From the gas stove smells of kerosene

What to do if the gas stove misses gas: the reasons for the gas leak and their elimination

We are sure you have heard more than once a pungent smell from fireplace. The stench does not mean that the gas stove misses gas. what to do in such a simple situation, you probably know. The first actions during gas leaks are taught at school, but your children and your children will be better if you get acquainted with this in more detail.

Critical situations are also not uncommon. The probability of an explosion is reduced as the tenants will find the place of leakage, eliminate its cause. You need to study this sphere, if only in order to completely exclude the risk, is it so?

If you read the article, you can determine one or two signs to determine the cause of the fuel leakage. In a short period of time, you will prevent the worst scenario. Separate actions require the intervention of gallmakers and masters, and something can be repaired independently. Find out what exactly.

Why gas stove misses gas?

Gas stoves consist of many tubes and nodes. Any threaded joints lose their density over time, and a certain amount of fuel will seep through them. The functionality of modern plates protects against many unpleasant moments, but even they miss gas. If you constantly use household tools, then effectively and relatively quickly eliminate the leak.

The traditional gas plate has a hob with burners (burners), control handles, a lattice, a lid and oven. The work of the equipment is affected by the correct installation, details, and the build quality. Due to breakdowns and problems with equipment, gas can partially exit.

The gas stove consists of a hob with burners, an adjusting panel with handles and oven, and the gas enters the equipment through a supply tube

The owner should find out where exactly:

• through the burners and their nuts;
• pens that control the burners;
• shut.handed crane of a gas stove;
• hose or place of its connection;
• internal elements.

The problems are brought to the problems of the unauthorized installation of plates, which is prohibited by the safety rules. For old gas plates, a certain violation of insulation is the norm. It is better to replace or repair the technique through the service center. A faulty slab in the state cannot be left unattended. You can rely on built.in protection, but only for a short time.

Consumers are faced with leaks if there is not enough lubricant in the valve’s traffic jam or the tap itself was exhausted. The nuts often weaken and the seals wear out. It is not easy to solve such difficulties, but internal breakdowns also cause great difficulties.

They simply stop using a faulty burner if it is not possible to repair or replace a new. Gas output through the burners occurs when the stove is inappropriate. For example, if you serve liquefied gas in the device for the gas network.

A strange gas was launched into the apartments of Kiev

Kievans recently began to notice that something was wrong with gas in their dwellings: an unusual pungent smell comes from the plates, and they have to cook on it longer. The color of fire over the burner often changes from blue to orange or red, reports Vesti-Ukr.com. Experts say that the gas does not receive high.calorie and low.quality, as a result of which it does not completely burn out and it has to be spent more. In Kievgaz, they assure. nothing has changed.

“I began to notice that when I cook, the apartment began to smell strongly gas. Not so much with a standard smell, smells of kerosene. And the flame itself is like liquid. You need to give a large pressure of gas to boil the kettle. It can be warming up for a very long time, ”complains Tatyana Ryabak, who lives on the street. Kudryashova.

“Made repairs. There is a new slab. There are no complaints about her. Gas does not poison, but when I cook, it stinks terribly. The wife complains that even the smell comes into the rooms. Well, the flame is not blue, as before, but has a red-yellow tint. Warm has become worse. A two.liter kettle boils in more than 15 minutes. And this is with powerful gas pressure. That is, we began to spend more, the counter is considered to be. Feeling, as if it is diluted as at gas stations, ”said a resident of Rusanovka Andrei Buvolenko.

Kievgaz assures that they have not changed the composition of blue fuel. “Dodorization (additive for smell Ed.) Gas is carried out in Kyivtransgaz, in the boyar, the norm of odorization. from 12 to 16 grams per 1 thousand. cube. m of gas, ”says the chief engineer of Kievgaz Oleg Structure If the gas is more sharp, then the amount of odorant corresponds to the upper scale of the norm. The odorant does not harm people’s health, there is nothing to worry about. It is added more, for a better determination of the leakage.

