Home Washing machines Bosch dishwasher blinks a brush and drying
Washing machines

Bosch dishwasher blinks a brush and drying

Bosch dishwasher blinks a brush

Do not immediately panic and rush to call the masters of the service center.

  • If the indicator burns brightly, and the dishwasher at the same time functions normally, the water beam has begun.
  • If the work of the technique has stopped, characteristic sound signals in the form of a squeak are heard, the indicator burns brightly or flashes. it is necessary to intervent a specialist.

“Khranik” is located next to the water supply button. The operation of the light signal means that problems arose with the supply of water. Such a malfunction can occur due to:

  • inlet valve;
  • the failure of the flood valve (clogged, broke down, and t.D.);
  • incorrect connection of the drain system
  • leakage in the pallet of the dishwasher.

Talking about the above problems may also be an error code that is displayed on the dashboard. E15. The code and the blinking indicator can warn the owner of household appliances and about the problems that arose in the system of protection against “Aquastop” leaks. If the system has a leak, water enters the tray. The float sensor gives a signal to the system and an error code is displayed on the display.

You can try to eliminate the problem yourself, but this will require certain knowledge and skills. Inappropriate actions can only aggravate the problem.

  • Water in the pallet. Deanate the dishwasher. Tilt the body of the equipment so that the float is in a normal position. Drain the water from the pallet. Leave the equipment for a while so that the assembled moisture can dry.
  • Water supply problems. Cross the water supply. To do this, you need to close the filling valve. Check for the presence of blockages available in the filter system. Check for excesses and clogs of the flood hose. Disconnect it from the system if necessary and rinse it with water. Check the inlet valve.
  • Spray. Having opened the door of the loading bunker, remove the pallets. Remove the upper and lower sprayer, rinse them.
  • The leak sensor. A faulty sensor can give the system incorrect data and the control module does not launch the bay. It will require replacing the failed sensor.
  • Simple. Normally, the drain hose is located from the floor at 45 cm level. Compliance with this standard and the correct bend of the hose will minimize the risk of self.sample water into the sewer during the bay.

Bosch SPV40E30ru

Bosch machine shifts flashes. What is it? And what to do?

Answers 3

Check at what point the indicator flashes? The car is working properly at the same time?

I had it when I started the car, they started starting, and then I wanted to change the program. If you close the car, it will continue to work. But if you want to change the program, click and hold the start button 3 seconds.(stop the current cycle), then turn off the machine, turn on and install the desired program. Uraaaa.

Varieties of errors on devices with digital display

Most modern Bosch dishwashers are equipped with such digital panels. Error indicators will burn on them if it was not possible to start the process of washing dishes. This facilitates the diagnostic process, and therefore the speed of repair. It is extremely recommended to repair such complex equipment on its own. Contact the appropriate service center. We remind you, do not forget to transfer the Bosch dishwasher into service mode.

  • Uniform flashing of all indicators. a software failure;
  • E01. breakdown of the control unit;
  • E1, F1. sensors malfunctions;
  • E02. wiring breaks;
  • E2, F2. errors when heated;
  • E03. drying does not occur;
  • E3, F3. the tank is not filled;
  • E04. see E02;
  • E4, F4. malfunction of the spraying mechanism;
  • E05. see E01;
  • E5, F5. leak or overflow of the tank;
  • E06. the camera is leaky (problems with the locking mechanism);
  • E6, F6. failure of the quality sensor of incoming water;
  • E07. fan breakdown;
  • E7, F7. blockage of the drain pipe;
  • E8, F8, E08. low water level;
  • E9, F9, E09. problems with the nutrition of the heating system;
  • E10, F10. see E03, E07;
  • E11, F11. there is no data from the temperature sensor;
  • E12, F12. pollution of the heating element with a lime plaque;
  • E13, F13. too high the temperature of the incoming water;
  • E14, F14. error in the water distribution system;
  • E15, F15. tank leak;
  • E16, F16. valve leak;
  • E17, F17. too powerful pressure of incoming water;
  • E18, F18. See E3, E14;
  • E19, F19. malfunction in the system;
  • E20, F20. problems with the pump;
  • E21, F21. See E3, E20;
  • E22, F22. blockage of a drain system;
  • E23, F23. breakdown of the pump responsible for removing water from the tank;
  • E24, F24, E25, F25. see E22;
  • E26, F26. damage to the flow sensor;
  • E27, F27. problems with the mains;
  • E28, F28. see E6;
  • E29, E30, F29, F30. See E27.

