Home Article How to disassemble the plate Ariston electric
Article

How to disassemble the plate Ariston electric

How to disassemble the oven Ariston

After long operation, the built.in oven and door with glass must be thoroughly washed. Cleaning must be carried out not only externally, but also inside, since dirt and fat can fall under the glass. In order to wash, we need to remove it. And for this you need to remove the door.

  • Long.term operation of the oven. If the oven is used for several years, dirt and fat will go inside and stay on the back of the glass.
  • Violation of technological processes during the manufacture of a gas stove. If the glass was very stretched, cracks may appear.
  • Damage during transportation. Even telescopic cracks can lead to breakdown.
  • Error when mounting.
  • The glass can burst if the oven inside is preheated, and outwardly cold water will fall on it.

You can replace yourself. Buy glass should be in special stores.

Modern hobs

Then fashion trends of modern design came to the kitchen, and simple electric stoves no longer fit into the kitchen corners and sets of furniture. Hobs appeared, which are built into the countertop.

Such household appliances are not only beautiful, it is distinguished by expanded functionality. The heating element is controlled using electronic controllers, there are various security systems. Most of the products are equipped with control panels, you will not find a mechanical handle even in economy class models. To carry out the repair of a modern hob with your own hands, you must have basic knowledge in electronics.

Types of heating elements of a modern electric stove

The usual spiral in ceramic insulators has not been used for a long time. Instead, 3 types of electric heaters are used, both direct and indirect effects:

    Hilight direct heater is nothing more than a progressive descendant of a nichrome spiral. Is a corrugated ribbons made of metals with high resistance.

Looks and works just like a wire spiral. However, due to the form of execution, it gives thermal energy more efficiently, and serves much longer.Some manufacturers produce plates with traditional wire heaters. There is no fundamental difference (slightly lower effectiveness and reliability). But repairing a burned spiral is easier.Dishes (and its contents) heats up very quickly. However, such a system has a serious drawback: it is difficult to adjust the degree of heating. In fact, the heater operates in two modes: “Inclusive” and “off”. This does not mean that it is impossible to set the operating temperature, it is simply implemented this process is somewhat unusual. The electronic controller periodically turns off the power, and turns it on again. Thus, the amount of total heat energy is regulated. In this mode, it is difficult to cook dishes that require “small fire”, as on a gas burner.Another problem characteristic of this type of hob is a high temperature of the decorative surface. Outwardly, the plane does not look hot, so there is a danger of touching and obtaining a thermal burn.

The ability to burn your hand is the same as the previous design, in addition, there is another drawback. Haguens have a limited resource, therefore, repair of hobs with such heaters occurs much more often.

The system works on the principle of the transformer. The high frequency generator forms the corresponding alternating current on the primary winding (coil placed under the burner). The secondary winding is dishes, which must be made of metal with ferromagnetic properties, otherwise the magnetic field from the “primary” will work in idle. Steel or cast iron is suitable (can be checked with a magnet or by the presence of the icon “for induction plates”). Copper and aluminum dishes on such a burner will not heat up.Vorthy currents in the bottom of the dishes instantly heat the metal, and already a pan or pan act as a heating element (therefore this method is called indirect). Without dishes, the turned on the burner remains cold, which reduces the risk of getting burned. This is clearly seen in the illustration:

The degree of heating can be adjusted, but many housewives are confused by the restrictions on the material of the dishes. In addition, some buyers are afraid of induction radiation. In vain, this is not a microwave: an electromagnetic field is not higher than that of the iron on. And the malfunctions can only be associated with the electric circuit: the coil does not burn out.The main disadvantage of the induction fireflower is the high cost, which slightly limits the mass promotion “to the masses”.

Having sorted out the design of the heaters, you can repair your own hob.

DIY gas stove repair

Sooner or later, the need to make the repair of a gas stove overtles almost all the owners of these devices.

It’s often invoice to contact the master, and I would like to eliminate home problems so as not to waste time transporting tiles and repair.

There are a number of problems of gas plates, for example, adjusting the electric carpet, which you really can cope yourself with yourself.

The analysis of the most common breakdowns in the slabs and ways to solve them will help you with this, as well as a video that reflects all the stages of work.

Our advantages

The most frequent types of breakdowns of electric stoves are Ariston

The electric stoves of this manufacturer are reliable and durable, extremely rarely fail without the direct participation of their owner.

The common breakdowns of these household appliances include:

  • Figus of the heating element. occurs due to the use of dishes with an uneven bottom or too small diameter.
  • Formation of the hob-appears due to the use of too heavy utensils. Untimely repair of this malfunction leads to a short circuit and aggravation of the breakdown.
  • Damage to the switches or burners. occurs due to intensive long.term operation. The elimination of the problem requires high.quality spare parts, the installation of which the master should be carried out.