Experts do not agree with the words of an employee “Kievgaz”. Member of the College of the State Agency for Energy Savings and Energy Efficiency Maria Yakovleva says that it directly depends on how long you will stand at the stove: “If you see a red light, this means that gas has low heat transfer or calorie content. Standard gas is blue and has high heat transfer, so the dishes are cooked quickly. Red is low.calorie gas, so it has low heat transfer, the dishes are prepared slowly, and as a result of gas it is consumed more. This can be explained by the lack of normal control when the gas intake into the system “. According to her, red gas contains a lot of nitrogen. “It needs to be mixed with methane, brought to the minimum acceptable, and these are high costs. They save on this. As a result, the population is very overpaying. at least three times “.

Join the telegram channel of truth.Ru with the ability to express your own opinion)

Add the truth.Ru “in his sources in Yandex.News or News.Google.

Independent diagnosis of malfunctions

To figure out whether the gas smells from the oven or from the stove, it is necessary to determine in which place the leak occurred.

Having determined where there is a gap, it will be easier to describe a malfunction when calling a specialist. This will help the master take the necessary spare parts for repair.

If there is an unpleasant odor in the room, it is important to deal with the nature of the malfunction:

• gas enters the room, even when the stove does not work;
• An unpleasant odor appears after the device is turned on;
• gas oozes from turned off fireplaces when the neighboring work;
• An unpleasant aroma appears only while setting on the stove.

Most of the defects are eliminated by replacing the tightness of the hose, worn over the laying of the part. However, it is better to entrust work to restore the working capacity of the plate to professionals.

You can determine the cause of the malfunction of the gas stove in several ways. In the process of diagnosis, it is important to comply with safety regulations, not to allow children to a faulty device

When it is found that the gas panel misses gas during operation, it is important to quickly find the leakage site.

You can independently determine it in several ways:

• By ear. a characteristic whistle appears in the place of depressurization.
• By smell. unpleasant aromas intensify as we approach the leakage site.
• Visually. to determine the place from which the gas comes out, use soap foam. For this, soap is diluted with warm water. Thick foam is applied to the joints of the hoses, pipes, taps, threaded joints. When the device is turned on, soap bubbles will appear at the leakage site.
• With the help of specialized attires. Compact devices analyze the composition of the air. In case of serious deviations, a sound signal is made, and some models equipped with a valve-mecrrator are blocked by gas flow.

When the presence of gas leakage is confirmed, and its place is found, it is important to ventilate the room well, to report a malfunction in the gas service.

You can not look for a place of gas leakage using a lighter. If the gas has accumulated inside the slab, such actions can cause an accident

While you expect gas service specialists, it is not recommended to use electrical devices, turn on/off them.

Elimination of gas stove malfunctions

Before starting the repair, it is important to know that all gas reinforcement is made of their alloys that do not give sparks in contact. In the process of recovery work, it is worth using similar materials.

Passatigi, a divorce key for the slab and valve, gas key will be necessary from the tools.

Problem #1. burning malfunctions

When the smell of gas appeared as a result of the extinguished flame, it is necessary to immediately close the valve, ventilate the room. A similar situation is considered an emergency case, so you need to immediately open the windows wide open. When the burner cools down, it is important to thoroughly blow it, clean it from food residues, fat.

During the operation of the stove, a carpet accumulates on the burners, which can give the flame a yellow tint. This can be misleading, creating the appearance of a malfunction where it is not.

Serviceable burner provides a flat flame of blue color. If the tongues of yellow, red skip, this indicates a malfunction of the burner, the probability of fuel leakage

After thoroughly cleaning the burner, it is necessary to install it in place, light, check the performance

If any defect is the cause of the malfunction, it is worth replacing the burner with a new.

Problem #2. breakdown of the connecting hose

The hoses used to connect gas are sold at specialized retail outlets. Visually, they differ from the rest of the bright yellow shell.

Gas supply hose, connecting elements, differ in bright yellow braid. This allows you to highlight the elements suitable for creating a gas pipeline from another similar product

When the cause of the leak was a crack in the hose, it is worth replacing it. After all, the repair will provide a short.term effect and the unpleasant odor will appear very quickly again.

Problem #3. leakage in the area of ​​the locking crane

To check the operation of the node, it is necessary to apply a soap solution to the pipe. If a leak is detected, you need to immediately block the gas supply, call professionals. In the presence of a new valve, linen pack, the master will quickly replace the gas crane.

At the end of the installation, the connection is delayed until the valve rises to the desired position. The correct installation is determined by repeated application of soap solution.

