Home Article Cleaning Philips Azur Performer Plus
Article

Cleaning Philips Azur Performer Plus

How to clean the iron from the scale Philips Azur?

Keeping an iron above the sink, hold the cleaning button from scale and shake the iron with neat moves back and forth until all the water flows out of the tank. The scale will be extracted, and steam and boiling water will come out of the sole of the iron.

Turn on the Calc Clean function using a button or regulator (the method depends on the model: if necessary, press and hold the button). Gently shake the iron forward and backward until all the water comes out. Water, steam and scale will leave the holes for the steam.

Self.cleaning

How to clean the Philips iron from scale inside in the absence of self.cleaning function?

Lemon acid

It is impossible to use the device immediately, you need to give time to dry, because when processing the iron with this method, water can get to the elements that are energized during operation.

Remember that an unpleasant odor will be released during operation, so processing must be carried out in a well.ventilated room, or if there is an extract above the stove.

Lemon acid

It is impossible to use the device immediately, you need to give time to dry, because when processing the iron with this method, water can get to the elements that are energized during operation.

Remember that an unpleasant odor will be released during operation, so processing must be carried out in a well.ventilated room, or if there is an extract above the stove.

Special remedies for removing salt deposits

Industry produces a variety of irrigation products. The instructions for use are the same for everyone or differs from one another insignificantly:

  • Pour the composition for removing the scale into the container
  • include in the network at the maximum temperature
  • After disconnecting, press the self.cleaning button or, in its absence, the steam release button above the pre.prepared container (pelvis, large pan)
  • Repeat 3-4 times adding liquid to the container
  • Rinse the device with clean water until the remains of the solution are completely removed

General recommendations for all types of purification of Philips ironing:

  • When preparing a solution to remove scrap, you need to strictly observe the proportions so as not to harm rubber and silicone gaskets
  • use cleaned or boiled water. In the case of pouring the finished scrap solution, check whether it should be diluted and in what proportion
  • For safety reasons, carry out procedures only when the iron is disconnected from the network
  • After completion of work, rinse the container 2-3 times with clean water

To prevent the formation of salt deposits inside the water capacity, as well as in the exhaust channels for the steam, the following recommendations must be followed:

  • Pour only boiled or mixture of tap and distilled water into a vessel in a ratio of 1: 3
  • in breaks put the device in a vertical position
  • after the end of ironing, drain the remaining liquid
  • purchase a special water treatment filter for ironing, which can be purchased separately

In modern ironing devices there is a built.in filter, whose operating time is designed for the entire operation of the device.

Manufacturers do not recommend using only distilled water, steam forms worse. The effect of an overheated steam arises, which negatively affects the process of smoothing.

Modern Philips iron is designed to iron. A wide variety of models allows you to choose an option for use for their needs. The presence of a steamer makes it possible to smooth the folds on the linen without much effort.

Folk methods

For long.term and reliable work, several options for eliminating scale are used. Failure to comply with these actions can lead to a deterioration in heat transfer or failure of the device.

Vinegar

In order for the cleaning procedure to go successfully:

  • Take water, vinegar (proportion 1: 1);
  • Pour into the internal container by 1/3;
  • heat the electric device to high temperature;
  • withstand 10 minutes;
  • The Philips iron will turn on, turn off, not prevent the process;
  • Horizontally hold it above the bowl, clamping the “steam” button;
  • The procedure is performed until the liquid in the tank ends;
  • Fill it with purified water, turn it on, heated hard, releasing steams, the residues of the scale will come out with it;
  • Drain the remaining water, wipe the base with a clean cloth.

In order not to inhale a vinegar pair of vinegar, you need to work with an open window.

Sparkling water

Water (200 ml) pour into the internal container, heated the iron. Select the “steam” function, press the button. The whole exfolved scale will come out. Repeat the process several times until clean water goes.

Trinosa carboxylic acid

Using citric acid, you can qualitatively clean the philips iron from scale inside at home.

  • 20. 25 g of citric acid dissolve in a glass of water at room temperature;
  • pour the product into a well.heated iron;
  • withstand 10 minutes;
  • Keep over the sink, let the steam press the button until rust comes out of the holes of the sole;
  • drain the remains from the iron and fill it with purified water;
  • Steam release continue;
  • Wipe the base of the device with a clean rag.

How to clean the iron at home

At home, remove the scale from the outer surface and internal elements of the iron with the help of:

How to use chemical cleaners

The most common are German means, which include organic acid, water and anti.corrosion substances (Topperr, Bosch, Filtero 605).

  • We prepare a solution of water and agents in a ratio of 3: 1.
  • We heat the iron at the maximum temperature.
  • Turn off.
  • Put the device horizontally and leave for 2 hours.
  • Pour the product, and wash the iron 1-2 times with water.
  • Before ironing, we check by ejecting the steam purity of the iron.

