sources of heat and water are located,
  • And how the unit will look in the interior with existing furniture.

The floor is durable

Before installing in the room, carefully study the floors. they must be quite strong and motionless. It is impossible to install a large-sized refrigerator on the coating, which differs with softness (4-5 layers of linoleum) and freely spring-for example, on the thickness of the thickness of up to 3 cm, located with a large gap. Because of the vibration, the motor will buzz louder, especially at night, and will soon fail.

If the coating is planned and spring, protect the surface of the floor with a plywood with a thickness of at least 4-5 mm.

It is better to install equipment on concrete. such a floor can withstand even a two.door two.chamber unit of the maximum height. The finish of the coating can be any, but for bulky equipment, a tile base is more suitable.

Heat is away

To install the freezer and refrigerator, the rooms are considered in the distance from the heat sources. If you do not follow this rule, the unit will quickly fail. The compressor operates constantly, because the device heats up, as a result, the air inside the chamber needs to be regularly cooled. With prolonged operation, the thermostat fails in such conditions, and soon the engine.

For the same reason, refrigerators and freezers do not put next to the windows. in the summer they heat up in the same way as the batteries and break faster. Exception. cases when the air conditioner is in the room.

It is also impossible to put such a technique next to a gas or electric stove. if the plate is often used, it releases a lot of heat.

The minimum distance from heat sources: from the battery. 30 cm, from the stove. 50 cm.

Rosettes. closer

Pay attention to the presence of sockets nearby. The best option is the presence of a power source near the device.

  • Lay in the project at the stage of construction of a direct wire from an electric shield.
  • Buy rosettes with grounding (small antennae on the case).
  • But even if there is no socket nearby, do not use a few extension cords. All energy from them will accumulate on the first “tee” included in the fork, the network will be overloaded. and this is a serious risk of fire.

Water is an enemy

Do not install the refrigerator near the sinks, cranes, washing machines and water pipes: even if they are not close, spray will still reach the refrigerator. and you will hit the current from the body. The perfect distance from water is 2-3 m.

Instructions for the correct installation

Typically, in the kit with household appliances, instructions with detailed rules for transporting, installation, first inclusion and maintenance. If it is not at hand, follow the rules:

  • If the refrigerator was transported horizontally, wait for two to three hours before the first turned on.
  • Recommended distance from the wall to the rear panel of the unit. 10 cm. 5 can be 5, but air microcirculation will deteriorate.
  • Provide free access. the door should freely open to the maximum angle.
  • To prevent sliding, silicone or plastic stickers on the floor are used. the unit will make no less noise and will not “run” around the kitchen.
  • A sofa and a kitchen corner should not stand near the device. If there is no way to change the furniture location scheme, it is recommended to set the refrigerator so that the distance between it and the interior items is at least 10 cm.

If the listed rules are fulfilled, the risk of overheating of the mechanism, power loss, failure of the tier of the hike or other nodes are reduced.

How to move or move properly

The refrigerator can be rolled around the kitchen using a pair of rear wheels. Tilt a little back and pull the lower part on ourselves.

Avoid sharp inclinations. the device can be dropped by the radiator on the floor. After such a fall, not all units continue to work, often repair is required.

Fix the power cable on the lattice from the back of the device. If the wire will drain on the floor, it is easy to kill, cut off or spoil the insulation. For fixation, fasteners are used. plastic clamps.

Electricity and cables

To ensure the safe operation of the device, connect it to the electrical panel through the circuit breaker (RCD). Ideally. highlight a separate outlet for the refrigerator. In extreme cases, use the extension cord. but only one.

If you cannot connect the unit to a separate outlet, use the network filter. it will ensure the safety of the technique of any brand (AEG, Beko, Electrolux, LG, Indesit, Samsung, Whirlpool, B OSCH, etc.). With a voltage difference, instead of thin electronics, an external fuse will burn.

install, refrigerator, nord, frost

Alignment in level

Install the refrigerator in the selected place so that it stands motionless and evenly, otherwise it will beat, “jump” and “walk” in the kitchen. The fact is that during the compressor operation the device vibrates, so it constantly shifts on an uneven surface. This negatively affects the main nodes.

Adjusting the front legs

Adjust the position of the front legs so that the doors of the refrigerator are closed automatically under your own weight. Legs. two plastic washers on bolts located from below at the front. They allow you to change the angle of the unit for 1-2 degrees. The magnetic seal will do its job and seal the camera.

