Electrolux washing machine flashes the start button green

Electrolux washing machine codes. Zanussi. AEG

Error control circuit 1 level of anti.bias 1. Input voltage is always 0 in.

Error control circuit 1 level of anti.bias 2. Input voltage is always 0 V or 5V.

Error of the control circuit of level 1 press start. Input voltage is always 0 V or 5V

The pipe of the press startup is clogged. The air dodger system is closed

Malfunctioning the relay of the heating element

Door locking malfunction

Deviations of the instrument system of the door locking device

The malfunction of the sensor sensor of the door of the door

Short circuit of the engine triac short circuit in the engine circuit

No signal from the tachogenerator blocked the engine is faulty electrical wiring

The error of the control circuit of the engine flip. Input voltage is always os or 5v

No signal from the tachogenerator. The signal does not come within 15 minutes

Inverter current exceeds the threshold value (15a)

Engine current passes its threshold value (4.5a)

There is no signal from the tachogenerator for 3 seconds after a new rotation speed is set, from zero

The temperature of the cooling radiator exceeds the threshold value (88 ° C)

The voltage in the DC circuit drops below the threshold value (430V)

FCV cannot accept and/or send a message within 2 seconds

Communication error between FCV controls and the main printed circuit board

The board constantly requests configuration parameters due to repeated testimonies

Insufficient heating during the washing program

Overheating when performing a washing program

Malfunction of the relay of the heating element or relay of the drying system

Earth current leak in the circuit of the heating element of washing or drying system

A malfunction of the heating element during washing (the heat.subject is open)

Malfunction in the relay circuit of the heating element

The malfunction of the nutrition relay of the heating element (the discrepancy between the condition of the sensor and the relay K1)

NTC NTC sensor

NTC sensor failure at the outlet in drying mode

NTC sensor malfunction at the entrance in drying mode

NTC sensor in washing mode, incorrect position

Malfunction of the sensor sensor of the recirculation pump

CIMISTOR COMISTOR Code

Incorrect setting of the control panel

Microcontroller malfunction of the control panel

Communication error between the control panel and the main board

Incompatible communication protocol between the control panel and the main board

Incorrect configuration of the washing program cycles

Communication error between the microprocessor and EEPROM memory

Discrepancy between the version of the hardware and the configuration of programs

The discrepancy between the selector and the setting of the program cycles

The communication protocol between FCV and the main board does not match

Inconsistency between the sound block and the e.electronics

Incorrect setting of the control panel

Malfunction of the touch control panel

During the engine is turned on, there is no data from the drum positioning sensor

Demonial malfunction of the drum positioning system: open door open

The power frequency goes beyond the permissible limits

Too high power voltage

Too low power voltage

WD Pati relay heating element, sensor malfunction signal

The discrepancy between the sensor of the protective relay state of the FCV relay

Electromagnetic valves are blocked

Communication error between the joint fee and WSD board

Communication error between the joint fee and WD

The inconsistency between the sensor of the relay of the heating element 1 of the WD board and the state of the relay of the heating element 1

Fault relay sensor of the heating element 1 WD board

The discrepancy between the sensor of the relay of the heating element 2 of the WD board and the state of the relay of the heating element 1

Failure of the relay of the sensor of the heating element 2 WD board

Incorrect signal or lack of a signal from a tachometer

The discrepancy between the condition of the engine fan and the signal of the sensor of the control circuit

Cliff in the WDM heating element chain

Faulty microcontroller of the main board

The frequency of the power source goes beyond the permissible limits

In case of malfunction.

Filters are clogged in the water supply line, water supply failure, worker, an integer temperature, and labor generation

detergent), and the washing machine performs foam removal,

stage with re.launch with better distribution of linen in the drum.

The lid does not open at the end of the cycle:

too high temperature in the tank, the lid is released after 12 minutes after the completion of the program.

The drum did not reach the right position from-

In the event of a malfunction malfunction, button.

The drain filter is clogged, clogged or overheled the drain hose, the drain is too high

The “Start/Pause” button closes the water supply valve, blinks a red water supply in the water supply network.color:

Air conditioning for fabric is media

Depending on the model.In some modules, the sound signal may turn on. After eliminating the possible causes of the malfunction, press the Start/Pause button to re.start the interrupted program.

