Tefal FV9450
Looking for positive and negative reviews about Tefal FV9450?
We’ve compiled 14 negative, negative and positive reviews from 11 sources.
We’ll show you all the pros and cons of the Tefal FV9450 revealed through user use. We do not hide anything and post all positive and negative honest customer reviews about Tefal FV9450, as well as offer alternative products similar. Is it worth it to buy. The decision is yours!
The best deals on Tefal FV9450
Supergliss is equipped with our best in glide Durilium technology soleplate. As millions of consumers in the world, you can rely on the Durilium technology invented by Tefal to make your ironing sessions fast and easy.
No. Before you put the iron away, make sure it cools down. Follow 4 steps: empty the residual water in the reservoir, turn the thermostat to minimum, close the steam regulator and set the iron on a rack (depending on the model).
If your iron is fitted with an anti-scale system, you must clean the valve once a month.
To do this, unplug the iron from the mains and let it cool down for 30-45 minutes. Pour out the water and remove the valve by holding it by the top. Immerse the valve in a glass of cold water, add lemon juice (or white vinegar) and let it rest for 4 hours. Then rinse the valve with plenty of water and put it back in the iron. Warning! Never touch the tip of the descaling valve.
To use the iron safely, take the following precautions.
Most importantly, don’t leave the iron unattended.In this way you can not only protect the iron or the surface on which it is placed from overheating but also avoid burns. If safety is your first priority, choose an iron with an automatic shut-off function.Never leave a hot iron within reach of children or pets! Risk of injury from the iron tipping over!
Like any other electrical appliance, the iron must not be immersed in water.
Do not use an iron that has fallen or has a damaged cord. If you have the slightest doubt that your iron is working properly, call Customer Services.
Always unplug the iron before leaving, cleaning or filling with water (except for models with a removable water tank). Check the water level regularly; it must always be sufficient.
Shake your iron gently to switch it on. The lights will start to flash and the heating process will resume.
If the iron has not been moved for 8 minutes or more (on the support or base), or if the iron is left in a horizontal position for more than 30 seconds, the electronic system shuts off the power supply, after which the auto shut off indicator lights up. Shake the iron lightly until the light goes out to turn it on.
SUPERGLISS
No. Make sure the iron has cooled down before putting it away. Follow the 4 recommendations: pour out the remaining water in the reservoir, set the thermostat to minimum, close the steam regulator and set it on a rack (depending on the model).
If the iron is equipped with an anti-scale system, the valve should be cleaned once a month.
To do this, unplug the iron from the mains and let it cool down for 30-45 minutes. Pour out the water and remove the valve by holding it by the top. Immerse the valve in a glass of cold water, add lemon juice (or white vinegar) and let it stand for 4 hours. Then rinse the valve with plenty of water and put it back in the iron. Warning! Never touch the tip of the scale-relief valve.
Follow all safety precautions to ensure safe use of your iron.
Most importantly, do not leave the iron unattended.This not only protects the iron or the surface on which it is placed from overheating, but also prevents burns. If safety is your first priority, choose an iron with an automatic shut-off function.Never leave a hot iron within reach of children or pets! Risk of injury from the iron tipping over!
Like any electrical appliance, you must never immerse your iron in water.
Do not use an iron that has fallen or has a damaged cord. If you have the slightest doubt about the working order of your iron, contact your customer service center.
Always unplug the iron before leaving, cleaning or filling with water (except for models that have a removable water tank). Check the water level regularly to make sure it is always sufficient.
What water to put in the iron and why it is worth paying attention to?
Iron is a necessary household appliance, it is impossible to imagine life without it. This device allows you to put things in order, ridding them of folds and creases. Nowadays modern models of irons allowed to make the process of ironing easy and comfortable household occupation. And all because the product has a special function of steam and water supply, thanks to which ironing is several times faster, more efficient and comfortable. And here it is important to pay attention to such an aspect as water for the iron. Why this factor is so important? The whole point is that the water “touches” important elements in the design of the iron and affects the functionality of the device itself, as well as the procedure and efficiency of ironing. That is, if you use poor quality or unsuitable liquid in the iron, limescale will soon appear and the device will lose its functionality, and can even fail. Another consequence of using “bad” water. the formation of stains on clothes after ironing. To avoid all of this, you need to know how to use an iron with steam, namely, what water you can pour into the iron.