Special liquids from scale cope perfectly with its removal from the surface of the iron

The most affordable cleaning method is citric acid

  • 2 h. l. pour citic acid into half a glass of hot water.
  • Drink soft tissue in this solution.
  • Attach it to the holes on the iron.
  • After a few minutes, remove the fabric and turn on the device, and clean the holes later with ordinary cotton sticks.

To clean with citric acid, the iron inside, make a solution of 25 g of powder and 200 ml of water.

  • Pour the solution into a water container and turn on the iron on the maximum temperature.
  • Wait for re.turning on, and when the device turns off for the second time, release steam. Heated solution in the form of steam will fall into the channels and soften the scale.

Rusting rust vinegar

This method perfectly removes the rust from the sole of the iron, but has several disadvantages:

Heated sole slightly iron the fabric moistened in a solution. It is important to take care of ventilation of the room.

How to remove an air cooker?

Dilute in a liter of water 2-3 bags of citric acid and turn on the humidifier to work with this solution. In a few hours, check the result. If the scale remains. repeat the cleaning, if the raid is removed. thoroughly rinse the capacity of the moisturizer with clean water.

  • For an effective solution, 30 grams of acid in a liter of warm water should be dissolved.
  • Fill the tank with the resulting liquid.
  • Leave the solution in the tank for twenty minutes.
  • Turn on the steam generator for maximum power.
  • Start ironing, preferably old and unnecessary things.

How to use the function of self.cleaning iron?

Connect the iron to the outlet and set the maximum temperature. After full heating (the light indicator will turn off), turn it out of the outlet and place it above the sink or bathroom sole. Click and hold the corresponding button, than drive the self.cleaning system into effect.

Literally, the translation of Self Clean on the iron means: self.cleaning.

This automatic system is designed to help us fight with the advent of a hated lime plaque and rust in the ironing irons with a steam generator easily and effortlessly. During operation on the internal surfaces, microparticles of lime and rust appear.

The process of eliminating the raid is not complicated. The main thing is to do the procedure on time and regularly. Use clean water, not hard to avoid problems. After each ironing, wipe the sole with a napkin moistened in water.

Утюг PHILIPS Azur Performer Plus GC4520/30 | Распаковка. Обзор

Many Philips irons have a built-in steam system or a separate butor station. The steaming function reduces ironing time, so the devices are indispensable assistants in the house. However, even such modern equipment is subject to pollution during operation.

Self.cleaning

Cleaning products with pair function (gravity type of steam generators) carry out at least 1 time in 1-2 months. The procedure is also necessary if a special indicator is provided in the iron, which flashes about a significant pollution of the electrical appliance.

  • Prepare a bowl or pelvis to collect liquid;
  • put the regulator in the “without pair” position and set the maximum temperature;
  • Fill in the tank of the iron with water;
  • Turn on the device to the network when the heating indicator goes out. turn it off;
  • Place the iron over the pelvis, shake it several times and press the steam giving button;
  • When water ends in the tank, turn on the steady device into the network and reward several times a piece of fabric, cleaning the sole.

Many modern Philips ironing models operate on steam stations (pump.out type of steam generators), which are also equipped with built.in automatic cleaning.

Note! The manufacturer recommends automatically cleaning at least 1 time in 14 days.

Easy Rinsing

If you have a question how to clean the Philips steam generator, then the procedure is designed to regularly remove the formed scale in the iron steam generator:

  • The electric device should be disconnected from the network if the iron worked before cleaning. let it cool within 2 hours;
  • Remove the device from the steam station;
  • Remove the tank (if it is removable) or take the base with both hands, shake it thoroughly several times;
  • remove the special Calc Clean valve or unscrew the steam generator lid;
  • Carefully tilt the container above the sink or bathroom, drain the entire liquid;
  • Pour again a small amount of purified water (about half the total volume necessary to fill the tank) and repeat the entire procedure 2-3 times.

After easy cleaning, put the lid or valve in the same place and you can start ironing.

Smart Calc Clean

This system is a mode designed to eliminate the resulting layer of scale. During the cleaning, the device should be in the included state:

  • Pour into the steam generator purified water (to about half the tank);
  • If on the regulator of heating your electrical appliance model there is a “CALC CLEAN” position, install it;
  • Put a special container on a flat surface (ironing board, a table with a spread towel), install an iron on it;

Be careful: during the procedure, the special container heats up greatly, so wait 5-10 minutes before picking it up.

The need for such cleaning will be indicated by the sound signal made by the steam generator and flashing the light indicator on the body or handle of the iron.