Safety Information

Keep the launch of the washing program for 2, 4 or 6 hours, by pressing the “Start Delay” button.

At any time, before pressing the Start/Pause button, you can cancel or change

I launch delays by pressing the “delay” button again (when all indicators are

gasped, the washing program will immediately begin).

If you need to change or cancel

I end the cycle after the “Start/Pause” button was pushed. Act

To cancel the postponement and start

the delay, you should turn the sovereign

During the delay in the start time of the cycle

Cover, put the car into a pause mode by pushing the “Start/Pause” button. After

The cover will be closed again, press the “Start/Pause” button.Time Managernazhi several times the “Time Manager” button

also choose the level, depending on

go, how contaminated the linen. By default

Everyday washing: easily contaminated

Suffers indicator: for washing is weakly

linen fast washing: slightly polluted

The possibility of applying these modes for

different levels of pollution depend

from the type of selected program.Starting Processable Machine button “Start/Pause”. To follow

Drive the cycle. the corresponding in-

During the execution of the cycle, the selector remains

motionless. this is normal. Glowing in-

Dikator corresponding to the current cycle.

Preliminary washing washing: Rinse outbreak

Interruption of the program to add linen during the first 10 minute the “Start/pause” button:

The indicator will blink green

while the car is in the state

pauses. After the car stops,

the cover can only be opened after 2

minutes. To continue the implementation of

grams, click the “Start/Pow.za” button again.

Before making changes to the execution

the program of the program, you should transfer the car to

on, “Start/pause” button for a few seconds

blinks red if you still want to

Men programs, you should cancel the current

If you want to cancel the program, turn

NITEL program selector in the Stop position “

The completion of the programmash will stop automatically, the indicator of the “Start/pause” button will go out, and the in. the end of the end of the cycle

Table with information codes (error codes)

In the table below, we listed the ELECTROLUX washing errors codes, a brief description of possible problems and the reasons for their occurrence.

Poor pressure of water or its absence, blockage in the system of water bay, breakdown of the input valve, the sevenistor of the control module

The tightness of the hoses, connections or tank is impaired

E20, E21, EF0, EF1, E23, E24

Blockage in the drain or sewage system, breakdown of the drain pump or control module

E31, E32, E33, E34, E35, E38

E40, E41, E42, E43, E44, E45

The hit of foreign objects into the lumen of the hatch and the lock mechanism, the deformation of the cuff, the breakdown of the door blocking system and the lock mechanism, the control of the control board

The motor of the motor burned out as a result of a short circuit

E50, E51, E53, E54, E55

Violations in the work of the motor itself, its winding, the simistor or chain connecting the motor and the simistor

E52, E56, E59

Violations in the work of the tachogenerator, its contacts

E61, E62, E66, E68, E69, E3A, E71, E74

The machine cannot heat water or heats it too much

Incorrect operation of the temperature sensor or heating

The washing machine does not respond to commands from the dashboard

Violation of the connection between the control module and the washing machine panel

Incorrect drum loading, the car is uneven

Using too much powder or poor quality powder

The frequency of the supply voltage does not correspond to the permissible limits

Problems with a power grid or control module

In the video posted below, you can once again familiarize yourself with the methods of eliminating the faults of the Electrolux washing machines, indicated by different information codes.

About the author:

Mom, wife and just happy woman. Draws inspiration in travels, does not represent life without books and good films. Seeks to become an ideal mistress and is always ready to share the experience gained.

Found a mistake? Select it and press the buttons:

For washing small things on the road or hotel, it is convenient to use a regular plastic bag. Socks or tights are kneaded inside the tied package with water and a small amount of detergent. This method allows you to pre.soak things and perform washing without damaging the fabric and without spending a lot of powder and water.

The expression “soap opera” (“soap”) did not accidentally arise. The very first series and show, whose audience made up women, were broadcast on television at a time when housewives performed cleaning, ironing and washing. In addition, to attract spectators to screens on the air, advertising rollers of detergents were often scrollful: soap and powders.

Washing machines are related to the emergence of “wash money”. In the 30s of the XX century, American gangsters used the laundry network as covering their illegal activity. Giving income from criminal activity for revenue received from cleaning clothes, they turned “dirty” money into “clean” money.

The first officially patented washing machine was made of wood and was a box with a frame filled to half with wooden balls. Inside, the laundry for washing, the detergent and with the help of the lever moved the frame, which, in turn, forced the balls and wipe the linen.