There were problems with an electric stove Ariston? Contact us!

ABC-Service specialists will diagnose your electric stove and quickly eliminate the problem.

For the repair services of the plates provided by our masters, a guarantee is provided.

To clarify the details, call: (495) 162-03-76.

The Master will be able to name the approximate total cost of repairs after the description of the electric stove malfunction by phone.

Diagnosis and restoration of indirect heating panels

Repair of induction hobs can only be experienced electricians. Without knowledge of the material, with a simple multimeter and pliers, the operation is doomed to failure. At the same time, many problems are not at all malfunctions: the usual violation of the operating mode.

Typical malfunctions of induction heating systems

  • Induction flax either does not turn on at all, or the food disappears immediately after the start of work. This can be a protective function: if you remove the dishes from the heating plane, or the size does not correspond to the diameter of the burner, the automation blocks the work. The same applies to aluminum or copper utensils.
  • The same problem (incorrect dishes) can lead to the fact that the induction imperial is not at full strength.
  • The independent inclusion of the heater may be associated with the pollution of the plate, or the presence of a massive steel (cast.iron) subject next to it.
disassemble, plate, ariston, electric

These malfunctions that are not related to violation of the operating mode are manifested in the diagram of the inductive field generator. As we have already noted, the winding fails extremely rarely.

In fact, there are no space technologies here. The transformer converts the supply voltage, and the generator creates an increased frequency of oscillations of the electromagnetic field. After a visual inspection (for clearly “burned” radio elements), the generator is checked using home oscilloscope. If you have such a device, it makes no sense to explain the principle of checking the inductance generator, your level is sufficient for repair.

If you do not have sufficient experience, you will have to contact the masters. In any case, the repair of a separate block will not cost as much as buying a new panel.

Tearing portal about repairing washing machines with your own hands, repair of dishwashers, repair of boilers and refrigerators

There are instructions for electric and gas plates, hobs and ovens of Ariston and HotPoint-Ariston. To download the leadership, you need to find a model of your device and click on the name, the file will open in a new tab.

The products of the company are known and loved all over the world thanks to several important parameters that highlight the brand among other manufacturers.

Firstly, HotPoint is distinguished by the ability to create smart equipment with a stylish design. The company has a long and rich history, vast experience, which allows you to use the latest technologies and development in production. Therefore, the products of this company always look unsurpassed in the kitchen and make our life easier, thanks to their outstanding characteristics.

Secondly, the devices of this manufacturer are smart, which means that they used innovations aimed at reducing electricity consumption. Technologies that are used in brand devices allow you to carefully spend natural resources.

Various devices can be used for cooking, but due to frequent use and intensive work, they are especially susceptible to breakdowns. Repair of electric stoves can be carried out with your own hands at home without taking a bulky equipment to a service center.

Despite external complexity, this device has a very simple design. All working elements are installed in a special heat.resistant cabinet made of alloy steel.

The principle of operation of the electric stove is based on heating the heater by leaking electric current on it. The device is equipped with heating elements that are necessary for cooking. They are ceramic, tubular, halogen, continuous.

  • Ceramic burners are presented in the form of a tube, so they can be used for any electric stoves and their repair is very easy to carry out yourself. The spiral is laid in the hole in the plate and fixed using special parts. Now glass ceramics are increasingly used, which is more affordable and durable, in addition, it is washed;
  • Halogen burners are considered economical, they work due to halogen lamps with reflectors. These lighting devices are installed in various areas of the hob and provide rapid heating and low electric energy consumption;
  • In old domestic tiles (dream, ZVI and others), cast.iron spiral hets were often installed. They slowly heated, but after disconnecting they gave the heat for a very long time. Separately, it is necessary to note their durability and resistance to moisture and the effects of high temperatures;
  • Tubular spiral made of a hollow pipe. When heated, it not only gives heat, but also promotes the circulation of warm air inside itself, which allows you to increase the efficiency of the device. This type of fireplace is most difficult to repair yourself.

To power the slab, a power wire is used, which is connected to all burners. In addition, they are also connected to regulators and thermostats that act as a system of safety system. After turning on, the wire begins to transfer energy to the heater, which is necessary for cooking. Control the level of heating and the burner must be using the corresponding handle. Many household plates of Ardo (Ardo), Indesit (Indesite), Electrolux (Electrolux), Zanussi (Zanussi) and others besides these devices also built.in timers and signaling devices. They help to control cooking time.

