How to decorate a chimney in the interior: 13 proven ideas
Pipes of engineering communications are like blood vessels that feed the entire house with the necessary resources. But outwardly they are not very aesthetically pleasing, and often run in the wrong place, bringing disharmony to the interior. There are two ways: hide or embellish. Which way do you choose?? Let’s discover a few secrets about how to decorate the pipes in the interior.
Examples of successful masking
Ways to design the unit and communications in the interior of the kitchen can be divided depending on the type of gas equipment in your kitchen in an apartment with independent heating, home or cottage. Can be:
With a closed chamber. the most common and safe option. In apartment buildings, this type is encountered. It can be hidden behind cupboard or cabinet doors, installed in a niche.
how to hide a boiler in bedroom
In a wall-mounted cabinet
The boiler is located above the sink. The mezzanine floor is open.
In this case, be sure to take care of free air flow to the unit. For this purpose:
- Do not make a close connection between the walls of the boiler to the walls of the cabinet,
- Do not place the boiler in a blank cupboard. Top and bottom must be left completely open.
This type of placement is not the most successful, t.к. Bottom and top not fully open. But depending on the type of equipment, this arrangement may be acceptable and comply with safety regulations. Refer to the instructions for the unit or consult a gas technician.
In a cabinet
Installing the equipment in a pen in the kitchen solves two problems at the same time. masking the device itself and its communications.
In the niche of the headset
So that the boiler does not stand out in the kitchen interior, the garnish should be purchased in the tone of the unit or buy a speaker with a beautiful panel.
In some cases, even in contrast, it does not violate the design.
In the corner
Niche near the sink can be advantageously used for the installation of the boiler. The hinged row of the sideboard with a corner location, as in the photo below, can also hide the unit.
Masking the boiler with the color of the kitchen walls
If the boiler is already there, and you are not going to change or paint it, you can blend into the interior, painting the walls to match his tone.
Masking in the color of the headset
This idea is relevant if you order a set with a ready-made niche for the equipment.
In loft style or other, with industrial motifs, the speaker with an open vent will meet the rules of design.
In the pantry
You can build a garage for the gas equipment yourself taking into account all safety requirements.
Painted decor
This method can be relevant for all styles:
How to hide the pipes in the bathroom: a review of the best ways to mask the pipeline
You will agree that even the most original design solution of the bathroom interior design can come to naught because of unsightly engineering communications. You can save the situation by cleverly masking the unpresentable elements.
It is not necessary to be a virtuoso in the construction business, it is enough to choose finishing and construction materials, prepare tools and stock up on free time.
We advise you how to hide the pipes in the bathroom, while ensuring access for maintenance of the system. After studying our instructions, you yourself can transform the bathroom, saving money on the services of plumbers.
Chimney: how to close
Under the ceiling, a chimney runs to the vent. It has a larger size than pipes and hoses, and consists of a corrugated or rectangular metal box.
It’s impossible to remove and our job is to make it less noticeable. We apply any available method:
- cover with decorative panels;
- build a hinged shelf over it;
- We cover it with color-matched PVC film;
- we use vinyl stickers;
- Create a thematic (abstract, pattern) drawing.
If you really want a boiler in the bathroom?
In general, it is useless to argue with gas inspectors, they almost never meet the requirements in this matter. But if you want, you can try to get official permission.
To do this, you should make an official application in 2 copies to the head of the department of the gas supplier company. A copy of the room layout must be attached to the application.

Your application must necessarily be registered by the receiving party, a certificate of acceptance must be stamped on your copy. The organization will send a response with the obligatory legal grounds for refusal (or permission) within 15 days.
With this document, if you are not satisfied with the decision, you can appeal to the courts, but, as a rule, the court leaves such claims unsatisfied. So don’t get your hopes up.
Can gas appliances be installed in bathrooms and toilets?
Quite recently, the question of whether you can install a gas boiler in the bathroom, the answer was unequivocal and as they say not subject to debate. “No, you can not”. Prior to 2002, while the previous standard was in effect, it was not possible to install a gas boiler in the bathroom. The document did not stipulate any exceptions or possibilities, in which such installation would be possible, it was just a prohibition.
In the new documents SNiP SNiP 31-02-2001 and 42-01-2002 “Gas-distributing systems” has not added clarity, there are indications that the installation is prohibited in high-risk areas, and that it is forbidden to lay gas pipes through air shafts, but directly, and does not say that placing the boiler or a boiler in the bathroom or toilet is not possible.
This state of affairs allows a certain freedom of action, because if we are guided by the principle “everything that is not prohibited, is allowed” it is theoretically possible to achieve this, even on official grounds.
What’s the penalty for installing a gas boiler in the bathroom?
The reasons why it is forbidden to install gas equipment seem unreasonable to many people. But the penalty for unauthorized installation is quite serious. Self-installation is at least a penalty, forced removal.
Unscrupulous users bypass the law. They order design papers so that they list the room as a boiler room. Bathroom, respectively, are excluded from the plan-project. Gas unit is installed and connected. After that, all the plumbing is back in its place. The apartment owner safely forgets about the troubles and problems with documents.
In a year, when the gas inspectors check the work of the boiler, the irregularities will come to light. The employee will draw up a report and write a fine, the minimum amount of which is 45,000.
Legal reference! If the illegal installation of gas equipment has caused damage to another person’s property, resulting in the loss of health or life, there is criminal responsibility and a real term of 2 to 5 years.