History is known when the kitten fell into the drum of the washing machine and, having passed the full washing cycle on the Woolen things program, got out of the unit whole and unharmed. The only nuisance for the pet was an allergy to washing powder.

Cosmonauts, being in the orbit of the Earth, solve the problem of dirty things with the original method. Clothes are dropped from a spaceship, and it burns in the upper layers of the atmosphere.

There are a variety of balls that are used in the washing machine. Antistatic will not give the fabric to stick to the body after washing, balls with special loops will “comb” the villi and prevent the appearance of the rollers, and silicone with pimples will not allow fluff when washing outerwear washed.

There is a washing machine “For bachelors”. Linen washed in such an unit does not need to be ironed at all! The thing is that the device does not have a drum: some of the things can be placed inside the container directly on the hangers (for example, jackets and shirts), and smaller things (for example, linen and socks). on special shelves.

In the XIX century, a lot of time was leaving for the washing of ladies’ toilets. The dresses were pre.opened, and then washed and dried each part separately so that the fabric would not deform. After washing, the clothes were sewn again.

How to clean the steam generator from scale

Instructions for installing a ceiling drying-liana

DIY underwear dryer

What is the difference between a steam generator from a steamer: what is better to choose

How to choose a drying machine for home underwear: tips, parameters

Do.it.yourself renovator repair

How to choose a floor dryer for linen: tips, best models, video

How to clean the scapard of scale at home

How to use a converter for clothes, instructions

OE error on LG washing machine

How to clean the washing machine with vinegar and other means

Electrolux washing machine codes

Stirkaved.ru © 2022. When using materials from the site, the active reference is obligatory.

TOP-10 of typical breakdowns of Electrolux smell and ways to solve them

There are a lot of factors that can affect the working capacity of the washing machine, but some are very rare, while others are many times more often. To solve basic problems, it is enough to study 10 typical breakdowns and ways to eliminate them.

Does not start

Когда одежда загружена в барабан, порошок в своем отсеке, и остается лишь выбрать режим и запустить технику может возникнуть проблема: стиралка не включается. The difficulty is that the information board also does not work, so a visual inspection will have to be conducted for diagnosis:

The network filter is located under the wall, burnt traces or bloating of the case can speak about its malfunction.

Water is not gained and does not merge

The work of washing machines is equipped so that during one washing, water changes several times. To find that the malfunction in the fence of the liquid can be immediately after turning on, there will be no noise processing, and washing will not begin.

Cleaning the tract will help to solve the problem:

• It is necessary to block the shut.off valve, turn off the hose from the washer;
• Pull the filter net, plots are used for this;
• The filter and hose are cleaned of pollution.

It is also advisable to check the valve with a multimeter. If this part is out of order, then it will have to be replaced with a new. If the technique takes water, but does not drain it, then you need to clean the drain. It is located under the loading hatch.

The powder does not pick up

After several years of operation, the quality of washing is noticeably falling. There are spots on the clothes, and it is not at all the wear of the technique.

It happens that the problem is that part of the powder remains in a special compartment, and only clean water is used during washing.

Features of the structure of the SMA are that the liquid enters the compartment, it is mixed with household chemicals and transported to the working area. Water falls into the powder compartment through a special valve, which can clog.

To diagnose the problem, it is enough to check whether the powder is left after washing in the compartment. If it is, then the following actions are performed:

• A ditch is removed from the machine.
• The inlet valve is checked.
• If the part is clogged, then it needs to be cleaned, if worn out, change.

Rinse does not work

Check whether the rinse really does not work on the special mode. If the problem is really this and the mode does not work, you will have to repair the control fee.

Only people with electronics skills will be able to independently repair the control fee independently. If there is no such experience, then it is better to contact the masters.

No pressing, the drum does not rotate

Notice that the drum does not rotate after the launch of the washer can visually. The cause of such a malfunction may be problems with the drive belt. Depending on the degree of wear, there are two options for solving the problem:

• When the belt flew off, but it is still in normal condition, you just need to pull it back. First, one side is pulled onto the motor pulley, and then the other side on the pulley pulley.
• If the rubber is stretched or cracked, you have to replace it.

Another reason may be in the brushes of the motor, because they are responsible for the transfer of current to the rotor. During operation, the rods of the brushes gradually wear out. If the degree of wear is more than 50%, then you need to replace them with new.