Photo. modern slab with halogen lamps and sensor

Unlike gas, electric stoves are considered quite safe in everyday use. Their repair and maintenance can be easily performed independently, and in terms of durability they are much better than gas models. In particular, this is because they can be cleaned at home, and not wait for the arrival of a specialist.

  • When working, the smell of burning appears. If the smell of burning food is worried, then the repair is not needed, it is required to clean the cooking surface. If it stinks of plastic or rubber, then you need to urgently call an electrician;
  • The burner does not warm. The reason may be the absence of voltage, the problem of the spiral or the control handle. It will be required to repair the burner or its wire;
  • The heating temperature is not tuned. It will definitely require repair of the mode switch;
  • The burner does not heat up. The frequent problem of desktop and stationary plates is that they crackle. They can be destroyed as a result of a blow or from a sharp temperature difference (for example, the spiral was heated, and cold water accidentally fell on it). This is the reason for the lack of heating of the burner or uneven heating of food. Independent repair of the spiral is very easy to carry out without the help of the master. the thicket of everything just needs to be replaced;
  • Bad work of the oven. Most likely, the problem also lies in the breakdown of the spiral.

It should be noted right away that the corporate service will not undertake to carry out warranty repairs after extraneous intervention. Therefore, if you do not have such an experience, then it is better to immediately contact specialized workshops.

The main components of the reeds of hobs of glass.ceramic surfaces (panels) Fig. And Fig. Are:

  • Glass.ceramic panel.
  • Brings.
  • Control module (if electronic management).
  • Charpits operating modes switches (if manual rice is controlled).

Repair of the Ariston Electric Book Panel DIY

Details: Repair of the Ariston electric hob with your own hands from a real master for Olenord.com.

The high technicability of the hobs is in doubt about the possibility of their repair with users and home masters. But, like all complex electronic equipment, kitchen surfaces consist of separate functional blocks interacting with each other.

Having understood the functionality and interaction of the components, having studied the methods of determining the frequently encountered malfunctions, realizing that it turns on, you can, without resorting to the services of the masters, to carry out a simple repair of the hob with your own hands.

All modern hobs work according to one principle. the user acts on control sensors, which includes power relay that switch large currents in heating elements.

Ремонт варочной поверхности Ariston KRA 640 REPAIR своими руками

Therefore, first you need to localize the breakdown, that is, determine the defective node. It is assumed that the cable, the connection terminals, the fuse, the presence of the voltage are checked, and the errors of the set of commands are excluded.

Varcation surfaces (panels) are called electric heaters (electric stoves) having glass.ceramic external coating. Glass ceramics have greater strength, which allows to withstand the significant weight of the dishes, and has good thermal conductivity.

The attractive appearance, which some manufacturers (for example, Hansa) complement artistic scenery, allows a stylish hob to fit successfully in the modern design of the kitchen.

Artistic design of the hob

Heating elements hidden under the glass.ceramic surface are several types:

  • Spiral, working like ordinary heating elements;
  • Corrugated ribbons (modified incandescent threads);
  • Halogen infrared lamps (Halolight technology);
  • Induction coils heating only the material of the dishes.

Various designs of thermoelectric fireplace

The firewalls of the first three types convert electric current into heat according to the law of Joule-Lenz according to the same principle, how the thread of incandescent in a conventional light bulb or spiral in the usual electric heating element heats up. The principle of heating using induction is described in detail in an article on induction boilers. With your own hands, the repair of induction hobs with your own hands will be described below.

Thermoelectric heaters have a thermal gofra or spiral, the connection terminals, as well as heating sensors, presented in the form of a bimetal plate located on the radius line or the diameter of the burner, stacked in heat.resistant material. Expanding, the bimetallic plate affects the contacts, closing or blurring them.

The device of the hob fireplane

Depending on the design of the hob, the contacts of the thermostat can be power (acting like a thermostat), or signal, included in the electronic control circuit. The malfunctions of sensors (thermostats) are a common cause that the hob that is not turned on.

In general, the repair of hobs is not much different from the repair of electric stoves, which is described in detail in one of the article of this resource. The main visual difference is the presence of a glass.ceramic surface and type of heaters, the spirals of which is visible through a transparent surface. The sensory electronic unit and the complete absence of the usual control levers is also a characteristic distinctive feature.

Hunch panel touch control unit

Therefore, the electronic touch control unit, which is also a display, is the greatest difficulty in repairing electric hobs. DIY repair will require knowledge in radio engineering and special equipment.

But otherwise, the hob is not much different from the electric stove. the heating elements are turned on by power relay, controlled by the electronic control board, which receives signals from the sensor.

But at first, without even disassembling the hock panel, you can determine the malfunction of the touch display and the electronic control unit. As a rule, the receipt of the command from the user is accompanied by a sound signal and is displayed on the display. If there is no reaction to touch, then it becomes clear that the breakdown in the sensor.