Advice! If you do decide to put a boiler in the toilet, do it legally. Since the regulatory documents do not regulate a strict ban on installation, proceed as follows:
- Apply to the head of the gas organization with a request to install the boiler in the bathroom or toilet;
- Give a reason for your request, state the reasons why you insist on the installation in this particular place;
- Attach supporting documents;
- If your arguments are not enough, write a statement of claim in court. There is a chance that the decision will be made in favor of the plaintiff.
How to begin correctly?
Do not take the example of those who prefer to do everything “by eye”. You should start with a project of the future wiring. It may seem superfluous and even too complicated, but, nevertheless, such a project is necessary.
With its help, you can accurately determine the optimal location for each plumbing fixture, select the necessary parts and elements of the piping and determine their consumption.
To start the project it is recommended to make a list of plumbing equipment to be placed in the bathroom. It is important to know that if the house toilet and bathroom are separated, you need to perform the wiring project for both rooms. This is because their communications are connected and can not be mounted separately.
After determining the list of plumbing fixtures, you should mark which pipes should be brought to each of the devices.
- Bathtub of any type or shower stall. Cold, hot water supply, as well as sewage is connected.
- Washbasin-sink. Sewer, hot and cold running water will be installed.
- Bidet. Connects with the hot and cold water piping and with the sewage system.
- WC. Cold water and sewage mains are connected.
- Washing machine. Sewer and cold water supply is connected.
The next step is to draw a base diagram of the future project. For this purpose, accurate measurements of the room are taken, on the basis of which the scheme is subsequently constructed. It is desirable to perform it on the millimeter in a suitable scale.
All dimensions must be exactly right. This is an important condition for a competent project. All plumbing fixtures must also be measured. Their dimensions are needed in order to “fit” the equipment in the room as accurately as possible.
If you have not yet made a final decision on the location of the plumbing, you can proceed as follows. On paper, exactly according to the measurements made in accordance with the scale of the room, build a schematic representation of each sanitary appliance.
The template is cut out, and the resulting figures place on the floor, achieving an optimal arrangement of devices.
At the same time you need to consider the following requirements. The toilet is traditionally installed first from the riser pipe. Optimally, that its output through the fitting connected to the riser. A large distance from the riser, and the more the presence of turns in the pipeline will provoke clogging and will not allow the equipment to operate normally.
Plumbing fixtures should preferably be located so that the runoff from them flowed through the toilet bowl. This will be a very good prevention of blockages.
In addition to the toilet as close as possible to the sewage riser pipe to place a bathtub or shower stall with a low flush. It is necessary to prevent possible problems with the slope. The rest of the plumbing equipment can be placed at any convenient distance.
In addition, it is advisable to carefully study the technical documentation for plumbing equipment for its connection. If you assume a typical option, which provides a single-level location of the pipeline and the axis of the sewer outlet of the device, no problems will not arise.
If you are planning a non-typical connection, you should be prepared for all its features.
Most often, variations in the connection can be at toilets. Depending on the model, their drain can be straight or inclined, as well as directed towards the floor or wall. Technology for installing a toilet bowl with an oblique outlet has its own characteristics.
Atypical may be the connection of shower cabins and bathtubs. Their drain connections can have different configurations. All these features must be taken into account at the design stage.
After the places of installation of plumbing fixtures are fixed, the work begins with the placement of suitable piping to them. The scale of the scheme should be strictly observed, only in this way it will be possible to perform the correct wiring of pipes in the bathroom.
An Important Thing. Doing the “arrangement” of plumbing and furniture, do not forget that all the doors in the room should be free to open and each device should be convenient to use.
How to hide the washing machine in the bathroom
If there is no suitable place to place the washing machine, the bathroom would be a great option. As practice shows, not all people like to leave the washing process in plain sight. Professional designers know how to hide the washing machine in the bathroom. For this purpose, there are many options. behind decorative panels, mirror, curtains, doors.
Often a sink is installed above the washing machine. On the one hand it is very convenient, on the other hand it is quite simple and quickly feasible. It is an economical, practical option in case the bathroom is small. Countertops, covering the washing machine can be of different sizes, designs, colors.
Regardless of the final decision, when planning the design, it is advisable to combine aesthetics, convenience. In the bathroom it is particularly difficult to do, because there are a lot of devices, equipment, various not always aesthetic objects. This is when the question arises, how to hide the washing machine in the bathroom. Designers of NSDgroup have a great experience in this sphere, so they will be glad to help you to organize your bathroom space beautifully, aesthetically, functionally, practically.

Photo @nsdgroup.com.ua_: How to hide the washing machine in the bathroom