Modern dishwashers are supplied with a large number of sensors and appropriate alarms. Additional electronics simplify the work with the device, and in the event of a malfunction, it allows you to quickly determine the breakdown. But you need to be able to work with such signaling devices and know what they mean.

What do indicators mean on the Bosch panel

Depending on the type of dishwasher, the control panel is located either in the upper part of the door (built.in PMM), or on the outside (separate models). Machines with mechanical control are equipped with such indicators:

  • Brush (1) denotes the stage of the washing.
  • End (2). end of the sink.
  • The crane (3) is on. the supply of water to the system.
  • Icons in the form of arrow (4). indicate the presence or absence of salt.
  • Snowflake (star) (5). indication of the rinseum.

Models of dishes with the screen look like this:

The display may be displayed, the values ​​of which are in the instructions:

  • 1. temperature adjustment from 65 to 75 degrees.
  • 2. automatic mode (Auto).
  • 3. temperature adjustment from 35 to 45 degrees.
  • 4. an economical program at 50 ° (ECO).
  • 5 (glass with a cup). fast program at 45 ° C.
  • 6 (shower). preliminary rinse.

Also, the following designations can be found on Bosch dishwashers:

  • A children’s bottle is drawn. a hygienic mode, in which the dishes are treated with hot water.
  • Wave.shaped lines with a plus sign. additional drying.

In separate PMM models there is an indication of the end of the sink. It can be combined with a sound signal. This is a “ray on the floor”: throughout the program, the ray burns in red light, and at its end. green.

Deciphering light bulbs

Some LEDs glow constantly, others do not burn at this time. The former means the modes and programs in which the washing passes.

  • The “brush” light shines. there is a wash of the dishes.
  • Salt arrows caught fire. salt ends in the tank of the ion exchanger. If after adding it does not stop glowing, try to mix the salt in the department.

Some users turn to the master if one of the indicators constantly flashes. Most often this happens with the “crane” LED, at the same time “END” can blink. Why is this happening:

Water is not poured into the chamber. This can happen if the shut.off valve is blocked or not water in the system. Additionally, such elements are checked for the blockage and performance: a filter, filter, entrance valve.

To check the membrane of the intake valve, it is enough to apply for the coils of the operating voltage 220 V. If the membrane opens, it means that the part is working, if not, you need a valve replacement.

There were problems in the electronic board, the contacts burned out or the simistor burned down. Each systemist is responsible for the work of one of the PMM details. As a result of a short circuit, one of them could be damaged.

The protection against the “Aquastop” leakage worked. Mechanical protection is in the intake hose. As soon as the leak occurs, a special sponge is impregnated with water and blocks water access to the system. Only a complete replacement of the hose will help.

Additional options can also be used in PMM, depending on the model. Sometimes they are displayed on the display or touch panel. So:

In separate Bosch models, you can find such a useful function as a “beam on the floor”. This indication warns the user about the end of the sink. It is installed mainly on fully or partially built.in machines. Their panel is often hidden behind the facade, which reduces the sound volume. The bulb glows below the door. She can report on the end of the sink in different ways:

  • At the end, the red point burns on the floor.
  • The bulb glows the entire program, and at the end it turns off.
  • The beam is changing. From red it becomes green or blue.

Why bulbs blink?

Flashing indicators can report a malfunction in the dishwasher. Often the diagnostic system in machines without a display is only triggered. Having decrypted the value of the code, you can quickly find a breakdown site.

If you are faced with a problem when the unit does not fill water, do not panic. At the same time, the “crane” and “end” diodes blink on the panel simultaneously. You can hear the buzz of the valve, but for some reason there is no water. Here are the main reasons:

  • Low pressure in the highway.
  • The intake valve is blocked.
  • A flood hose or a filter set clogged.
  • Protection from the leaks “Aquastop” worked.

It also happens that at the same time the LED of the water supply and detergent flashes. After the check, it turns out that the water enters the camera, and you only poured the product into the compartment. What is the reason? Check the circulation pump. This node supplies fluid under the pressure of sprayers. For accurate diagnosis, it is better to contact a specialist.

This is how you can determine what the indication on the dishwasher means. In some cases, the master can not do without the help.