The drum stopped in the wrong position

It also happens that when the washing is completed, a person opens the upper cover and sees a drum in front of him, the doors of which are in the open position below.

The reason for such a phenomenon may be a breakdown of a locking part or loose closing the wings. The problem usually is one.time and rarely appears.

In order not to call the master and not spend a lot of money on it, it is better to turn the drum on your own.

• We need a long steel wire, at the end of which a hook is made;
• The wire drops down down, you need to try to put the sash and close the tank;
• The drum is scrolled into a normal position.

Water does not heat up

The fact that washing is carried out in cold water becomes noticeable immediately. Additional factors are the appearance of an unpleasant aroma and a deterioration in the quality of washing. The problem can be in the heating element, sensor or board.

To begin with, Ten is checked:

• You need to remove the rear panel of the washing machine.
• There is a heater in the lower part, all wires are disconnected from it.
• Temperial measurement sensor must be removed from the case.
• The nut, which is located in the center, must be slightly twisted and pressed on the bolt.

The operating capacity of the heating unit may be prevented by the scale, it must be removed. If the heater does not work after cleaning, you will have to buy and install a new. If the reason is in the thermal attewer, then you will also need a new part.

The technique starts, but the machine operates

If an emergency shutdown of power supply has occurred after the launch, then you need to call the master. You should not try to run the machine again, it is dangerous.

Often the reason for the operation of the RCD is:

Noise during operation

During washing, the technique vibrates and “jumps” throughout the floor? There are three possible reasons:

• Incorrect installation. To reduce the minimum of vibration and rattling, the equipment must be put on an even and hard floor.
• Dysbalance. If all the clothes are lost on one edge of the drum, it will touch the wall with this side. To prevent this, you need to evenly distribute the laundry.
• Bearing breakdown. It will require a complete disassembly of the washing machine to replace it.

A third.party subject got into the washing room

An accidentally left thing in trousers or jacket can pass through a cuff or hole and be outside the tank, because of this:

Instructions for disassembling the household appliance

The disassembly process begins with preparation, it is important:

• Prepare tools in advance. You will need screwdrivers, pliers, claw keys. Additionally, you should stock up on the WD-40 spray or analogue.
• Prepare a place. Washing is a overall technique, and in order to disassemble it needs enough free space.
• Remove the plug of cars from the outlet.
• Drain all the remnants of the liquid, pull the linen out of the drum.

The next step will be the dismantling of the external components of the design of the washing. It is necessary to remove the lid, walls, compartment for detergents, for this:

• On the back you need to find and unscrew two screws, dismantle the panel.
• The dull for household chemicals must be removed to the stop and press on the “tongue”, it is located in the compartment for the rinseum.
• Unscrew the fasteners that under a box for powder, additionally unscrewed the screws of the hatch.
• The hatch’s clamp should be slightly placed with a screwdriver and carefully tighten.
• The screws are located to the left of the electronic panel, they need to be dismantled, and then put the mounts to remove the electronic module.
• After the module is pulled out, access to self.tapping screws holding the back and front panel will appear.

The final stage of disassembly will be the removal of the tank-backing unit. It is better to do this with an assistant, because it is quite difficult to extract the drum yourself.

• First you need to turn off the terminals from the power unit, then scroll through the pulley with one hand and pull the belt with the other;
• It is necessary to unscrew the screws that fix the engine;
• after unscrewing, the motor needs to be slightly shifted and pulled out;
• Then the pump wires are turned off, the screws are unscrewed. to shift the pump, it must be turned clockwise;
• removing the wiring and sensor and heating, then the nut located in the center is unscrewed, the heating unit is pulled out with swinging movements;
• The screws are unscrewed, the nodes are dismantled;
• After that, it remains to remove the dispenser nozzles, the wiring of the bulk valve and the press.

What to do after?

As soon as washing is over, it is necessary:

• unload the washed underwear from the washing machine drum;
• Wipe the rubber cuff from moisture with a clean cloth (additionally check the sealant for stuck small clothing items);
• open the dispenser for detergents (if insoluble powder remains in the tray, it is necessarily removed);
• Open the hatch door for ventilation (ventilation of the inner surface of the drum prevents the formation of an unpleasant smell of shake).

