Home Article How to disassemble and clean a ledeme faucet
Article

How to disassemble and clean a ledeme faucet

How to disassemble vidima faucet

Even if you buy a good-quality faucet, over time you still have to repair it and replace some parts. So how to disassemble a faucet like Grohe, Esko, Oute, Damixa, Swes, G Lauf, Ledeme, Molinari, Kaiser, etc.д. With your own hands is very easy, you do not need to turn to a professional plumber with this problem.

Single-lever faucets (with one handle) are the easiest faucets available (Damixa Arc. Damixa, Franke, Oras. Oras, Iddis). Their design is represented by a spout, a swivel lever, a locking nut, a gasket, a replacement ball or a cartridge.

Disassembling the single-lever ball valve

The water supply ball valve (Gustavsberg, Haiba, Rubineta, Shruder, Varion, Flora) is a type of single-lever. It is used to mix water, it is connected to two pipes: hot and cold. Temperature control and pressure is carried out by means of a ball, which also acts as a stopper element. The ball is a replaceable element.

Design of a single-lever ball faucet

Step-by-step instructions with a video on how to disassemble the ball single-lever faucet in the kitchen or bathroom:

  • Before starting work, it is required to completely turn off the water supply. Otherwise, boiling water may come pouring out of the water supply pipes during disassembly;
  • Next you need to remove the decorative plug, if you have one;

Remove the decorative plug from the faucet

After that, unscrew the screw with a screwdriver, which presses the rotary knob. This screw connects the handle to the stem of the locking fitting;

Use a screwdriver to remove the screw

Then the handle (control knob) should be removed from the body. It is necessary for water supply and is a regulating part;

Step 4

Next, use a wrench to unscrew the cap;

unscrew the cap

Step 6

After that, you can remove the ball mechanism. You need to be careful, often under the balls are built in springs, which help control the flow and temperature of water. Remove the locking mechanism carefully so as not to damage the fragile springs;

Remove the mixing ball

Using a screwdriver, carefully remove the valve seats and springs to them;

Step 8

Remove the swivel block of the mixer spout;

Step 9

Any water faucet, in addition to the locking mechanism, is equipped with two gaskets (O-rings), which are often located directly under it. They must also be removed and cleaned. If the gasket has rubbed too hard against the base, you need to pick it up with a thin flat screwdriver or a knife and replace it;

remove and replace, if necessary, sealing rings

Removing Hard Water Deposits From A Faucet Head

If the reason for the breakdown is that the faucet is simply clogged, for example, lime salts or other debris, the repair will go much faster. It is necessary according to the instructions above to remove the body and clean it with a special gel. Depending on the material of the spout, you need to choose the right cleaning agent. They are different for brass, copper and steel. Note that often the imported faucet (Italian, German, etc. д.) is equipped with a special sieve that is located directly under the spout. It should be cleaned with an old toothbrush and blown out.

Disassembly and repair tips from the expert:

  • Many models (Blanco Elipso, Hansberg Prestige, Hansgrohe, Sentosa, Mofem) are decorated with a special decorative panel. It can only be removed using a thin screwdriver. Lift the lid from the bottom, from the side of the body, and carefully lift it up;
  • If your aerator is dirty, you can put it in a container with vinegar for an hour to remove different dirt particles. Make sure to rinse with water before installation.
  • Ideally, you should buy a complete repair kit for your model in advance;
  • Before you disassemble the faucet, study the structure of your particular type of faucet.

How to disassemble a hinged single-lever faucet/bathroom faucet

How to disassemble a faucet with a cartridge

It should be noted that single-lever faucets with ceramic cartridges are now often installed for a washbasin or as a kitchen faucet. They are not replaceable, so if they break, you need to disassemble and throw away. But in most cases, the faucet with a ceramic cartridge will last a long time, so it rarely needs to be replaced.

In the photo. the construction of a single-lever faucet with a ceramic cartridge

And another video on how to disassemble the kitchen faucet with a ceramic cartridge

How to Disassemble a Dual-Flow Faucet. Step-by-Step Instructions

To disassemble a water two-lever half-turn faucet (Hansa Stela, Vidima, Frap. Frap) with a cartridge is quite simple, t. к. Each drain is connected to a separate lever, it is simple and practical to use. The valve models are often equipped with special plates that are lapped to each other.

