Home Washing machines How to connect an Electrolux washing machine correctly
Washing machines

How to connect an Electrolux washing machine correctly

Independent connection of the washing machine

The washing machine must be connected to three networks at once: water, sewage and electricity. Because it is necessary to choose a place for installation so that all three systems were located near or was possible to bring them there. Optimal for the installation of the washing machine are considered to be a bath, toilet and kitchen. they have all the necessary communications. Most often they require a little work, but to connect the washing machine is not very difficult. The process of connection itself is not complicated, you do not need to do anything complicated, if you have “direct” all can be done with their own hands.

There are several places where you can put the washing machine:

The most problematic variant. the corridor. Usually there are no necessary utilities in the hallway. no sewerage, no water. You will have to “pull” them to the place of installation, which is not easy. But sometimes this is the only option. The photo below are some interesting solutions how to put the machine in the hallway.

In the photo. the option of installing a washing machine in a narrow hallway Making something similar to a portal. is also a solution Hidden in the nightstand Build into the hallway furniture

The toilet has all the communications, but in typical apartment buildings the size of this room are such that it is sometimes hard to turn around. there is no place at all. In this case, put the washing machines over the toilet. To do this make the shelf so that sitting on the toilet did not touch his head. It’s clear that it must be very strong and reliable, and the machine. with very good shock absorbers. In addition, they must be perfectly aligned, otherwise it can “jump” when wringing. In general, with this way of installing the washing machine, it will not hurt to make a few slats that will not let it fall off the shelf.

The shelf is solid and reliable, but slippery: you’ll need a rubber mat for shock absorption under the feet. Powerful brackets are embedded in the wall, and the washing machine is placed on them. The plastic stops were removed from the legs, and holes were drilled in the corners for the remaining screws. It’s reliable, but it’s important that the vibration won’t make the corners tear out of the wall. Only the doors are missing

In the bathroom and combined bathroom is usually not a lot of space, but still more than in the toilet. There is a choice. If you have the space, you can put the washing machine near the sink. On top you can install a countertop, which will be a logical conclusion, as well as solve the problem of water ingress on the body. To look all organically, you have to choose such a height of the machine, that it fits the size, and the sink itself is better to be square. then they will become a wall to a wall. If there is not enough space, you can at least part of the body can be pushed under the sink.

To put the washing machine next to the sink Fancy nowadays bathroom countertops can be finished with mosaics If space allows, just put the machine next to the sink

There’s a more compact way to put the washing machine under the sink. Only the sink needs a special form. so that the siphon is installed behind.

To put the washing machine under the sink you need a special sink

One of the sinks, under which you can put a washing machine

The next option for installing a washing machine in the bathtub. at the side of the bathtub. between its side and the wall. Today, the size of enclosures can also be narrow, so that this option is a reality.

Narrow enclosures are no longer rare Between the bathtub and toilet Sink should not be smaller than the enclosure No one interferes with the top to install a sink

Only note, to put in a bath or combined bathroom such appliances. not the best idea. Because of the high humidity, the housing begins to rust quickly (tested by my own experience). However, space is usually not very big, although in principle, you can put the machine under the sink or hang shelves over it. In general, it’s up to you.

Another popular place to install a washing machine is in the kitchen. It’s built into a kitchen unit. Sometimes they close the doors, sometimes not. It’s up to the owners. A few interesting photos. in the gallery.

Doors with a cutout for a “porthole” Place in a kitchen cabinet The washing machine looks quite organic in the kitchen set

Remove the shipping bolts

Before you connect the washing machine, it must be unpacked and remove the mounting bolts and put plugs instead.

The transport bolts look something like this

This procedure is mandatory immediately after unpacking. If you leave the bolts and turn on the machine, it will break. And it’s not under warranty. The number of bolts varies from manufacturer to manufacturer, but the diagram of their installation is in the instruction manual, and on the back wall they are visible. Simply use a screwdriver and unscrew the screwdriver.

Safety Instructions for Using the Washing Machine, Installation and Maintenance, Operating the Washing Machine

Instructions for safe use of the machine

Instructions for safe use of the machine

Парад установкой и началом использования машины изучите внимательно наши рекомендации. Их соблюде­ние обеспечивает надежную работу машины. Все пользователи машины должны знать правила ее эксплуата­ции. Сохраните эту инструкцию на случай, если машину придется перевозить на новое место или продать.

Тот, кто после Вас будет ею пользоваться, должен иметь возможность ознакомиться с машиной и ее функ­

циями, а также с указаниями по ее безопасной эксплуатации.