You should not immediately after the sound of the end of the washing try to open the hatch door. For another 2-3 minutes, UBB holds the door closed. Sudden movements, twitching can break the lock.

How to care for technology?

Electrolux will help to extend the uninterrupted operation of the Electrolux washing machine.

So the drum and the powder compartment at least once a week are wiped with a soft sponge using a paste of baking soda (dry powder is diluted with warm water until thick gruel is standing). Such actions help clean the surfaces of lime plaque and other impurities of hard tap water.

Do not forget about the rubber cuff around the hatch. It is in its folds that the largest amount of dirt is collected, which a soft toothbrush and baking soda paste will help to clean.

The rubber seal cannot be cleaned with chlorine.containing compositions (for example, with white). Otherwise, the cuffs will lose its elasticity very quickly, will be covered with cracks.

Particular attention is required by the drain filter and the filter of the water bay. To avoid problems with the drain of a spent liquid, with a frequency of ten days, it is necessary to clean the drain filter. You can find it in the lower part of the case behind a small hatch.

The drain filter is twisted (counterclockwise movements), cleaned of hair, threads and other garbage, and then mounted in the same place.

Covered with a layer of particles of impurities of tap water, the filter of the water gulf blocks the process of setting water into the washing machine. How to clean it? To do this, on the rear panel of the body of the washing machine, the mounting nut of the pouring hose is unscrewed, from which a small metal mesh is neatly with a flat screwdriver. a pouring filter. The grid is cleaned under the pressure of water with a toothbrush, and then installed in the same place.

Once a week, the body of the washing machine is wiped with a soft rag or sponge moistened with soapy solution.

Bosch

After pressing the “Start” in Bosch washingships, the hatch is blocked and the key icon lights up. At the end of the cycle, the machine is automatically unlocked and, having turned off the car from the electric network, after one to two minutes, the hatch can be freely opened.

If the Bosch washing machine is accidentally turned off before the end of the program (or for example, an emergency shutdown of electricity has occurred), then the car will remember and then turn on from the same place.

Often it is necessary to open a locked door before turning off the machine. To do this, turn the handle of choice of programs to the one that was executed the last. Then the key should light up with constant light, as it should be when the machine is working. And then the lock is then removed in the usual way. by pressing and holding the “Start Start” button for five seconds.

Ariston

When blinking the key in Ariston machines, you need to check:

• Is the blocking option from children included. Maybe someone accidentally pressed the buttons or the function was forgotten to turn off;
• The work of the control module. Should turn off the machine from the network and turn on after 10 minutes again.

Sometimes there are situations when with a flashing key indicator, there is no other indication on the ariston display. Most likely, there is a breakdown and you should check the machine according to the possible faults indicated in the instructions.

ELECTROLUX Washing Error Code with display

If the Electrolux washing machine control panel is equipped with a special scoreboard (a liquid crystal panel), then the device fits a signal about the malfunction in the form of an information code (letter and numbers). It is enough to decipher the alphanumeric code to determine the exact cause of the breakdown of the household appliance.

E10, E11

A signal of problems with a set of water into the drum (during the washing process there was a failure, the drum did not have time to get into the time allotted by the program or there is no water in the tap).

• Check the pressure of water in the tap,
• inspect the bulk hose for excesses and mechanical damage,
• Test (if necessary to replace) a water level sensor in the tank.

A signal of attempts to gain water in the tank during drying. Reason: The input valve of the water fence is faulty. What to do: replace the faulty element.

Signal about water leaks in the pallet. Cause:

What to do: very carefully examine all the nodes and elements of the washing machine for mechanical damage, if necessary, replace damaged elements (most often the problem is solved by replacing the drain pump).

E20, E21, EF0 EF1

Water drainage signal. Cause:

• Check for blockages and, if necessary, clean the water pipe.
• The impeller of the drain pump.
• Test and, if necessary, replace the drain pump.

Clean the sewer (a very slow or completely absent flow from a sink or bathroom signals a traffic jam in a pipe). Read more about the error here, why there is no drain of water. here.

E23, E24

Signal about the malfunction of the symistor of the control of the drain pomp. Problem: the systemist of the electronic board burned out, the integrity of the connection of the contacts between the pump and the simistor is violated.

What to do: test the control module with subsequent repair of faulty elements or installing new.