Turning a valve opens a water flow of a certain temperature. Rubber or plastic gaskets are used for protection of these plates, which provide tightness of their joints and softness during movement. Kitchen faucet with a two-lever mechanism comes in two varieties:

Domestic herringbone faucet is still one of the most popular types of faucets for the kitchen and bathroom. The peculiarity of this design is the presence of a kind of a tee in the body, through which the drain pipes are connected to the lever.

The spigot is connected by means of pipes that are inserted directly into the spout, without the use of additional splitters.

Design of a wall-mounted two-handle mixer for sinks

How to disassemble a faucet with two handles:

  • Modern two-lever faucet can be dismantled only after unscrewing the lock screw, which is located under the decorative panel. But the old Soviet faucet has a more complicated design. Here you will need to remove the locking nut, under which is the valve, it is also unscrewed, opening access to the internal parts;
  • Under the screw is a faucet-box, which acts as a valve, it must be carefully disassembled and removed;
  • Under the bucket faucet there is a gasket or ring, which are needed to seal the structure. It should always be checked for integrity and cleanliness. Even a small speck can cause a leak in the faucet;
  • To assemble a two-lever faucet should follow the reverse scheme, pre-checking the connection of pipes and the integrity of the body.

If the body of a herringbone faucet is cracked, it cannot be repaired. Most often it happens with cheap Chinese faucets, such as Calorie and others.

How to disassemble the two-valve bath mixer

Two-valve

This procedure should not take you much time, because the design of a two-valve faucet is very simple. For this purpose, you should have only a screwdriver and a wrench. Be sure not to forget to turn off the hot and cold water supply. Now you can move on to the removal of the plugs on the cocks.

After installing them, the screws can be found. They should be removed with a screwdriver. After that, access to the rubber gaskets is open. But you can’t tell if it’s damaged just by looking at it. Most often the gaskets will need to change or tighten all connections, so that the mixer does not dangle.

Scale build-up inside the valve can be another cause of malfunction. Use a long flathead screwdriver to remove lime scale.

The video shows how to disassemble the faucet in the bathtub of the two-lever type:

The ball valve has a similar principle of disassembly, the design of which is equipped with two levers. Such a device is, of course, a little easier. If you use the presented recommendations, then the whole process of disassembling will not cause any difficulties, and you will spend minimum time on this.

Single Lever

The design of such a device implies a core and a hollow ball made of stainless steel. The ball has 3 openings, 2 of which are used to supply the liquid and one of which allows the mixed liquid to be discharged into the outlet pipe.

The ball is centered in a ball sleeve, and there are seats inside it. They are made of high-strength rubber. As a result of the pressure created by water the ball and seats are in tight contact. The ball starts to move thanks to the stem. It is the adjustment of this element that determines the change in water pressure and supply. If the contact area is small, the pressure will be high.

The video shows how to disassemble a faucet with one handle:

The ball mechanism has a long service life. If it is broken, it is often necessary to replace the valve. Among all the possible problems that can be corrected by your own efforts, there is only a weakening of the jet at the outlet of the device. This problem arises due to clogging of the aerator. To solve this problem it is worth dismantling the faucet, using the following plan of action:

  • Unscrew the nut located in the mixer spout.
  • Take out the strainer, blow it well and rinse it in the opposite direction.
  • Install the grid in its original place, and then screw the nut back on.

All repairs should take 10 minutes. If you want your faucet to last longer, then use the following recommendations:

  • Take care to install quality filters on the cold and hot water pipes;
  • Regularly use a single-arm faucet, regardless of its type, if the product will stand idle for a long time, it can get caked and break;
  • Only buy from trusted companies that guarantee the quality of their products.

A particular case. disassembly of the faucet Frap

If you have a frap faucet installed in the kitchen and bathroom, which has failed, then the process of disassembling it involves the following plan of action:

  • Shut off the water supply in your home or apartment.
  • Using a wrench 21, undo the screw under the water indicator and remove the mixer handle.
  • Then dismantle the appliance’s capsule containing the rubber seal. Replace this element with a new one, and reassemble the faucet according to the reverse scheme.

