Home Washing machines How to change the bearing on the washing machine
Washing machines

How to change the bearing on the washing machine

In what order should you perform all the necessary work.

The first thing you need to do is to record step by step, and better yet take pictures of everything you will do when dismantling the washing machine. And without this at replacement of a bearing unit well does not manage. And here write down all it is necessary for that then there were no problems with assembling back. After all, it often happens when you yourself repair this or that appliance, that there are extra parts. We will take the example of a washing machine with front-loading type of laundry.

When replacing the bearings in the washing machine automatic, you will need to follow these steps:

The first thing you need to do is to disconnect the washing machine from electricity, that is, unplug it from the outlet.

Then it is necessary to disconnect the washing machine from the water supply and sewerage system.

Next, carefully, you need to remove two panels back and top of the washer, which of them will be removed first depends on what design of your washing machine, because they are all different.

change, bearing, washing, machine

Then, carefully unscrew the fasteners that hold the control unit, and remove the unit itself.

Open the door of the washer and remove the cuff collar, and carefully tuck the cuff inside.

The next step is to remove the hatch lock.

Then remove all the fasteners that are left, remove the front panel of the washer.

Carefully examine the device and remove everything that prevents loosening the tank mount.

The next thing you need to be very careful, you will remove the heating element of the washer. In some cases it can be left. Removing the heating element, pay attention to the connection of wires, and better yet take pictures, because then you will need to connect them correctly.

After the removal of the heating element it is necessary to remove all pipes, wires, tubes, that is everything that connects the tank and the case of the device, remove the motor.

Following the motor remove the tank with the drum. Immediately after this you can begin to replace the bearings.

To make it comfortable for you to work put the tank on a stable, flat surface, such as a table. Then it will be more convenient for you to replace the bearings.

Replacing the bearing in the washing machine

Replacing the bearing in your washing machine. a procedure that any owner of this household appliance may encounter. When is it necessary to replace the bearings of a washing machine? When you see signs of machine malfunction, namely: a) when working the washer produces a strange sound, or rather hums like an airplane taking off; b) during the operation the “shaking” appeared, and when you move the drum significantly deviates from its axis; c) the drum does not spin at all; d) the washer does not spin the laundry.

With experience in independent repair of household appliances to change the bearing in the washing machine can itself. Before mounting, all tools must be prepared in advance so that they do not become a distraction in the process. During the disassembly of the machine it is necessary to remember the connection of wires to the heating element, as well as all fasteners and connectors. It is best to write down the order of your actions to simplify reassembly. Fasteners vary from model to model, so below will describe only the sequence of manipulations.

How to Change Bearings in a Washing Machine?First, the washing machine should be disconnected from the power supply, as well as disconnect the dirty water discharge hose in the sewer and clean cold water supply. It is desirable to move the machine to the spacious area where there will be enough space for its disassembling and the movement of adults and especially children is limited.

After disconnecting the upper cover and loosen the fastening screws with an Allen key. After the panel get rid of the dispenser housing, and remove the screws, three are located on the housing, and one in the front panel.

Thus, the front panel mounting screws become accessible to you, which you also unscrew.

Remove the hatch, to do this, it is worth slightly pulling the wire clamp.

Dismantle the powder compartment and counterweights, most washing machines have only two.

Consistently disconnect the wires from the heating element, with special attention to their location. It is strongly recommended to write it down, for more safety take a picture.

Heating element is removed, for this unscrew nuts and press a little.

Remove the tube located between the tank and the drain pump. Stock up on a rag, because usually a little water is drained out.

Next, remove the rear panel and the belt, for this purpose turn the pulley slightly.

Dismantle the motor, again mark for yourself the wires, as well as the pressure chamber.

How to Replace Bearings LG Front Load Washer

Remove the tank by first releasing it from the springs with the shock absorbers.

To remove the bearing from the washing machine, turn the drum over and remove the pulley. Prepare wooden slats for the drum, as the pulley must be knocked out.

Disconnect the two parts of the tank.

The washer-dryer bearings are located in the rear compartment of the tank. They are knocked out one by one, but taking care not to damage the seats.

After you have removed the bearing from the washing machine, carefully get rid of dirt, rust and scale.

After disassembly, you can proceed to direct replacement of the bearings in the washing machine. When assembling knock the entire surface of the outer rim of the casing in the same way, without affecting their center The packing must be lubricated before installation.

Next, the reassembly is performed, it should be noted only the back stitching of the halves of the tank. When connecting them, replace the gasket and use sealant. After the seals have dried out make sure they are airtight.

The ex206g2 bearing is a ball bearing which supports the shafts, its housing consists of two rings which are connected by a cage.

Bearing es207g2 is a fixed ball bearing, the bearing consists of two parts. cages, outer and inner, which are connected by a cage, it is self-aligning (housing).

The es208g2 bearing is a ball bearing that is mounted on a shaft, the two parts. cages, inner and outer, connected by a cage, make up its housing.