Bosch PMM errors with display

Errors on Bosch dishwashers with a display are displayed in alphanumeric format E; At the same time, in some models, instead of the prefix “e”, prefix f “is used. The table below will be codes with both prefixes. In addition, we decided to include in this table and an error message on the PMM without a display: in the usual mode of operation of the device, the “crane” indicator is only flashing or on some problem, and to clarify the error we must go to the diagnostic mode.

Even in modern Bosch PMM models, far from all errors are displayed in the usual operating mode of the machine: their full set is available only in service (test or diagnostic) mode, which is launched by a special combination of buttons on the control panel. How to go to service mode will be described in the next section.

Unfortunately, there is no single standard in the Bosch dishwasher error system: several sets of codes are known. In order not to clog the page with a repetition with a description of the same errors, we have collected in one table all the well.known codes of errors: after all, you will still worry a specific problem, and for the harmony of the error numbering system. Where the same code will mean different errors, we will definitely inform about this. Please note that the codes “E01” and “E1” (without zero). These are different mistakes.

Systems in the system for the dishwasher or the control module is faulty. If the reloading of PPM did not help, you need to call a specialist for diagnosis.

You yourself can do little in such a situation, but you can still try:

  • First, check the voltage in the mains: if it is clearly too low or high, call the electrician
  • Check the wires leading to electronic boards for a cliff or short circuit, make sure that all connectors on the boards are tight in the nests
  • Alas, something happened in electronics: you can’t do without a specialist

Water heating does not begin, since problems with signals from one of the sensors or heater are found:

  • One of the sensors is faulty. Thermal attemptor (termistor) or water level sensor (Pressostat). Diagnostics and replacement
  • Too much water flooded into the tank (for example, due to a faulty level sensor)
  • The temperature sensor (thermostat): replacement works incorrectly
  • Cliff in the control circuit of the heater: to ring the circuit, tighten the contacts and fix the wiring
  • Closing in the heating chain, leakage on the case
  • The heater burned: only change it
  • Problems with a controller controller: have to change. Call the workshop

Most likely, something happened to the heating heater

As a result, the water temperature in the tank will differ from the given one, which will affect the quality of the sink:

  • First, make sure that the wiring between the sensor or the heater and the controller controller is in order that all the contacts and the connectors are securely fixed
  • The absence of a signal from the sensor may mean its malfunction: a faulty sensor is changed
  • Problems in the control controller: professional diagnosis and replacement of the controller are required here

The problem with the relay of an additional heater controls the work of the heater

Depending on the model, the dishwasher will either wait for the full filling of the tank with water (as it was in the early models), or after a minute the sink will stop (a more reasonable solution in modern models)

  • Water does not enter the PMM: the water supply valve, a weak pressure in the water supply, a defect or blockage of the hose, the input valve is blocked, etc.d all this is quite possible for you to fix it yourself
  • Forgot to close the door tightly and electronics blocks the launch of the washing program
  • The input electroblop has broken: it will have to be replaced
  • The water level sensor (Pressostat) is faulty: Diagnosis with subsequent replacement
  • Clops in the wiring or contacts departed in circuits from the control controller to the input valve or press stratum
  • Controller’s controller failure: professional diagnosis and replacement are required if the board is faulty

New Bosch dishwasher doesn’t dry.

A problem has been discovered with a flow sensor (switch): it is in a wrong position, but the error can be caused by other reasons:

  • Dishes in the cell block the rotation of the sprayer
  • Cliff in the circuit of the flow sensor
  • The flow sensor broke or clogged: to clean if it did not help. replacement
  • Something happened to the motor, who changes the position of the sensor
  • Problems with the controller controller

The pressure sensor or float signals the overflow of the machine: usually the reason in the blockage or malfunction of the water supply tract:

  • Cliff in the press start chain: fix the wires and fix the contacts
  • Pressostat is faulty: it must be checked and replaced
  • “Bumps” the flood valve, which is why the water constantly enters the car: testing and replacement
  • Matching electronics: you can explain anything with her problems with it

As a result, electronics block the beginning of the sink. Possible reasons:

  • Breeds of communication between the system of control of the door sensor and the controller controller: to call the circuit, check the contacts
  • Something broke in the door lock: in principle, the lock can be fixed on your own
  • The door closure sensor is faulty: replacement
  • Problems in the control controller: diagnosis and replacement

The sink continues based on the assumption of strong pollution

  • Clean the camera of the dishwasher
  • Cliff in the sensor circuit: check and fix the wiring, fix the contacts
  • The sensor itself is faulty: it is only under replacement
  • Problems with the controller controller: the master will have to be called

Bosch Dishwasher Doesn’t Dry Dishes. (FIXED) ✨

The indicator on the Bosch dishwasher burns or flashes, what to do?