This video shows how to disassemble a frap faucet:

Single-lever

The design of such a device involves a core and a hollow ball made of stainless steel. The ball has 3 openings, 2 of which are for the fluid supply and one of which allows mixed fluid to be discharged into the outlet pipe.

The ball is concentrated in the ball sleeve, and there are seats inside it. High-strength rubber was used for their manufacture. As a result of the pressure created by the water, the ball is in tight contact with the seats. The ball begins to move due to the stem. It is the adjustment of this element that determines the change in the head and water supply. If the contact area is small, the head will be high.

This video shows how to disassemble a single handle faucet:

The ball mechanism has a long service life. If there is a breakdown, then most often it is necessary to replace the faucet. Of all the possible malfunctions that can be repaired by your own efforts, there is only a weakening of the jet at the outlet of the device. Such a problem arises because of clogging of the aerator. To solve it, you should disassemble the faucet, using the following plan of action:

  • Unscrew the nut located in the mixer spout.
  • Take out the strainer, blow it well and rinse it backwards.
  • Put the mesh back in its former place, and then screw the nut back on.

All repair work should take 10 minutes. If you want your faucet to last longer, use the following recommendations:

  • Take care to install quality filters on the cold and hot water pipes;
  • Regularly apply a one-handed faucet, regardless of its type, if the product will stand idle for a long time, it can get caked and break;
  • Only buy from trusted companies that guarantee the quality of their products.

A special case. disassembling a Frap faucet

If you have a frap faucet installed in your kitchen and bathroom that has failed, the process of disassembling it involves the following plan of action:

  • Shut off the water supply to your home or apartment.
  • Using a wrench for 21, unscrew the screw under the water indicator, remove the mixer handle.
  • After that, remove the appliance capsule, on which the rubber gasket is located. Replace this element with a new one, and reassemble the faucet in the reverse circuit.

The video shows how to disassemble the frap faucet:

Water faucet

As always, you should first shut off the cold and hot water. You can do this with the valves on the pipes. When the valves are closed, you can open the thumbscrews and let out all the accumulated liquid in the mixer.

To carry out the repair of the water faucet, you will need the following tools:

The procedure is as follows:

  • Dismantle the valve thumbscrew. This is done very simply with a screwdriver.
  • After removing the thumbscrew, take the adjustable wrench and unscrew the faucet head. After that you will be able to find the stem with a rubber gasket. This is the part that most often causes a malfunction.
  • Remove the old gasket using a screwdriver. If the gasket is attached by means of a screw, you should unscrew it.
  • When you have replaced the old gasket on the new one, take a clean cloth and clean the thread on the letter and in the hole, where it will be mounted.
  • wrap a few strands of oakum around the valve head, refit the bead. In this case, it should be noted that winding the oakum should be counterclockwise, but the bucket should be screwed in the direction of.
  • If the cause of the failure is the wear and tear of the “seat” of the faucet, then even a new gasket over time quickly comes into disrepair. To fix the problem encountered, you need to use a special cutter. It can be screwed, using a drill. Thus, all the roughnesses on the “seat” can be eliminated.

The video shows how to disassemble the kitchen faucet:

Peculiarities of disassembly of the faucet in the kitchen and bathroom

Today you can find modern models of faucets, installed in the bathroom or kitchen. They may be equipped with a timer or sensitive parts. To disassemble such a faucet, you should follow the following plan of action:

  • Remove the cover that serves to secure the batteries. After that, you can proceed to further disassemble the faucet, but only before doing so, it is important to turn off the water and electricity.
  • Disconnect the sensor wire from the control box.
  • Now remove the gasket that is located between the control box and the mixing tube.
  • Disconnect the nipples that lead from the heating and cold water supply pipes.
  • Remove the springs and retainers that hold the body to the base of the sink. Similar operations are carried out when disassembling models with a thermostat and a timer.

When the disassembly has been performed correctly, you can proceed to the repair. When the problem of the breakage is in the control unit, it is not recommended to make repairs with your own efforts, because there are fragile elements. Only an experienced specialist will help to solve the problem that has arisen.

In the video. how to disassemble the faucet in the bathroom and kitchen, the peculiarities of disassembly:

The faucet, like any plumbing appliance, can eventually become unusable. But this does not mean that you should immediately throw it away. First you need to disassemble the device and see what caused the breakage. If it is a spoiled gasket, you need to change it and reinstall the faucet in its place.