The shut.off crane is located on a pipe connected to the central line. Also, the problem can be in the valve at the site of connecting the stove to the cylinder. In case of violation of the tightness of the connection, gas leak may appear here

To extend the service life of the connection, it is stained with oil paint. After drying the composition, a dense film is created that can reduce the likelihood of a leak.

Elimination of gas stove malfunctions

Before starting the repair, it is important to know that all gas reinforcement is made of their alloys that do not give sparks in contact. In the process of recovery work, it is worth using similar materials.

Passatigi, a divorce key for the slab and valve, gas key will be necessary from the tools.

Problem #1. burning malfunctions

When the smell of gas appeared as a result of a faded flame. It is necessary to immediately close the valve, ventilate the room. A similar situation is considered an emergency case, so you need to immediately open the windows wide open. When the burner cools down, it is important to thoroughly blow it, clean it from food residues, fat.

During the operation of the stove, a carpet accumulates on the burners, which can give the flame a yellow tint. This can be misleading, creating the appearance of a malfunction where it is not.

Serviceable burner provides a flat flame of blue color. If the tongues of yellow, red skip, this indicates a malfunction of the burner, the probability of fuel leakage

After thoroughly cleaning the burner, it is necessary to install it in place, light, check the performance

If any defect is the cause of the malfunction, it is worth replacing the burner with a new.

Problem #2. breakdown of the connecting hose

The hoses used to connect gas are sold at specialized retail outlets. Visually, they differ from the rest of the bright yellow shell.

Gas supply hose, connecting elements, differ in bright yellow braid. This allows you to highlight the elements suitable for creating a gas pipeline from another similar product

When the cause of the leak was a crack in the hose, it is worth replacing it. After all, the repair will provide a short.term effect and the unpleasant odor will appear very quickly again.

Problem #3. leakage in the area of ​​the locking crane

To check the operation of the node, it is necessary to apply a soap solution to the pipe. If a leak is detected, you need to immediately block the gas supply, call professionals. In the presence of a new valve, linen pack, the master will quickly replace the gas crane.

At the end of the installation, the connection is delayed until the valve rises to the desired position. The correct installation is determined by repeated application of soap solution.

The shut.off crane is located on a pipe connected to the central line. Also, the problem can be in the valve at the site of connecting the stove to the cylinder. In case of violation of the tightness of the connection, gas leak may appear here

To extend the service life of the connection, it is stained with oil paint. After drying the composition, a dense film is created that can reduce the likelihood of a leak.

At the first signs of a malfunction, it is worth contacting professionals. It is worthwhile to engage in troubleshooting on the presence of specialized knowledge, experience with gas equipment.

Common causes of smoking fire

When everything works stably, the flame of the burners, the burners should be blue, evenly distributed through the working area. Reddish or yellow color indicates a lack of oxygen, the presence of additives in the mixture, and incomplete combustion. It is this coloring of fire that leads to smoking.

There are several ordinary breakdowns that become the reasons for the appearance of soot on pots, pans, cauldrons or exhaust with a strong flame:

• Clogging in the nozzle. In this case, the mixture coming from the hole that cuts the flame does not pass completely, its path is blocked by garbage, mud, adhering fat, and soot. Fix it simply. remove the upper cover, and clean the nozzle, sometimes with particularly strong jams, soak in water. Then everything is installed back.
• A hole was deformed. The repair is excluded here, a replacement is required. Deformation occurs for various reasons, often. prolonged operation without maintenance.
• Low fuel quality, too many sulfur elements. With trunk gas supply, such a nuisance is extremely rare. Often smokes a gas cylinder used in the country, in a private country house. It is necessary to change the supplier, replace in urgently.
• High pressure in the container. Fuel simply does not have time to burn, so it smokes a burner. It is required to adjust the pressure, and everything will return to normal.

As you can see, not all moments when the gas stove is smokes from the gas cylinder or the highway, are associated directly with the operation of the equipment. That is why it is better to abandon independent attempts to repair the product, since unprofessional intervention can harm stably functioning equipment.

Why smoke an oven?