What to do if the indicator on the Bosch dishwasher burns or flashes, how to drop an error? The article describes in detail the popular breakdown of Bosch dishwasher, causes of breakdowns and popular methods of elimination.

Do not immediately panic and rush to call the masters of the service center.

  • If the indicator burns brightly, and the dishwasher at the same time functions normally, the water beam has begun.
  • If the work of the technique has stopped, characteristic sound signals in the form of a squeak are heard, the indicator burns brightly or flashes. it is necessary to intervent a specialist.

“Khranik” is located next to the water supply button. The operation of the light signal means that problems arose with the supply of water. Such a malfunction can occur due to:

  • inlet valve;
  • the failure of the flood valve (clogged, broke down, and t.D.);
  • incorrect connection of the drain system
  • leakage in the pallet of the dishwasher.

Talking about the above problems may also be an error code that is displayed on the dashboard. E15. The code and the blinking indicator can warn the owner of household appliances and about the problems that arose in the system of protection against “Aquastop” leaks. If the system has a leak, water enters the tray. The float sensor gives a signal to the system and an error code is displayed on the display.

You can try to eliminate the problem yourself, but this will require certain knowledge and skills. Inappropriate actions can only aggravate the problem.

  • Water in the pallet. Deanate the dishwasher. Tilt the body of the equipment so that the float is in a normal position. Drain the water from the pallet. Leave the equipment for a while so that the assembled moisture can dry.
  • Water supply problems. Cross the water supply. To do this, you need to close the filling valve. Check for the presence of blockages available in the filter system. Check for excesses and clogs of the flood hose. Disconnect it from the system if necessary and rinse it with water. Check the inlet valve.
  • Spray. Having opened the door of the loading bunker, remove the pallets. Remove the upper and lower sprayer, rinse them.
  • The leak sensor. A faulty sensor can give the system incorrect data and the control module does not launch the bay. It will require replacing the failed sensor.
  • Simple. Normally, the drain hose is located from the floor at 45 cm level. Compliance with this standard and the correct bend of the hose will minimize the risk of self.sample water into the sewer during the bay.

Do not try to fix the problem yourself. Seek for help in specialized service centers. Experienced craftsmen will quickly eliminate the problem of water bay.

Bosch SPV40E30ru

Bosch machine shifts flashes. What is it? And what to do?

Answers 3

Check at what point the indicator flashes? The car is working properly at the same time?

I had it when I started the car, they started starting, and then I wanted to change the program. If you close the car, it will continue to work. But if you want to change the program, click and hold the start button 3 seconds.(stop the current cycle), then turn off the machine, turn on and install the desired program. Uraaaa.

Modern dishwashers have quite a lot of different indicators, which the owners pay attention to infrequently, and in vain. The indicator can indicate in time a particular problem in particular, if it does not just burn, but flashes. Suppose a brush at the Bosch dishwasher blinks. What does this mean? Maybe this is a breakdown, a small failure or at all that does not mean the behavior of a “home assistant”? Now we will try to figure it out.

It turns on

Some owners complain of spontaneous turning on the sink: in this case, you also need to check the control board, but often the reason is the plugging of the power button or transition of the PMM into demo mode: in the latter case, you just need to reset the machine settings.

If it did not help, the reason may be in disturbed wiring or breakdown of the control module. It is unlikely that you yourself will be able to determine the exact cause. Better to call the service.

Frequent causes of breakdowns of the dishwasher Bosch

If the problems with work began after buying a machine, pay attention to the settings. Is work organized correctly? The correct connection of communications, pouring and drain hoses matters.

What breakdowns happen more often than others:

  • The technique does not start. Indicators do not burn on the panel, the system does not respond to keystrokes.
  • The defense “Aquastop” is triggered. The reason for the leakage of water in the pallet or malfunction of the float sensor.
  • Water does not merge or does not get. The point is filters, tracts. Malfunction of circulation pump or pump.
  • The program hung after the start of the sink. Holes of openings for water intake, electronic control breakdown. Luke’s malfunction is also possible.

