Candaline washing machine does not turn off water supply

The washing machine does not get water into the drum and buzzes: what to do, frequent reasons

Using modern household appliances such as a vacuum cleaner and machine machine, we facilitate the task of cleaning and washing. When the device fails, ceases to fulfill its functions becomes inconvenient and difficult to live.

Therefore, if the washing machine does not gain water.

Naturally, everyone wants to cope with a malfunction on their own, especially since some details are easy to replace. But it is worth noting that if the washing machine does not gain water, the reasons can be the most unexpected and their repair will not always cost cheaply.

The most common reasons why the washing machine does not get water

When the washing machine LG, Bosch, Samsung, Siemens start to fail, you will understand it immediately.

As a rule, if the machine, the machine, starts quickly and the washing time itself corresponds to the installed, including filling, washing, rinsing, draining and squeezing.

If you erase often, then you know that each mode of drain, washing and seas a certain time. Therefore, if this time began to increase for unknown reasons, then most likely the problem lies in the ability of your washing machine to be filled with water.

Of course, problems can be different, possibly requiring serious intervention of professionals. There are also reasons that can be found independently. Let’s see how to recognize poorly incoming water and what the causes of this malfunction lies in.

Lack of water in the system

The most banal and simple reason why the washing machine does not pump water is the lack of liquid in the water supply. Naturally, if you have disconnected water, then the water supply hose will be empty.

As you know, the machine does not erase without water, the program will neither begin any action, and also until the water fills the camshaft container for powder and will not be set in the drum itself.

Do not explain that the pressure of water in the water supply plays the most important role in the operation of the washing machine.

Therefore, if the water is supplied in your apartment weakly or completely turned off (the pipes broke through the neighbors, the housing office turned off for prevention, etc.D.), then do not worry that the problem lies in the typewriter. Therefore, before eliminating problems, check the presence of water in the tap.

The water supply tap or weak pressure in the water supply was blocked

Another common problem, on which there is no water supply in the washing machine is a crane overlap.

As in the previous case, if there is no flow of water into the car, then it is useless to wait for the washing that washing suddenly for no reason begins.

Of course, this option is little likely, but still do not discount it from the accounts. As a rule, the water supply valve could be turned accidentally when you cleaned the house or specially overlapped water, leaving on a long trip. So, before identifying more serious causes of malfunctions, minor trifles should be excluded.

The filter clogged

Everyone knows why the pipes of the water supply or in special containers are installed filters. Sometimes slightly, and sometimes sufficiently contaminated water clogs the filter of a mesh located on the back of the car along with the hose through which water enters.

If the problems listed above were not found, then check the filter, if you hear a characteristic buzz and at the same time the water is slowly gained.

Surely, if the machine does not gain water at all, then the matter is in this iron mesh that must be pulled out and cleaned. This is done using water and needles. If after the actions done still water does not enter the washing machine, then the breakdown is associated with more serious reasons.

The reasons for the breakdown

Automatic washing machine works according to a simple algorithm. Pressing the Start button blocks the door loading door and launches the washing process.

If water does not enter the washing machine at the beginning of work, the program fails, it will be impossible to complete the washing.

Diagnose washing and find the source of the problem. Some malfunctions are eliminated without the help of plumbing at home.

There are 8 of the most common reasons why the washing machine does not gain water:

• Water supply problems.
• Cut the flood hose.
• Filter pollution.
• Incorrect work of Luke lock.
• Water supply valve malfunction.
• Damage to the details.
• Failure of board.
• Damage breakdown

Residents of apartment buildings take such a measure of precautions when leaving for the weekend or on vacation. They overlap water so as not to flood the neighbors from below, and upon the return they forget to open.

Water supply problems

Water enters the machine through the hose connected to the water pipe.

Water is not typed in the washing room in the case when the supply is suspended by communal services. If there is no water in the house, it, respectively, cannot be in the typewriter.

When the water begins to be supplied through the pipeline, the problem will disappear.

Important: turn off the washing machine until the water appears in the system. Otherwise, the washing is facing a breakdown.

Reducing the pressure level in the water supply system is another reason why the washing machine does not gain water, or the set process is very slow.