The appliance is only designed for

in the home; therefore, it must be used exactly as described in these instructions. If the machine is used for other purposes, there is a risk of personal injury and damage to property.

Only a specialist is authorised to install

the machine and connect it to the power supply

open and adjust the mechanism, if necessary.

If you do it yourself, there is

machines. This could result in injury or damage to the interior of the room where the machine is being used

Use of original spare parts. Do not try to repair the appliance yourself!

The fill and drain hoses must lie down

freely, without kinks, and the machine itself must stand on a flat and firm surface

The washing machine may only be used

adults. The machine’s door can get very hot during the wash. Therefore, children must be kept away from the machine when it is operating.

Do not load more laundry into the machine without

Do not overload the machine with laundry. see

Only wash underwear designed for

machine washes. Follow the instructions on the

Bustier bras with “bones” must not be washed in the machine

bones could tear other laundry and damage the mechanism of the machine.

Articles such as coins, nails, hairpins, etc,

pins, needles, can seriously damage

machine. So make sure the s are empty before you load laundry in the machine

items to be washed. Button up all your buttons and

Do not load your stockings, belts, ribbons, etc., need to put in a bag for washing, otherwise during the washing they can get stuck between the tank and drum.

Follow the washing machine’s washing instructions for each load

The washing machine should only be used with a detergent and washing-up liquid. Only use laundry detergents and

Use detergents with normal foam content, i.e., detergents suitable for

Overdosing on detergents can cause serious damage to both the laundry and your machine.

Do not use your machine for dry cleaning.

Do not bleach or color

Your clothes can be stained in the washing machine. items that have been used to remove stains from

If chemicals are used, rinse them gently in water before placing them in the machine.According to the Consumer Rights Protection Law, in the event of a breach of the

and operation, damage caused as a result of such violations shall not be compensated for, claims for defects arising as a result of such violations shall not be satisfied.

Always check that there is no water in the drum. If the water has not drained out, then

follow the instructions in the instruction manual.

water faucet and turn off the main switch (turn off the power). When the machine is not in use, its loading hatch

must be ajar. Then the boot lid seal will not lose its elasticity.

Child safety, Environmental protection, Reuse of packaging materials

Disposal of the machine, Environmental recommendations, Environmental recommendations, Environmental safety, I

electrical appliance. When the machine is in operation

Children should be supervised and not allowed to play with it.

polyethylene film, foam plastic) are

dangerous and may cause suffocation. Keep them out of the reach of children.

a safe place, out of the reach of children.

Make sure that no children get inside the drum

or pets. To avoid this, the machine is equipped with a special device. To turn this unit on, turn the button on the inside rim of the hatch (without pressing it) clockwise until the slot is in the vertical position.

If necessary, use a coin.

To deactivate this device and to make it possible to close the hatch

Turn the button counterclockwise so that the slot is horizontal.

To dispose of the machine, it is necessary to cut off

the power cord and disable the lock

of the boot lid to prevent children from closing the machine.

Materials marked with the symbol can be reused.

To dispose of these materials, it is necessary to put them in special places (or

To dispose of the machine correctly, it is necessary to ask your local municipality for a certificate.

Advice for the environment

In order to save water and energy consumption as well as to protect the environment, we recommend

washing only for very dirty laundry.

the hardness of the water supply, the quantity of laundry, and the degree of soiling.

Use half to two-thirds of the recommended amount of detergent.

Child safety, Environmental protection, Reuse packaging materials

Disposal of the machine

electrical appliances. while the machine is in operation

children must be supervised and must not be allowed to

plastic sheeting, Styrofoam) are

dangerous and could cause suffocation.

the hatch is in a safe, out-of-reach position for children.

Make sure that no children get into the drum

or pets. To avoid this

the machine has a special device.

To turn this device on, turn the

the button on the inside rim of the door (do not press the

the slot will not be in the upright position.

If necessary, use a coin.

turn the button counterclockwise to

the slot is in a horizontal position.

To dispose of the machine must be cut

the power cable and disable the lock

the boot lid of the machine so that children cannot.

To dispose of these materials it is necessary to put them in special places (or

To properly dispose of the machine, ask your local municipality for a certificate.