Problems can be manifested by error code on the screen. The electronic board is associated with all nodes through wiring. If one of them does not answer, does not respond to signals, self.diagnosis starts. You will find the decryption of the code in the instructions or in the publication “Code of errors of the dishwasher Bosch”.

  • E01/F01. electronics failure, breakdown on the case of Ten.
  • E09/F09. the operation of the heating element is impaired.
  • E3/F3. water is not poured into the bunker.
  • E22/F22. Filter blockage.
  • E24/F24. E25/F25. Problems with the drain of a spent liquid.
  • E15/F15. the Aquastop system worked.
  • E27/F27. voltage surges in the network are recorded.

Some malfunctions are eliminated with your own hands. Do not rush to call the master right away, figure out the reason for the breakdown of the dishwasher. If, after excluding blockages and errors, the car does not start normal work, then start repairing.

How to repair a dishwasher yourself?

There are two characteristic problems for the Bosch PMM models. They are associated with water. Often users complain about the manifestation of the E15 code on the display. This indicates the operation of the defense “Aquastop”. But it’s not always a leakage. Perform the following actions:

  • Raise the PMM case back and look into the pallet.
  • If water really accumulated there, drain it.
  • Return the float switch to the “Off”.

Sometimes the reason for the operation is the incorrect placement of the gasket of the pouring hose. Perhaps she shifted when installing. Therefore, carry out the connection, following the user management.

The dishwasher does not turn on

You connected the car to the network, pressed the “Turning on” button, but nothing happens? The panel bulbs do not burn, no sound signals are heard. What needs to be checked:

  • Network wire. Sometimes it is too much if during the rearrangement it is pressed by the body of the dishwasher. If you notice damage to isolation, do not do home.made twisting. This approach can lead to a fire. Replace the cord immediately.
  • Fork. The presence of melting and pogars indicates a breakdown. Install a working element.
  • Outlet. To check its performance, connect another device. Works? So the outlet is in good.

It is worth checking the network filter (capacitor). It is located near the engine. During visual inspection, they should be alerted into swollen. The detail is subject to replacement. You can buy it inexpensively in the online store.

Leave problems with electronics and control unit. The exact diagnosis is needed here, which is carried out by a multimeter.

Malfunctions of the fence and drain of water

With such problems, simple inattention should be excluded. So, it is worth checking:

  • Is a shut.off valve open. Perhaps he was accidentally blocked.
  • Is the flood hose exactly. If it is overheated, overwhelmed by an extraneous object, the water will not flow.

When installing the hose with the protection “Aquastop” you need to monitor its work. When the system is triggered, the absorbent is warmed by moisture, which is why it blocks the passage. This is a protection of one.time operation, so you need to completely change the hose.

It is important to maintain a dishwasher at least once every 1-2 weeks.

Service includes cleaning the system from garbage:

  • Rinse it from blockage.
  • Check the inlet valve. Inspect its holes. When the garbage hits the passage, the passage is closed, which makes it difficult to move the membrane. It does not open, and the liquid does not act.

With problems with the drain, the pump is not necessarily broken. Check the details for the blockage:

  • Tear out and clean the part.
  • Check the pump impeller. Pieces of food, penetrating through the filter, can block its rotation.
  • Remove the water from the hole.
  • Remove the lid by pulling.
  • Put on gloves, remove blockage.

Why the indicator shines

If you find that on the panel of the Bosch dishwasher, the indicator with a crane sign is on, but the dishwasher works in the usual mode, then water began to enter the car, and the alarm is false. If, with a flashing indicator, the dishwasher makes strange sounds similar to a squeak, and the water is not typed in the bunker, it means that the part was out of order or faults occurred.

It should be understood that the “crane” sign means the lack of water supply, the following factors can be the reason for this behavior:

  • blocking filter;
  • malfunctions in the operation of the filling valve, due to breakdown or blockage;
  • incorrect connection of the drain system, which is why it occurs on its own;
  • The spray of water works malfunctioning.

All these signs of a malfunction of the Bosch washing machine fit in the short error code E15. In addition, the crane may mean a failure in protection mode from the Aquastop leaks. It often happens that a leak occurs due to the fault of the user, and protection is triggered. It is important to control the amount of detergent that you add to the nest.

Depending on the “Bosch” model, protection against leaks may be complete or partial. The pallet of the machine is filled, and the sensor that controls the water level is triggered. As a result. on the display you see an error code. If the protection is partial, then when a large amount of water is formed, the absorbing sponge is drained with liquid and closes access.