IMPORTANT! It is unacceptable to leave the electrical appliance unattended during cleaning, interrupt the process or move the iron. If pure water comes from the sole during the procedure. there is no scale in the inside of the striking device.

Pure Steam scale cartridge

It is a shift filter filled with granular substance, which eliminates rigidity salts, transforming the positive charges of calcium and magnesium ions into negative. This element is suitable for irons with a steam generator Perfect Care Pure.

The cartridge removes most of the organic compounds and salts from the liquid, so that for ironing, you can use water from the tap.

The need to replace the element is reported by the indicator flashing and the sound signal of the household device. The service life of the steam generator part depends on the intensity of using the iron and, as a rule, is from 1 to 3 months, after which the old cartridge is thrown out and put a new. Useful information: cleaning the steam generator from scale

IMPORTANT! If you do not have spare elements left, and you need to urgently stroke things. use an iron with the previous filter, but pour the water into the tank demineralized, otherwise the iron will not turn on.

What means and tools should be used and why

The choice of means and methods of cleaning depends on the degree of contamination of technology from the inside and on the surface.

In case of not very “advanced” cases, the function of self.cleaning of modern Philips models can cope with the problem.

Self.cleaning

The steam supply button is located in most philips ironing devices in front

Find out whether the model is equipped with a Calc Clean system, you can in the instructions for operating the device. If the answer is positive, then you need to do the following:

  • Turn on the device with the vault. heat to the highest temperature. wait for the shutdown.
  • Wait again the stages of turning on and disconnecting.
  • After repeated disconnect, remove the device from the network and press the cleaning button.
  • The scale will be eliminated under the action of a pair of high temperature and is removed through the holes. Gently shake the iron to accelerate the process. Cleaning must be carried out over specially designated dishes for this, which does not happen over the ironing board with things and not over the sink. Polluted water can ruin them.
  • Wait for cooling and rinse parts with clean water or special means.

On separate modifications of Philips, there is a built-in De-Calc indicator that informs users about the need to clean the device. There is also a big plus of the latest generation devices. a built.in container for collecting a nabi in the Quick Calc Release system.

note! The choice of a means to cleanse the outer part of the iron should be taken careful. Do not clean with acids and abrasive substances ceramics, Teflon and aluminum surface. To cleanse the sole, pencils, ammonia, hot baths, hydrogen peroxide, toothpaste, acetone are standard.

Safe chemistry to combat a scope

This volume is enough up to about 10 applications to prevent iron pollution

The domestic sections of stores are forced by a variety of finished chemical powders and solutions for cleansing. Experts recommend making a choice in favor of these funds, t.to. Their action is tested and safe for technology. “Chemistry”, which helps to cope with the problem in a short time, how to clean the PHILIPS iron from scale, as follows:

  • “Antinakipin”. sold in the form of a finished liquid or powder for breeding in water. If this is a finished solution, just pour it into the tank, turn on the iron, leave for 30 minutes. Turn off the iron, pour the solution, rinse 2-3 times tank. If this is a powder, do exactly the same actions, having previously divided it in water in the proportions prescribed in the instructions.
  • Topperr. use only breeding in water according to the instructions, t.to. The product is quite concentrated. Heat the iron to the maximum, pour the solution and leave for 2 hours. Pour the solution already with a sediment in the form of a descended scale, rinse. Fill the tank with water again, heat and steam. Thus, holes on the surface of the iron will be cleaned, which are also clogged with lime.

Means with similar principles of action are: Top House, Optima Plus PO-020, Delu, Luxus.

note! The Cillit tool is different in the way. The iron needs to be heated to a high degree and into the holes of the sole with a pipette, or in any other way, pour in a drop of substance. Leave for a quarter of an hour, then steam the iron with clean water, wipe the sole itself with a rag. To avoid burns, do this only after cooling the surface.

The possibilities of steam ironing of the linear series Philips

Both the PHILIPS GC 3320 ironing irons, and some other devices of a number of models can be charming using the Calc Clean function. Unlike the Quick Calc Release function, recommended by the manufacturer every 2-3 weeks, Calc Clean is enough to spend time for a month, or immediately after changes on the indicator (the Philips GC 4411 steam iron is equipped with this function).

If you are interested in an article on the topic. Philips Torkt Kare Azur How to Clear, read our next article.

After connecting the function, the “without pair” mode and the largest temperature are selected. Pour water into the tank (to the largest mark), turn on the iron and wait until the pointer is turned off. All this time is kept on a container or shell for collecting the rubber and dirt. The final stage. the iron shakes, helping in this way a removal of hot water or a couple with a scale. After the end of the procedure, clean the sole of the iron.

Likewise, the Philips Azur iron how to clean from scale can be without additional means, only due to the function of self.cleaning.