Signal about the malfunction of the press. The control unit without obtaining reliable data on the filling of the tank with water, stops the launched washing process.

Reason: the water level sensor in the tank failed. What to do: test and, if necessary, replace the water level sensor in the tank.

Signal about incorrect work of the press. Reason: violations in the flooding system of washing machine, breakdown of the water level control sensor in the drum.

A signal of problems with the sensor of water control sensor in the drum and a protective ten relay. Cause:

What to do: check for the clogs of the press starting tube, test the contacts of the heater and the water level sensor.

Signal about the excess of the permissible water rate in the tank. Reason: Pressure breakdown. What to do: diagnose and, if necessary, replace a faulty sensor of water level control in the tank.

E40, E41, E42, E43, E44, E45

Signals about problems associated with locking the hatch door. Cause:

• Loose door is easy to closed,
• Deformation of the rubber cuff,
• Luke’s locking device failed,
• Damage to the lock mechanism.

What to do: check for the presence of extraneous objects a rubber cuff, the openings of the door lock (if necessary, remove the blockage). If nothing that would interfere with the closure of the door is detected, it is necessary to test the UBB multimeter (Luke lock device).

Additionally, the lock is checked for mechanical damage (for example, the curved tongue interferes to closely close the hatch door). All damaged, failed elements are subject to replacement. Read more here.

E50, E51, E53, E54, E55

The signal of the engine malfunction, the motor windings, the breakdowns of the simistor and the chain connecting the motor and the simistor. With such malfunctions, there is no rotation of the drum. The washing machine blocks the hatch, but the washing process does not begin.

Cause:

• Flapsed the motor, tachogenerator.
• The symistor is faulty on the electronic controller board.
• The connection between the engine and the Simistor is violated.
• Engine winding.
• Test the simistor and other elements on the board in the motor circuit (most often such repairs are trusted to professionals),
• Replace the motor brushes,
• test and, if necessary, replace the engine speed sensor.

In a situation of damage to contacts in the motor circuit (most often occurs due to water entering the engine), a complete replacement of a faulty element is required.

E52, E56, E59

The signal about the malfunction of the sensor controller rotation of the engine (tachogenerator). Reason: the tachogenerator failed. What to do: test the element with a multimeter, if necessary, replace a faulty sensor.

E57, E58

Signal about increased voltage in the power supply network. Reason: Problems in the wiring. What to do:

• Check the correct connection of the washing machine (the connection is excluded through the extension cord).
• Voltage parameters in the network.
• Serviceability of the outlet (with ground) in which the household device is included.

E61, E62, E66, E68, E69, E3A, E71, E74

Signals about problems associated with heating water in the drum (water temperature does not correspond to the parameters given by the program at the right time).

• The heating element came out of standing,
• Relay Ten,
• The problem with the wiring of the heating element,
• The temperature sensor is faulty.
• Test and, if necessary, replace the termistor, heating.
• Inspect the contacts of the heating element.
• Check the correct location of the termistor.

Electrolux washing machines for faults without a display

Electrolux washing machine without a display on the control panel is a blink of indicators. Depending on the type of control module (EWM 1000 or EWM 2000), the combination of code blinks and the method of decryption differs.

In the washing machine with the EWM 1000 control module (you can clarify the type of module in the household appliance passport), you can decipher the error code by flashing two LED bulbs located near the Start/Pause button and the end of washing (in the photo P.2).

The number of flashes of the first LED is the first digit of the error code. By the number of flashes of the second indicator, the second number of code is determined.

For example: the first indicator blinked three times, after two seconds the second indicator blinked five times. Such a combination of indicators blinks signals an E35 error.

In a washing machine with the EWM 2000 control module, eight LED bulbs are involved in the decoding of the breakdown signal (located vertically on the right side of the panel). The four upper lights are responsible for the first digit of the error code, four lower LEDs. and the second number of code (in the photo p.3, p.four). The countdown of LED bulbs begins to up.

Using the table, we will consider with an example of decoding the Error Error code E53. In the lower row of four indicators, the first and third light bulb lights up, in the upper row of four indicators the first and second light bulb lights up.

Repair all types of Electrolux washing machines

On the Electrolux EWS 125210 A washing machine, after turning on the fork in the socket, the LEDs do not light up, after a while the “Start” button, the program selector, stands in the “Off” position. What to do?

