How to assemble the handle of the Beko washing machine

Do.it.yourself repair handle repair with your own hands

A typical situation. the castle has broken, and the linen remains in the drum. There are several proven ways to open the hatch:

• Emergency opening. Modern models of the grease are equipped with a special lever or cable. It is usually located in the area of ​​the drain filter. Pull the device down. the hatch is unlocked.
• Open the lock from the inside. You have to dismantle the top cover to reach the hatch lock.
• Using the tool. If the plastic part breaks, use the pliers, a screwdriver to activate the remnants of the mechanism.
• Rope, lace. Squeeze the tourniquet between the hatch and the case for the perimeter of the opening, pull the ends.

Before using the emergency opening of the washer, make sure that the washing program is over, the machine is disconnected from the mains. The problem is eliminated. proceed to repair.

Hydrogen peroxide processing

With this tool, you can not only disinfect wounds and bleach hair, but also withdraw ink. A small amount of a 20 percent concentrate of hydrogen peroxide using a cotton pad or stick must be applied to the processed area. If this composition is not available, then you can use the mixture of hydraetite. 4 tablets of substance per 50 ml of pure water will be required.

After removing the pollution, the processed place must be thoroughly dried with a napkin, the structure of which is absorbed in an ink paste and stain. If the inscription has not deleted the first time, then the procedure needs to be repeated. Should not be too much pressure on the paper, otherwise it can be damaged. You need to act as accurately as possible.

External damage

The castle may not be closed due to ordinary wear or careless circulation. For example, sometimes wet things are hung on the door, which can damage the mechanism with their weight. Damage can also occur if you close the unit with excessive effort.

The device may not close for several reasons:

• As a result of prolonged use, the door of the washing machine was skewed.
• The tongue in the lock mechanism intended for fixation was displaced.
• There was a wear of a plastic element or rubber gasket.

Identifying a malfunction of this type is not difficult. To check, you can make test closing in normal mode, without loading underwear. If the door does not close in such conditions, then there was a breakdown of the lock, or the mount is skewed. Sometimes this may be due to the wrong installation, and then in an uneven position the hatch can be pumped under the influence of weight and vibrations. How to install a washing machine correctly. read here.

You can debug the work of the machine on their own. Carefully inspect the device and the castle mechanism. Check:

• Does any closing items interfere with. Sometimes things can completely or partially fall under the hatch and jam the operation of the system.
• Court’s condition: whether it gets into the groove.
• Is it a fixing tongue.
• Signs of plastic peeling or rubber laying.

Crochet problems

The car door is shocked, which ends the shutter core. It is this hook that should stand in the nest and fix the structure. As a result of wear, vibrations and other factors, the supporting rod can move out of its place and at the time of closing do not fall into the nest. The door may not close or close, but the closing sensor will not work.

You can solve the problem like this: dismantle the hatch door, spin it around the perimeter. Reveal the details of the hatch, set the base of the hook in place and collect everything in the reverse order.

Sagging of the door of the hatch

Doors frame is usually made of plastic. All fasteners (loops) are made by metal. Plastic is softer than metal, and over time it is abrasion and deformed at the contact site. As a result, the hatch door can sag, as a result, the lock hook does not fall when closing where it should be. In such a situation, it is necessary to change either the entire door or fasteners. You can do this according to the following algorithm:

Over time, the hatch door can sag

Damage to the door handle

The assembly lock mechanism consists of the following elements: handle, lock hook, lock rod, spring. The breakdown of any part leads to the fact that the door is not blocked or does not close/opens.

According to statistics, the door handle most often fails, as it is subject to the most active effect on the side of the user. To replace any of the listed parts, it is necessary to disassemble the entire door and replace the handle.

• unscrew the door;
• disassemble it into the components;
• dismantle the old pen;
• install a new part;
• assemble the door, install it in place.

Causes of breakdowns of a washing machine castle

Most often you have to face the fact that when trying to close the door, it is simply not fixed in the right position. Usually we hear a characteristic click that simply cannot but notice. If this does not happen, then the UBB will not work and the washing machine does not start.

There are several reasons that can lead to a malfunction of the Washing machine door:

• Doors skew over time;
• mixing a fixing tongue in a castle mechanism;
• wear of the plastic component or rubber seal.

As a rule, there are no special difficulties with diagnosis. If the door does not close in a normal state without linen, then, most likely, the latching mechanism (ubble) itself was damaged or a distortion appeared.