If the floor is even, without differences (for example, bulk or industrial). just place the equipment in the right place and adjust the position of the front legs. If the floor is uneven, check the slope at the construction level.

  • Detachment the device back a little so that the legs are in the air.
  • Manually twist them clockwise (to reduce the height) or counterclockwise, achieve the optimal position.
  • Gently lower the equipment and roll with a bubble at the construction level.

The final stage

  • At the last stage, set the shelves in the upper camera, and the boxes in the freezer.
  • Change the position of the thermostat by choosing the average temperature regime.
  • Perform the first launch of the device, stick the fork in the outlet.

The device of the refrigerator “Nord

Each two.chamber refrigerator “Nord” has one compressor that escaces the cold. The heated refrigerant under pressure is fed into the capacitor, where it is converted from a gaseous state into a liquid one and when it hits the evaporator, it takes heat from the refrigerator chamber. The device has a sealed refrigerator unit. The freezer in the refrigerators “Nord” can have an upper or lower placement. Units meet all the requirements of sanitary and environmental safety. The compressor of the refrigerator accumulates pressure, which exceeds, for example, pressure in the home water supply up to eight times. Evaporator can accumulate condensate and requires defrosting. Modern models are ensured by the forced exposure of the evaporator, which guarantees their dryness, and such refrigerators do not need to defrost.

The advantages of a two.chamber refrigerator

When choosing a refrigerator, you should pay attention to the number of cameras. What are the advantages of a device with two cameras? Nord two.chamber refrigerator has a large capacity and allows you to store products even for a large family. The dimensions of the freezer department can vary, so you can choose the required volume. Fans of fans of large reserves of frozen products are suitable for units with large freezers of three boxes, a small freezer will be enough for the usual current storage. The advantage of two.chamber devices is better storage. When opening a common chamber, warm air does not fall into the frost zone. In a separate freezer chamber, foods are frozen faster and preserve the nutritional properties better. The ability to configure each camera is another undoubted advantage of such devices.

The simplified diagram of the refrigerator “Nord” of the two.chamber includes eight main elements:

  • Compressor.
  • Thermal circuit.
  • Capacitor, he is a coil.
  • Filter.
  • Capillary tube (small section).
  • The evaporator of the refrigerator.
  • Evaporator of the freezer.
  • Vasic tube.

The scheme is clearly presented in the figure. Different models of refrigerators do not have fundamental differences in the scheme. Most often, the differences are associated with the internal equipment of the device. Traditionally, zones with high humidity for storing fruits and vegetables are released inside the refrigerator, special compartments are equipped. for bottles or eggs, for example. Also, more and more often in modern devices a special cooling zone is distinguished, in which you can store meat or fish for several days.

Checking the quality of the goods

Upon your claim, the seller has the right to check the quality of the goods. In this regard, we remind you of the need to provide the purchased goods along with a claim to the return point of the goods or provide the seller with the opportunity to pick up the goods to be delivered to the authorized service center to confirm the deficiency.

A delivery service employee fixes the fact of receiving the goods on the diagnosis by the relevant act filled in duplicate, one of which remains on the hands of the buyer.

Based on the results of such a quality test, the seller will provide you with a response to your claim.

If you do not agree with the results of the quality check, you have the right to submit a written requirement for an independent examination of the goods. Examination is carried out at the expense of the seller. You have the right to be present during the examination. If the examination establishes the availability of deficiencies that arose not through the fault of the store or manufacturer, you must compensate the store for the expertise, as well as expenses related to its conduct.

Article 26.one. Remote method for selling goods

The retail purchase and sale agreement may be concluded on the basis of the consumer’s acquaintance with the seller’s description proposed by the seller through catalogs, avenues, booklets, photographs, communications (television, postal, radio communications and others) or other excluding the possibility of directly familiarizing the consumer with a product or a model of goods under concluding such an agreement (remote method of selling goods) in ways.

The seller must be provided to the consumer to the consumer about the main consumer properties of the goods, about the address (location) of the seller, about the place of manufacture of the goods, on the full company name (name) of the seller (manufacturer), on the price and on the conditions of purchase of the goods, about his delivery, service life, expiration date and warranty period, on the procedure for payment of goods, as well as on the period during which there is a proposal for the conclusion of the contract.

At the time of delivery of the goods, the consumer must be provided in writing about the goods provided for in Article 10 of this Law, as well as the information provided for by paragraph 4 of this article on the procedure and the deadline for returning the goods.