Open the water tap and check the pressure. If the water is dripping or poured with a stream, call the housing office to clarify the situation. How to give pressure. resume the wash.

Cut the flood hose

It is difficult to pump water for the pump if the pipe connected to the water supply is clogged, bent or transferred.

Inspect the pouring hose. If the fastenings are reliable and sealed, there are no leaks, there are no heavy objects on the hose. look for blockage.

The standard size of the internal diameter of the filling pipe is 14-16 mm. Hoses from 1 to 5 meters long are released from solid reinforced material. Grind the objects that come inside outside it will not succeed. We’ll have to disassemble.

Filter pollution

Water water is not sterile and contains impurities of small particles. The presence of garbage can disable even the most expensive and functional model of washing machine.

To protect the washing machine from the hit of the water impurities of sand and rust, there is a built.in cleansing filter on the filling hose.

Over time, the mesh is clogged with extraneous contents, which makes it difficult to supply water to the tank of washing machine.

To clean the filter, remove the fence hose.

Incorrect work of Luke lock

The machine is arranged in such a way that the subsequent action of the step.by.step program will not start without the completion of the previous. The water supply to the drum does not begin if the hatch cover does not fit tightly. The machine does not gain water due to the failure of the Luke lock program.

Neping the clicking mechanism arises for three reasons:

• pollution of the latch or groove;
• damage to the rubber gasket or plastic locking mechanism;
• Washing failure.

Pollution on the latch appears from the door of the washing powder, stain.coir, rinseum. A layer of plaque accumulates and dries. Lock lock does not work.

The malfunctions of the mechanism arise due to wear during prolonged operation. Replacing worn out elements requires a sociable service center or private master.

The signal of the indicator of a malfunction on the electronic screen indicates an error in the work of software or blocking contacts. In this case, do not repair yourself, so as not to make it worse.

Tip: if the car is under warranty, contact the service center. Location coordinates and contacts are indicated on the last pages of the instructions for the washing machine.

Water supply valve malfunction

The flood hose of water set is equipped not only by the filter. The pressure of the incoming fluid regulates the water supply valve. The inlet mechanism works as an automatic shut.off valve controlled by an electric coil. When water is supplied, the shutter opens, and upon receipt of the signal about filling the tank to the desired mark, it closes automatically.

Failure failure prevents water from pouring into the washer.

To check the valve, you need to remove the fence hose, filter and top cover of the washing machine.

Damage to the details

The most common problem associated with the process of water gain is a breakdown of the press. Round plastic sensor is responsible for the water level in the tank. The wires connected by a train, and a pressure tube are brought to it. A faulty part can be mistakenly signaling the command apparatus about the completeness of an empty drum.

To verify the performance of the sensor, remove the top cover of the washer, disconnect the wires and the pressure pipe.

Failure of board

The machine may not fill the water due to a breakdown of the electronic control board, which is located under the top cover.

The electronic system can give a failure of the program in conditions of high humidity in the room where the machine is worth.

Damaged power supply or plug cause damage to the board. Unstable voltage in the network can provoke a short circuit. The capacitors on the board can burn due to voltage drops.

In this situation, you need to solder the tracks on the board and install new capacitors. In this case, it is better to invite a specialist.

Damage breakdown

The programmer is a rotary lever or a round handle on the front panel. The mechanism provides the switching of the washing modes.

Under the plastic case are a gearbox and a motor, gear and contacts. Wear of one or more elements will lead to a malfunction of the programmer. The difficulty of repairing the part depends on the type of control lever.

Two types are installed on washing machines: mechanical and electronic.

The simplest model is the mechanical programmer. This lever rarely breaks, most often the reason is in wear. The service life of a mechanical programmer is about 10 years.

Repair of faults

It is sometimes possible to solve the problem with a set of water in a washing machine yourself. Depending on the cause of the breakdowns, use the tips to eliminate them.