The buttons do not react

Symptoms: none of the control buttons reacts to pressing

If at the same time, nothing burns on the electronic board, then the problem is most likely in the electrical wiring: there are many possible reasons, including the failure of the same control board. read our article, the dishwasher does not turn on.

bosch, dishwasher, blinks, brush

If all indicators blink, then with a high degree of probability of a problem in the control module.

If any one specific button does not react, then the reason can be like a mechanical (saping, sticking), electrical (something wrong with the button contacts) or the button is simply blocked in accordance with the current washing mode-read the instructions.

Designation of signs on the dishwasher

The location of the panel depends on the type of dishwasher. If it is a built.in model, keys and indicators are located on the door of the door. Since the facade part is attached in the built.in PMM, there is no need to put the control system on the front of the door.

Separate cars are a full.fledged element of the interior, so the control panel is located on the facade part. Buttons and indicators can be signed, but often these are foreign names that you cannot break without instructions. It is more convenient when the keys are indicated by the symbols: a pan, snowflake, asterisk. Then the user can intuitively understand the values ​​of the buttons.

The variety of characters depends on the brand of the machine (“Ikea”, “ariston”, “siemens”). As well as from the number of functions of the model.

Consider the designations of the most popular brands of dishwashers.

Bosch (Bosch)

Bosch dishwashers. the most popular in the market. Manufacturers have created a wide range, a wide variety of modes and introduce new technologies. Consider the decoding of the most common characters (follow the numbering in the picture).

  • Poster with a stand (1). The symbol speaks for itself. an intensive regime (70 degrees), which allows you to wash strong pollution from pots, disgusting, pans. Duration. 115 minutes, water consumption. 21 liters.
  • Auto (cup on saucers) (2). “Automatic” mode (we can say “standard”) passes at a temperature of 45-65 degrees. Suitable for various dishes, except for products from delicate material. Opening hours. 140 minutes, consumes 19 liters.
  • ECO (economical washing) or a glass and a cup on a plate (3). The preliminary rinse is originally carried out, and then the program at 50 ° C. Lasts 140 minutes, spends 14 liters.
  • A glass with a cup on a stand and two arrows to the right (4). a quick cycle without primary rinsing at 45 degrees. Characteristics: 30 minutes, 10 l.
  • “Shower” from drops of water (5). “preliminary rinsing”. The program allows you to clean the dishes of food residues, prepare devices for a thorough sink. Time: 19 minutes, water: 4 l.
  • One glass. Denotes “delicate washing”, works at a temperature of 40 degrees. In this case, you can wash fragile products. Takes 75 minutes, spends 15 liters.
  • Plus and minus with the letter (6). allow you to adjust the cycle time.
  • Watch with arrows to the right (7). reduction of the duration of the regime twice (Variospeed).
  • ½ (8). half loading mode. If you have not collected dirty dishes for a full cycle, load only half with 30% saving resources.
  • Poster with rockers (9). “Intensive Wars” (Intensivezone). In the lower part, the water enters under a stronger pressure than in the upper.
  • Children’s bottle (10). Hygienic mode allows you to treat dishes at high temperature. Perfectly disinfects children’s dishes.

Start and Reset keys on the panel will help start the sink cycle or reload.

In addition, the management of the dishwasher is equipped with indicators of work. They inform the user about a particular program. We will figure out how to understand the values ​​of the bulbs on the Bosch panel.

  • Brush (1). Moika indicator.
  • End (2). ending the program.
  • Crane icon (3). water supply light.
  • Wave.shaped arrows (4). indicator of the presence or absence of salt in the ion.exchanger.
  • Sunny (snowflake) (5). the presence of a rinseum in the compartment.

In dishwashers with a display, the sink modes are also equipped with bulbs. If they glow, the program is coming.

  • Icon (1)-the possibility of choosing temperature in the region of 65-75 ° C.
  • Auto (2). automatic washing.
  • Symbol “.”. temperature range from 35 to 45 degrees.
  • ECO (4). economical program.
  • A glass and a cup on a stand (5). fast washing.
  • Water jets (6). preliminary rinsing.

There is also a time indicator on the floor and on the display. In the first case, the numbers are displayed on the floor, which indicate the time before the end of the program. In the latest models there is a “ray on the floor” function. Instead of a sound signal about the end of the cycle, the machine highlights the beam.