Ceramic cartridge for a faucet: what is it and what are they, which is better for a single-lever

Types of faucets for the bathroom with a shower. which one to choose by design

Types of faucets in the kitchen: which one is better to choose?

Overflow for the sink: how to install a sink siphon. installation and mounting

Half-turn

The evolution of the double-flush design has been completed by the modernization of the locking and regulating mechanism. Instead of the valve with a rubber gasket in the box we installed a half-turn ceramic disk shutter. The modern shower distributor is implemented with a similar head.

The process of disassembling the half-turn valve is reduced to the following:

    Unscrew the cap (there are plastic ones, on latches) on the thumbturn by hand or with pliers.

Remove the decorative plug. Unscrew the screw that secures the handle to the stem.

Remove the fixing screw of the thumbturn. Pull off handle.

Pull the handle. Unscrew the decorative cap.

Unscrew the decorative cap. Use an appropriate wrench to unscrew the head.

Unscrew the head. Remove the faucet head.

Two-valve

Over time, any faucet will start to drip, no matter how tighten the thumbturn. Probable reason is valve (piston) gasket wear and tear, it is necessary to unscrew the head for inspection. The operation is not complicated:

The structure of a two-valve faucet.

Let’s take off the lug nut. Remove the thumbscrew.

Unscrew the thumbscrew. Remove the thumbturn.

Removing the lamb. Unscrew the decorative cover, sometimes it has an Allen key on it, sometimes it is unscrewed by hand.

Unscrew the cap. Unscrew and remove the tap cup.

To disconnect the spout unscrew the union nut, then pull out of the housing, in which it is held by rubber rings. In older round types the seal is applied directly in the grooves in the tube. At modern flat. on the transition fitting.

When the water does not stop dripping from the shower head, revise the ball switch. In addition to the bowl, the upper shower branch must be disconnected. Next:

  • Remove the handle of the switch in the same way as with the thumbscrews.
  • Unscrew the central connector that the stem goes through.
  • Completely release with an Allen wrench the upper, lower retaining clips, in the fluoroplastic (ceramic) saddles of which the ball rotates. When assembling, to avoid jamming, screw in alternately to the same number of threads, adjusting the clamp.
  • Loose knot lets water in, preferably a small tension that allows you to turn the handle with your fingers.
  • Take out the stem with the ball.

How to repair the nut by yourself?

Remove the spout, and the upper and lower caprone rings.

Using a thin object, pry open the rubber seals and carefully remove them from the special technological grooves. Work carefully, do not leave depressions in the grooves, because of them there may be new leaks.

Now let’s replace the worn out jam nut. You can make it out of discs you don’t need.

Carefully trace the nut on the disc with a compass or awl, making sure that the outer and inner diameters are not shifted. With sharp little scissors, cut out the part along the outer contour.

Heat a piece of wire on the gas burner of the kitchen stove and make a hole in the center of the workpiece, without it it is impossible to remove the inner part of the disk.

Use scissors to carefully remove the inside diameter. The disc is in two parts, separate them.

All components of the future nut should fit tightly into the threads, fit them with a small round file. You have to make 6 of these blanks.

Screw the elements on the threads one by one and glue them together using a special resin adhesive. This is a very effective compound, gluing is performed by the method of molecular welding.

Press the tap vertically and allow it to dry.

While the nut is drying, check the condition of the aerator. The device is designed to saturate the water with air, thereby reducing splashing. Unscrew the body of the aerator, take out the internal parts and clean the narrow slots from dirt and oxide. Check the condition of the rubber seal and replace it if necessary.

The glue has hardened. continue assembling the mixer.

Assemble the mixer

Do not forget that a handmade nut does not have the same strength, and the individual elements must be assembled with great care.

Unscrew the nut and check its travel. Put on new rubber seals.

Important. Pay attention to the position of the rings, tapered surfaces should be directed towards each other. Due to this position, the internal water pressure will additionally unclench the gaskets and increase the tightness of the fit.

Carefully place the spout on the tap, remembering to put the bottom capron gasket in its place. It acts as a bearing when the spout is turned. It is recommended to use technical vaseline or ordinary soapy water to make the process easier. Moisten the surfaces, the composition will greatly reduce the friction forces and facilitate the assembly process.