The consumer has the right to refuse the goods at any time before transferring it, and after the transfer of the goods. within seven days.

If the information on the procedure and terms for returning goods of good quality was not provided in writing at the time of delivery of the goods, the consumer has the right to refuse the goods within three months from the date of transfer of the goods. The return of goods of good quality is possible if its presentation, consumer properties, as well as a document confirming the fact and conditions for the purchase of the specified goods are preserved. The absence of a document confirming the fact and conditions for the purchase of goods does not deprive him of the opportunity to refer to other evidence of the purchase of goods from this seller. The consumer is not entitled to abandon the goods of proper quality, which has individually defined properties, if the specified product can be used exclusively by the consumer acquiring it. If the consumer refuses the goods, the seller must return him the amount of money paid by the consumer under the contract, with the exception of the seller’s expenses for the delivery of the returned goods from the consumer, no later than ten days from the date of presenting the consumer of the corresponding claim.

The consequences of the sale of goods of inadequate quality by a remote way of selling goods are established by the provisions provided for in Articles 18. 24 of this Law.

Checking the quality of the goods

Upon your claim, the seller has the right to check the quality of the goods. In this regard, we remind you of the need to provide the purchased goods along with a claim to the return point of the goods or provide the seller with the opportunity to pick up the goods to be delivered to the authorized service center to confirm the deficiency.

A delivery service employee fixes the fact of receiving the goods on the diagnosis by the relevant act filled in duplicate, one of which remains on the hands of the buyer.

Based on the results of such a quality test, the seller will provide you with a response to your claim.

If you do not agree with the results of the quality check, you have the right to submit a written requirement for an independent examination of the goods. Examination is carried out at the expense of the seller. You have the right to be present during the examination. If the examination establishes the availability of deficiencies that arose not through the fault of the store or manufacturer, you must compensate the store for the expertise, as well as expenses related to its conduct.

Article 26.one. Remote method for selling goods

The retail purchase and sale agreement may be concluded on the basis of the consumer’s acquaintance with the seller’s description proposed by the seller through catalogs, avenues, booklets, photographs, communications (television, postal, radio communications and others) or other excluding the possibility of directly familiarizing the consumer with a product or a model of goods under concluding such an agreement (remote method of selling goods) in ways.

The seller must be provided to the consumer to the consumer about the main consumer properties of the goods, about the address (location) of the seller, about the place of manufacture of the goods, on the full company name (name) of the seller (manufacturer), on the price and on the conditions of purchase of the goods, about his delivery, service life, expiration date and warranty period, on the procedure for payment of goods, as well as on the period during which there is a proposal for the conclusion of the contract.

At the time of delivery of the goods, the consumer must be provided in writing about the goods provided for in Article 10 of this Law, as well as the information provided for by paragraph 4 of this article on the procedure and the deadline for returning the goods.

The consumer has the right to refuse the goods at any time before transferring it, and after the transfer of the goods. within seven days.

If the information on the procedure and terms for returning goods of good quality was not provided in writing at the time of delivery of the goods, the consumer has the right to refuse the goods within three months from the date of transfer of the goods. The return of goods of good quality is possible if its presentation, consumer properties, as well as a document confirming the fact and conditions for the purchase of the specified goods are preserved. The absence of a document confirming the fact and conditions for the purchase of goods does not deprive him of the opportunity to refer to other evidence of the purchase of goods from this seller. The consumer is not entitled to abandon the goods of proper quality, which has individually defined properties, if the specified product can be used exclusively by the consumer acquiring it. If the consumer refuses the goods, the seller must return him the amount of money paid by the consumer under the contract, with the exception of the seller’s expenses for the delivery of the returned goods from the consumer, no later than ten days from the date of presenting the consumer of the corresponding claim.

The consequences of the sale of goods of inadequate quality by a remote way of selling goods are established by the provisions provided for in Articles 18. 24 of this Law.

How much time the refrigerator should stand?

It is recommended to defend the refrigerator at least 4 hours. During transportation, it is tilted, due to this, the oil in the compressor and the refrigerant occupy, let’s say, an abnormal position, which is why serious problems may occur up to the compressor breakdown.

The refrigerator after transportation cannot be turned on immediately, since this is fraught with condensate formation and subsequent interruptions in work.

When you can turn on the refrigerator after transportation on the side?