Sometimes washing machines are installed not quite evenly, so the glass hatch under the influence of attraction and shaking can be pumped. Similarly, the lock of the washing machine can be damaged.

Washing machines with a display report problems with the hatch lock using an error code. For example, on Samsung cars (De, Ed, or Door), LG. Electrolux (E40), Ariston (F17 or Door).See also. how to check the TEN of the Washing machine with a multimeter

Replacing the door of the lamp of the washing machine

Damage in one way or another affect the work of technology, which is why now we will list the main signs by which we can recognize it. It:

• Constant puddle formation in front of a washing machine.
• Luke’s leakage.
• Cracks formed on the glass that pass water.
• Loose closure of the door, the consequence of which are constant leaks.
• Unstable position of the handle (it staggers).
• The inability to close the door to the end.
• Creak or crack when using a handle.

If you have something similar, then you should urgently start repair.

Replacement of the uble of the washing machine

After the hatch is open, you can proceed directly to the replacement of the lock.

• Remove the cuff from the front wall of the case. In some models, for this, you need to pick up a spring with a flat screwdriver on which the cuff holds, and then remove the fixing clamp. In other types of locks, round.drawers or pliers may be needed to solve this problem.
• After the cuff is dismantled from the front wall, you can get to UBB.
• Unscrew two external screws that provide locking lock. They are placed on the site where the key hook penetrates the locking device.
• Now the uble can be removed through the hole between the body and the cuff.
• After that, the wiring from the failed lock should be disconnected. Instead, connect a new, fully functioning locking device.

• Then install the lock in the place intended for it and fix it with screws.
• Put on the cuff, fix it with a clamp.
• After that, install the door, in the reverse order performing the same actions that you performed in the process of dismantling.

All is ready! You can carry out a test launch of a washing machine. Now you know how to replace the lock of the washing machine. Thanks to our instructions, you can repair the device yourself without spending funds to specialist services.

How to dismantle

To change the handle, the door from the machine needs to be removed and dismantled the broken part.

Important:

Before disassembling the door, it is necessary to remember the location of the bolts, the place of fastening the handle and the side of the glass of glass. Better to photograph it so as not to forget.

It is not difficult to carry out dismantling yourself, without the help of the master. The instruction is very simple:

• Open the door. Near the canopy, find the attachment places to the body. As a rule, these are self.tapping screws that can be unscrewed with a cross blade.
• Remove the cover of the bootable hatch, put on the floor. It will need to be disassembled.
• Spin the fasteners around the circumference of the lid. This will require a regular or cross screwdriver, depending on the type of fasteners.
• Insert a flat screwdriver into the gap between the inner and outer part, subtract. Disassemble the door into two halves, remove the glass.
• The handle is fixed with a metal rod. It is required to press on it with an awl or a thin pin, push and hook the rod, then pull out.
• Get a pen and spring.

Advice:

The place of fastening the handle is best photographed before dismantling, so as not to get confused during the assembly.

How to install a new pen

The pen should be purchased at the store of household appliances. Going for a purchase, you need to rewrite the model and name of the machine so that the new part is suitable. It is equipped with a spring and a rod necessary for fasteners.

• Insert the spring. It needs to be put on the same place where the previous. At the same time, it is important to observe attentiveness. The spring should be exactly in place. It’s quite difficult, you need to try.
• Insert a hook with a handle until it stops.
• When the part took its position, insert the pin. It needs to be passed through all the holes. While pushing it should be rotated to facilitate entering the hole. You can use the pliers.

Having dealt with the problem, you should check if the pen works correctly. Because of the spring it is a little forth back. If the handle is not repelled by the spring, it is not inserted correctly. It is better to immediately disassemble it and try to insert it again.

Next, you need to place the glass and put the second half of the lid to a characteristic click. Fix the halves with fasteners and install the door on the machine.

Advice:

If you can’t deal with the replacement of the handle yourself, it is better to call the master so as not to damage the details.

Site editor.in.chief. I understand the topic of equipment, 10 years of experience in large retail chains. The team of the Technician team is written on the team and expert materials. There are many third.party authors on the site, but I am responsible for the reliability of information in the collections.

The algorithm for repairing the lock of the washing machine:

Even in good washing machines, the plastic deteriorates over time due to the dismissive use of the device. When breaking the support, the hatch may fit loosely, provoking the risk of flooding. If this part is spoiled, remove it and fix it with the damaged part with a vice. The diameter of the nail should be 4 mm. Cut it to the desired length if it is different.