Put on the upper gasket and tighten the nut made of discs. Tighten it with a little effort. Remember that the task of the nut is not to compress the capron gaskets or rubber seals, but only to hold all parts of the valve together and prevent them from wobbling.

One more thing. The compression force of the nut will increase after the faucet is finally installed on the sink and the device is secured with studs with a washer.

The faucet is assembled, it is advisable to check for leaks. To do this, temporarily connect the hoses to the water supply and turn on the faucet. You should see leaks in a few seconds. If everything is normal, you can install the device in its place. Disassembly, repair and assembly takes no more than two hours, it is much faster and cheaper than going shopping for a new lever mixer.

How to disassemble a single-lever faucet in the bathroom and kitchen. step-by-step instructions

Single-lever (with one handle) are the easiest of all existing faucets (Damixa Arc. Damixa, Franke, Oras. Oras, Iddis). Their design is represented by a spout, a swivel lever, a fixing nut, a gasket, a replacement ball or a cartridge.

Disassembly of the single-lever mixing valve

Ball water faucet (Gustavsberg, Haiba, Rubineta, Shruder, Varion, Flora) is a type of single-lever. It is used to mix water, it is connected to two pipes: hot and cold. Temperature and pressure control are controlled by a ball, which also acts as a locking element. The ball is a replaceable element.

Design of a single-lever ball faucet

Step-by-step instructions with video, how to disassemble the ball single-lever faucet in the kitchen or bathroom:

  • You need to turn off the water supply completely before starting work. Otherwise, boiling water may come out of the water supply pipes during disassembly;
  • Next, you need to remove the decorative plug, if you have one;

Take out the decorative plug in the mixer After that, unscrew the screw with a screwdriver, which presses the swivel controller. This screw connects the handle to the stem of the shut-off valve;

Use a screwdriver to unscrew the screw Then the handle (control knob) must be removed from the housing. It is necessary for water supply and is a regulating detail;

Step 4 Next, use a wrench to unscrew the cap;

unscrew the cap Remove the cam by hand;

Step 6 After that, you can remove the ball mechanism. We need to be careful, there are often springs installed under the balls, which help control the flow and temperature of the water. Remove the locking mechanism carefully so as not to damage the fragile springs;

take out the mixing ball With a screwdriver, carefully remove the valve seats and springs to them;

Step 8 Remove the swivel block of the faucet spout;

Step 9 Any water faucet in addition to the shut-off mechanism is equipped with two gaskets (o-rings), which are often located directly underneath it. They should also be removed and cleaned. If the gasket has rubbed too hard against the base, you need to pry it up with a thin flat screwdriver or knife and replace it;

If the reason for the breakdown is simply because the faucet is clogged, for example, with lime salts or other debris, then the repair will proceed much more quickly. It is necessary to remove the body according to the instructions above and clean it with a special gel. Depending on the material of the spout the correct cleaning agent must be selected. They are different for brass, copper and steel. Note that often the imported faucet (Italian, German, etc. д.) Equipped with a special sieve that goes directly under the spout. It should be cleaned with an old toothbrush and blown out.

How to Disassemble & Clean a Brumby Tap

Disassembly and repair tips from the expert:

  • Many models (Blanco Elipso, Hansberg Prestige, Hansgrohe, Sentosa, Mofem) are decorated with a special decor panel. It can be removed only with a thin screwdriver. The lid is lifted up carefully from the underside of the housing and is then carefully lifted off;
  • If your aerator is dirty, you can put it in a container with vinegar for an hour to remove the dirt particles. Before installation be sure to rinse with water.
  • Ideally, you should buy a complete repair kit for your model beforehand;
  • Before disassembling, first understand the construction of your type of faucet.

How to disassemble a hinged single-lever faucet/bathroom faucet https://www.YouTube.com/watch?v=K1K2Sw0428U

How to take apart a faucet with a cartridge

It should be noted that single-lever faucets with ceramic cartridges are now often installed for the sink or as a kitchen faucet. They are not replaceable, so if they break they must be disassembled and discarded. But in most cases, a faucet with a ceramic cartridge will last a long time, so its replacement is rarely needed.