What water to put in the iron with a steam generator
Despite the large variety of irons that have built-in protection against limescale, it is better not to take the risk and fill the steamers only with special water for ironing. It is completely free of harmful impurities, so it will not harm either the clothes or the appliance. So what kind of water to put in the iron for steaming?
Special
Considering what kind of liquid to pour into the reservoir, it should be noted that special water for irons is sold in many hardware stores. It does not contain harmful salts, so it does not leave white spots. In the manufacturing process it is softened and completely cleared of minerals that can be deposited on the walls of the evaporator. The only disadvantage of such a liquid is high cost. If you constantly pour it into the tank, it can affect the family budget.
Filtered
Filtered water is one of the best ironing fluids imaginable. As it passes through the filters, it is well cleared of salts, so it is ideal for use in steam generators. However, before pouring such a liquid into your iron, you should find out what kind of filtration you are using. A home purification system should have filters that work for softening.
How to use a steam iron properly without water leakage & clean it using self-clean method
Demineralized
This kind of water is obtained by deionizing it through organic resins. They tend to attract particles of acids and metal ions, which allows purifying the liquid from unnecessary impurities. While telling you what kind of liquid you should pour into your iron, it’s important to mention that after deionization, the purified water should be diluted with tap water at a ratio of 1 to 1.
Diluted distillate
The distillate itself is clean and may well be used for ironing. It has a high boiling point, however, so it evaporates badly and can damage the steamer. It is recommended to dilute it to avoid trouble. For this, one part distillate is mixed with two parts tap water.
Review: Tefal FV3145 Supergliss 45 iron. Works flawlessly!
The ironing wheel is also blue. It has three modes marked on it as standard:. synthetics;-silk;-cotton.
The water tank holds two hundred ml. of water, this is enough for me for one small ironing. I pour cold water here, with the iron off.Pouring water here is not very convenient, it’s easy to spill it, so I pour it into a container with a sharp spout, such as a teapot.
Surface coatings. Supergliss. This surface is smooth, but the white stripes on it, like the serial number on a banknote, are convex.The surface is scratch resistant, but in spite of this, one small scratch has occurred during the entire period of use.
TEFAL STEAM IRON GV8976 | PRO EXPRESS TOTAL REVIEW
Also, there are holes on this surface which let water in when you select steam mode.
.I would not call the iron lightweight, for me this is one of the drawbacks. When you iron a mountain of laundry, especially bedding, your hands get a little tired.Tefal FV3145 Supergliss 45 iron is easy to hold in the hand, it is convenient to iron.
Limescale protection system in this model does not, this is also not very good. Our water is very hard and if after ironing it stays in the iron, then through the holes accumulated limescale falls out.
It has a self-cleaning system, but I didn’t use it.The cord length of the iron is 1,8 m, it’s also enough, I can easily reach the outlet.The plug of the iron is pretty heavy, once it fell on my foot, I will not write what I said, it hurt a lot.
You can iron with this iron without water, but to be honest I don’t do it that way because it does not iron well without water.You can use the water spray function for convenience. Water goes in through this little hole.
The steam function can be activated in two ways. The first one. Move the groove on the iron spout. It will steam constantly until the water runs out.
Second. I would have to say that the iron is not bad, but I would only give it a “B”, because it is close to the handle, next to the water spray button. Here steam comes out only when you press the button, briefly. That’s what I use the most.
Tefal FV3145 Supergliss has a power of 45. 1500 Watt.No automatic shutdown here, the iron is old, but this is not a problem for me. But I would not give it to my mother-in-law.It also has a chute for buttons. It is convenient, but the iron has a wide spout and will not fit through.
To summarize, I would like to say that the Tefal FV3145 Supergliss 45 iron is not bad, but I would only give it a four with a small minus.

The biggest plus. Quality and good ironing.If I do change it for another iron, it will be a Tefal.
What does an iron do if the valve is faulty??
The principle of operation of the iron: water is supplied from the reservoir through the control valve to the inner part of the soleplate. There is a special regulator on the body of the steam iron, which increases or decreases its holes so that the liquid gets on the working surface in a certain amount. It turns into steam at high temperature and escapes through small holes on the soleplate of the iron.