When the burners in the oven are smoked, the causes can be similar, as well as radically different from smoking of the burner. Usually, the following stands out by specialists:

• The pressure in the cylinder or the highway is much higher than what is required in accordance with the technical conditions of use.
• The presence of extraneous impurities in the cylinder, which make the composition of poor.quality. Manufacturers or suppliers add many sulfur additives to the composition, which is why the fire starts to dirty dishes, pots.
• The settings of the oven are not adjusted. Modern models of manufacturers such as Gefest, Hansa and others require very subtle adjustment, which depends on many parameters, starting with the features of gas supply to the personal requirements of the user. With rare exceptions, the consumer will not be able to figure out the intricacies of the settings, so you should call a specialist from “repairing”, which will not only configure in the right way, but also give a detailed advice on using.
• Flowing nozzles. If the nozzles in the burners can be cleaned yourself, then the arrangement of the oven is much more complicated. Therefore, in this case, they immediately call masters.
• Poor quality of burners. Some budget models are made from poor.quality materials that have a minimum durability. Because of this, the heating elements that have already served their term begin to work unstable. In particular, smoking may appear. Eliminating the problem is simple. a broken product needs to be replaced. over, it is necessary to use a better product than the manufacturer installed.

When it smokes inside the oven, you need to immediately refuse to cook food in it. This negatively affects its quality, and can cause severe food poisoning.

Recommendations of specialists

Service centers have developed a list that will help to avoid the occurrence of problems, as well as protect the house from the occurrence of a fire.

• Do not leave the device unattended in the on state (even if you are in the next room).
• Do not stay at night in a room with gas equipment.
• Do not let children in the technique, and also try to protect pets from it from it.
• Try not to equip the kitchen in a room where there are no windows or there are problems with ventilation.
• Before use, open the oven for several minutes so that gas is released from there.
• Do not use the device for other purposes: do not hang the laundry over it, do not operate as a means of heating the house.

Breakage in which the smell of gas appears at the stove can occur in any apparatus, regardless of its life or manufacturer. Employees of SC “Repair” can eliminate the defect. Our engineers go to the client at the established time, eliminate the flaw in one visit. We also provide a guarantee for all repair work and installed parts.

The main causes of soot

The gas stove works fine if the flame in the burner of natural blue, without impurities of red and/or yellow shade. Когда в пламени появляются разноцветные языки, газ подается неравномерно, то назвать такую ​​работу корректной нельзя. The reddish tint of the flame indicates that the fuel does not completely burn out or not enough air to burn gas.

The presence of red flames often precedes the appearance of soot.

The reason is like an unpleasant phenomenon considered:

Когда газовая смесь содержит слишком много меркаптановой серы, появляется густой, черный дым, частицы которого оседают на посуде, стенах помещения.

Incorrect work of fireplace, the presence of soot in the process of combustion may indicate low gas quality, reduced or increased pressure in the system

A similar situation is noted when connecting a plate to a low.quality cylinder with low mas. In some cases, soot appears in the presence of malfunctions of the burner itself.

Reason #1. Low fuel quality

I figure out why soot appears from a working gas stove, it is important to know that the cylinders are refueling with a gas mixture. When the composition of increased sulfur, soot appears.

If you are absolutely sure that the cause of soot was poor.quality fuel, you can file a complaint with other organizations of this profile.

Together with the statement, you will need to provide:

Often such incidents are decided peacefully in favor of gas consumers. You do not know what needs to be done when a gas stove that works from the cylinder is smokes and what measures can be taken urgently?

• Try to move the cylinder or gas stove to another place;
• If you have friends who use the services of the same organization that refueling cylinders, specify whether the gas stove has a gas stove;
• Contact the fuel supplier with a request to explain the increased sulfur in the gas mixture;
• In the absence of contact with the organization that refueling the cylinders, write a complaint with a request to restore justice and compensate for the value of property spoiled by soot.

Starting the proceedings with the fuel supplier, make sure that the problem is as a gas. We also recommend that you familiarize yourself with the requirements for cylinders when refueling and filling standards.

The actions of unscrupulous suppliers do not pose a danger to the health of the cylinder gas users, but creates a lot of inconvenience during operation

In addition to gas supply problems, the cause of soot is often the need to adjust the equipment and eliminate malfunctions.

Reason #2. incorrect slabs settings

I figure out why the household gas stove connected to the Block of Propan is smoked, it is important to evaluate the level of pressure in the system. It depends not only on the quality of the cylinder, but also on the features of the work of the burner. To deal with the problem, it is important to know the device of the last.

