The procedure for including a storage water heater in the apartment
During the disconnection of hot water, there is a need to find an alternative, and then modern technology comes to the rescue. In order not to be left without the benefits of the civilization that we are used to, you will have to buy and install a storage water heater.
Quite often, I have to make inclusion in the summer, but not because this is some kind of difficult procedure, but because it is not often necessary to do it, and therefore people forget the sequence of actions, and therefore decided to write an article on this topic.
The inclusion of a storage boiler does not require any professional knowledge, but at the same time it is necessary to observe a certain sequence, since the structure of these devices, regardless of the model (Ariston, burning, Termyx, electrolyux), is the same for everyone, the procedure for inclusion in everyone is the same.
I’ll make a reservation right away, I tell you how to turn on the water heater with the correct standard connection scheme.
How to determine where the input of cold water and the output is hot:
According to the standard, if you look at the boiler, the supply of cold water. right, and the exit is hot. left, and cold is marked in blue, and hot. red.
- First, we block the hot water supply valve to the apartment, even if there is a check valve, since they tend to break, then open the same water on the mixer. It is necessary to open it in order to lower the air if the water heater is empty.
- Open a hot crane from the boiler.
- Open the cold tap for feeding into the device and wait for air to get out of the mixer you open and the liquid will flow.
- When the water flowed, close and turn on the boiler in the outlet, and after a couple of hours you can use it.
That’s the whole process, for more clarity, watch this video, and, I think, you will not have problems. You can turn off the device in the reverse order, but whether it is necessary to drain water from it, you decide.
Zanussi Zwh/S 30 Splendore XP 2.0 Silver operating instructions online [1/4]
it is not possible to have the right to vide the same and to give the use of.
Before installing the water heater, the certificate is that the grounding electrode of the outlet is properly ground-
linen. In the absence of a grounding electrode in a socket, it is necessary to ground a water heater from a delicious
grounding wire to the output of grounding on the fasteners of the flange of the heating element. In the absence
It is forbidden to use portable sockets.Incorrect installation and operation of electric water heating-
Internal tanks are made of high.quality medical stainless steel. As an addition-
the water heater is equipped with a magnesium anode by a magnesium anode. Do not forget
conduct regular, at least 1 time per year, maintenance and, if necessary, replacement of magnesium
The heating element (TEN), reliable and safe in operation, has a long service life of
Interior thickened polyurethane foam insulation allows you to effectively manage the temperature of the inhum-
Built.in temperature reg-
Before heating water, the digital display will show the temperature of the cold water that falls in the water-
Vatel. Using the adjustment handle, you can set the heating temperature up to 75 ° C. Adjustment scale
stop the propagation of bacteria, for example Legionell, multiplying in water with long.term non.use
Regardless of the selected power mode, using the street handle, you can choose the temperature, before
which needs to heat water. To the way, water is heated to a given temperature, then on the display display-
the regime is selected. Kog and heating to a given temperature occurred, then the selected power mode
At Stanovka, a watch timer: when clutching the upper “° C” button for 5 seconds, the lower number begins to flash 00, when
repeated pressing the upper “° C” button increases by 1 hour, when the upper “° C” button is squeezed, increases
5 seconds after the last press, the system accepts the set time, in standby mode, heating
“Antimovishment”. Initially, the power mode 1, pressing the button once turns on the power mode 2,
By pressing the power button twice in a row, the power mode of power is turned on, pressing three times in a row
“Antimproduction” mode. Когда режим «Антизамерзание» активируется, на экране будет индицироваться символ
How to turn on the Boiler
“NF”, if the temperature drops to 4 ° C, the power mode 3 is activated and the water will be heated to 5 ° C. When
The water in the tank reaches 5 ° C, the heating elements will be de.energized. This mode will be active, only
kog and a temperature adjustment handle on the control panel are not in the extreme left Polo of the Off (kog yes
The water heater is not turned off). To get out of the “anti.frustration” mode, you need to twist the adjustment handle-
doors and immediately turn on the power mode 1, or then press the power selection button, while also
for three seconds. This mode works in parallel with power modes 1, 2 and 3. When activated
This mode, the SC characters will light up on the screen for 1 second every 3 seconds. In intervals
Between indicating the symbols “SC” on the display, the current water temperature in the tank will be displayed. The
The mode will be activated at 3 a.m. Kog and mode will be active on the screen constantly burning “SC”.