A method for cleaning the pouring (fence) hose, filter, water supply valve and pressostat:

• Disconnect the laundry washing;
• Cross the tap on the pouring hose of water supply;
• Unscrew the hose, look at the lumen, rinse under the pressure of water;
• Remove the mesh filter with pliers and rinse;
• Unscrew the bolts from the back and dismantle the top cover;
• Split the fasteners with pliers, disconnect the hoses and remove the valve;
• attach the valve to the hose and let the water: the working mechanism will delay the liquid, the faulty will show the leak;
• Closely attach the multimeter terminals to each valve contact: if the resistance is less than 2 kilos, the part is not working and must be replaced;
• Check the water level sensor for external damage to the body;
• Clean the metal contacts of the press stratum with a cotton swab moistened in alcohol;
• Remove the pressure tube and rinse with water;
• Put the hose back, open the tap of the pouring hose and run the wash by a new.

In the case when the machine does not want to fill in the water, and the software display issues error information, the device needs to be taken to the warranty point of service or other specialized service center.

Other malfunctions

Several more common faults of the washing machines can be distinguished.

Water is not gained

This situation may arise in the absent (blocked pipe) or insufficient pressure in the system. One of the possible reasons is the blockage of a mechanical filter of a pouring hose. In this case, it needs to be unscrewed and cleaned with a brush at the entrance.

Another probable reason is broken in the inlet valve. If this part is faulty, the car will not type water. Valve replacement instructions:

• unscrew the flood hose;
• Remove the top cover;
• Remove all the wires and hoses leading to the valve:
• Separate the part from the case of the car, unfastening the latches or unscrewing the bolts;
• turn the valve and pull it out;
• Replacing the part with a similar one, install it in a place.

Replacement of the intake valve is a simple procedure, so the repair can be done with your own hands.

The bearing broke

This malfunction is accompanied by a characteristic loud knock during the operation of the machine. The process of replacing the bearing is a rather laborious matter, it requires certain skills and dexterity.

• turn off the power of the machine and unscrew the hoses;
• Remove the top cover and unscrew the counterweight;
• remove the belt from the pulley of the drum;
• Disconnect the wires leading to the heater and the engine;
• take out the motor;
• Disconnect the hatch, having previously twisted the screws under the cuff and picing the fixing the clamp with a screwdriver;
• The tank is disassembled into two parts, the pulley is removed from the rampart of the drum;
• Old bearings are knocked out by light tapping and new.

If you can change the bearing at the car with a detachable tank if there are components, then the unreliable tank will make the task almost impossible at home. The only thing that can be done in such a situation is to contact the service center.

Cuff replacement

Elimination of the problem occurs according to the following scheme:

• open the hatch;
• squeeze the clamp with a screwdriver, which goes along the entire circumference of the hatch;
• stretch the front of the cuff;
• remove the inner spring clamp, removing the top cover;
• change the cuff to the new one;
• fix the clamps in the reverse order.

The part can be worn out over time, it can also damage it in sharp details.

Candy Aquamatic and Holidy errors

Candy Aquamatic washing machines with a display are convenient in that in the case of a breakdown, an error code that signals a particular malfunction occurs on the screen in the case of a breakdown.

Error codes in candy machines with a display:

• E1. Problems with Luke lock (the door did not slam to the end).
• E2. Water intake error (it does not act or poured in excess).
• E3. Water merges either very slowly, or does not merge at all.
• E4. The filling valve works incorrectly (the water level in the tank is higher than the necessary).
• E5. There is no water heating. A malfunction can lie in a malfunction of the heater, electronic controller or thermal attewer.
• E7. Problems in the tachogenerator. The device that controls the engine speed is faulty. The motor works incorrectly, for example, quickly rotates when washing and slowly when spinning.
• E9. Engine shaft does not rotate.

You can recognize a breakdown even in a car without a display. Indicators that flash several times every 5 seconds will help to determine the malfunction.

• Door lock problem.
• There is no gulf of water.
• Water does not merge.
• The built.in protection against leaks worked, the water level above the permissible.
• Temperature sensor does not work.
• Problems with the control module, device memory failure.
• Depending on the type of control module, it may indicate both the breakdown of the motor and the lock of the hatch in a closed state.
• The tachogenerator failed.
• The sevenistor burned down on the control board, which is responsible for processing pulses from the tachogenerator.