The burner consists of the following elements:

• Clusher. designed for uniform distribution of fuel around the entire perimeter of the burner. In appearance, the cutter resembles a sleeve, which is cut along the contour.
• The cutter cover provides the desired diameter, looks like a rounded cover made of stainless steel, is located on the upper part of the cutter.
• Elektable candle. an element of modern gas plates models. Iskra is a signal for the start of work, gas is lit from it. There is a candle on the side of the cutter, a temperature sensor is located nearby, which ensures the safety of operation of the plate. If the fire has gone out, a command is transmitted to a special electromechanical device,
• The nozzle is located under the cutter, looks like a small bolt with a through axial hole. The nozzle is responsible for uniform fuel supply, regulates pressure.

The appearance of soot, incorrect operation of a gas stove. all this is often associated with the installed nozzle, or rather, with a too large hole in it.

Disrooping the burner, pay attention to the nozzle. The hole in it should not exceed 1 mm, otherwise a soot will form when the gas is combined

Uneven fuel supply may be associated with the presence of blockages. To clean the nozzle, you must carefully insert a thin wire into the hole, twist it between the fingers. Pressing, picking a nozzle is not recommended. This can lead to an increase in holes, the appearance of soot.

In the presence of dirt, do not forget to clean the rest of the details, since soot may appear as a result of combustion of deposits accumulated on the surfaces of the burner. Rub through all the elements with an old toothbrush moistened in a washing tool. Then rinse the parts under running water, dry well. Only after that proceed to assembly of the gas stove.

Reason #3. insufficient air volume

Insufficient amount of air that is supplied to the burner will lead to the appearance of soot even with the goodness of all other elements. To adjust the air disks, it is worth unscrewing the stop screw, act very carefully.

Air discs are adjusted very carefully. At the end of the work, the flame should burn evenly, during the operation of the burner there should not be extraneous sounds

Upon completion of the adjustment of the operation of air discs, you must immediately check the quality of the gas stove.

When the burner is turned on, the gas should burn without extraneous sounds, buzzing. Flame languages ​​should not be more than 2.5 cm in height. If the adjustment has not helped, it is worth returning the air discs to its original position.

When to replace the nozzle?

Modern gas stoves, for the most part, are designed for a centralized gas supply. The central networks use methane, the pressure in the system differs from pressure in the cylinder, so a hole in the nozzle is necessary a slightly larger diameter. When using the cylinder gas, propane is used to ensure domestic needs, so a nozzle with a smaller hole is needed.

In the basic configuration, nozzles are always used to supply fuel through centralized highways. The configuration of modern models may include a spare nozzle designed for balloon gas. Also, for the use of cylinders, the gas reducer will be replaced additionally.

Trying to get rid of the cause of soot on the burner of a household gas stove, it is important to purchase a nozzle corresponding to the brand of household appliance. Otherwise, the replacement of the part will not bring the expected result.

The correct selection of a nozzle, competent installation provides uninterrupted operation of a gas stove. If there are installation errors, the fuel will be supplied unevenly

There is no nozzle in old models of gas plates. However, they are equipped with a mechanism that allows you to regulate the intensity of fuel flow. You need to correctly configure it. Adjustment is carried out by turning the crane, which is equipped with a gas cylinder. Not unscrewing the valve to the end, it is easy to reduce the pressure of the gas in the system, minimize the likelihood of soot.

In certain situations, soot appears when the oven is turned on. It is likely that the nozzle is also needed here. In most gas stoves, the nozzle is located behind the left wall of the oven camera, into which the burner is inserted, curved by an arc. To replace the nozzle, you need to unscrew the screws, remove the burner, find and replace the part.

With prolonged operation of the gas device, the jet could boast of the burner to the snot. In this case, you need to lubricate it with a special composition, wait a few minutes.

When the nozzle is deformed. the fuel comes to the burner unevenly, the appearance of soot is possible, the accumulation of gas in the device, which is a danger. To replace the nozzle, you need to see the brand of the gas stove, choose suitable components.

It is important to remember that gas equipment refers to potentially dangerous, therefore, with any breakdown, it is advisable to invite specialists from the gas company with which you have concluded a service for maintenance.

When to replace the nozzle?

Modern gas stoves, for the most part, are designed for a centralized gas supply. The central networks use methane, the pressure in the system differs from pressure in the cylinder, so a hole in the nozzle is necessary a slightly larger diameter. When using the cylinder gas, propane is used to ensure domestic needs, so a nozzle with a smaller hole is needed.