Environmental Advice

In order to save water and energy consumption and protect the environment, we recommend

Instructions for Safe Use, Installation and Maintenance, Operating the Washing Machine

To give directions for safe operation of the machine

Парад установкой и началом использования машины изучите внимательно наши рекомендации. Их соблюде­ние обеспечивает надежную работу машины. Все пользователи машины должны знать правила ее эксплуата­ции. Сохраните эту инструкцию на случай, если машину придется перевозить на новое место или продать.

Тот, кто после Вас будет ею пользоваться, должен иметь возможность ознакомиться с машиной и ее функ­

циями, а также с указаниями по ее безопасной эксплуатации.

The machine is only intended for

therefore, it should be used as follows,

the machine is used for other purposes, i.e

risk of injury and damage to property

Only a specialist is authorized to install

the machine and connect it to the mains and

also, if necessary, open and set up

If you do it yourself, there are

machines. This could cause personal injury or

the furnishings of the room where the machine is to be installed

try to repair it yourself

the fill and drain hoses should lie down

It must stand on a flat and solid surface

Only use the washer-dryer

adults. During a wash, the loader hatch

The machine can get very hot. Therefore, in

Do not stand near the machine while it is operating

connect, electrolux, washing, machine, correctly

Do not load laundry into the machine without

Do not overload the appliance with laundry (see “Do not overload the appliance with laundry” on page 31). section

Only wash underwear designed for

machine wash. Follow the instructions on the

Busters with “bones” must not be washed in the

the machine, as bones can tear other

Articles such as coins, nails, hairpins,

pins, needles, etc., can cause severe damage

machine. So before you load the laundry in the

check the machine to make sure the s are empty

Washcloths, coins, coins, pennies and other items in the pouch can be damaged. Button up all the buttons and

stockings, belts, ribbons, etc., you need it for your washing

place in the wash bag, otherwise the pips will be torn during the wash

They can get caught between the tank and the drum

When washing the laundry, follow the machine’s washing instructions

Do not overload the appliance with laundry

powders with normalized foaming, then

Overdosing on detergents can lead to

serious damage to both the laundry and

Do not use your machine for dry cleaning.

Do not bleach or stain

If the water has not been drained off, it is very important that you always check that the drum is empty

If the machine is equipped with chemicals, care must be taken to keep the operator’s hands and feet away from the machine

Rinse in water before loading them in

According to the law “On the Protection of Consumer Rights”, in case of violation of the

caused by such irregularities,

You must check each time that there is no water in the drum. If the water has not drained out, then

follow the instructions in the operator’s manual.

the machine is not in use, its loading hatch

be ajar when the machine is in operation. Then sealing

Child safety, Environmental protection, Reuse packaging materials

Disposal of the machine, Recommendations for environmental protection

connect, electrolux, washing, machine, correctly

myPRO. How to install a washing machine with drain pump | Electrolux Professional

electrical appliances. Keep the door ajar when the machine is operating

children should be supervised to ensure that they do not

Polyethylene film, foam plastic) are

dangerous and can cause strangulation.

in a safe place, out of the reach of children.

connect, electrolux, washing, machine, correctly

Make sure that no children can get into the drum

or pets. To avoid this

machine has a special device.

To turn this device on, turn the

button on the inside rim of the door (do not press the

the slot is not in the upright position.

If necessary, use a coin.

Turn the button counterclockwise to

The slot is in the horizontal position.

To dispose of the machine, it is necessary to cut off

power cable and disable the lock

of the boot lid to prevent children from locking themselves in the machine.

To dispose of these materials, they must be placed in special places (or

To properly dispose of the machine, ask your local municipality for a certificate.

Advice for the environment

To save water and energy consumption and to protect the environment, we recommend

Materials and tools for connecting to the water and sewer

The need for certain materials when installing and connecting washing machines to the sewer and water is determined primarily by the location of the unit and the accessibility of designated objects. In some cases, it is necessary to go to deliberately higher costs in order to later comfortably use household appliances for many years.

If you plan to lay additional branches from the plumbing in the hole, you will need a fairly powerful angle grinder with a saw blade on concrete. A hammer and chisel can be used to tap out the concrete.

A pipe without joints is laid in the joint in order to ensure its durability without leaks. Otherwise, if there is a leak, restoring the functionality of the pipe will be associated with a lot of work to find and fix the problem.

To connect to the water supply network is usually used T-piece with a cut-off valve, and to install it in place. a set of wrenches or universal wrench. All threaded connections should be sealed with hemp or FUM tape.

Installing the external branch pipe associated with fixing the pipe to the wall, this will need an electric drill and drill bits on concrete. Plastic dowels are installed in the drilled holes, fastened with screws of the appropriate size.