The first activation of the regime will be 3 days after installation, then once a week. If suddenly disconnected
electricity and then its feed will be, the time counter continues the report without starting the countdown first. To
After the mode is made out of this mode, characters will no longer be indicated on the screen
Relieve that original parts are used to install an electric water heater,-
placed by the manufacturer, which is why you have a lot of weight on the floor of the non.doe to. Without setting up-
Leeze the water heater for the mount until you make sure that the mount is installed reliably. Otherwise
case, an electric water heater may fall from the wall, which will lead to its damage or may
cause serious injuries. When choosing places for holes for fasteners, a certificate
On both sides of the walls of the bathroom or other room to the body of the water heater there is a gap not
less than 0.2 m, and from the part of the connection of pipes of at least 0.5 m, to facilitate access during technical-
If water falls into the water heater, water falls directly from wells, wells or water towers, for
the operation of the water heater must be used to use the TR Crief Cleaning films, for the post of falling in
In stanchist water heaters of the SPLENDORE XP (Silver) series, it is significantly facilitated by the ability to install them
both vertically and horizontally anywhere in your house, in heated (!) the room. Preferably
pipes length, the less heat loss. As shown in rice. 5a, with a horizontal installation of a water heater
The eyeliner pipes should be located on the right. When installing a water heater near the wall, leave
Zanussi zwh/s 50 Smalto DL Instruction Instruction Institution online. Page 7
Instructions Zanussi Zwh/S 50 Smalto DL for device a water heater contains pages in Russian.
File size: 944.88 KB. Consists of 24 pages.
You can download PDF file of this instruction: download pdf
Filling water after installing the water heater Open the water supply valve. Open the hot water crane on the mixer. As soon as the water heater is filled, water will flow from it, close the hot water crane on the mixer and make sure there are no leaks. In case of uncertainty, whether there is water in the water heater, do not connect it to the mains.
one. Control Panel.2. Turning on/off handle
water temperature in the water heater (shutdown of heating).
the temperature of the water heating in the water heater (inclusion of heating).
ECO. a label of an economical mode complying with
Coys the temperature of the water heating in the water heater up to 55 ° C.
High. the label on the right corresponds to the maxi
a small temperature of water heating in a water heater (75 ° C)
Power indicator. burns yellow
when the water heater is included in the network.
Heatihg indicator. burns white,
when the heating element works and the water heating works.
one. Control Panel.2. Button “ON”/”OFF” Turning on/off
The adjustment control handle is carried out by rotating the handle only clockwise, from the minimum value to the maximum. The installed temperature is reflected in the display. After reaching the maximum heating temperature and rotation of the adjustment handle further clockwise, the installation will begin again from the minimum value to the maximum. When installing an economical mode (5055 ° C), the ECO indicator will light up on the display.4. Power button. Choosing Full (2000 W)
or half (1200 W) heating power.
Indication of the selected power stage
How to Test & Replace the Heater on a Zanussi Washing Machine
the exit from the water heater, when the heating temperature is installed (using the temperature adjustment handle 3) the set temperature is displayed on the display, a few seconds after installing the desired heating temperature on the display, the water temperature at the outlet of the water heater will again be displayed.
Zanussi zwh/s 80 Smalto instructions for online. Page 8
Zanussi Zwh/S 80 Smalto instructions for the device water heater contains pages in Russian.
File size: 944.88 KB. Consists of 24 pages.