Drill a through hole in a size of 3.8 mm in the support. Hold the nail with pliers and heat up to 180ºC. After that, insert it into a drilled hole and wait 3 minutes while the nail cools. It remains to assemble the door and install in place.

Repair of damaged glass

Damaged glass is more difficult to repair. Here you need the use of polyester or epoxy resin. After removing the door, you should consider the possibility of taking off the glass. Most often it is not removed. Therefore, they repair it like this:

• Polyethylene film is glued to the front surface. You may need to use adhesive tape. The cracks are unacceptable.
• On the available hole requiring sealing, they lay a reinforcing tape (it is used in plastering).
• In a separate container, according to the instructions, the resin is prepared. Mix the base and hardener in the right proportions.
• After preparing the resin, it is poured into the right place.
• Usually polymerization occurs within 24 hours. After this time, a polyethylene film is removed.
• With the help of sandpaper, the sneakers are removed.

This is how the glass on the door of the washing machine is easily repaired.

The natural reasons for blocking the hatch of the washing machine

In fact, if the door of the washing machine does not open, then there is no reason for concern. after all, the reason can be completely natural and be an integral washing process.

Blocking during washing every washing machine after you launched the washing program, locks the door “on the lock” or, to say otherwise, blocks it. This is done with the purpose of safety: imagine what could have happened if there was no such lock, and you or your child during the cotton washing program at 90 ° would come and open the door! The whole number of “boiling water” would have poured on your feet or your child, the consequences would be just terrifying. It is for security reasons that such a blocking is necessary. Therefore, if you have a washing program, then the door simply cannot be opened and therefore it is worth blocking. If you still want to open the loading hatch, then first stop the washing program.

Blocking after washing if the washing program is over, and the door still remained locked, then do not panic-most washing machines do not open immediately at the end of the washing program, but after 1-3 minutes. This was done, again, from security goals. Imagine the situation that you pull out a washing machine from a rosette during spin and instantly open the door, after which you put your hand into the drum that still rotates by inertia. It is possible to get a serious injury.

The second reason for such a lock is that the drum heats up during washing from high water temperature, the lock is heated along with it. If you open it right away, then you can burn yourself, so the lock must cool. If your washing program has just ended and the hatch is blocked, then wait a while (usually 1-3 minutes) and try to open it again.

If after the opening of the hatch you found that the linen in the typewriter remains wet, then you have problems with an exalgage in the washing machine. Why doesn’t the squeeze in the washing room and how to fix this problem you can find out on our website.

The door is blocked due to the shutdown of electricity

If the door of the washing machine does not open after there was a jump in the house or completely turned off the light, then do not be upset. This situation occurs quite often, and manufacturers have provided the ability to protect you in the event of a power outage. Imagine that you turned off the light, you did not notice it and thought that the washing machine just finished the program. The consequences of the opening of the hatch in such a situation can be quite unpleasant and dangerous: water will result in you or when the electricity is supplied, a new washing cycle will begin, and you at this time unload the laundry.

For the door to open, you need to start some program again after the power supply of electricity: you can just run out or drain the water.

After this procedure, the hatch will be unlocked.

Dismantling and repair of the washing machine “Beko

The screws are rotated by 90 ° to the left, fixing the panel, and remove it.

Front Panel

• By pressing the opening button of the hatch door, open the hatch;
• With the help of pliers, the clamps are removed with which the hatch seal is fastened with the front panel;
• Separate the hatch of the hatch from the front panel;
• Two screws are turned away, with which the hatch door is attached to the front panel (pos. B in Fig. one);
• Remove the lower decorative panel;
• They turn off the screws with which the front panel is attached to the case of the machine;

Luke door

Inner rim of the door of the hatch

Luke glass

The lock of the castle

• Remove the door of the hatch and the inner rim;
• Two screws on the inner rim;
• Remove the click of latches from the axis on the inner rim of the door.

The loop of the door

Two screws are turned off, which attach the loop to the front panel (pos. C in Fig. one).

Handles of thermostat and ka

Both handles are removed by pulling them over (with reverse installation, attention should be paid to the position of the thermostat axis).

Detting distributor panel

• Put forward a bunker for detergents;
• By pressing the siphon, they remove the bunker completely;
• Turning up the bunker, remove the panel, pressing the fixing latches with a screwdriver.

Control Panel

• Extract a hopper for detergents;
• Remove the handles of thermostat and ka;
• They turn off the screw fixing the control panel (pos. A, Fig. four);
• Remove the control panel from the clamps attaching it to the load.bearing panel.