When installing washing machines the main requirement is the horizontal position of the top cover in relation to the floor. A spirit level is used for precise installation of the washer, the adjustment is done with the screw feet.

To arrange a drain for washing machines in the drainage system will need an adapter for the drain with a branch at an angle of 45 degrees.

To connect the washing machines to the electricity will need a three-core cable with a cross section of 2.5 squares in double insulation and a 16-amp breaker with a leakage current of no more than 30 milliamps.

In addition, it is possible to use control equipment. a voltmeter. How to connect the washing machine to the mains we will consider in detail below.

Preparing the washing appliance for installation

First of all, when the unit is delivered to the place of installation, it must be unpacked. Usually the machine is packed in a cardboard box and strapped with plastic tape. It must be cut open and removed.

After that, carefully remove the cardboard box, and remove the foam pads from the top and sides. Next, you need to lift the machine out of the bottom foam platform.

In doing so, pay attention to its design. if there is no special flange in the middle, on which the drum of the device in the transport position rests, it means that in this design it is made and installed separately. It is necessary to tilt it and remove this insert.

Note that the cardboard packaging and foam gaskets must be retained for the duration of the warranty. If a situation arises in which it is necessary to replace the machine due to a defect, this operation will not take place without the packaging. These are the terms of warranty.

Inside the cardboard box is an envelope or a folder containing technical documentation. It contains:

  • Passport for the purchased washing machine with the personal number of the unit and other accounting data in it. All entries in it should be stamped by the store.
  • The warranty card stamped with the store stamp and the date of sale, because the warranty period starts there.
  • Instructions for use, starting from the moment of unpacking, and instructions on how to install.

All the manufacturer’s requirements should be strictly followed, as failure to comply with any of them will be a reason for denying the warranty.

Threading into the pipe

To connect the technique to polypropylene or metal-plastic pipes, they are cut. At this point we install a metal T-piece. From there we make a branch line to the washing machine. To the sewer outlet connect the device hose to the siphon, which is equipped with a side telescopic nozzle. Attach outlet hose to the appropriate diameter on the branch.

First cut the pipe, measure the size of the tee, cut a piece of pipe. It must fit the transition device. Attach the connection ring with a nut. Flare the pipe ends where it connects to the tee with a calibrator. The tube is put on the fitting nipple and sealing rings are put on both ends. Tighten the nuts securely.

Shut-off valve to the adapter is advised to screw in before tapping. Then the elastic metal plastic pipe will not be damaged. After the tee is connected, the flexible water hoses are attached to the screwed-on faucet.

If you have plastic piping in the house, you will need a special tool to solder pipe fasteners with adapters and fittings. On a pipe with cold water is installed T-piece. To it through the stopcock is connected a hose that supplies water to the machine.

Connection in any place

Sometimes it is more convenient to connect the washing machine in a straight pipe. In order to connect, you need a coupling socket. This is such an adapter in the form of a clamp from a cage with a threaded outlet. Buying it in the store to look at the diameter of the fitting and the size of the pipe match. The adapter, firmly attached to the required fragment, will shut off the water. Then a hole is drilled through the socket of the caretaker. On the branch of the coupling ball valve is screwed. It is used to connect the hose that supplies the washing machine with water.

Connecting automatic washing machine to the sewer with your hands

The automatic machine is connected to the ready outlet of the sewer to solve the problem of draining dirty water. There are two schemes. At a temporary variant use a special hose. With the help of special fasteners fix to the edge of the bathtub, sink or toilet bowl.

Non-moving drain

Permanent scheme provides a device nonmovable drain. It can be made with a siphon in the design, which has a separate outlet under the knee. It serves to connect automatic washing machines. Specialists do not advise using a regular siphon instead, because dirty water will accumulate in it, creating a cork, spreading unpleasant odor.

You can connect without a siphon. If the sewer pipe has a diameter of 4-5 cm, the drain of the appliance is connected directly to this element. Drainage hose, bent letter S, lead into the pipe so that it does not touch the wastewater. It is well surrounded by a sealant and sealed. The distance from the point of bend to the floor should be more than 50 cm. If you take a larger size, the load on the pump will increase, as a result it will fail.

If the design does not include a non-return valve, there is a height restriction on the location of the drain hose during assembly. The manufacturer’s manual provides specific information.

Drainage hose has a diameter of 22 mm, but there is no special socket at the outlets for 32 and 50 mm pipes. A rubber reduction with a 22 mm transition is used for the connection. It is convenient and sealed.