A photo. a device of the single lever faucet with a ceramic cartridge A photo. dismantling diagram of a faucet with a cartridge

And another video instruction on how to disassemble a kitchen faucet with a ceramic cartridge

How to disassemble a two-handle faucet. step by step instructions

To disassemble a water two-handle semi-turnover faucet (Hansa Stela, Vidima, Frap. Frapp) with a cartridge is quite simple, t. к. each drain is connected to a separate lever, it is simple and practical to use. Valve models are most often equipped with special plates that are pressed tightly against each other.

Turning a single valve opens a flow of water of a certain temperature. Rubber or plastic gaskets are used to protect these plates, ensuring that they are sealed against each other and are soft when moving. There are two types of double-lever kitchen faucets:

The domestic herringbone faucet is still one of the most popular types of faucets for the kitchen and bathroom. A feature of this design is the presence in the body of a kind of tee, through which the drain pipes are connected to the lever.

The tap is connected by means of pipes that enter directly into the spout, without the use of additional splitters.

Arrangement of a wall-mounted two-valve mixer for sinks

How to disassemble a faucet with two handles:

  • Modern two-lever faucet can be dismantled only after unscrewing the locking screw, which is located under the decorative panel. But the old Soviet faucet has a more complex design. Here you will need to remove the stop nut, under which is the valve, it is also unscrewed, opening access to the internal parts;
  • Under the screw is a faucet-box, which acts as a valve, it must be carefully disassembled and removed;
  • There is a gasket or ring underneath the faucet-bead, which are necessary to seal the structure. It should definitely be checked for integrity and cleanliness. Even a small speck can cause a leak in the faucet;
  • Assemble a two-lever faucet should be according to the reverse scheme, pre-checking the connection of the pipes and the integrity of the body.

If the body of the herringbone faucet is cracked, it cannot be repaired. This happens most often with cheap Chinese faucets, like Calorie and others.

How to disassemble a two-valve bath mixer

The most common cause of leakage is with cheap Chinese faucets like Calorie

The following are detailed diagrams to be used when disassembling one or the other type of faucet.

Valve faucet disassembly diagram

To disassemble to repair the valve in the kitchen or bathroom, you will need to prepare:

  • Remove the decorative plates from the valve, which indicate the cold and hot water. The plates can be removed by prying with a screwdriver or any other sharp object;
  • under each decorative overlay is a screw that is used to fix the inside of the faucet;
  • then with an adjustable wrench can be unscrewed directly tap head;
  • Depending on the problem, you can remove the gaskets and other elements that have fallen into disrepair from the faucet-bead.

Disassembly technology of a valve-type faucet

The process of disassembly and assembly of the valve faucet is presented in the video.

Disassembly diagram of the single-lever faucet

To disassemble a single-lever type faucet, you need to perform the actions in the following sequence:

  • Use a screwdriver or other sharp object to remove the trim that is located on the lever;
  • Loosen the fixing screw;
  • removal of the control handle
  • removing the fixing nut;
  • unscrewing the lettering.

Disassembly diagram of the single-lever faucet

Shower faucet disassembly diagram

  • As in previous cases, first of all remove the decorative overlay;
  • Loosen the bolt located under the cover and remove the switch;
  • Unscrew the shower head or the cartridge (depending on the type of tap changer).

All work only after disconnecting the water supply in the room. After the repair work and replacement of sealing gaskets, the assembly of the faucets is done in reverse order.

Everyone faces such a problem as a broken faucet in the kitchen or bathroom. In this case there is nothing else to do but to proceed with the disassembly of the valve in order to determine and establish the existing defects. But to perform all the work can only be done by a person who is well versed in the device of the disassembled device. Let’s break down the basic nuances of disassembling different types of mixers.

Ball

To perform the task at hand, it is necessary to stock up on suitable tools. Here you can not do without a wrench, screwdriver, and new rubber gaskets. Now you can proceed to the direct disassembly of the faucet. Before you begin disassembly, it is worth to shut off the cold and hot water supply.

If you have a single-lever faucet in the kitchen or bathroom, you can try to dismantle the lever itself. For this purpose, first remove the decorative cover, and then use a screwdriver to unscrew the screw located under it. To perform this task you will need to make some effort, because most often this fastener is firmly fixed.