12,13. The data transfer process between the control module and the indication unit is violated.

• In the MDL system. failed the control module.
• There was a failure of the program.
• Flake out.
• The tachogenerator works incorrectly.
• The network parameters do not comply with the standards, the control module failed.

A continuous glow of indicators indicates a program failure or breakdown of an electronic control module.

The codes of faults are universal for washing machines. However, depending on the model, some differences may be observed. To make sure of a particular malfunction, you should cheer up with the instructions for a specific washing machine.

The clogged filter

If the noise is heard when the pump is operating, and the drum is full, and the washing machine does not push the linen, then the owner needs to check the drain filter. If it clogs, then it will not work to pump out the liquid.

You will need to clean the filter according to the instructions:

• de.energize the device;
• remove the panel that closes the filter element;
• extract the hose that is used for emergency drain of liquid;
• wait until the drain of water ends;
• Rinse the net.

In the process of removing the filter element from the pipe, water particles should come out, so it is important to put a rag in advance. If this is not, then the net protecting the sewer clogged. For cleaning, you need to contact the master in the service center, first install the filter for the previous position so that there is no distortion.

Diagnosis of an electronic module

To disassemble the housing and look into the inside of the device to evaluate the control board yourself is not recommended. These actions exacerbate the breakdown and increase the cost of repair. It is recommended to call the master.

The specialist will proceed to the diagnosis of the electronic module if he makes sure that there is no other cause of the malfunction or will understand that the problem is determined by the error code on the screen of the washing machine.

The consequences of untimely elimination of the breakdown

If constant self.sample and ignoring this problem is detected, serious consequences may occur:

• Error knocking out an error on the scoreboard;
• stop in the washing process;
• increase in costs for water and electricity;
• increasing the load on the nodes and the premature end of the work;
• Slotting an apartment.

To make sure of a malfunction, you can independently diagnose.

The washing machine picks up water, but does not erase: independent diagnosis

When a water set and problems with the rotation of the drum is detected, independent repair is not recommended. The user can only diagnose.

Emergency drain of water

• Eliminate the fasteners on the back of the case and disconnect the pipe from the sewer drain;
• Lower the hose into the bucket where the water will merge;
• Put the container under the hatch and unscrew the plug.

Tank and drum inspection

The device is turned off from the network, after which:

• Side panels are removed;
• The drum is checked. it needs to be a little scroll;
• Garbage or extraneous objects between the tank and the drum is removed.

If there is no blockage, but the drum does not spin. contact the master.

The jammed bearings

The part is only replaced. Without skills and equipment, independent repair is contraindicated.

Filters cleaning

The machine needs to be turned off. Further actions:

• Removal of the facial hatch under which the filter is located;
• Flushing the clogged element with running water.

Checking the drive belt

The part should stand still. If it is not on the pulley, put with a calculation of 1 clove for 1 pulley. The torn belt replaces the master.

Removing blockages from the pipe

• Unscrew the fasteners on the plum;
• Remove and inspect the hose, feel it with your fingers;
• Gently remove garbage with long wire or knitting needle.

After cleaning the hose is installed again.

Diagnosis of Ten A and Engine

• Check the heater by the tester. the current must pass through it;
• Inspect the engine. If the part is curved, you need to change the brushes.

The reasons why the washing machine has a set of water, but there is no start. many. Some are easy to eliminate independently, others require contacting the master. To prevent a breakdown, load the recommended amount of linen, check your s for small items. When leaps of voltage, it is worth putting a stabilizer. Filters should be cleaned once every six months.

February 20, 2019, 09:29 Feb 1, 2019 16:30 About offenses Link to the current article

Why is the washing machine gaining water and immediately drains it?

If the water set is detected immediately after installation, then the connection of the machine to the sewage system is incorrectly performed. Other reasons include:

• Damage to the electronic control module.
• Electronic control unit.
• Leak the tank of washing.
• The input valve is faulty.
• Problem with a water level sensor, press start.
• Blockage in the drain or sewage system.