Preparations

Before you buy a new washer, you should determine a suitable location for it. Unlike older models of equipment, modern automatic machines are stationary devices, so they can not be moved, for example, from the bathroom to the kitchen, as they are connected to the sewage system and plumbing.

Most people traditionally define this appliance for washing in the bathroom. Here everything is logical, because this is the easiest room to arrange the drain, and there is a pipeline to which to connect. But in some cases, there is not enough space in the bathroom, in which case the choice falls on the kitchen or hallway. Disguising the walls of the equipment pretty cupboard, you can make quite an interesting object, corresponding to the interior.

First you need to remove the fasteners from the box, which were used to fasten the structure in the truck during transportation. These can be:

Brackets are at the back, holding the hose and electrical wire. Bars, as a rule, are placed between the tank and the body of the equipment. They are easy to pull out by tilting the washing machine forward. Fixing bolts are at the front. They are designed to support the drum. Fasteners after disassembly should be placed in a separate box or bag and put in a secluded place, as they will be needed when contacting the service center. In addition, after unscrewing the bolts in the remaining holes should put plastic plugs that come with the washing machine.

Remember that you should not start the appliance before removing all fasteners. it can lead to unfortunate consequences.

What to do if the machine “jumps?

Most often, increased vibration occurs after the installation of machines. But even time-tested machines can show their “temper” by bouncing and moving around on the floor.

In order to prevent the machine from malfunctioning, the cause of the vibrations must be determined and eliminated immediately.

Strong vibrations may occur in the following cases:

  • You forget to remove the fasteners (clamps, screws) that keep the moving parts in place during transport.
  • Uneven flooring, causing the machine to wobble.
  • The floor is too slippery and level and a rubber mat should be placed on it.
  • The laundry inside the drum has curdled into a lump.

Excessive vibrations can also cause technical reasons, which can only be installed and eliminated by a specialist. Such causes include breakage of shock absorbers, wear and tear of springs, which are used to fasten the tank, weakening of counterweight fasteners, destruction of bearings, etc.

Any of the above causes should be eliminated urgently, as delay is fraught with a breakdown. Confidence in their own abilities and previous experience. good grounds for self-installation of household appliances.

Advice from professionals on how to properly install your own washing machine, as well as clear instructions will help you to do it without mistakes.

Installing a washing machine and connecting it to the water supply

Installing a washing machine and connecting it to the water supply

Before you buy a washing machine, you need to figure out for yourself what type of loading will suit you best and what the overall dimensions should be. You should think about where you will place it: in the kitchen or in the bathroom.

At the moment on the market of home appliances are presented by frontal (narrow, compact, full-size) and vertical machines to install a dishwasher. The equipment, which is equipped with a front-loading, is quite capacious. Vertical machines are also quite roomy and smaller in size.

Now in stores there is a large variety of full-size washing machines. They are designed, as a rule, for a maximum load of 5-7 kilograms of dry laundry. If you have a lot of free space, it is better to choose a full-size model. Such models have many advantages: they are resistant to vibration during spinning, have a large drum, an expanded range of features, and the cost is much lower than the narrow and compact.

Buy a narrow machine with front loading, if you need limited space to install it. If there is no space at all, it is best to choose a compact model and place it under the sink or under the countertop. It is worth paying attention to the fact that the narrow washing machines are designed to handle from three to five pounds of laundry.

The possibility of a large load is also available in vertical machines. In turn, they are smaller in width than the front, which means a decent saving in space. In general, the machine with a vertical load is very convenient to install: it is this advantage and has this format before the other how much does it cost to connect the washing machine. Easy, Comfortable and Free.

Connecting the washing machine to the water supply is made after installing it separately or embedding it in the kitchen furniture. Also popular options for placing compact washing machines under the sink or under the countertop. There is an installation diagram in the manual that comes with the machine. Of course, it is better to entrust this procedure to professionals, because they are qualified and have the necessary knowledge. But for lack of money and time, as well as with some experience, you can do everything with your own hands.

So, you have measured the place for installation, chose a model and paid the price of connecting the washing machine. When you receive your helper, do not rush to sign the receipt at once. Ask to unpack it first as a washing machine machine works. Inspect the washing machine for appearance: no dents, scratches or other damage. Shake the machine there should not be any internal knocks. If you found any of the above, you have the right not to accept this product. If you do not find any defects, you can sign the receipt.