GE Sealed Bearings.-KRR-B in a wide range with analogues at affordable prices

The cause of bearing and gland wear

The typical rumble is usually caused by excessive wear of the bearings, by means of which the washing drum rotates. Bearing designs vary depending on model, device and manufacturer. The main causes of washing machine bearings failure are corrosion and natural wear and tear. For both vertical and horizontal-loading dispensers, oil seals are installed on the drum shaft or shafts to prevent water leakage. The common material for the glands is rubber.

Gland packing comes in direct contact with water during operation. Detergents combined with high temperature affect the gland, resulting in the rubber loses its elastic properties and the machine begins to leak. Water first penetrates the bearing module. If there is a characteristic noise from the unit shaft. packing. bearing, it makes sense to turn to the experts in their business, masters of washing machine repair for repairs.

The earlier the worn parts are replaced, the fewer problems can be expected. Failure or destruction of a bearing during operation can lead to siltation. This in turn leads to deformation and breakage of mating parts and assemblies.

Replacing the bearings of the washing machine

Squeaking, strong vibrations or knocks are clear signs of bearing failure, and over time the sounds and vibrations will only increase. If the faulty element is not replaced in time, it can lead to complete failure of the washing machine. A complete repair will be very expensive, so it is recommended to make repairs in the first stages.

The main reason for breakdowns is a long service life. It is also possible for parts to fail due to ingress of water (water leads to the appearance of corrosion, which subsequently reduces the life span of the washing machine). The most common cause of water leakage is the stuffing box packing. The average life span of a stuffing box packing is 5 to 7 years. If you want to replace the bearings, make sure you also replace the seals: you save both time and money.

How to Replace a Bearing in an Atlant Washing Machine

Your Atlant washing machine is noisy, humming and rattling? The sound at high revolutions is similar to the rumble of an airplane on takeoff? This tells you the drum bearing is worn out.

The bearing is subjected to heavy loads, so it wears out over time or under the influence of external factors. We will tell you how to remove and replace the bearing in the washer-dryer Atlant. Follow our recommendations and you will be fine.

How to replace the bearing on an Indesit washing machine

When the user notices a malfunction in the CM, as a rule, the breakdown has already reached a medium degree of severity. So also with bearing wear: at the initial stage, you may not notice anything, until the machine begins to work with the sound of a jet engine.

What caused the failure, how to replace the bearing in the drum of the washing machine Indesit, you will learn in the article.

It should be noted that incorrect operation and natural wear and tear are the main causes of wear of moving parts. So that later you can avoid an unpleasant breakdown, let’s list these causes:

  • Overloading the drum with laundry. If your washing machine is designed for a load of 5 kilograms. this does not mean that you need to fill it up to the brim. Correct loading of 2/3 of the drum capacity. Otherwise there is an increased load on the parts, which leads to a rapid breakdown.
  • Incorrect installation of the housing. When the washing machine is not set level, during spinning it shakes strongly, vibration intensifies. All of these adversely affect the moving parts of the machine. Make sure that the washing machine stands firmly on the surface.
  • Wear of the oil seal. Manufacturers claim that the life of the stuffing box packing is on average 5 to 6 years. When the o-ring seals and leaks, water washes the grease out, causing the internal components on the shaft to wear out.

Before replacing a part, pick up a new replacement. So, for models “Indesit” IWSB 5085, IWSC 5085 can go bearings with different serial number. To understand what suits your SM, look at the table.

You can find out how much the repair kit costs on the Internet or on the manufacturer’s website. It is better to choose original spare parts. They will fit your model exactly. They come with 1-2 bearings and a gland. Replace all elements at once, otherwise there is no point in carrying out repairs.

The wear and tear of the moving parts on the shaft is difficult to confuse with something. Its companions are squeaking and grinding when the drum rotates. The back of the tank may show signs of wear and tear. Begin disassembly.

Replacing the bearing in the drum of the washing machine Indesit with their own hands

Before changing the part, prepare for disassembly. What tools are needed:

  • Phillips and slotted screwdriver.
  • Open-end wrenches.
  • Torx sockets and wrenches.
  • Wooden bar.
  • Chisel.
  • Pliers.

WD-40 liquid is also helpful. It would help you get rid of the stuck fasteners.

Indesit washing machine bearing replacement involves complete disassembly. You need some space for this. If you can’t bring the machine into the garage, put it in the center of the room.

How to Replace Washing Machine Bearings

  • Pull the plug out of the socket by unplugging the machine.
  • Turn off the water valve.
  • Disconnect the fill hose from the body. Immediately lower it into a sink or container to drain the water.

Place the water supply valve in the center of the room. Take out the powder dispenser, because moisture residues accumulate inside it. Also pull out the drain filter.

This is located under the door. Wait for the liquid to drain out and proceed to disassemble the Indesit IWSC 5105, WISL 102.

Dismantle the top cover by removing the two screws from the back. Slide it back, put it aside.