To ensure uninterrupted operation of the device, you need to figure out how much you can turn on the refrigerator after transportation. When transporting equipment on the side. It is necessary that it settles in the winter for 16-18 hours, and in the summer-8 hours. During this time, the refrigerant will be distributed along the contour, and the oil drains into the compressor.

The compressor of the refrigerator will work actively until it cools the chamber space to the desired temperature. This happens about the same time as cooling at the first turned on after the purchase-from 2-3 to 8-10 hours.

When you can lay food in a new refrigerator?

Important! After turning on the refrigerator on the network, it is not allowed to place products immediately inside, as the device is gaining cold. To catch up with the desired temperature regime, it will take him from 5 hours to a day, depending on the attitudes made by the user, as well as many other factors.

  • Leave the gap (at least 10 cm) between the unit housing and the wall so that the system does not occur;
  • Do not install a household device next to the radiator, gas stove or oven
  • Check the serviceability of the outlet and electrical wiring, which should be grounded;

How much time the refrigerator should stand?

It is recommended to defend the refrigerator at least 4 hours. During transportation, it is tilted, due to this, the oil in the compressor and the refrigerant occupy, let’s say, an abnormal position, which is why serious problems may occur up to the compressor breakdown.

The refrigerator after transportation cannot be turned on immediately, since this is fraught with condensate formation and subsequent interruptions in work.

The importance of the “No Frost” system

So what does no frost mean? Literal meaning “without hoarfrost”. Such a system is designed to clean the internal space of the unit as much as possible of intention and icing. If this is not done, then the cooling surfaces “grow” in layers of hoarfrost, which turns into ice. This prevents the full.fledged appropriate of cold temperature, and the atmosphere inside the refrigerator begins to heat.

As a result, products, in an environment with high temperature, are faster covered with bacteria and deteriorate. An unpleasant odor appears inside, which is absorbed into the plastic walls of the refrigerator and begins to spread to all products. The opening of the door of the unit contributes to the smell in the apartment. To prevent all these negative consequences, the “No Frost” function has been developed.

The principle of operation of the system

How the No Frost system works in the refrigerator, it is easy to understand if you compare its action with the functioning of ordinary cooling equipment. Most models are equipped with automatic defrosting without stopping work. This happens conveniently and imperceptibly for the user:

    Circulations circulating freon according to the internal system.

  • In the included state, a reduced temperature occurs from the cooling elements, as a result of which frozen droplets of moisture from the air are formed on the back wall of the interior.
  • When the compressor stops, the temperature gradually rises, and the frozen drops flow down into a special canal, which transfers them to a shallow capacity.
  • The compressor turns on and heats up from work. The received water evaporates from its hot case, and new drops continue to form inside the refrigerator.

This is how periodic removal of moisture from the internal parts of the refrigeration equipment is ensured. This allows you to maintain good transfer of low temperatures and proper storage of products.

The problem of this technology is that the cold is distributed unevenly in the interior space. Typically, the evaporator is placed in the rear wall of the upper half of the case, where the temperature is below. This creates certain difficulties in arranging products. For example, if you put fresh tomatoes close to the back of the camera, they will freeze and deteriorate.

Milk, set too close to the door, will be in the most “warm” part of the refrigerator and quickly sour. When using such a device, you constantly need to remember the correct location of different products.

The No Frost system in the refrigerator provides two tasks: it eliminates the hoarfrost and creates uniform distribution of cold, regardless of the location of food on the shelves.

This is achieved due to the location of the evaporator between the freezer and the refrigerator compartment. The operation of the system is complemented by an internal fan that moves cold air throughout the space.

In all departments, holes are created that contribute to mixing the chilled stream. Moisture is effectively removed from all over the closed space and is transferred to a hot compressor for evaporation. Products are in equally cold state, regardless of the place of production on the shelves.

NordFrost refrigerators. Instructions and manuals

To view the instructions NordFrost refrigerators, select the necessary model from the list below or for convenience use the search. All operating manuals are presented in Russian or schematically. After switching to the model page, please wait for the download instructions for use or download it to your device. You can ask the remaining questions in the appropriate form on the page.

We constantly replenish our catalog with new instructions and manuals so that you can find the necessary model of the device and get acquainted with it online or download. All guidelines for use and operation are presented in Russian if you have not found the answer to your question, do not hesitate to ask it in the Комментарии и мнения владельцев.

Author

Laidred

| Denial of responsibility | Contacts |RSS