You can download PDF file of this instruction: download pdf
Connection to the network of models of Smaltovs, the water heater plug in the outlet. Turn on the water heater. The yellow indicator Power will light up. This means that the water heater is connected to the mains and power is supplied to it. Turn the power control regulator to the Low position to turn on the heating, the heating indicator will light up. Set by adjusting the heating temperature the necessary level of water heating. ECO indicator. economical mode corresponds to the heating temperature of about 55 ° C. Water heating is turned off automatically when the set temperature reaches and turns on automatically for heating. If you want to turn off the heating of the water, turn the switch handle in the OFF position, the heating indicator will go out. Power heating indicator will burn while the water heater will be connected to the mains. The thermostat will provide a re.turn on the heating element after spinning a certain amount of water if the water heater is turned on for heating.
Reliably grounded. The rated current of the outlet should be at least 10 A. The outlet and fork should always be dry in order to prevent a short circuit in the electric network. Periodically check if the fork is tightly inserted into the outlet. The verification method is as follows: insert the network fork into the outlet, turn off the water heater after half an hour and pull the fork out of the outlet. Pay attention to whether the plug is warm to the touch. If you feel with your hand that it is warm (at a temperature of more than 50 ° C), please replace the socket with another, where the fork enters tightly. This will help to avoid fire, damage to the fork or other accidents as a result of poor contact.
The wall on which water is installed
The heater should be designed for a load twice as much as the total weight of the water heater filled with water. Otherwise, additional measures should be taken to strengthen the product.
Connection to the network of models Smalto Dlvs to a water heater plug in a socket. After pressing the ON/OFF key, the water heater will turn on, the last set temperature or the factory setting installed during the first inclusion will flash for 2 seconds. After 2 seconds, the indication of the set temperature will go out and the water heating will begin. The display will show the temperature of the water in the water heater.
Installation of the temperature of the temperature of the water heater temperature from 30 ° C (minimum) to 75 ° C (maximum). The temperature is installed using the control knob located on the front panel of the device.
If electricity is disconnected in the room. If electricity is disconnected in
heating time, then after turning on the electricity in the room, the water heater will turn on to heating, as was installed before.
The safety valve follows the mouth
Put up at the site of the water entrance (see.Fig.12i13).
vatel (or during the first use after maintenance or cleaning) should not be included in the power of the water heater until the water is completely filled with water. During the filling of the water heater tank, open the hot water crane for air descent. As soon as the tank is filled with water and water will flow from the tap, the tap can be closed.
the release of the reverse safety valve pressure may come to water. This is a normal phenomenon. However, in the case of large leaks, contact specialists in maintenance. The opening of the pressure release under no circumstances should not be blocked; Otherwise, this may lead to a breakdown of the water heater.
Zanussi zwh/S-50 instruction manual online. Page 4
Zanussi Zwh/S-50 instruction for the device contains pages in Russian.
File size: 932.91 KB. Consists of 17 pages.
You can download PDF file of this instruction: download pdf
All storage water heaters of the ZWH/S series are designed to connect to an electric network with a single-phase voltage of 220/230 V. Before connecting, make sure that the parameters of the mains at the connection site are corresponded to the parameters indicated on the plate with the technician data of the device.When installing a water heater, the current electrical safety rules should be observed.When installing a water heater in the bathroom or toilet, restrictions related to the existence of prohibited and protective volumes should be taken into account.
Filling water after installing the water heater Open the water supply valve. Open the hot water crane on the mixer. As soon as the water heater is filled, water will flow out of it, close the hot water crane on the mixer and make sure that there are no leaks. In case of uncertainty, whether there is water in the water heater, do not connect it to the mains.