Certain ball mixer models may have a lever mounted on the stem. Then it is not necessary to unscrew the screw. You just need to gently push the lever to the up position and then remove it.

The video shows how to disassemble the ball single-lever faucet:

When the work to remove the lever is over, it is worth opening the mixer body lid. It has a threaded connection, as a result of which you can not dismantle the brush with your bare hands. In addition, a connecting screw is used for its additional attachment. First you need to take a screwdriver and remove the lid. After that you can find the clamp nut. To unscrew it, it is worth using a wrench of the required diameter.

If this work is successful, you will be able to find the cartridge in the mixer. It is the one that contains the ball, and there is a rubber gasket underneath it. It is because this gasket is badly worn or deformed, the breakdown of the valve. In case of such a defect, the damaged element must be replaced immediately.

How to disassemble a single-lever faucet in the bathroom and kitchen. step-by-step instructions

Single-lever faucets (with one handle) are the simplest faucets that exist (Damixa Arc, Franke, Oras, Iddis). They are made up of a spout, a swivel lever, a locking nut, a gasket, a replaceable ball or a cartridge.

Disassembling the single-lever mixing valve

Ball water faucet (Gustavsberg, Haiba, Rubineta, Shruder, Varion, Flora) is a type of single-lever. It is used to mix water, it is connected to two pipes: hot and cold. Temperature and pressure are controlled by a ball, which also acts as a shut-off element. The ball is replaceable.

Design of a single-lever mixing valve

Step-by-step instructions with video, how to disassemble the ball single-lever faucet in the kitchen or bathroom:

  • The water supply must be turned off completely before starting work. Otherwise, during disassembly, boiling water may come pouring out of the water supply pipes;
  • Next you need to remove the decorative plug, if you have one;

Pull out the decorative plug on the mixer

After that, unscrew the screw with a screwdriver that holds the rotary knob. This screw connects the handle with the stem of the shut-off valve;

Use a screwdriver to remove the screw

Then remove the handle (control knob) from the body. It is necessary for the water supply and is a regulating part;

Step 4

Next, using a wrench, unscrew the cap;

Unscrew the cap

Step 6

After that you can remove the ball mechanism. You need to be careful, often under the balls are built in springs, which help control the flow and temperature of water. Remove the locking mechanism carefully so as not to damage the fragile springs;

Remove the mixing ball

Using a screwdriver, gently pull out the valve seats and the springs to them;

Step 8

Remove the swivel block of the mixer spout;

Step 9

Any water faucet is equipped with 2 gaskets (o-rings) in addition to the shut-off mechanism, which are often located directly underneath it. They also need to be removed and cleaned. If the gasket has rubbed too hard against the base, you need to pick it up with a thin flat screwdriver or a knife and replace it;

Remove and replace, if necessary, sealing rings

If the reason for the breakdown is that the faucet is simply clogged, for example, with lime salts or other debris, then the repair will proceed much faster. It is necessary according to the instructions above to remove the body and clean it with a special gel. Depending on the material of the spout, you need to choose the right cleaner. They are different for brass, copper and steel. Please note that often the foreign faucet (Italian, German, etc. д.) has a special strainer that goes under the spout. It needs to be cleaned with an old toothbrush and blown out.

Disassembly and repair tips from an expert:

  • Many models (Blanco Elipso, Hansberg Prestige, Hansgrohe, Sentosa, Mofem) are decorated with a special decorative panel. It can only be removed with a thin screwdriver. Lift the lid from the bottom, from the side of the body and carefully lift it up;
  • In case your aerator is dirty, you can drop it in a container with food vinegar for 1 hour to remove various dirt flecks. Before installation, always rinse with water.
  • Ideally, you should buy a complete repair kit for your model in advance;
  • Before disassembling, study the construction of your type of faucet in advance.

How to disassemble a hinged single-lever faucet in the bathtub

How to take apart a faucet with a cartridge

It should be noted that single-lever faucets with ceramic cartridges are now often installed for a washbasin or as a kitchen faucet. They cannot be replaced, so if they break, they must be disassembled and discarded. But in most cases, the faucet with a ceramic cartridge will last a long time, so its replacement is rarely necessary.