First you need to check the voltage in the outlet. The machine does not pass self.diagnosis, and you need to check the lock (UBB), the heater, the command.apparatus and the electronic module.

Why is the Electrolux washing machine flashing?

Any, even the most modern technique can fail. Electrolux washing machines. no exception. Therefore, most of them have a function of self.diagnosis, which allows you to determine the nature of the malfunction without calling the master. There are quite a lot of reasons for the refusal. Some of them require the intervention of qualified specialists, while some can be eliminated independently. The form of a breakdown of the Electrolux washing machine signals error codes that begin to flash on the indicators panel. For them we can conclude which alternative to dwell on: contact the service service or try to eliminate the problem on your own.

In what cases are indicators flas?

The lamps on the indicators panel can flash both one and several. In any case, this indicates the occurrence of any malfunction that violates the normal operation of the washing machine. Indicators light up in the following standard situations:

• Lack or low water level in the drum.
• The drum does not rotate.
• Water does not merge after the washing program is completed.
• Spontaneous water drain.
• Lack of water heating.
• Slap or breakdown of the control module.

For most breakdowns, including the above, alphabetic-digging malfunctions are displayed on the display. They are represented by the letter “E” with the subsequent number. In the absence of a display, the code is deciphered according to the number of flashing indicators on the front panel.

There are a lot of codes of washing machines. As a rule, they are given in operating instructions for each model of Electrolux washing machine. The most common breakdowns are considered below.

Electrolux washing machine flashes what to do?

The first thing to do is to pay attention to the door of the hatch. With its loose closure, the washing machine will not start.

Next, check the voltage in the outlet. If it is absent, the cause of the protective device (RCD) may be the cause. It needs to be brought to the working position and turn on the washer again. If this did not help, then the matter is not in the car, but in the electric circuit. Here we need an electrician, not a master in washing machines.

The next object of the examination will be the power cord. If there are traces of damage, it should be replaced.

If the listed manipulations did not give a result, then the case acquires a serious character. It is possible that the cause of the malfunction is the failure of the electronic control board. In this case, it is unlikely that it will be possible to do without the services of a service center.

The washing machine does not flood or does not drain water

The water supply to the machine is provided by pressure in the water supply network. If he is too weak, the washing will have to be postponed. It happens that the input valve refuses. Replacing it is easy. A mesh filter is installed in front of the valve. He must be clean.

A more common problem is the lack of drain. Here you have to check the entire drain system, starting from the drain hose and ending with the drain pump. The simplest thing that can and should be done is to check the drain hose and filter: there should be no bends on the hose, and mud on the filter. If the problem is not this, it is better to call the master to check the pump and control module.

Spontaneous water drain

Elementary reason. incorrect connection of the drain hose to the sewer. You need to adhere to the connection scheme given in the manual. serious reasons are a failure in the operation of the control module or sticking of the flood valve. This will require the help of the master.

Water does not heat up

If, 15-20 minutes after the start, the water heating does not occur, the probable reason is the breakdown of the heating element or the thermostat. The performance of both is checked using a multimeter. The replacement of any of these elements can be made independently. they are available on sale. The main thing is that their parameters correspond to the models of your washing machine.

The drum does not rotate

If the weight of the linen is not exceeded, and the drum refuses to rotate, then the essence of the problem lies either in the drive belt, or in the electric motor, or in the control module. Changing the belt is easy. As for the motor, the number of errors reaches eight (here the wear of the brushes, the refusal of the revolution sensor, and the opening of the chain, etc.D.). So the problems associated with the operation of the engine and the module are better to entrust professionals.

If the maximum load is exceeded, the drum may begin rotation, but after filling with water, stop. And in the presence of an imbalance sensor there is a drum will refuse to rotate if the laundry is laid out unevenly (lost in lumps).

Washing powder from the tray is not washed off

Most often, the problem with the wash of the detergent occurs for two reasons: the blockage in the subositor tray or the wear of the input valve supplies to the tray. In the first case, it is enough to make a thorough flushing of the tray, in the second. replace the valve. Both of them are not much difficult.

Slap or breakdown of the control module

As can be seen from the foregoing, this node is involved in many problems. The failure is usually eliminated by re-turning on the machine after a pause of 15-20 minutes. If this does not work, the module must be replaced with the involvement of a specialist of the appropriate qualification.