In the basic configuration, nozzles are always used to supply fuel through centralized highways. The configuration of modern models may include a spare nozzle designed for balloon gas. Also, for the use of cylinders, the gas reducer will be replaced additionally.

Trying to get rid of the cause of soot on the burner of a household gas stove, it is important to purchase a nozzle corresponding to the brand of household appliance. Otherwise, the replacement of the part will not bring the expected result.

The correct selection of a nozzle, competent installation provides uninterrupted operation of a gas stove. If there are installation errors, the fuel will be supplied unevenly

There is no nozzle in old models of gas plates. However, they are equipped with a mechanism that allows you to regulate the intensity of fuel flow. You need to correctly configure it. Adjustment is carried out by turning the crane, which is equipped with a gas cylinder. Not unscrewing the valve to the end, it is easy to reduce the pressure of the gas in the system, minimize the likelihood of soot.

In certain situations, soot appears when the oven is turned on. It is likely that the nozzle is also needed here. In most gas stoves, the nozzle is located behind the left wall of the oven camera, into which the burner is inserted, curved by an arc. To replace the nozzle, you need to unscrew the screws, remove the burner, find and replace the part.

With prolonged operation of the gas device, the jet could boast of the burner to the snot. In this case, you need to lubricate it with a special composition, wait a few minutes.

When the nozzle is deformed. the fuel comes to the burner unevenly, the appearance of soot is possible, the accumulation of gas in the device, which is a danger. To replace the nozzle, you need to see the brand of the gas stove, choose suitable components.

It is important to remember that gas equipment refers to potentially dangerous, therefore, with any breakdown, it is advisable to invite specialists from the gas company with which you have concluded a service for maintenance.

When a gas stove smokes, it is necessary to start diagnostics by checking the conformity of the nozzle type of fuel. If everything is in order here, you should pay attention to the quality of the fuel. It is recommended to refuel cylinders only in trusted organizations. In some cases, the appearance of soot is associated with the presence of a malfunction. To find a breakdown, correctly eliminate it, it is worth inviting a professional.

Ventilated VS. Gas magazines without ventilation

When burning firewood or other combustible materials in the fireplace, smoke gases and smoke are directed up through the chimney passing inside the chimney. This process is known as ventilation. For gas fireplaces, homeowners have the opportunity to use ventilated gas logs and ventilated combustion gases, or they can use gas logs without ventilation, which do not produce smoke and gases detected in ventilated gas logs. In the case of gas logs without ventilation holes, the fireplace often emits the smell of kerosene when the ventilation holes are closed.

Since gas logs without ventilation burn without ventilation provided by ventilated gas logs, the combustion process works a little differently in terms of how heat is released. In the case of ventilated gas logs, the chimney thrust works as part of the process of burning or burning. The traction also works to pull the smoke and gases up and in the outer air. When using gas logs without ventilation, carbon and hydrogen materials contained in natural gas are recombinated with oxygen and hydrogen with the formation of carbon dioxide and water vapor. In fact, the final product looks like warm. Когда природный газ не сгорает полностью, камин будет выделять керосиновые запахи в качестве побочного продукта.

Mixtures of natural gas

In its pure form, natural gas does not have a smell in the form of gas or when burning. However, natural gas distributors add additives or impurities to gas sources for various reasons. One of these additives has the smell of a rotten egg, which is designed to prevent users about gas leaks. Methylmercaptan acts as another additive used with natural gas. When burning, methylmercaptan has a smell similar to burned matches and rotten eggs. When logs burn in the fireplace without ventilation, the additives to natural gas are burned together with gas. As a result of this combination, fireplaces will emit the smell of kerosene when burned in an environment without ventilation holes.

Although the presence of kerosene smells may not indicate the problem with the fireplace, the burning of logs in a closed ventilation fireplace can lead to other undesirable effects. Incorrect or incomplete combustion processes can lead to accumulation of soot on wood. Soot arises as a result of partially burned emissions of natural gas.When this happens, part of the carbon used during combustion turns into soot, while other carbon molecules are connected to oxygen, forming dangerous carbon monoxide gases. Even in cases where soot does not accumulate, burning firewood without ventilation for a long time will lead to depletion of oxygen reserves in the room, so after a while some ventilation form is needed.