Malfunction of the intake (flood, input) valve

The inlet valve supplies water to the tank. The failed part does not overlap the water, the tank is filled completely, the machine immediately drains without washing. If the valve has a weak membrane, then the water will seep even in a closed state. Under the car you can see a leak.

Hopes that the problem will disappear by itself unpromisingly. You need to immediately call the master at home. Often an experienced specialist changes the valve.

Failure of the press.start. water level sensor

Pressostat. the most important element of the washing machine, determines the amount of water in the tank, supplies the command to the filling valve for water supply. The fullness of the tank is determined by the pressure of the water column. The sensor’s bulk tube is clogged due to fine garbage, scale and stops working correctly, giving obviously false information about how much liquid in the drum. Blockage is more often created in the sensor hoses and shutters. With a breakdown of the water level sensor, the part gives incorrect data and therefore constantly pours water. Independently checking the performance of the part is not so easy. Professional assistance is required in the diagnosis, repair or replacement of the spare part.

Our service center has formed its own warehouse of necessary spare parts. Therefore, we are always ready to make urgent repair of your home assistant. The work uses only proven original spare parts from official manufacturers. That is why we give a guarantee for the work of the master and components.

Tank of the Washing Machine

Noticed that the tank of the washing machine passes water? We will deal with the problem. First of all, a crack in the tank is possible. This happens if users forget to devastate s and metal details before washing: coins, tokens, they could get into a small space between the drum and the tank of the machine. Service masters recommend an immediate tank replacement. Although many are limited to the use of moisture.resistant glue, the machine passes the water again.

Another reason for leakage: the laying between the two halves of the tank of the washing machine dry out and gave a leak. It is required to replace the element, it is better to call the master, since the machine will have to be completely disassembled. If a whole tank cannot happen in a machine.

Incorrect connection of the washing machine

When the drain hose is correctly connected, it is above the tank: it is attached to the siphon or directly to the sewer pipe, to a height of 60 cm from the floor. Recently connected a machine, and it constantly picks up water? Check how height is the drain.

It happens that it is not possible to consider the connection place due to the wall, screen. Then you can spend a simple test. When draining water during rinsing, press the pause. If the water continues to decrease, then the matter is in installing a machine. Do not postpone the call of a technical specialist for later. The machine may fail.

Damage of the control unit (electronic module)

The reason why the washing machine does not hold water is a malfunction of the electronic control unit., which is responsible for the operation of many components of the machine, including press strata, pump, heating element and other elements. If the firmware has “flown”, then the simultaneous launch of the bay and drain functions are possible. The electronic board helps to recognize the breakdown where the error code is displayed. A malfunction of the electronic module is one of the most common breakdowns of washing machines of brands Candy, LG, Ardo. This is the most significant detail of the machine, it is worth approaching the repair responsibly and calling a professional master. After all, the cost of the new control unit is quite high, and the specialist can restore the native control unit.

The most frequent reasons for the constant set of water with a washing machine

If the machine has gained water and does not erase or periodically begins to pick up water again during washing, this is possible:

• The electromagnetic valve of this washing machine was out of order and is in the open position. This malfunction can be caused by the ingress of extraneous small objects from the water supply in the form of sand or rust, and maybe due to its overheating caused by poor water pressure in the water supply. This part has an electromagnet winding and heats up greatly with a debt of turning on, therefore, in the latest devices, the tank filling time is limited electronically. In these models, when not reaching the desired volume of water in the tank for the time allotted by the program, the command process turns off the technique and converts it into emergency mode. At the same time, it drains all the water and gives the code of a certain error on the display;
• Damage to the press start. A water level sensor can fail due to the membrane that has lost hermeticization inside it, oxidation and loss of wiring contacts, damage or blocking the hose going from the tank to it. The hose is rubbed most often due to its incorrect laying in the places aligned by the plant;
• Electronic module malfunction. Electronics can get out of stand due to voltage jumps in the supply network, and maybe due to the use of the device in rooms with high humidity. With a breakdown, an electronic module can be mistakenly and uncontrollably given signals for turning on the products of the product, not excluding the filling valve for the washing machine. It is recommended to turn off the electrical appliances from the outlet after washing;
• Incorrect connection of the washing machine that provokes a spontaneous drain of water from the machine. In this case, it is interesting to observe the machine in anticipation when the water level reaches the usual lower part of the hatch glass. But the sound of the incoming water into the tray is heard, but the level is not visible. In this case, there is a large overrun of the water.