Even if ironing device was used according to the manufacturer instructions, the liquid may still leak from the holes in the soleplate when the valve is completely closed and the temperature of the appliance working surface is low. The most likely cause of this defect is a faulty valve. To see for yourself, pour water into the iron, turn off the steam, without turning on the electric network 220 V, roll it a little bit horizontally. If the water will flow out of the device, it means that the valve does not close the holes for its delivery.
It is a pressing problem for many owners of this type of appliances. The valve, which is responsible for regulating the flow of steam, has rubber elements. gaskets. They become less elastic under the effect of high temperature over time, which leads to leaky operation of the valve.
This type of failure should be dealt with by authorized service centers, with appropriate qualifications.
What is a steam iron with a steam generator?
An iron with a steam generator differs from a classic model in that it has a boiler, which holds water for steaming. When heated to boiling temperature, it flows in the form of steam through a hose (hydraulic hose) and comes out through the holes of the soleplate under pressure.
Compared to budget irons, steam irons moisten fabrics 3-7 times more intensively. Pressurized steam escapes nonstop, penetrating 3 to 4 layers of fabric and softening the fibers. High temperatures from the heated soleplate quickly smooth out creases.
Your device has fewer clogs than an ordinary iron:
- Steam station cuts the time needed to iron pants, jackets, shirts and other items by a third.
- Powerful steam flashes to clean and sanitize your clothes.
- The device allows you to steam things that can’t be ironed with a regular iron: fur coats, sheepskin coats, dresses with lots of frills.
- The steam escaping under pressure removes odors from clothing.
Using the steam generator is not difficult, you just need to follow a number of simple rules.
What to put in the iron?
So what to steam? Tap water, hot, filtered or boiled? Or maybe you should buy distilled? In addition, in many stores you can find a special soldered water for irons on sale.
All of these issues are important enough, because using the wrong water can even cause the iron to break or shorten its life.
How to refill your iron with water CORRECTLY
We decided to find out from specialists of this equipment producers how to properly take care of your iron. So we had a real virtual round table, where we discussed all the nuances of working with this technique.
Julia Logvinenkova. Tefal Brand Manager: you should put regular tap water in the iron. If your area has very hard water, you can mix tap water and purchased demineralized water in a 50/50 ratio, t. к. Distilled water is harder to evaporate, and it can destroy the silicone coating in the evaporation chamber. Boiled water contains a little sediment, which can accelerate the deposition of plaque.
Anna Paklina. Philips brand manager: many Philips irons have a self-cleaning limescale feature, so you can even fill them with tap water. Distilled and flavoured water may contain organic or mineral substances, which when heated increases the concentration of the iron, you could ruin the iron and get stains on your clothes.
Tsukanova Catherine. Brand manager for Bosch, Siemens: We recommend that only pure tap water without any additives be used, due to the construction of the irons. For continuous, trouble-free operation of the steam function, you can mix tap water with distilled water in the ratio of 1:1. If the water in your region is very hard, mix tap water with distilled water in the ratio of 1:2.
Braun specialists: all modern models of irons have tanks that are designed to use regular tap water. In the rare case that your iron doesn’t have any protection against limescale or you have hard water, you can use a mixture of 1/2 tap water and 1/2 distilled water.
It is categorically not recommended to use completely distilled water, flavored or softened water, or water from the refrigerator, and to include additives (such as starch) in the water.
There is an opinion: add a couple of drops of your perfume into the water poured into the iron and the clothes will smell nice. Is this an acceptable tip or not??
Logvinenkova Julia. Tefal Brand manager: We don’t recommend putting any fragrances in the iron, because it makes your clothes smell nice.к. they can ruin the chemistry of the built-in limescale cartridge. Fragrances and antistatic agents are best used during laundry.
Paklina Anna. Philips brand manager: According to the user manual, you can’t put anything else in the iron except water.
Tsukanova Ekaterina. Brand manager for Bosch, Siemens brands: this advice is unacceptable, because the addition of any liquids, and in particular fragrances, can damage the appliance. In addition, the oils in the spirits burn and cause a pungent, unpleasant odor.