Folk methods of salvation from scale

When for some reason it is not possible to use the self-cleaning function (it does not work, or it is usually not provided), it is advisable to try folk methods in the work.

One of them is proven citric acid. Powder (1-2 bags) is mixed with distilled water, poured into the device’s tank and a steam mode is turned on. Available and safe replacement. min. water. It is also poured into a reservoir requiring cleaning, including steam mode.

A good way to cleanse not only water capacity, but also pair holes. lemon juice diluted with water in a ratio of 2: 1. A cotton wool is moistened in a lemon solution, the holes are treated with its help. Fresh water is poured into the tank for final cleaning and steam mode is turned on.

Philips azur performer plus

Tips

Several tips of experienced housewives will help to solve the problem of scale as quickly as possible:

  • If you pour softened water (ordinary tap water boiled for ten minutes with a small amount of baking soda), then you will have to clean the iron less often.
  • The cleanliness of the anti.license rod must be checked at least once every one and a half months.
  • You can avoid the rapid appearance of the plaque if you pour distilled water into the iron (sold at any gas station).
  • After cleaning acetone, the device is tested on unnecessary clothing. This will help to avoid the appearance of yellow traces during ironing.

The more often the cleaning will be carried out, the longer the life of the household appliance will be.

Learn more about the ways to remove the scale from household appliances. here.

Lemon acid

Let’s move on to the study of the presented devices.

Morphy Richards 303131

The iron effectively smoothes the fabric of any kind. The sole is resistant to mechanical damage and loads, as it is made of durable and high.quality camelines. For safety in everyday use, automatic shutdown of the device with prolonged inaction is responsible.

For long.term work without a break, there is a water tank with a significant volume. The iron is connected to a standard electric network with a voltage of 220 V. The model retains operational properties for many years. The sole with three special zones effectively eliminates the folds on clothes.

A ferry blow 200 g
The length of the cord 3m
Anti.capel system Yes
The sole of the iron Cross
The volume of the tank 400 ml
The weight one.7 kg

.

Easy to use an iron with good reviews and many additional functions. The price for the model is now very affordable, I saw last year it cost a thousand more expensive. I personally am very pleased that the iron is quite light, but with a very powerful steam blow and a function of vertical steaming. In general, it has everything that I needed, I am very pleased with the purchase.

Philips GC4555/80 Azur

The power of the iron is 2,400 watts. Thanks to this, it quickly heats up and provides an excellent result of ironing, including when working with things hanging on the shoulders. It is convenient to hold the rubberized handle in the palm of your hand, confidently controlling each movement.

The base of Steamglide Plus is made of durable material, which is difficult to scratch. It slides well through various fabrics. This model provides a Quick Calc Release system. It allows you to remove the lime coating with minimal time and, accordingly, increase performance and extend the service life of the device.

A ferry blow 190
Anti.capel system Yes
The length of the cord 2 m
The volume of the tank 300 ml
The weight one.6 kg
The sole of the iron ceramics

Price category: from 3 850 to 4 700.

It suits everything! Good iron iron. Ironing quality, power, weight, ease of use. This model left only good emotions! Very much like Philips devices. The previous comrade worked for 8 years and still alive. But they decided to replace the old man buy a new Philips Gc4555 iron. Just a plane, not a device. Gorgeous color scheme. Sound in the soul so that it is not possible to imagine that some iron is better than this model.

Morphy Richards 305003

The iron is made in the blue case and is a powerful and convenient device with which you will love the ironing process. Its power corresponds to 2400 watts, and the power of steam blow reaches 230 g/min, which will allow you to smooth the folds on several layers of clothing.

Continuous supply of steam occurs at a pressure of 1.5 bar at a speed of 50 g/min due to the built.in pump. This allows a couple to penetrate deeper into the fabric, providing effective smoothing of folds. Ceramics sole supports Aeroglide technology that distributes steam evenly over the entire surface, which helps to create a steam cushion.

The peculiarity of the model lies in the design, which involves the presence of a display and control buttons on the front side of the case. Using buttons, you can turn on the steam continuous supply mode, use a steam blow, and also turn on the backlight in the nose zone to see small folds. To connect the device, a 3 m long cord is used.

A ferry blow 230 g
Anti.capel system Yes
The length of the network cord 3m
The sole of the iron ceramics
The volume of the tank 350 ml
The weight one.69 kg

.

I decided to buy an iron in return for the old. I purchased this model. In general, I am satisfied. Like the device. It works well, heats up quickly. The sole does not stick, since the temperature is adjusted automatically and it is impossible to burn things. Even thin fabrics are strictly stroked, you are not afraid that you will burn the material and the thing will have to be thrown away. I advise you to purchase this device. He really costs his money, high.quality and reliable.

Author

Goltilar

| Denial of responsibility | Contacts |RSS