Why the indicator blinks

It happens that the bulbs on the dishwasher begin to flash, notifying the user about the violation in the program. If the “Kne” indicator and the “End” icon flashes, there are problems when water supply. What is the reason:

Read more about this in the publication is the “Kran” indicator in the Bosch dishwasher.

HotPoint Ariston (Ariston)

Dishwasher of production “Ariston” easier in management. The designations on their panels are understandable and easily remembered by the user.

  • Indicator indicated letter (1) reports the presence of salt. The one indicated by the cross indicates the number of rinseum.
  • Poster with three lines (2). intense washing under strong water pressure. Duration. 2 h 25 min (± 15 min).
  • Poster with two stands (pan with a circle) (3). a normal sink mode. Lasts 1 h 50 min (± 10 min).
  • ECO (4). “Economical” mode. Environmental washing at 50 degrees. Time: 2 h 35 min (± 15 min).
  • The letter “r” in a circle (5)-express-soil and drying of dishes. For poorly chopped dishes. In just 25 minutes, it will clean 10 items immediately after eating.
  • Three wave.shaped lines (6). mode “soaking”. If you do not have time to start a full cycle, or dried pollution remained on the dishes, press the key 6.
  • Glasses (7). “delicate sink”. Lasts 1 hour 30 minutes (± 10 min), works at low temperature.
  • Number 8. Starting key.
  • Button “P”. selection of mode.

What do indicators mean on the Bosch panel

Depending on the type of dishwasher, the control panel is located either in the upper part of the door (built.in PMM), or on the outside (separate models). Machines with mechanical control are equipped with such indicators:

  • Brush (1) denotes the stage of the washing.
  • End (2). end of the sink.
  • The crane (3) is on. the supply of water to the system.
  • Icons in the form of arrow (4). indicate the presence or absence of salt.
  • Snowflake (star) (5). indication of the rinseum.
bosch, dishwasher, blinks, brush

Models of dishes with the screen look like this:

The display may be displayed, the values ​​of which are in the instructions:

  • 1. temperature adjustment from 65 to 75 degrees.
  • 2. automatic mode (Auto).
  • 3. temperature adjustment from 35 to 45 degrees.
  • 4. an economical program at 50 ° (ECO).
  • 5 (glass with a cup). fast program at 45 ° C.
  • 6 (shower). preliminary rinse.

Also, the following designations can be found on Bosch dishwashers:

  • A children’s bottle is drawn. a hygienic mode, in which the dishes are treated with hot water.
  • Wave.shaped lines with a plus sign. additional drying.

In separate PMM models there is an indication of the end of the sink. It can be combined with a sound signal. This is a “ray on the floor”: throughout the program, the ray burns in red light, and at its end. green.

Deciphering light bulbs

Some LEDs glow constantly, others do not burn at this time. The former means the modes and programs in which the washing passes.

  • The “brush” light shines. there is a wash of the dishes.
  • Salt arrows caught fire. salt ends in the tank of the ion exchanger. If after adding it does not stop glowing, try to mix the salt in the department.

Some users turn to the master if one of the indicators constantly flashes. Most often this happens with the “crane” LED, at the same time “END” can blink. Why is this happening:

Water is not poured into the chamber. This can happen if the shut.off valve is blocked or not water in the system. Additionally, such elements are checked for the blockage and performance: a filter, filter, entrance valve.

bosch, dishwasher, blinks, brush

To check the membrane of the intake valve, it is enough to apply for the coils of the operating voltage 220 V. If the membrane opens, it means that the part is working, if not, you need a valve replacement.

There were problems in the electronic board, the contacts burned out or the simistor burned down. Each systemist is responsible for the work of one of the PMM details. As a result of a short circuit, one of them could be damaged.

The protection against the “Aquastop” leakage worked. Mechanical protection is in the intake hose. As soon as the leak occurs, a special sponge is impregnated with water and blocks water access to the system. Only a complete replacement of the hose will help.

When the “brush” indicator burns, the problem is also in the Aquastop, only the electronic type is in the pallet. Когда вода наполняет поддон, всплывает поплавок — в результате на модуль подается сигнал о протечке. But sometimes the float can stick. To get rid of the problem, tilt the body of the dishwasher from side to side.

The master can accurately determine the cause of flashing bulbs on the panel. Watch useful videos:

Author

Laidred

| Denial of responsibility | Contacts |RSS