Inlet valve

If the cause of the breakdown in this situation is the electric valve of the washing machine, then it is necessary to repair it or replace it. Almost any water valve of the washing machine has a non.collapsible design and its repair can only be made due to its blockage or oxidation of contacts.

In the case of contacts disappears, you just need to clean them, and in the case of extraneous particles, you need to remove them with compressed air or water pressure.

Other malfunctions do not involve the repair of the inlet valve of the washing machine, but only its replacement.

Various manufacturers can arrange their washbasins with different valves. You need to know what you have a water supply valve for a washing machine. They can have one section or two, rarely three. But when acquiring, it is important and taken into account the angle of exit direction, the number of sections and the method of installation on the housing of the household appliance.

To replace the electromagnetic valve of the washing machine, you need:

• Turn off the product from electricity and water supply;
• Remove the top cover of the device and visually determine its location. The Samsung washing machine valve is located on the back of the washing machine case on the left behind the powder bunker. In models with loading on top, its location can be determined by the exit of it from the case to connect the hose, and to dismantle it, remove the panel from the desired side of the case;
• Disconnect the wires and hose from it, then remove it from the mounts;
• It is recommended to set the new inlet valve, observing the reverse procedure, before connecting the tap hose, it is recommended to first open the valve and remove the sand particles and other extraneous impurities from the hose to avoid blocking the protective net of the valve;
• Open a water tap and check for leaks in the hose connections.

You can avoid blocking the valve by installing an additional filter element in the water supply system, as well as observations of proper pressure in it. The tank should be filled on average no more than 2 minutes, otherwise valve overheating is possible.

Which is not recommended to do it yourself

Everyone who has minimal skills in handling modern equipment will cope with a small repair of a washing machine. But if it comes to failures in electronic filling or software, repairs should be entrusted to a professional.

Almost every person is able to understand the simple reasons for the malfunction of the washing machine and eliminate them. An attempt to correct a serious breakdown independently entails unpleasant consequences for both the apparatus and for the owner himself.

Flake out

The heating element of the machine (Ten) sooner or later may fail or just oxidize. As a result. the water that is poured into the tank will bask longer than usual or will not heat up at all. The start of washing will constantly be postponed.

The solution to the problem is obvious. it is necessary to disassemble the cm, get to the heater, check its performance, if necessary, either cleaned from pollution, or replace with a new.

By the way, you can diagnose a problem with the heater without revealing the technique. As a rule, in modern models, in case of malfunctions, an error code is displayed on the display. For each brand of the washing machine there is a list of errors codes. For example, for LG, the heating fault corresponds to the error “he”. In more detail on this topic, see the section on our website: “Error codes”.

Problems with filter and drain hose

If the washing machine stopped in the middle of the washing and does not want to drain the water anymore. this indicates a problem with the water drainage system. First of all, we are talking about a filter and a drain hose. If the hose or filter is clogged, the car cannot release water from the drum in time and continue the wash.

Of course, over time, the water will still leave the drum, but the problem will be repeated, and its solution should not be postponed.

What should be done. The very first thing that is necessary is to clean the drain filter that is located below the machine. Experts recommend cleaning at least once a month. Well, or depending on the intensity of washing. And how many times have you cleaned the filter of your machine? I think the majority will say. yes never! Not doing.

We advise you to certainly study the article: “How to clean the filter of a washing machine”. We also recommend watching a video instruction on the cleaning of the filter:

The drain hose is clogged much less often (in view of its diameter), but if the problem is in it, it is better to entrust the solution to this problem to the specialist. Therefore, how any wrong action can lead to flooding of neighbors from below.

By the way, sediment and rust can clog not only the drain part, but also the pressure tube through which water enters the tank. The fact is that in most models such a tube has a small diameter, so it is subject to elementary clogging. This can also cause a long work to see.