Indication of a regularly working hob

The sensitivity of the sensor may worsen due to severe surface contamination. It should be remembered that the entire glass.ceramic surface of the hock panel requires thorough care and cleaning, otherwise cracks may form from the accumulation of scale and handling.

The operation of a slab with cracked glass ceramics will lead to its further destruction and breakdown, so you need timely care and cleaning of the hobs, as shown

Do.it.yourself electric stove repair: diagnostics and methods for eliminating breakdowns

If an electric stove does not work or poorly operates, then it can be repaired independently, if there is a necessary set of tools and skills in working with electrical appliances. It is necessary to know and observe the safety rules when carrying out the repair process of this device.

disassemble, plate, ariston, electric

To fix the correctly and high.quality electric stove, it is worth preparing the following devices:

  • voltmeter;
  • ammeter;
  • current measuring ticks;
  • screwdrivers “feather” and “sting”;
  • heat-assembly tape, with a diameter of 8-12 mm;
  • pliers;
  • roundbones;
  • low voltage pointer (UNN) by a voltage class up to 1000 V;
  • Multimeter.

A set of the required tool for repairing an electric stove

The process of repairing the slab begins with disassembling the main components of the structure and dismantling the glass.ceramic hobs panel. There is no universal algorithm for this process, since modern models are distinguished by constructive features.

The first step is the dismantling of the hob that is attached to the countertop using 4 fasteners.

Removing fasteners when dismantling the hob

Beko electric stove models are produced with a ceramic hob. The disassembly of the case is to carefully remove the panel, it is not allowed to skew and strike with extraneous objects in order to avoid complete failure.

Types of faults and their elimination

Often, in the process of working and using devices, some malfunctions may occur that can greatly harm the operation of the electric stoves. To save the device, it is worth considering the main breakdown.

Damage of stoves with burners

If an electric stove is with burners, then if a malfunction is detected, it is necessary to act as follows:

  • unscrew the mount and ground conductor from the plate body;
  • Under the burner is a locking ring or spring, to take it out, you need to remove the spring and put the design itself with a sharp object;

Classification of firewood in diameter and power

Switch breakdown

If the switch and the breakdown is broken, it is possible to repair it independently:

  • If when turning the switch clockwise, there is no characteristic sound, then this may indicate the failure of the switch;
  • Checking the state consists in supplying voltage to the stove, automation of the control unit should be triggered after a certain period of time;
  • Before you remove the control handles, carefully study the documentation for the repair of the device;
  • To access the regulator, the front panel and the metal plate on which the regulator is fixed is removed;
  • A faulty step switch is replaced.

Electric grilled problems

Some modifications of Gorenje gas plates are equipped with electric grill. At the same time, they may have different malfunctions:

  • If the electric grill screw does not rotate, then we can say with confidence. the engine is out of order;
  • If, with mechanical forced rotation of the screw, jamming is not observed, then this means overheating of the stator or rotor winding from exposure to high temperature. To fully verify the engine breakdown, you need to measure the stator insulation resistance.

Another reason for the malfunction of hot air circulation in the electric grill may be dry lubrication in the “rolling. sliding” bearings and in the bushings.

  • unscrew the nuts that fix the front and rear cover of the engine;
  • remove the anchor from the stator, check the free course of the bearings;
  • If the move is jammed, then it is necessary to apply a new heat.resistant lubricant indicated in the factory instructions, or notice it on Litol 24.

Electronic module malfunction

To repair the electronic control module, you need to have certain knowledge in electronics and microprocessor technique. If there are no such features, then it is recommended to contact the service center for repair and maintenance of household appliances.

The process of removing the electronic slab control unit

Problems with power regulator

Sometimes there is a breakdown of the power regulator. If it is installed in the extreme right position to the maximum, and the heating of the electrocondor or the hob that does not occur, then this means a malfunction of the regulator. This electronic device is not subject to repair. its full replacement is necessary.

How to unlock the electric stove (induction cooker)

disassemble, plate, ariston, electric

Problems with the thermostat

Damage to the thermostat is in two cases:

disassemble, plate, ariston, electric
  • wear and burning of bimetallic plates inside;
  • lack of metallic contact with the body of the device, as well as oxidation of contacts at the entry into the thermostat.

Electric plates have a lot of advantages over gas devices, in addition, they are much safer, easy to operate. Repair of electric stoves in domestic conditions can be performed with your own hands without resorting to expensive services of specialized organizations. It is enough to have a minimum of knowledge in electrical engineering.

Author

Laidred

| Denial of responsibility | Contacts |RSS