Connection to the power supply of the water heater in a socket and turn on the water heater. The yellow indicator “”. This means that the water heaters are connected to the mains and power is supplied to it. Turn the adjustment handle clockwise to turn on the heating, the heating indie “. Set by adjusting the heating temperature the necessary level of water heating. ECO indicator. economical
The power outlet should be reliable
ground. The rated current of the outlet should be at least 10 A. The outlet and fork must be dry all the way to prevent a short circuit in the electric network. Periodically check whether the fork is tightly inserted into the rosette. The verification method is as follows: insert a set fork into a socket, turn off the water heater after half an hour and pull the fork out of the outlet. Pay attention to whether the plug is warm to the touch. If you feel with your hand that it is warm (when
The forbidden volume is a space that is faced with tangential and vertical planes in relation to the outer edges of the bathtub, toilet or shower block and flat, located above them or above the floor, if the plumbing is mounted on the floor, at a high-cost of 2.25 m.The protective volume is a space that limits the horizontal planes of which coincide with the planes of the forbidden volume, and vertical planes are defended from the corresponding planes of the prohibited volume per 1 m.
The mode corresponds to the heating temperature of about 55 ° C. Water heating is turned off automatically when the set temperature reaches and is turned on automatically for heating. If you want to turn off the heating of the water, turn the handle of the inclusion in the “OFF” position, the heating indicator “” will go out. The power indicator “” will burn while the water heater will be connected to the mains. In some models, when the heating element is turned on, the light indicator will begin to flash. The thermostat will ensure the re-inclusion of the heating element after expanding a certain amount of water.
Installation of the temperature of the temperature adjustment of the water heater from 30 ° C (minimum) to 75 ° C (maximum). In the models of the Orfeus series, the temperature setting is performed using a regulator located on the front panel of the device.
temperatures over 50 ° C), please note the socket to another, where the fork enters it tightly. This will help to avoid fire, damage to the fork or other accidents as a result of poor contact.
The wall on which the water is installed-
The heatingler should be designed for a load twice as much as the total weight of a water heater filled with water. Otherwise, additional measures should be taken to strengthen the product.
The safety check valve follows
Install water in the place of entrance (cm. rice. 5).
When using the water heater first
(or during the first use after technical maintenance or cleaning), the water heater is not included in the water heater to half filled with water. During the filling of the water heater tank, open the hot water crane for air descent. As soon as the tank is filled with water and water will flow from the tap, the tap can be closed.
During the heating of water from the opening opening
the pressure of the reverse safety claw-pan can act water. This is a normal phenomenon. However, in case of large leaks, you should contact specialists in technical maintenance. The hole in the pressure of pressure under any circumstances should not be blocked; Otherwise, this may lead to a breakdown of the water heater.
On the opening of the pressure in the safety-
The drey pipe must be installed by a pavement and removed it into the sewer in case of water drainage. The drainage tube connected to the opening of the pressure of the pressure should be directed down.
Since the water temperature inside the water-
vatel can reach 75 ° C, hot water should not fall on the human body. In order to avoid burns, you can adjust the water temperature using a mixture crane.
With prolonged absence, conducting
repair, technological and preventive work on the water supply line or
It is necessary to block the individual locking valves on the water heater on the water heater in the water heater to the water heater and on the hotel output line, as well as turn off the water heater and disconnect from the power grid, taking out the fork from the outlet.
In the case of using a water heater
In rooms with a centralized supply of water, during the period of disconnecting hot water, overlap the shut-off valve of the supply of burning in the water from the supply highways (stroke).
The first inclusion of the boiler
After completing the installation of the system, it is recommended to check its performance. You need to act according to the instructions:
- Check the main elements of the system. If the boiler is gas, make sure that the gas enters through the allotted channels, there is no leak, incorrect connection. The electrical equipment checks the compounds of phases, zeros, the presence of reliable grounding. In the presence of automatic circuit breakers, tests are carried out using screwdrivers of electricians.
- Inspect adjacent plumbing for improper connection, gaps and holes in the pipes. Control the connection of the underwater channel, check the check valve.
- Run water into the boiler.
- Spend plumbing a second time.
- Test the operability of the water heater.
- Fix the initial degree mark on the panel, start the device.
Re-check thermometers after 15-20 minutes. If the degree rises, heat is successfully transmitted to the water.
The launch of water into the boiler is carried out in the following sequence:
- Disconnect the feed of hot water coming from the central water supply. This will prevent water from the boilers back into the pipes. In houses where the hot water is not held, nothing needs to be blocked.