  • Unscrew the screws fixing the control panel. Leave it hanging from the wires or lay it on top of the case.
  • From the back, unscrew the solenoid valve bolt. Pull it out together with the detergent tank. At the same time unfasten the clamp of the spigot and remove it from the seat of the tank.
  • Disconnect the interference filter by twisting off the rear fasteners.

Go to the back cover of the model Indesit WISL 103, WISL 83 or other.

  • Disconnect the heating elements. It is not necessary to remove the part. But you can do this to clean the heater from the scale. Unscrew the central nut, press the bolt inside and take out the heater.

Turn the machine sideways. In advance, you can put an old blanket or towel on the floor, so as not to scratch the case. Bolts of shock absorbers are attached to the bottom. Unscrew them.

  • Disconnect the terminals from the pump.
  • Unclench the clamp of the drainage pipe, pull it off the tank. Water has accumulated inside, so point the spigot into a container or on a towel.

There is nothing else attached to the tank from below. Put the machine “on its feet” and switch to the front wall.

Dismantle the front panel, beginning with removing the sunroof collar clamp.

  • Remove the UBL screws.
  • You can immediately put your hand behind the enclosure and pull out the LOS wiring.
  • Remove the fixing screws around the perimeter of the wall. Lift it up and remove it.

Soon we come to how to pull out and replace the bearing in the Indesit WISL85X, WS84TX washing machine. In the meantime, take the tank out of the housing. Lift it off the springs.

Features of the disassembly of the tank. This element in the washing machine “Indesit” is indestructible. Place it on the rib, prepare a metal hacksaw. There are a few sawing features that will help you assemble the halves tightly later on:

  • Sawing is carried out from top to bottom first to half. Then go back up and saw the other half again.
  • Set up the hacksaw so that it is absolutely level. If you place it at an angle, it will leak.

Before you start sawing, mark out the places for the future holes. There you will then place the self-tapping screws to hold the two parts together. Drill holes of suitable diameter with a drill. Read more about how to saw the drum in a separate article.

After removing the upper part, proceed to remove the pulley.

This is necessary to get the drum out. Block its rotation with a wooden bar. Use a wrench on the center bolt and unscrew it.

To dislodge the drum, tap the sleeve with a rubber mallet.

How to remove the bearing from an Indesit washing machine?

  • Place a chisel on the outer ring. Move it crosswise and crosswise and tap with a hammer.
  • There are two parts to be knocked out: the inner and outer.
  • After that, clean the seating area of scale, dirt, workings out.

Insert the part from the repair kit into the housing. Using the same technique as for disassembly, hammer the bearings into place.

The stuffing box is placed on top. Watch the video of carrying out the work:

After the work is complete, reassemble. After installing the drum, lubricate the edges of the drum with sealant. Screw them together tightly. Then screw the self-tapping screws into the holes provided.

Sometimes you need to replace the motor bearing in your washing machine. You can tell a breakage by a poor rotation of the motor rotor. During operation a scratching or creaking sound is heard. This means that the moving parts are worn out and need to be replaced.

How to Change a Product? To disassemble, you’ll need pullers. You can buy them in a store, but make sure they fit the size of the shaft. Install the puller and pull the ring out of place. To make the task easier, lubricate the mount with WD-40 liquid.

The new part is driven evenly onto the shaft.

That’s it. The work is painstaking and requires skill in repairing. But there is nothing difficult for a person with good hands. Good luck!

Necessary tools and details

For this task we need to almost completely disassemble the washing machine. And of course we need tools. What exactly do we need?

How to Change the Bearings in a Washing Machine

  • Pliers.
  • Screwdrivers (slotted and Phillips).
  • A special screwdriver with various bits.
  • The round pliers.
  • A set of wrenches of various sizes.
  • Waterproof sealant.
  • A chisel (blunt).
  • Rubber mallet.
  • A big ordinary hammer.

We also need oil seals and bearings. You can buy them at various service and specialty stores. If you do not know any of these organizations, then just type in Yandex, Google or another search engine: “Buy bearings for the washing machine” to this query is better to add the name of your city. For example, “buy bearings”. In the search engine you can find companies that sell parts. Give them the make of your machine. After that they will inform you about the cost of spare parts. As a last resort, you can first remove the old parts and then pick up the exact same new ones.

Replacing the bearing in a front-loading washing machine

The element is replaced in accordance with the manufacturer’s recommendations or when there is extraneous noise, squeaking, vibration or leakage. To change the parts yourself is possible only by strictly following the instructions, tools and experience, because you have to disassemble almost the entire washing machine, regardless of manufacturer, in order to get to the tank and remove the drum. Traditionally, in models with front-loading installed 2 elements, which are not serviced, they are replaced with the subsequent disposal.

Availability of a puller will greatly simplify all activities, in the absence of a device. Use a brass hammer and chisel. Blows should be applied on the top cage carefully enough to avoid skewing, deformation of seats and damage to other nodes.

After disassembly, should make a thorough cleaning of the oxidation, dirt, check the other components for performance.

Author

Kerariel

| Denial of responsibility | Contacts |RSS