Carrying panel

• Remove the top cover and control panel;
• They turn off the screws fixing the detergent distributor, disconnect the electric wires suitable for the load.bearing panel;
• Take 6 screws fastening the carrier panel to the case, and remove the panel.

Command.apparatus

• Remove the top cover and bunker for detergents;
• Remove the handles of thermostat and ka;
• Remove the control panel;
• Turn the screw on the axis of the ka;

Thermostat

• Remove the top cover and bunker for detergents;
• Remove the handles of thermostat and ka;
• Remove the control panel;
• Two screws are turned off with which the thermostat is attached to the load.bearing panel;
• They turn off the screw with which the tourniquet of the wires is attached. Removing clamps from the burning, release the capillary tube. Extract a flab of a thermostat from a nest in a tank (pos. A, Fig. 7).

Level relay

• Remove the front panel;
• They turn off the screw with which the tourniquet of the wires is attached;
• They turn off the screw with which the level relay is attached (pos. B in Fig. eight);

Speed ​​control module

Buttons

• Remove the top cover and bunker for detergents;
• Remove the handles of thermostat and ka;
• Remove the control panel;
• Remove buttons;
• Extract buttons from nests on the supporting front panel;
• Disconnect the wires.

The scales of the command.control and thermostat

(With the reverse installation, the scale is put into the latches and rotated so that the recess in the posterior lower part of the scales is directed down. In this case, the handle of the thermostat or ka is rotated so that the slot on the handle is directed upward. Attention should be paid to the correct installation of scales.)

Normal filter

• Remove the top cover;
• Disconnect the wires from the noise filter;
• Two screws are turned out in a plastic box located at the posterior wall of the case of the car, which is attached to the intercoming filter;
• Remove the filter, loosening the pin M8.

Solenoid valve

• Remove the top cover;
• Disconnect the wires from EC;
• Move back the clamp on the EC hose and remove the hose;
• By pressing the screwdriver on the latch, which fixes the valve to the machine body, turn the ec counterclockwise and remove it.

Luke door lock

• By pressing the opening button of the hatch door, open the hatch;
• Remove the clamp by which the hatch seal is fastened with the front panel, and separates the seal;
• Two screws are turned off with which the lock is attached to the car body (pos. A, Fig. one);
• Remove the front panel;
• Remove the cable from the castle (pos. A, Fig. eight);
• Take out the lock from the nest;
• Disconnect the wires.

Trick of Luke’s castle

• Remove the top cover and front panel;
• Remove the clip of mounts of the sleeve along which the castle wire passes;
• Pulling down the tire pulling off. Unhook the cable from the castle;
• Squeeze the plastic latches of the lock and stretch the cable.
• Remove the front panel;
• Disconnect the wires (pos. B, Fig. 7);
• Weaken the tightening of the Bolt M6 and remove the heater from the tank cover (pos. C, Fig. 7).

(With the reverse installation of the heater, it is necessary to ensure that it falls into the fixing bracket.)

Instructions: what to do if the door of the washing machine does not open

Models are on sale in which an emergency cable is built, due to which emergency opening of the door is carried out. If you still fail to get into the car, since the door does not open, and the above methods are already tried, then you can try to open manually.

Before opening a locked door, it is worth studying the advice of specialists

The cable is placed on the front panel near the drain filter. To bring the part into action, just pull the cable. If the cable is absent, then the upper panel is removed, for which the element is unscrewed using the screwdriver. As soon as the panel is removed, the machine leans back to shift the drum from the location, after which you need to get it and take it aside the latches, due to which the lock is removed.

How to remove the hatch yourself?

To repair and replace any part of the door, the first thing you will need to remove it from the mounts. To do this, perform a sequence of actions:

• First disconnect the door with a loop from the device case. For this purpose, remove the clamp and the cuff, pushing them with your hands or a flat screwdriver to bend the loop and fix the fasteners of the screws holding the loop;
• Twist the bolts fixing the loop with the body of the washing machine, then you can disconnect the door along with the loop from the main body;
• Depending on what part you need to replace, separate the loop from the door, so you will get access to the replacement of most of the elements of the hatch (latches, glass, lock).

Depending on the model of the equipment and the manufacturer, the configuration of the door mounts may vary. Some manufacturers fasten the door with only a few self.tapping screws, and some will need to perform more complex actions to disconnect the door from the device case.

So, having familiarized yourself with the material, you can independently replace the main details of the door of the washing machine. Follow the instructions for the operation of the equipment and handle it carefully, so you can significantly prolong its service life.