- Make sure that the pipes are connected correctly: with blue rings. to the underwater part, with red. to the pipes for the supply of heated water.
- Open the underwater pipes valve to let the liquid into the drives.
- Secondly, the valve opens on the red pipe, the water goes into the water supply.
- Next, you need to open the appropriate crane and wait until the stream is leveled.
- If everything is regular, you can serve power: electricity or gas for the burner.
- At the last stage, it is enough to set the temperature regime, and the boiler is ready to use.
In a similar scheme, running water heaters are launched. Differences in only several points: you do not need to supply water to the container before opening the crane, you can immediately start the heater and control the performance of the devices.
What to do if the indicator light does not burn, and the water does not heat up
Firstly, it is necessary to check whether the power is supplied to the apparatus. Perhaps you began to use a water heater to heat water, but forgot to insert the fork of the network cord of the boiler into the outlet. If there are no problems with this, then check if there is a contact in the cable connecting the heater with the outlet or electrical panel, depending on how you have a connection.
If the water heater is connected to the network, but still does not work. set the handle of the thermostat. She can stand on minimum values. Turn the handle clockwise, the heater will work again.
If you turned the handle of the thermostat, but the heating did not start, most likely the protective thermostat worked. The inclusion of a protective thermostat is possible for a number of reasons: jumps in the tension, pollution of the apparatus, the formation of scale, etc. The protective mechanism starts automatically, turning off the device immediately after it is turned on.
To enable the water heater, you need to find the thermal protection button. In most cases, the button is located under the plastic cover at the bottom of the tank body. Before you remove the protective cover, you need to turn off the water heater from the mains. After the device is disconnected, you can remove the protective cover, press the thermal protection button, put the lid in place, and then re.connect the water heater to the network.
Water heaters have already become an integral technique of our life. If you follow all the recommendations and use the water heater correctly, then it will last a long life. But do not forget that boilers, like all household appliances, tend to break. If the breakdown is serious, and not one of the above methods has helped to solve your problem, do not try to disassemble and repair the equipment yourself. With more serious issues, the best option would be to appeal to an experienced specialist.
Subscribe to our YouTube,. Yandex Zen. There is a lot of useful and interesting content there!
Procedure
The connection sequence is suitable for both accumulative and flow instruments:
- Disconnect hot water. In the absence of this step, all your hot water will go into a common riser.
- Open the crane to release the remaining stagnant hot water.
- There are 2 pipes at the bottom of the water heater: one with blue, and the other with red. It is the latter that serves to supply heated water. Open the valve with a blue marker, and the water goes to the boiler.
- We turn the valve of the “red” pipe and wait for water to come from it.
- Open the faucet tap and water is pouring there.
- We connect our installation to the network and adjust to the desired temperature.
Boiler inclusion recommendations
Depending on the type of water heater, several options for turning on the water heater are distinguished. How to include the most famous brands of devices will be discussed later.
Launch of the water heater “Ariston”
After connecting the device to the mains, you must act according to the following algorithm:
- Pay attention to indicators that should light up on the panel of the device.
- Logging temperature light bulbs indicate that the water heater does not work.
- Press the button responsible for starting. Most often, such a key is located in the extreme corner of the panel.
- Adjust the required temperature using the corresponding keys.
- Install the required power. On boilers from Ariston, this parameter does not exceed 2500 watts.
Additional Information! Most devices for heating water automatically retain the initial settings. Therefore, in the future, the water heater will not have to set up.
How to launch a water heater “Electroilux”
There are several actions that need to be performed to enable the boiler of this brand:
- Connect the device to the network.
- Press the Power key.
- After completing the above points, the device display will be turned on.
- Adjust the indicators: temperature regime, heating power.
- Press the “Save selected Parameters” button
Important! Most of the heater of Electrluks is initially active in the “Energy Savings” mode. Some users can turn off this opportunity by going into the settings of the device.
Following the recommendations that were set out in this article, you can significantly increase the durability of the boiler.