Photo. Design of a single-lever faucet with a ceramic cartridge Photo. dismantling diagram of a faucet with a cartridge

And another video instruction on how to disassemble a kitchen faucet with a ceramic cartridge

How to disassemble a two-handle faucet. step by step instructions

To disassemble a water two-handle semi-turnover faucet (Hansa Stela, Vidima, Frap) with a cartridge is quite simple. к. each outlet is connected to a separate lever, it is easy and practical to use. Valve models are most often equipped with special plates that are tightly lapped to each other.

When you turn a valve, it opens a water flow of a certain temperature. Rubber or plastic gaskets are used to protect these plates, ensuring that they are sealed and soft to move. Kitchen faucet with a two-lever mechanism comes in two types:

Domestic herringbone faucet is still one of the most popular types of kitchen and bathroom faucets. The peculiarity of this design is the presence in the body of a kind of tee, through which the drain pipes are connected to the lever.

The spigot, on the other hand, is connected by means of pipes that go directly into the spout, without the use of additional splitters.

Arrangement of a wall-mounted two-valve faucet for sinks

How to disassemble a faucet with two handles:

  • Modern two-lever faucet can be dismantled only after unscrewing the locking screw, which is located under the decorative panel. But the old Soviet faucet has a more complicated design. Here you will need to remove the locking nut, under which the valve is located, it is also unscrewed, opening access to the internal parts;
  • Under the screw there is a faucet-box, which acts as a valve, it must be carefully disassembled and removed;
  • There is a gasket or ring beneath the bucket valve that is needed to seal the design. It should always be checked for continuity and cleanliness. Even a small speck of dirt can cause leaks in the faucet;
  • The two-lever faucet must be assembled in the reverse order, after checking the connection of the pipes and the integrity of the mixer body.

If the body of the herringbone faucet is cracked, it cannot be repaired. This happens most often with cheap Chinese faucets like Calorie and others.

How to disassemble a two-handle mixer for a bathtub

Shower switches

The obsolete ball design is being replaced by piston (spool) switches: eccentric and pushbutton. The first ones are placed in the central bore of the body or separately connected diverter. The second ones are characteristic of single-lever versions; they are located on the spout.

From the central bore the plunger is removed as follows:

  • Disconnect the gooseneck, remove the handle similar to the ball switch.
  • Unscrew the stem connector. Pull it out together with the eccentric stud.
  • Grasp the piston with a small hexagon and pull it downward.

Disassembly of the push-button version, let’s look at the example of Grohe:

  • Disconnect the shower hose.
  • Hold the valve from turning with a screwdriver.
  • Unscrew cap-button.
  • Use hexagon to unscrew the complete mechanism.

Aerator

The aerator is an assembly unit consisting of a cup that combines the filter nets. It is made of brass with male or female threads, cheaper versions are made of plastic.

Salt deposits make it difficult to unscrew, especially from copper-plated steel fakes. It is necessary to use a shovel or adjustable tool, wrapping the cup with a cloth beforehand.

It is not convenient to grasp the small flats on the cup using an ordinary tool. Professionals use special plastic wrenches that allow applying a very high force without damaging the coating.

When purchasing sanitary ware, keep the instructions, which contain a scattered assembly diagram with the designation of the constituent parts. The manufacturers provide technical information on their official websites. Viewing diagrams, assembly drawings will help to understand the device, avoid mistakes during disassembly, repair.

In the absence of information, follow the rules:

  • Dismantle any unit (part), make sure that all obstacles to disassembly or related components. removed, stoppers. released.
  • Do not apply excessive force: quality plumbing is assembled practically by hand. Difficulties indicate missing fixing elements or corroded threads.
  • Reassemble begin in reverse order, with a long break to remember the nuances will help photograph the disassembly process.

Tip! If you need masters to repair your bathroom, there is a very handy service for the selection of experts from PROFI.RU. Just fill in the details of your order, craftsmen will respond themselves and you can choose with whom to work. Each specialist in the system has a rating, reviews and examples of work, which will help with the choice. Looks like a mini tender. Placing an order is FREE and does not bind you to anything. Works in almost all cities you are a craftsman, then follow this link, register in the system and you can take orders.

Author

Goltilar

| Denial of responsibility | Contacts |RSS