Before installing, be sure to remove the shipping bolts (and rubber plugs). There are either two or four. Not removing the bolts is fraught with vibration and breakdowns. You may need them in the future, so keep them, do not throw them away. Place the machine in the right place.

It is desirable to install the washing machine so that the length of the hose to the drain was not more than 1.5 meters. Because the longer hose requires adapters and clamps. And the load on the drain pump increases significantly, which sometimes leads to its early withdrawal from service.

If one does not make an alignment, then a strong vibrating and moving of the housing is possible, especially when wringing. This factor can significantly reduce the life of the washing machine and bring its owners to despair. A rigid base such as ceramic tile or concrete is required for installation. Coatings such as mats, linoleum and wooden floors increase vibration. If tile will be the base, use rubber feet to reduce noise and vibration.

Connecting the washing machine to the water supply

One of the important design features of the automatic washing machine is that it requires a separate water supply. To do this, you must install a shut-off valve on the existing water outlet, which will shut off the water intake into the washing machine connection Samsung washing machine. It is necessary, because if you connect the washing machine without it, then trouble can occur. The inlet valve can open in your absence and fill the machine, and this threatens a rather serious deluge.

It should be said that some models have an Aqua Stop leak protection. This is such a sensor, which will give a signal to shut off water, in case it gets on the sealed part of the bottom. Service centers have the option of installing an external leakage protection.

It is not a good option to use a sink or bathtub drain with a drain hook. This will make it impossible to use facilities, it is not beautiful, and siphons sinks and bathtubs quite often clogged, which can lead to all the same deluge.

The best way to connect the unit directly into the drain, using a special siphon with a branch for the drain hose of your washing machine.

Now all that’s left is to connect the machine to the power grid. It is better to derive from razvodit new socket and put the circuit breaker stopped working washing machine. It is needed to cut off power in case of overloading.

The final stage of installation will be to conduct an idle run of the washing machine without laundry, but with a loaded laundry detergent. This rinse is necessary in order to clean the machine from the factory grease. At the moment of washing, you will check how fast the water is poured and heated, the noise and vibrations, the drum rotation speed and the water drainage.

At this point the installation procedure can be considered complete. Enjoy it!

How to wash training clothes, Electrolux, Washing machines

The automatic washing machine makes the entire washing process much easier, saving you precious time. However, here, as well as in.

Long gone are the days when appliances were in short supply, and just to get any thing was already a fortune. Buy today.

In the checkroom

The washer can zone the space in a small walk-in closet.

Washer and dryer in the closet. the dream of any housewife.

If you do not want to leave such a large unit in plain sight, buy a cabinet with a lower compartment for the washing machine, and use the upper compartments to store clothes. Match your model to the color of your furniture.

Brown appliances in combination with similar-colored furniture looks just luxurious!

Electrolux washing machine installation

Because of the complexity of many communications and equipment in their installation needs professional help, and washing machines are no exception, but rather a prime example.

connect, electrolux, washing, machine, correctly

How well it’s installed will determine how well the appliance operates and how long it lasts. And the rather high for such equipment should be an additional incentive in the desire to make installation without errors and subsequent rework. Thanks to the specialists of the company GasMontazh, installing a washing machine Electrolux will no longer be a problem for you.

Installation Cost

The washing machine is a complex technique, which you can not just put thoughtlessly, plug it into the socket and make it work. Before installing you need to consider a lot of factors and analyze the conditions. For a good master is not a problem to do all this, and he will easily be able to make the necessary work before the installation itself. And you need to do the following:

The most important thing is the location. The surface must be flat and stable. No need to erect special structures for the equipment, the basic legs will hold the machine securely on an ordinary floor.

In order to avoid system failures and short circuits, the electrician must check the electrical wiring so that there are no problems, and it is suitable for connecting the washing machine. Incorrect wiring can cause critical damage not only to the unit, but also to the entire house wiring.

In addition to the wiring, you need to examine the plumbing system in order to identify a suitable place where you can connect the plumbing. Call a master to minimize the risk of leaks and serious clogs. It’s worth understanding that plumbing is a serious thing and requires a serious approach.

Even with all of the above factors, you need to remember that the technique should have its own place, which you can freely approach, and that the work is not impeded by other objects, especially those that are heated.

Only with the understanding and consideration of all these factors can safely and correctly perform the installation of a washing machine Electrolux. A good craftsman always remembers and makes all these preparations in order to do the job properly. If you do not have the necessary knowledge to perform all these tasks, you need to call a master.

Author

Goltilar

| Denial of responsibility | Contacts |RSS